OWNER’S MANUAL
© 2005 MILLER Electric Mfg. Co.
OM-226 231B
Use above FORM number when ordering extra manuals.
2006−12
ProHeat 35 Running Gear
CST 8-Pack Running Gear (195 436)
1. Safety Symbol Definitions
Warning! Watch Out! There are possible hazards as
shown in the adjoining symbols.
Falling equipment can cause serious personal injury and
equipment damage. Use lifting eye to lift unit only, not any
other accessories. Use equipment of adequate capacity
to lift unit.
Beware of electric shock from wiring. Keep all panels and
covers closed.
Have only trained and qualified persons install, operate,
or service this unit. Call your distributor if you do not
understand the directions. For INDUCTION HEATING
SAFETY and EMF information, read power source
Manual.
Wear safety glasses with side shields.
2. Tools Needed
9/16 in
OM-226 231 Page 2
3. Installing Running Gear On Power Source
Y Turn off power source and
disconnect input power con-
ductors from deenergized
supply BEFORE moving
power source.
Install casters according to the
illustration. Discard unused hard-
ware.
804 325-A
Hardware Torque Chart
Hardware
Torque
ft-lbs (NVm)
3/8-16x1 20 (27)
Description (Qty)
Part
No.
Item
No.
1 Power Source
2 209 479 Caster (4)
3 601 965 Screw 375-16 x 1.00 Hex (16)
4 010 910 Flat Washer .406 ID x .812
OD x .65 T (16)
5 602 213 Lock Washer .375 Dia (16)
Be sure to provide Model and Serial Number
when ordering replacement parts.
1
2
4
5
3
OM-226 231 Page 3
4. Installing Running Gear On Cooler
Y Turn off power source and
disconnect input power con-
ductors from deenergized
supply BEFORE moving
power source and cooler.
Install casters according to the
illustration. Discard unused hard-
ware.
804 326-A
Hardware Torque Chart
Hardware
Torque
ft-lbs (NVm)
3/8-16x1 20 (27)
Description (Qty)
Part
No.
Item
No.
1 Cooler
2 209 479 Caster (4)
3 010 910 Flat Washer .406 ID x 0.812
OD x .65 T (16)
4 602 213 Lock Washer .375 Dia (16)
5 601 965 Screw 375-16 x 1.00 Hex (16)
Be sure to provide Model and Serial Number
when ordering replacement parts.
1
2
3
4
5
OM-226 231 Page 4
5. Installing Running Gear On CST 8-Pack Rack
804 831-A
Hardware Torque Chart
Hardware
Torque
ft-lbs (NVm)
3/8-16x1 20 (27)
Description (Qty)
Part
No.
Item
No.
1 209 479 Caster (4)
2 601 965 Screw 375-16 x 1.00 Hex (16)
3 010 910 Washer, Flat .406id x 0.812od
x .065t (16)
4 602 213 Lock Washer .375 Dia (16)
5 601 872 Nut, 375−16 .56 Hex (16)
Be sure to provide Model and Serial Number
when ordering replacement parts.
1
2
4
3
5
-
1
-
2
-
3
-
4
Miller PROHEAT 35 RUNNING GEAR Owner's manual
- Type
- Owner's manual
- This manual is also suitable for
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Related papers
-
Miller LA000000 Owner's manual
-
-
-
Miller RUNNING GEAR NO. 22 Owner's manual
-
-
-
-
-
-
