Raytheon SC125VNV Installation & Maintenance

Category
Washing machines
Type
Installation & Maintenance

This manual is also suitable for

Part No. F232097R1
August 1997
Commercial Laundry
Technical Communications
P.O. Box 990
Ripon, WI 54971-0990
Washer-Extractor
Cabinet Hardmount
Variable-Speed
Model Numbers
SC125VNV UC125VNV
Installation/Maintenance
NOTA: El manual
en español aparece
después del manual
en inglés.
F232097R1
i
Table of Contents
Installation/Maintenance
Safety
Key to Symbols ................................................ 1–2
Safety Decal Location ...................................... 1–3
Operator Safety ................................................ 1–4
Safe Operating Environment ............................ 1–5
Environmental Conditions ............................ 1–5
Machine Location ......................................... 1–6
Input and Output Services ............................ 1–6
AC Inverter Drive ......................................... 1–7
Misuse .............................................................. 17
Installation
Machine Overview ........................................... 2–1
Delivery Inspection .......................................... 2–2
Customer Service ............................................. 2–2
Model Number Familiarization Guide ............. 2–3
General Specifications ..................................... 2–4
Machine Dimensions ........................................ 2–6
Dimensional Clearances ............................... 2–6
Machine Foundation ........................................ 2–8
Mechanical Installation .................................... 2–9
Drain Connection ............................................. 2–11
Water Connection ............................................ 2–13
Electrical Installation ....................................... 2–14
Steam Requirements (Steam Heat
Option Only) .................................................... 2–16
Chemical Injection Supply System .................. 2–17
Control Function Test ...................................... 2–18
Maintenance
Daily ................................................................ 3–1
Beginning of Day ......................................... 3–1
End of Day ................................................... 3–2
Weekly ............................................................. 3–2
Monthly ........................................................... 3–2
Quarterly .......................................................... 3–4
Care of Stainless Steel ..................................... 3–5
Maintenance Checklists ................................... 3–6
Removal from Service
Decommissioning ............................................ 4–1
F232097R1
© Copyright 1997 Raytheon Appliances
All rights reserved. No part of this book may be reproduced or transmitted in any form or by any means without the written
permission of the publisher.
F232097R1
1–1
Section 1
Safety
Anyone operating or servicing this machine
must follow the safety rules in this manual.
Particular attention must be paid to the
DANGER
,
WARNING
, and
CAUTION
blocks which appear throughout the manual.
The following warnings are general examples
that apply to this machine. Warnings specific
to a particular installation or maintenance
procedure will appear in the manual with the
discussion of that procedure.
Be careful around the open door,
particularly when loading from a level
below the door. Impact with door edges
can cause personal injury.
SW025
CAUTION
Dangerous voltages are present in the
electrical control box(es) and at the motor
terminals. Only qualified personnel familiar
with electrical test procedures, test
equipment, and safety precautions should
attempt adjustments and troubleshooting.
Disconnect power from the machine before
removing the control box cover, and before
attempting any service procedures.
SW005
WARNING
Death or serious injury can result if children
become trapped in the machine. Do not
allow children to play on or around this
machine. Do not leave children unattended
while the machine door is open.
SW001
DANGER
This machine must be installed, adjusted,
and serviced by qualified electrical
maintenance personnel familiar with the
construction and operation of this type of
machinery. They must also be familiar with
the potential hazards involved. Failure to
observe this warning may result in personal
injury and/or equipment damage, and may
void the warranty.
SW004
WARNING
Safety
1–2
F232097R1
Key To Symbols
The lightning flash and arrowhead within the
triangle is a warning sign indicating the
presence of dangerous voltage.
The exclamation point within the triangle is a
warning sign indicating important instructions
concerning the machine and possibly
dangerous conditions.
This warning symbol indicates the presence of
potentially dangerous drive mechanisms
within the machine. Guards should always be
in place when the machine is in operation.
