King Canada KC-117FN User manual
- Category
- Power tools
- Type
- User manual
This manual is also suitable for
15” BENCH & FLOOR
DRILL PRESSES
INSTRUCTION MANUAL
COPYRIGHT © 2016 ALL RIGHTS RESERVED BY KING CANADA TOOLS INC.
MODEL: KC-117N MODEL: KC-117FN
10/2016
WARRANTY INFORMATION
2-YEAR
LIMITED WARRANTY
FOR THIS 15” DRILL PRESS
KING CANADA TOOLS
OFFERS A 2-YEAR LIMITED WARRANTY
FOR NON-COMMERCIAL USE.
PROOF OF PURCHASE
Please keep your dated proof of purchase for warranty and servicing purposes.
REPLACEMENT PARTS
Replacement parts for this product are available at our authorized King Canada service centers across Canada.
LIMITED TOOL WARRANTY
King Canada makes every effort to ensure that this product meets high quality and durability standards. King Canada warrants to the
original retail consumer a 2-year limited warranty as of the date the product was purchased at retail and that each product is free from
defects in materials. Warranty does not apply to defects due directly or indirectly to misuse, abuse, normal wear and tear, negligence or
accidents, repairs done by an unauthorized service center, alterations and lack of maintenance. King Canada shall in no event be liable
for death, injuries to persons or property or for incidental, special or consequential damages arising from the use of our products.
To take advantage of this limited warranty, return the product at your expense together with your dated proof of purshase to an authorized
King Canada service center. Contact your retailer or visit our web site at www.kingcanada.com for an updated listing of our authorized
service centers. In cooperation with our authorized serviced center, King Canada will either repair or replace the product if any part or
parts covered under this warranty which examination proves to be defective in workmanship or material during the warranty period.
NOTE TO USER
This instruction manual is meant to serve as a guide only. Specifications and references are subject to change without prior notice.
PARTS DIAGRAM & PARTS LISTS
Refer to the Parts section of the King Canada web site for the most updated parts diagram and parts list.
KING CANADA INC. DORVAL, qUÉBEC, CANADA H9P 2Y4
www.kingcanada.com
GENERAL SAFETY INSTRUCTIONS
FOR POWER TOOLS
1. TO AVOID INJURY FROM PARTS BEING THROWN BY
THE SPRING
Follow the instructions exactly as given and shown in “Adjusting
the quill return spring”.
2. USING A DRILL PRESS VISE
When using a drill press vise, always fasten it to the table.
3. NEVER DO “FREEHAND WORK”
Never do any work “Freehand” (hand holding the workpiece rather
than supporting it on the table) except when you have polishing to
do.
4. SECURE the lock head to the column, table support to column
and table to table support before operating the drill press.
5. NEVER move the head or table while the drill press is running.
6. USE THE RECOMMENDED SPINDLE SPEED for the
specific operation and workpiece material. Check the panel inside
the guard cover for drill information. For accessories, use the in-
structions provided with the accessories.
7. NEVER climb on the drill press table, it could break or pull the en-
tire drill press down on you.
SPECIFIC SAFETY INSTRUCTIONS FOR DRILL PRESS
1. KNOW YOUR TOOL
Read and understand the owners manual and labels affixed to the
tool. Learn its application and limitations as well as its specific po-
tential hazards.
2. GROUND THE TOOL.
This tool is equipped with an approved 3-conductor cord and a 3-
prong grounding type plug to fit the proper grounding type recep-
tacle. The green conductor in the cord is the grounding wire.
NEVER connect the green wire to a live terminal.
3. KEEP GUARDS IN PLACE.
Keep in good working order, properly adjusted and aligned.
4. REMOVE ADJUSTING KEYS AND WRENCHES.
Form habit of checking to see that keys and adjusting wrenches
are removed from tool before turning it on.
5. KEEP WORK AREA CLEAN.
Cluttered areas and benches invite accidents. Make sure the floor
is clean and not slippery due to wax and sawdust build-up.
6. AVOID DANGEROUS ENVIRONMENT.
Don’t use power tools in damp or wet locations or expose them to
rain. Keep work area well lit and provide adequate surrounding
work space.
7. KEEP CHILDREN AWAY.
All visitors should be kept a safe distance from work area.
8. MAKE WORKSHOP CHILD-PROOF.
-with padlocks, master switches or by removing starter keys.
9. USE PROPER SPEED.
A tool will do a better and safer job when operated at the proper
speed.
