Martin EC 20
The Martin EC 20 is a modular LED block system that allows blocks to be removed and replaced for artistic or repair purposes. Blocks are hot-pluggable, so they can be replaced in seconds, even during a show.
The EC 20 is a versatile system that can be used for a variety of applications, including:
- Video walls: The EC 20 can be used to create large-scale video walls for concerts, sporting events, and other live events.
- Stage sets: The EC 20 can be used to create dynamic and immersive stage sets for theater, opera, and other performances.
- Architectural lighting: The EC 20 can be used to create unique and eye-catching architectural lighting displays for buildings, bridges, and other structures.
Martin EC 20
The Martin EC 20 is a modular LED block system that allows blocks to be removed and replaced for artistic or repair purposes. Blocks are hot-pluggable, so they can be replaced in seconds, even during a show.
The EC 20 is a versatile system that can be used for a variety of applications, including:
- Video walls: The EC 20 can be used to create large-scale video walls for concerts, sporting events, and other live events.
- Stage sets: The EC 20 can be used to create dynamic and immersive stage sets for theater, opera, and other performances.
- Architectural lighting: The EC 20 can be used to create unique and eye-catching architectural lighting displays for buildings, bridges, and other structures.
EC Series LED Blocks
Installation Guide
WARNING! Before installing an EC Series LED block, read “Safety Information” on page 3 of the EC
Series Safety and Installation Guide supplied with EC Series flightcases and available for download
free of charge from the Support pages for the products in the EC Series range on www.martin.com.
WARNING! Installation must be carried out by qualified professionals only. Contact your Martin
supplier for assistance if you have any questions about how to install this product safely.
Important! Take care to avoid damage to LED blocks. Do not place panels LED-side down unless for
service and on a soft, flat surface.
Video panels in the EC series use a modular LED block system that allows blocks to be removed and replaced
for artistic or repair purposes. Blocks are hot-pluggable, so they can be replaced in a a matter of seconds in the
middle of a show, even if power is applied and a P3 signal is present.
LED blocks are supplied complete with a new O-ring on the connector.
Blocks are supplied as either Left or Right (as viewed from the front, audience side) units that are not
interchangeable from one side to the other. Blocks are marked LEFT or RIGHT to identify them. Part numbers
are as follows:
EC-10 Left-side (viewed from front) LED block, calibrated. . . . . . . . . . . . . . . . . . . . . . . . . . . P/N 90354310
EC-10 Right-side (viewed from front) LED block, calibrated . . . . . . . . . . . . . . . . . . . . . . . . . P/N 90354300
EC-20 Left-side (viewed from front) LED block, calibrated. . . . . . . . . . . . . . . . . . . . . . . . . . . P/N 90354280
EC-20 Right-side (viewed from front) LED block, calibrated . . . . . . . . . . . . . . . . . . . . . . . . . P/N 90354290
The procedure for replacing EC-10 and EC-20
Left and Right blocks is the same. To replace
an LED block:
1. Use a 2.5 mm Allen key to loosen the three
captive screws on the existing LED block.
Loosen screws a little at a time, moving
frequently from screw to screw to release
the block evenly without stressing it.
2. Pull the module forwards to remove it from
the panel.
3. Place the new LED block into position on
the panel. Tighten the three screws
gradually, moving each screw a little at a
time and moving frequently from screw to
screw to fasten the block in place evenly.
All EC Series and P3 system controller user documentation is available for download free of charge from the
Product Support area at www.martin.com.
TM
©2010-2011 Martin Professional A/S. Information subject to change without notice. Martin Professional A/S and all affiliated companies disclaim liability
for any injury, damage, direct or indirect loss, consequential or economic loss or any other loss occasioned by the use of, inability to use or reliance on
the information contained in this manual. The Martin logo, the Martin name and all other trademarks in this document pertaining to services or products
by Martin Professional A/S or its affiliates and subsidiaries are trademarks owned or licensed by Martin Professional A/S or its affiliates or subsidiaries.
P/N 35000611, Rev. D
2.5
mm
Figure 1: Replacing an LED block
-
1
Martin EC 20 Installation guide
- Type
- Installation guide
- This manual is also suitable for
Martin EC 20
The Martin EC 20 is a modular LED block system that allows blocks to be removed and replaced for artistic or repair purposes. Blocks are hot-pluggable, so they can be replaced in seconds, even during a show.
The EC 20 is a versatile system that can be used for a variety of applications, including:
- Video walls: The EC 20 can be used to create large-scale video walls for concerts, sporting events, and other live events.
- Stage sets: The EC 20 can be used to create dynamic and immersive stage sets for theater, opera, and other performances.
- Architectural lighting: The EC 20 can be used to create unique and eye-catching architectural lighting displays for buildings, bridges, and other structures.
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Related papers
-
Martin EC 20 Installation guide
-
-
Martin ELP WW IP User manual
-
Martin MAC Quantum Wash Installation guide
-
-
-
-
Martin MAC 401 Dual User manual
-
-
Martin MAC Viper Wash DX Installation guide