This warning symbol indicates the presence of
possibly dangerous chemicals. Proper
precautions should be taken when handling
corrosive or caustic materials.
This warning symbol indicates the presence of
hot surfaces that could cause serious burns.
Stainless steel and steam lines can become
extremely hot and should not be touched.
This warning symbol indicates the presence of
possibly dangerous pinch-points. Moving
mechanical parts can crush and/or sever
body parts.
Ensure that the machine is installed on a
level floor of sufficient strength and that the
recommended clearances for inspection
and maintenance are provided. Never allow
the inspection and maintenance space to
be blocked.
SW020
CAUTION
Never touch internal or external steam
pipes, connections, or components. These
surfaces can be extremely hot and will
cause severe burns. The steam must be
turned off and the pipe, connections, and
components allowed to cool before the pipe
can be touched.
SW014
WARNING
1–3
Safety
F232097R1
Safety decals appear at crucial locations on the
machine. Failure to maintain legible safety
decals could result in injury to the operator or
service technician.
Figure 1–1
MACHINE MAY BE HOT
AND CAUSE BURNS
A
TTE
M
P
T N
O
E
N
TR
Y U
N
TIL
B
A
S
KE
T H
A
S
S
TO
PP
E
D
S
E
R
IO
U
S IN
JU
R
Y
M
A
Y R
E
SU
LT
R
O
T
A
T
I
O
N
SPIN
MACHINE MAY BE HOT
AND CAUSE BURNS
ATTEMPT NO ENTRY UNTIL
BASKET HAS STOPPED
D
O
N
O
T
W
A
S
H
IT
E
M
S
C
O
N
T
A
IN
IN
G
H
A
Z
A
R
D
O
U
S
C
H
E
M
IC
A
L
S
, F
L
A
M
M
A
B
L
E
F
U
M
E
S
O
R
F
L
A
M
M
A
B
L
E
M
A
T
E
R
IA
L
S
.
U
S
E
M
A
C
H
IN
E
W
IT
H
W
A
T
E
R
O
N
L
Y
.
D
O
N
O
T
L
E
T
C
H
IL
D
R
E
N
O
P
E
R
A
T
E
O
R
P
L
A
Y
, W
IT
H
O
R
A
R
O
U
N
D
W
A
S
H
E
R
.
WARNING!
HIGH VOLTAGE INSIDE
DISCONNECT MAIN POWER BEFORE
REMOVING COVER. ONLY SPECIALLY
TRAINED PERSONNEL SHOULD TIURN
POWER ON WHEN COVER IS REMOVED.
THIS MACHINE IS WIRED FOR
208-240V; 3~ 60Hz
P/N 230877
P/N 230206
P/N 230630
P/N 231146
P/N 230693
P/N 231065
P/N 230757
P/N 230216
P/N 230202
(O.P.L. Only)
P/N 230208
(Typical)
CONNECTION
TO WASHER
PUMP
1. Install the liquid supply system with a loop in the
connection hose (see sketch) or locate the liquid pump
below the connection ports to prevent inadvertant
introduction of chemicals into the washer.
2. Use extreme care in handling hazardous chemicals.
Consult container labels for instructions.
MACHINE MAY BE HOT
AND CAUSE BURNS
ATTEMPT NO ENTRY UNTIL
BASKET HAS STOPPED
DO NOT WASH ITEMS CONTAINING
HAZARDOUS CHEMICALS, FLAMMABLE
FUMES OR FLAMMABLE MATERIALS.
USE MACHINE WITH WATER ONLY.
DO NOT LET CHILDREN OPERATE OR
PLAY, WITH OR AROUND WASHER.
MACHINE MAY BE HOT
AND CAUSE BURNS
ATTEMPT NO ENTRY UNTIL
BASKET HAS STOPPED
SERIOUS INJURY MAY RESULT
R
O
T
A
T
I
O
N
SPIN
DISCONNECT MAIN POWER BEFORE REMOVING COVER
ONLY SPECIALLY TRAINED PERSONNEL
SHOULD TURN POWER ON WHEN COVER IS REMOVED
WARNING !