10. USE RIGHT TOOL.
Don’t force the tool or the attachment to do a job for which it was
not designed.
11. WEAR PROPER APPAREL.
Do not wear loose clothing, gloves, neckties or jewelry (rings,
watch) because they could get caught in moving parts. Non-slip
footwear is recommended. Wear protective hair covering to con-
tain long hair. Roll up long sleeves above the elbows.
12. ALWAYS WEAR SAFETY GLASSES.
Always wear safety glasses (ANSI Z87.1). Everyday eye-glasses
only have impact resistant lenses, thet are NOT safety glasses.
Also use a face or dust mask if cutting operation is dusty.
13. DON’T OVERREACH.
Keep proper footing and balance at all times.
14. MAINTAIN TOOL WITH CARE.
Keep tools sharp and clean for best and safest performance. Follow
instructions for lubricating and changing accessories.
15. DISCONNECT TOOLS.
Before servicing, when changing accessories or attachments.
16. AVOID ACCIDENTAL STARTING.
Make sure the swich is in the ‘’OFF’’ position before plugging in.
17. USE RECOMMENDED ACCESSORIES.
Consult the manual for recommended accessories. Follow the in-
structions that accompany the accessories. The use of improper
accessories may cause hazards.
18. NEVER STAND ON TOOL.
Serious injury could occur if the tool tips over. Do not store materi-
als such that it is necessary to stand on the tool to reach them.
19. CHECK DAMAGED PARTS.
Before further use of the tool, a guard or other parts that are
damaged should be carefully checked to ensure that they will oper-
ate properly and perform their intended function. Check for align-
ment of moving parts, breakage of parts, mounting, and any other
conditions that may affect its operation. A guard or other parts that
are da -maged should be properly repaired or replaced.
20. NEVER LEAVE MACHINE RUNNING
UNATTENDED.
Turn power ‘’OFF’’. Don’t leave any tool running until it comes to a
complete stop.
WARNING
ALL ELECTRICAL CONNECTIONS MUST BE DONE BY A QUALIFIED ELECTRICIAN. FAILURE TO COMPLY MAY RESULT IN SERIOUS
INJURY! ALL ADJUSTMENTS OR REPAIRS MUST BE DONE WITH THE MACHINE DISCONNECTED FROM THE POWER SOURCE.
FAILURE TO COMPLY MAY RESULT IN SERIOUS INJURY!
POWER SUPPLY
WARNING: YOUR DRILL PRESS MUST BE CONNECTED TO A 120V
WALL OUTLET, WITH A MINIMUM 15-AMP. BRANCH CIRCUIT AND USE
A 15-AMP TIME DELAY FUSE OR CIRCUIT BREAKER. FAILURE TO
CONNECT IN THIS WAY CAN RESULT IN INJURY FROM SHOCK OR
FIRE.
GROUNDING
Your drill press must be properly grounded. Not all outlets are properly
grounded. If you are not sure if your outlet is properly grounded, have it
checked by a qualified electrician.
WARNING: IF NOT PROPERLY GROUNDED, THIS DRILL PRESS CAN
CAUSE ELECTRICAL SHOCK, PARTICULARLY WHEN USED IN DAMP
LOCATIONS. TO AVOID SHOCK OR FIRE, IF THE POWER CORD IS
WORN OR DAMAGED IN ANY WAY, HAVE IT REPLACED IMMEDIATELY.
If this drill press should malfunction or breakdown, grounding provides a
path of least resistance for electric current, to reduce the risk of electric
shock. This drill press is equipped with a cord having an equipment-ground-
ing conductor and grounding plug. The plug must be plugged into an appro-
priate outlet that is properly installed and grounded in accordance with all
local codes and ordinances.
WARNING: TO MAINTAIN PROPER GROUNDING, DO NOT REMOVE OR
ALTER THE GROUNDING PRONG IN ANY MANNER.
120V OPERATION
As received from the factory, your drill press is ready to run for 120V
operation. This machine is intended for use on a circuit that has an outlet
and a plug which looks like the one illustrated in Fig.1.
WARNING: DO NOT USE A TWO-PRONG ADAPTOR(S) FOR THEY ARE
NOT IN ACCORDANCE WITH LOCAL CODES AND ORDINANCES.
NEVER USE IN CANADA.
EXTENSION CORDS
The use of any extension cord will cause some loss of power. If you do not
have a choice, use the table in Fig.2 to determine the minimum wire size
(A.W.G-American Wire Gauge) extension cord needed. Use only 3-wire ex-
tension cords which have 3-prong grounding type plugs and 3-hole recep-
tacles which accept the tool’s plug.
For circuits that are further away from the electrical circuit
box, the wire size must be increased proportionately in
order to deliver ample voltage to the drill press motor.
Refer to Fig.2 for wire length and size.
Figure 1
Figure 2
PROPERLY GROUNDED OUTLET
CURRENT CARRYING
PRONGS
GROUNDING
PRONG
Figure 3
TURNING THE DRILL PRESS ON/OFF
This Drill Press comes with a 2 step activation safety switch, refer
to Fig.3, which starts and stops the machine. To turn the Drill Press
on;
1. Push up on the emergency stop button (A) Fig.3 and lift the switch
cover (B) upwards as shown.
2. Press the green On button (C) to start the Drill Press.
3. To stop the Drill Press, you can either press the red Off button (D)
or lower the switch cover and push the large emergency stop but-
ton (E).
ELECTRICAL INFORMATION
Tool’s
Amperage
Rating
3-6
6-8
8-10
10-12
12-16
Cord Size in A.W.G.
Cord Length in Feet
25 50 100 150
18 16 16 14
18 16 14 12
18 16 14 12
18 16 14 12
14 12 - -
MODELS..............................................................................................................................................................KC-117N & KC-117FN
VOLTAGE ........................................................................................................................................................................................120V
AMPS ..............................................................................................................................................................................................7.5A
MOTOR R.P.M. ................................................................................................................................................................................1720
Hz/PHASE....................................................................................................................................................................60 Hz / 1 PHASE
CHUCK CAPACITY ..........................................................................................................................................................................5/8”
SWING ..............................................................................................................................................................................................15”
MAX. SPINDLE TRAVEL ..............................................................................................................................................................3-1/8”
MAX. DISTANCE FROM CHUCK TO THE TABLE (KC-116N / KC-116FN) ..................................................................14-3/4” / 22-1/8”
MAX. DISTANCE FROM CHUCK TO THE BASE (KC-116N / KC-116FN)....................................................................22-3/4” / 43-3/4”
NUMBER OF SPEEDS/RANGE OF SPEEDS ........................................................................................................16 (220-3600 RPM)
SPINDLE TAPER ..........................................................................................................................................................................MT#2
WEIGHT (KC-116N / KC-116FN) ..............................................................................................................................127 LBS / 140 LBS
FIGURE 4
FIGURE 5
GETTING TO KNOW YOUR DRILL PRESS
LOCATION AND FUNCTION OF CONTROLS
1. Belt tension lock knobs...Tightening knobs locks motor
bracket support to maintain correct belt distance and tension.
2. Belt tension handle...Turn handle counterclockwise to apply
tension to the belt, turn clockwise to release belt tension.
3. Head locking set screws...Locks the head to the column. Al-
ways have them locked in place while operating the drill press.
4. Feed handle...For moving the chuck up or down. One or two
of the handles may be removed if necessary whenever the
workpiece is of such unusual shape that it interferes with the
handles.
5. Table handle...Turn clockwise to elevate the table. Support
lock must be released before operating handle.
6. Chuck key...Used to tighten a drill into the chuck and also to
loosen the chuck for drill removal.
7. Chuck...Holds the drill bit or other recommended accessory to
perform desired operations.
8. Depth scale...Allows the operator to adjust the drill press to
drill to a desired depth.
9. Light “ON-OFF” Switch...Turns the light on and off.
10. Drill “2 step activation” Switch.
11. Depth scale lock...Locks the depth scale at the selected
depth.
12. Lasers “ON-OFF” Switch...Turns the lasers on and off.
13. Spring cap...Provides means to adjust the quill spring tension.
14. Table lock...Allows the table to be rotated in various positions
and locked.
15. Table bevel lock...Locks the table in any position from 0
0
to 45
0
.
16. Bevel scale...Shows the degree in which the table is tilted for
bevel operations. The scale is mounted on the side of the arm.
17. Support lock handle...Tightening locks the table support to
the column. Always have it locked in place while operating the
drill press.
SPECIFICATIONS
BASE, COLUMN & TABLE ASSEMBLY
1. Position the base (A) Fig.6 on the floor. Remove the protective
covering and discard.
2. Remove protective sleeve from the column (B) and discard. Place the
column assembly on the base, align the holes in the column support
(C) with the holes in the base.
3. Locate four long bolts from the parts bag.
4. Install a bolt in each hole through the column support (C) and the base
and tighten with the ajustable wrench.