HIGH VOLTAGE INSIDE
DO NOT LIFT MACHINE BY
DOOR HANDLE.
DOOR HANDLE WILL NOT SUPPORT WEIGHT
OF MACHINE.
RESULTING DAMAGE WILL NOT BE COVERED
BY WARRANTY.
DO NOT LIFT MACHINE BY
DOOR HANDLE.
DOOR HANDLE WILL NOT SUPPORT WEIGHT
OF MACHINE.
RESULTING DAMAGE WILL NOT BE COVERED
BY WARRANTY.
CONDUCTORS ONLY
COPPER
Install equipment
ground as per local
code or N.E.C. Arti-
cal 250-95
P/N 230757
MACHINE MAY BE HOT
AND CAUSE BURNS
ATTEMPT NO ENTRY UNTIL
BASKET HAS STOPPED
SERIOUS INJURY MAY RESULT
P/N 230215-1
High leg must be connected to L-3
This machine requires a 208-240 V 3 phase
4 wire system. If the system has a high leg or if
a phase adder is used, the artificial leg or the
high leg must be connected to L-3. If change
of motor rotation is necessart, do not
exchange the L-3 connection.
The ground lug must be connected to a
permanent earth ground.
WARNING ELECTRICIAN
MA015G
Safety
1–4
F232097R1
To provide personal safety and keep the
machine in proper working order, follow all
maintenance and safety procedures presented
in this manual. If questions regarding safety
arise, contact the factory immediately.
Use factory-authorized spare parts to avoid
safety hazards.
Operator Safety
To ensure the safety of machine operators,
the following maintenance checks must be
performed daily:
1. Prior to operating the machine, verify that
all warning signs are present and legible.
Missing or illegible signs must be replaced
immediately. Make certain that spares are
available.
2. Check door interlock before starting
operation of the machine:
a. Attempt to start the machine with the
door open. The machine should not
start with the door open.
b. Close the door without locking it and
attempt to start the machine. The
machine should not start with the door
unlocked.
c. Close and lock the door and start a
cycle. Attempt to open the door while
the cycle is in progress. The door
should not open.
If the door lock and interlock are
not functioning properly, call a
service technician.
3. Do not attempt to operate the machine
if any of the following conditions
are present:
a. The door does not remain securely
locked during the entire cycle.
b. Excessively high water level is evident.
c. Machine is not connected to a properly
grounded circuit.
Do not bypass any safety devices in
the machine.
NEVER insert hands or objects into basket
until it has completely stopped. Doing so
could result in serious injury.
SW012
WARNING
Never operate the machine with a bypassed
or disconnected balance system. Operating
the machine with severe out-of-balance
loads could result in personal injury and
serious equipment damage.
SW039
WARNING
1–5
Safety
F232097R1
Safe Operating Environment
Safe operation requires an appropriate
operating environment for both the operator
and the machine. If questions regarding safety
arise, contact the factory immediately.
Environmental Conditions
Ambient Temperature
.
Water in the
machine will freeze at temperatures of
32° F or below.
Temperatures above 120° F (50° C) will
result in more frequent motor overheating
and, in some cases, malfunction or
premature damage to solid state devices
that are used in some models. Special
cooling devices may be necessary.
Water pressure switches are affected by
increases and decreases in temperature.
Every 25° F (10° C) change in temperature
will have a 1% effect on the water level.
Humidity
. Relative humidity above 90%
may cause the machine’s electronics or
motors to malfunction or may trip the
ground fault interrupter. Corrosion
problems may occur on some metal
components in the machine.
If the relative humidity is below 30%, belts
and rubber hoses may eventually develop
dry rot. This condition can result in hose
leaks, which may cause safety hazards
external to the machine in conjunction
with adjacent electrical equipment.