5. Loosen set screw (A) Fig.7 in column collar (B) with 3mm hex. key (C)
and remove collar and rack (D) from the column.
6. Find the elevation worm gear shaft (A) Fig.8 in the loose parts bag. In-
sert the elevation shaft into the table support (B) and extend the shaft
through the opening as far as possible. The crank handle (C) is to be
installed on the elevation shaft, the set screw (D) is to be aligned with
the flat portion of the shaft. The crank is to be positioned as close to
the arm support as possible, then tighten the set screw.
7. With the long smooth end of the rack (A) Fig.9 pointing upwards, slide
rack down through the large round opening in the table support (B).
Engage rack in gear mechanism found inside the opening of the table
support.
FIGURE 6
FIGURE 7
FIGURE 8
FIGURE 9
ASSEMBLY
ASSEMBLY
8. While holding the rack (A) Fig.10 and table support (B) in an engaged
position, slide both down over the column (C). Slide rack down the col-
umn until the rack is positioned against the lower column support (D).
9. Replace column collar (A) Fig.11 and position it bevel side down over
the rack (B). Tighten set screw (C) in collar with 3mm hex. key (D). To
let the rack slide when the table is swung to the left or right around the
column, the collar must sit loosely over the rack and should not be an-
gled on the column. Only tighten set screw enough to keep the collar
in place, otherwise the collar may break due to excessive pressure.
NOTE: To avoid column or collar damage, do not overtighten set screw.
10. Locate the support lock handle (A) Fig.12 in loose parts bag and
tighten by hand.
11. To minimize crank backlash; tighten the support lock handle and ro-
tate the elevation worm shaft clockwise with the crank handle. Loosen
the set screw in the crank and reposition it as close to the table support
as possible. Tighten set screw in the crank handle.
INSTALLING THE HEAD
1. Remove the protective covering from the head assembly (A) Fig.13A.
2. Carefully lift the head above the column and slide it down on the col-
umn as far as it will go. Align the head with the table and the base.
3. Using a 4mm hex. key, tighten both head set screws (B) on the right
side of the head.
INSTALLING PULLEY COVER KNOB OR LOCKING PULLEY COVER
1. Install the knob (A) Fig.13B to the pulley cover (B) using a small pan
head screw (C) as shown in Option #1, Fig.13B.
2. For safety reasons, user may be required to lock the pulley cover to
prevent easy access to the pulleys. This can be done by only using the
small pan head screw (C). Close the pulley cover and screw pan head
screw through the cover and into the tab (D) as shown in Option #2,
Fig.13B.
FIGURE 10
FIGURE 11
FIGURE 12
FIGURE 13B
FIGURE 13A
ASSEMBLY & ADJUSTMENTS
INSTALLING THE CHUCK
1. Locate the chuck (A) Fig.14 in the box of parts.
2. Clean out the tapered hole in the chuck, also clean the spindle nose (B) with a clean
cloth. Make sure there are no foreign particles sticking to the surfaces. The slightest
piece of dirt on the spindle nose or the chuck will prevent the chuck from seating
properly. This will cause the drill to “wobble”.
NOTE: If the tapered hole in the chuck is extremely dirty, use a cleaning solvent on a
clean cloth.
3. Push the chuck up on the spindle nose as far as it will go.
4. Turn the chuck sleeve clockwise and open the chuck jaws completely.
5. Lightly tap the nose of the chuck with a piece of wood to insure the proper seating
of the chuck on the spindle.
REMOVING THE CHUCK & ARBOR
1. Align key holes in spindle and quill (A) Fig.15 by rotating the chuck (C) by hand.
2. Insert drift key (B) into key holes in the quill.
3. Tap key drift key lightly until the chuck and arbor fall out of the spindle.
NOTE: Place one hand below the chuck to catch it when it falls out.
INSTALLING THE FEED HANDLES
1. Locate the three feed handles (A) Fig.16 among the loose parts.
2. Screw the feed handle tightly into the threaded holes in the hub (B).
TENSIONING BELTS / SETTING DESIRED DRILLING SPEED
NOTE: The drill press is shipped with the belts installed, but they should be properly
tensioned before use.
1. Lift the guard (A) Fig.17 from the right side and keep it opened.
2. Release the belt tension lock knobs (B) located on the both sides of the drill press
head. Release tension to the belt by turning belt tension handle (C) clockwise.
Tighten the belt tension lock knobs (B).