Ventilation
. The need for make-up air
openings for such laundry room
accessories as dryers, ironers, water
heaters, etc., must be evaluated
periodically. Louvers, screens, or other
separating devices may reduce the
available air opening significantly.
Radio Frequency Emissions
.
A filter is
available for machines in installations
where floor space is shared with
equipment sensitive to radio frequency
emissions.
Elevation
. If the machine is to be operated
at elevations of over 3,280 feet (1,000
meters) above sea level, pay special
attention to water levels and electronic
settings (particularly temperature) or
desired results may not be achieved.
Chemicals
. Keep stainless steel surfaces
free of chemical residues.
Water Damage
. Do not spray the machine
with water. Short circuiting and serious
damage may result. Repair immediately
all seepage due to worn or damaged
gaskets, etc.
Do not place volatile or flammable fluids
in any machine. Do not clean the machine
with volatile or flammable fluids such as
acetone, lacquer thinners, enamel reducers,
carbon tetrachloride, gasoline, benzene,
naptha, etc. Doing so could result in serious
personal injury and/or damage to
the machine.
SW002
DANGER
Safety
1–6
F232097R1
Safe Operating Environment
(Continued)
Machine Location
Foundation
. The concrete floor must be of
sufficient strength and thickness to handle
the floor loads generated by the high
extract speeds of the machine.
Service/Maintenance Space
.
Provide
sufficient space to allow comfortable
performance of service procedures and
routine preventive maintenance.
This is especially important in connection
with machines equipped with an AC
inverter drive.
Consult installation instructions for specific
details.
Input and Output Services
Water Pressure
. Best performance will be
realized if water is provided at a pressure
of 30–85 psi (2.0–5.7 bar). Although the
machine will function properly at lower
pressure, increased fill times will occur.
Water pressure higher than 100 psi
(6.7 bar) may result in damage to machine
plumbing. Component failure(s) and
personal injury could result.
Steam Heat (Optional) Pressure
.
Best
performance will be realized if steam is
provided at a pressure of 30–80 psi
(2.0–5.4 bar). Steam pressure higher
than 125 psi (8.5 bar) may result in
damage to steam components and may
cause personal injury.
For machines equipped with optional
steam heat, install piping in accordance
with approved commercial steam
practices. Failure to install the supplied
steam filter may void the warranty.
Compressed Air
. For machines requiring
compressed air service, best performance
will be realized if air is provided at a
pressure of 80–100 psi (5.4–6.7 bar).
Drainage System
.
Provide drain lines or
troughs large enough to accommodate
the total number of gallons that could
be dumped if all machines on the site
drained at the same time from the highest
attainable level. If troughs are used,
they should be covered to support light
foot traffic.
Power
. For personal safety and for proper
operation, the machine must be grounded
in accordance with state and local codes.
The ground connection must be to a
proven earth ground, not to conduit or
water pipes. Do not use fuses in place of
the circuit breaker. An easy-access cutoff
switch should also be provided.
Replace all panels that are removed to
perform service and maintenance
procedures. Do not operate the machine
with missing guards or with broken or
missing parts. Do not bypass any
safety devices.
SW019
CAUTION
1–7
Safety
F232097R1
Always disconnect power and water supplies
before a service technician performs any
service procedure. Where applicable, steam
and/or compressed air supplies should also be
disconnected before service is performed.
AC Inverter Drive
Machines equipped with the AC inverter drive
require special attention with regard to the
operating environment.
An especially dusty or linty environment
will require more frequent cleaning of the
AC inverter drive cooling fan filter and of
the AC inverter drive itself.
Power line fluctuations from sources such
as uninterruptible power supplies (UPS)
can adversely affect machines equipped
with the AC inverter drive. Proper
suppression devices should be utilized on
the incoming power to the machine to
avoid problems.