3. Choose the desired speed for your drilling operation, and move the belts (D) to the
indicated position on the pulleys (E). Refer to the chart on the inside of the belt guard.
4. Loosen the belt tension lock knobs and turn the belt tension handle (C) counter-
clockwise to apply tension to the belts.
5. Tighten the belt tension lock knobs.
NOTE: The belts should
deflect approximately 1/2” by applying finger pressure at the
mid-point of the belts between the pulleys.
6. Close the belt guard.
7. If the belts slip while drilling, reajust the belt tension.
FIGURE 14
FIGURE 15
FIGURE 16
FIGURES 17
OPERATION & ADJUSTMENTS
WARNING! For your own safety, turn the switch OFF and remove the plug from
the power source before making any adjustements. To avoid injury from thrown
parts due to the spring release, follow instructions carefully and wear safety
glasses.
INSTALLING DRILL BITS
Insert the drill bit (A) Fig.18 into the chuck (B) far enough to obtain the maximum
gripping of the chuck jaws. When using a small drill bit, do not insert it so far that
the jaws touch the flutes (spiral grooves) of the bit.
Make sure the drill bit is centered in the chuck before tightening the chuck with
the chuck key (C). Tighten the drill bit well, so that it doesn’t slip while drilling. Turn
the chuck key clockwise to tighten, counterclockwise to loosen.
DRILLING TO A SPECIFIC DEPTH
To drill a blind hole (not all the way through) to a given depth, proceed as follows.
1. Mark the depth of the hole on the workpiece.
2. Loosen the depth scale lock knob (A) Fig.19.
3. With the switch OFF, bring the drill bit down until the tip of the lips of the drill bit
are even with the mark (B).
4. Turn the depth scale (C) counterclockwise until it stops moving.
5. Tighten the depth scale lock knob.
6. The drill bit will stop at this depth until the depth scale is readjusted.
ANOTHER WAY- DEPTH SCALE
1. With the power OFF, loosen the depth scale lock knob (A) Fig.19.
2. Place workpiece on table. Adjust table until the tip of the drill is just a little above
the top of the workpiece.
3. Turn the depth scale (C) clockwise until the depth scale indicator (D) points to
the desired drilling depth on the scale.
4. Tighten the depth scale lock knob.
5. The chuck or drill will now be stopped after traveling downward the distance
selected on the depth scale.
ADJUSTING THE qUILL RETURN SPRING
NOTE: The return spring tension is set at the factory and should not require further
adjustment.
1. With the chuck at its highest possible position, turn the depth scale (C) Fig.19
clockwise until it stops and tighten the depth scale lock knob (A) Fig.19. This
will prevent the quill from dropping while tensioning the spring.
2. Lower the table for additional clearance.
3. Work from the left side of the drill press.
4. Place screwdriver in the lower front notch (A) Fig.20 of the spring cap (B), and
hold it in place while loosening and removing the outer nut (C) (only).
5. With screwdriver remaining in the notch, loosen inner nut (D) (approx. 1/8”)
until the notch disengages from the boss on the head. Do not remove this nut.
6. Carefully turn screwdriver counterclockwise and engage the next notch (E) in
the boss. Do not remove screwdriver.
7. Tighten nut with wrench only enough to engage boss. Do not over tighten as
this will restrict quill movement.
8. Check tension while turning feed handles.
9. If there is not enough tension on the spring, repeat steps 4-8 moving only one
notch each time and checking tension after each repetition.
FIGURE 18
FIGURE 19
FIGURE 20
OPERATION
FIGURE 21
FIGURE 22
FIGURE 23
ADJUSTING THE TABLE SqUARE TO THE HEAD
1. Insert a precision round steel rod (A) Fig.21 approximately 3” long into the chuck
and tighten.
2. With the table (B) raised to working height and locked into position, place a
combination square (C) flat on the table beside the rod.
3. If an adjustment is necessary, loosen the table bevel lock bolt (D) with an ad-
justable wrench and loosen the set screw (E) below the table bevel lock bolt.
These adjustments are located under the table.
4. Align the table square to the rod by tilting the table.
5. Retighten the table bevel lock bolt. Retighten set screw.
TILTING THE TABLE
To use the table in a bevel position, loosen the bevel lock bolt (D) Fig.21 with an
adjustable wrench. Tilt the table to the desired angle by reading the bevel scale
on the table support. Retighten the bevel lock bolt.