A clean power supply free from voltage
spikes and surges is absolutely essential
for machines equipped with the AC
inverter drive. Nonlinear inconsistencies
(peaks and valleys) in the power supply
can cause the AC inverter drive to generate
nuisance errors.
If voltage is above 230V for 200V
installations or above 440V for 400V
installations, a buckboost transformer is
recommended. If voltage is above 240 or
480, a buckboost transformer is required.
Sufficient space to perform service
procedures and routine preventive
maintenance is especially important for
machines equipped with the AC
inverter drive.
Misuse
Never use this machine for any purpose other
than washing fabric with water.
Never wash petroleum-soaked rags in the
machine. This could result in an explosion.
Never wash machine parts or automotive
parts in the machine. This could result in
serious damage to the basket.
Never allow children to play on or around
this machine. Death or serious injury can
result if children become trapped in the
machine. Do not leave children unattended
while the machine door is open. These
cautions apply to animals as well.
Ensure that a ground wire from a proven
earth ground is connected to the ground lug
near the input power block on this machine.
Without proper grounding, personal injury
from electric shock could occur and machine
malfunctions may be evident.
SW008
WARNING
1–8
NOTES
F232097R1
Safety
F232097R1
2–1
Section 2
Installation
This manual is designed as a guide to the
installation and maintenance of the 125-pound
capacity cabinet hardmount washer-extractor.
Machine Overview
The design of the washer-extractor emphasizes
performance reliability and long service life.
The cylinder, shell, and main body panels are
fabricated of stainless steel. The washer-
extractor is mounted on a welded base frame
which supports the bearings, cylinder, and
shell.
The cylinder is supported at the shaft by two
flange-mounted spherical roller bearings
bolted to the A-frame.
The machine uses one motor to drive the
cylinder with a V-drive system in all speeds.
A door-lock system prevents opening of the
stainless steel door when a cycle is in progress.
It also prevents operation of the machine when
the door is open.
An electrically operated drain valve is used
to retain the water and wash solution in the
machine during the wash and rinse steps.
The drain valve closes when power is applied
and opens when power is removed, allowing
the machine to drain in the event of a
power failure.
The cylinder is designed with lifters or ribs
that lift the garments from the wash solution
when the cylinder rotates at slow speed and
allow the garments to tumble back into the
solution. The cylinder is perforated, allowing
the water to pass through and drain from
within during the wash process and extract.
Electrical controls for the machine are housed
in a separate enclosure located underneath the
top cover of the machine.
The washer-extractor uses an AC inverter drive
control which provides six preset motor speeds
using a single motor. The V-computer output
board converts motor logic from the computer
to the correct signals for the AC inverter drive.
In addition, all logic inputs to the computer are
routed through this board.
The AC inverter drive uses special balance
detection software in conjunction with the
V-computer to prevent out-of-balance
conditions. When the AC drive detects an
unbalanced load at the end of a drain step, the
computer will make up to seven attempts to
balance the load. As a fail-safe measure, an
overtravel limit switch is installed.
Liquid supplies can be injected directly into
the machine by a customer-supplied external
chemical supply system. Chemical supply
hose connections are made just below the
vacuum breaker, inside the machine. A
terminal strip in the AC drive module provides
control signals.
Installation
2–2
F232097R1
Delivery Inspection
Upon delivery, visually inspect crate,
protective cover, and unit for any visible
shipping damage. If the crate, protective cover,
or unit are damaged or signs of possible
damage are evident, have the carrier note the
condition on the shipping papers before the
shipping receipt is signed, or advise the carrier
of the condition as soon as it is discovered.
Remove the crate and protective cover as soon
after delivery as possible. If any damage is
discovered upon removal of the crate and/or
protective cover, advise the carrier and file a
written claim immediately.
Customer Service
If literature or replacement parts are required,
contact the source from whom the machine
was purchased or contact Raytheon
Appliances at (920) 748-3950 for the name
and address of the nearest authorized
parts distributor.
For technical assistance, call any of the
following numbers:
(850) 718-1035
(850) 718-1026
Marianna, Florida
(920) 748-3121
Ripon, Wisconsin
2–3
Installation
F232097R1
A record of each machine, including the serial
number, is on file with the manufacturer. The
serial number decal is located at the rear of the
machine. See Figure 2–1. Always provide the
machine’s serial number and model number
when ordering parts or when seeking
technical assistance.
2–5
Installation
F232097R1
Figure 2–1
Model Number Familiarization Guide
Sample Model Number: SC125VNVOU10001
SC
Machine Type C = Cabinet
125
Machine Capacity (pounds dry weight)
V
Type of Electrical Control V = V-Series Microcomputer
N
Actuation Option N = No Coin Meter
V
Speed V = Variable-Speed
O
Electrical Characteristics See Voltage Designation Chart in this section.
U1
Design Series
0001
Option Identification (varies from machine to machine)
SC125VNVOU10001
00000000000
208–240
21
25
60
3
3
125
57
485
500000
MA007F
Installation
2–6
F232097R1
Cabinet Hardmount General Specifications
125-Pound Capacity Models
Overall Dimensions
Overall width, in/mm 48 / 1219
Overall height, in/mm 70 1/2 / 1791
Overall depth, in/mm 56 / 1422
Weight and Shipping Information
Net weight, lb/kg 2316 / 1051
Domestic shipping weight, lb/kg 2421 / 1098
Domestic shipping volume, ft
3
/m
3
168 / 4.76
Export shipping weight, lb/kg 2701 / 1225
Export shipping volume, ft
3
/m
3
---
Wash Cylinder Information
Cylinder diameter, in/mm 42 / 1060
Cylinder depth, in/mm 24 / 609
Cylinder volume, ft
3
/l
19.24 / 545
Perforation size, in/mm 0.188 / 4.76
Perforation open area,% ---
Door Opening Information
Door opening size, in/mm 20 / 508
Ht. door bottom above floor, in/mm 29 / 737
Balance Detection
Vibration safety switch installed Standard
Drive Train Information
Number of motors in drive train 1
Drive motor power, hp/kW 7 / 5.25
2–7
Installation
F232097R1
Cylinder Speeds
Gentle wash/reverse speed, rpm 27
Wash/reverse speed, rpm 37
Distribution speed, rpm 62
Low extract speed, rpm 260
Medium extract speed, rpm 380
High extract speed, rpm 485
Centrifugal Force Data
Gentle wash centrifugal force, Gs 0.25
Wash/reverse centrifugal force, Gs 0.82
Distribution centrifugal force, Gs 2.3
Low extract centrifugal force, Gs 40
Med. extract centrifugal force, Gs 85
High extract centrifugal force, Gs 140
Direct Steam Heating (Optional)
Steam inlet connection size, in/mm 3/4 / 19
Number of steam inlets 1
Steam req. to raise bath
temperature 10°F, lb/kg
Low level
6.34 / 2.88
High level
8.95 / 4.07
Average steam use per cycle, BHP / kg-hr 4.43 / 69.5
Cabinet Hardmount General Specifications
125-Pound Capacity Models (Continued)
Installation
2–8
F232097R1
Machine Dimensions
Dimensional Clearances
Allow a minimum of 24 inches (609 mm) at
the rear and a minimum of 12 inches (304 mm)
at the sides. Recommended clearance at the
sides is 18 inches (457 mm). Figure 2–2
illustrates the machine dimensions.
Note: The dimensions shown are for planning
purposes only. They are approximate and
subject to normal manufacturing tolerances. If
exact dimensions are required for construction
purposes, contact the distributor or the
manufacturer. We reserve the right to make
changes at any time without notice.
Installation
2–10
F232097R1
Machine Foundation
Note: Do not mount on wooden floors,
above ground level, or over basements or
crawlspaces. Installation must be “slab on
grade” or equivalent.