FEEDING
Pull down the feed handles (A) Fig.22 with only enough effort to allow the drill to
cut. Feeding too slowly might cause the drill to burn...feeding too rapidly might
stop the motor...cause the belt or drill to slip... tear the workpiece loose or break
the drill bit.
HOLE LOCATION
Make an indentation in the workpiece where you want the to drill a hole using a
centre punch or a sharp nail. Before turning the switch ON, bring the drill bit down
to the workpiece, lining it up with the hole location.
POSITIONING THE TABLE AND WORKPIECE
Lock the table to the column in a position so that the tip of the drill is just a little
above the top of the workpiece. Always place a piece of back-up material (wood,
plywood) on the table underneath the workpiece. This will prevent splintering or
making a heavy burr on the underside of the workpiece as the drill breaks through.
To keep the back-up material from spinning out of control, it must come in contact
with the left side of the column, as illustrated in Fig.22.
WARNING! To prevent the workpiece or the back-up material from being torn from
your hand while drilling, position them against the left side of the column. If the
workpiece or the back-up material are not not long enough to reach the column,
clamp them to the table. Failure to do this could result in personal injury.
LIGHT &
DUAL LASER GUIDE SYSTEM
WARNING! Do not look directly at the laser beams. Do not aim the laser
beams at any person or any object other than your workpiece.
If you desire using the dual laser guides, use the laser switch (A) Fig.23 to
turn them On or Off. If an adjustment to the laser guides are necessary, pro-
ceed as follows;
1) Loosen set screw (B) (one set screw for each laser) and then slightly turn
laser guide (C) in either direction, this will reposition the laser beams tra-
jectory, adjust the position of the laser guides this way until both beams in-
tersect at the point where the drill bit touches the workpiece. Retighten set
screw after each adjustment.
The light On-Off Switch (D) turns On and Off a halogen light bulb which is found
inside the head casting.
MAINTENANCE / TROUBLESHOOTING
LUBRICATION
All of the ball bearings are packed with grease at the factory. They require no further lubrication. Periodically lubricate the splines (Grooves)
in the spindle and the rack (Teeth of the quill).
WARNING! For your own safety, tur n the switch “OFF” and remove the plug from the power source before maintaining or lubricating your
drill press.
Frequently blow out any dust that may accumulate inside the motor. After operation, remove chips or dirt on the machine and apply a coat
of furniture-type paste wax to the table and the column, this will help keep the surfaces clean and free of rust.
PROBLEM
Noisy operation.
Drill bit burns.
Wood splinters on un-
derside of workpiece.
Workpiece torn loose
from hand.
Drill bit binds in work-
piece.
Excessive drill bit
wobbling.
Quill returns too fast or
too slow.
Chuck will not stay at-
tached to the spindle. It
falls off when trying to
install it.
PROBABLE CAUSE
1. Incorrect belt tension.
2. Dry spindle.
3. Loose spindle pulley.
4. Loose motor pulley.
1. Incorrect speed.
2. Chips not comming out of hole.
3. Dull drill bit.
4. Feeding too slow.
5. Not lubricated.
1. No “Back-up material” under the work-
piece.
1. Not supported or clamped properly.
1. Workpiece is pinching the drill bit or there
is an excessive feeding pressure.
2. Improper belt tension.
1. Bent drill bit.
2. Worn spindle bearings.
3. Drill bit is not properly installed in the
chuck.
4. Chuck not properly installed.
1. Spring has improper tension.
1. Dirt, grease or oil on the tapered inside
surface of the chuck or on the spindle ta-
pered surface.
SOLUTION
1. Adjust the tension.
2. Lubricate the spindle.
3. Tighten the retaining nut on the pulley as needed.
4. Tighten the set screws which hold the puleys in place.
1. Change the speed.
2. Retract the drill bit frequently to clear the chips.
3. Resharpen the drill bit.
4. Feeding too fast...allow the drill bit to cut.
5. Lubricate the drill bit with cutting or motor oil.
1. Support the workpiece or clamp it.
1. Support the workpiece or clamp it.
1. Support the workpiece or clamp it.
2. Adjust the tension of the belt.
1. Use a straight drill bit.
2. Replace the bearings.
3. Install drill bit properly.
4. Install chuck properly.
1. Adjust the spring tension.
1. Using a household detergent, clean the tapered surfaces
of the chuck and the spindle to remove the dirt, grease
and oil.
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
King Canada KC-117FN User manual
- Category
- Power tools
- Type
- User manual
- This manual is also suitable for
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Related papers
-
King Canada KC-117FC User manual
-
-
-
-
-
-
-
-
-