A proper foundation is absolutely necessary
for all models because of the high extract
speed and the G-forces exerted.
Thoroughness of detail must be stressed with
all foundation work to insure a stable unit
installation, eliminating possibilities of
excessive vibration during extract.
The machine must be secured to a foundation
or floor of adequate construction. The floor
must be 3500 psi minimum reinforced
concrete embedded in clean, compacted fill
dirt. The floor must be at least 12 inches
(304 mm) thick.
The machine must be anchored to a
smooth level surface so that the entire base
of the machine is supported and rests on
the mounting surface. (Do not support the
machine on only four points.) If anchor bolts
are used instead of a rebar frame to install the
machine, the anchor bolts must be a minimum
of 3/4-inch diameter, grade 5.
Care must be exercised in the design of the
mounting base due to the force exerted by the
machine during extract.
Static and dynamic loads on the floor or
foundation are shown in the following table,
Cabinet Hardmount Floor Load Data. This
table can be used as a reference when
designing floors and foundations.
Ensure that the machine is installed on a
level floor of sufficient strength and that the
recommended clearances for inspection
and maintenance are provided. Never allow
the inspection and maintenance space to
be blocked.
SW020
CAUTION
Cabinet Hardmount Floor Load Data
125-Pound Capacity Models
Static floor load, lbs/kN 2841 / 12.7
Static pressure, lbs-ft
2
/kN-m
2
178 / 8.5
Maximum dynamic load, lbs/kN 3500 / 15.5
Dynamic pressure, lbs-ft
2
/kN-m
2
219 / 10.5
Dynamic load frequency, Hz 8.08
2–11
Installation
F232097R1
Mechanical Installation
Note: Improper installation may void the
warranty. Consult the manufacturer or your
distributor before deviating from the
following procedures.
A bolt kit consisting of eight bolts is available
as an option. All machines use 3/4–10 x 8"
bolts. The bolts should be embedded in a 3500
psi minimum reinforced concrete floor that is a
minimum of 12 inches (304 mm) thick. Use
the mounting bolt layout in Figure 2–3. (The
front of the washer-extractor is the bottom of
each diagram.)
Figure 2–3
The threaded end of the bolts should extend
two inches above the surface of the floor.
See Figure 2–4 for a typical installation of
individual mounting bolts.
Figure 2–4
A bolt-locator fixture or rebar frame is
available as an option. This rigid welded
assembly made of reinforcing rod and
mounting bolts is designed to be embedded
in concrete. See Figure 2–5.
Figure 2–5
MI003K
Frame
Grout
P010I1A
Reinforcing
Rod
Grouting
Mounting
Bolt Threads
Machine Base
P011I1A
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42
  • Page 43 43
  • Page 44 44
  • Page 45 45
  • Page 46 46
  • Page 47 47
  • Page 48 48
  • Page 49 49
  • Page 50 50
  • Page 51 51
  • Page 52 52
  • Page 53 53
  • Page 54 54
  • Page 55 55
  • Page 56 56
  • Page 57 57
  • Page 58 58
  • Page 59 59
  • Page 60 60
  • Page 61 61
  • Page 62 62
  • Page 63 63
  • Page 64 64
  • Page 65 65
  • Page 66 66
  • Page 67 67
  • Page 68 68
  • Page 69 69
  • Page 70 70
  • Page 71 71
  • Page 72 72
  • Page 73 73
  • Page 74 74
  • Page 75 75
  • Page 76 76
  • Page 77 77
  • Page 78 78
  • Page 79 79
  • Page 80 80
  • Page 81 81
  • Page 82 82
  • Page 83 83
  • Page 84 84
  • Page 85 85
  • Page 86 86
  • Page 87 87
  • Page 88 88
  • Page 89 89

Raytheon SC125VNV Installation & Maintenance

Category
Washing machines
Type
Installation & Maintenance
This manual is also suitable for

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

in other languages