Page is loading ...
Strada Regina Km 3,5 • I 62018 Potenza Picena (MC) • Tel.0733/870.870 • Fax 0733/870.880 • http://www.audison.com
Cod. 10124900
mono
Speaker L
Speaker R
mono
ABS Balanced Inputs
Right
Left
on
peak L
safe
peak R
CONNECTIONS AND FUNCTIONS
Front Side
PEAK L
It shows that
maximum output
power has been
reached. The
light is on when,
for any reasons,
distortion on the
Left power
outputs is higher
than 1% THD.
Left OUTPUT
CLAMPS
INPUTS
L / R
Left and Right
inputs of the
amplifier.
Signal to be
applied to the
input must be
both balanced
and
unbalanced.
When
connection is
unbalanced,
please use
normal PIN-
RCA. When
connection is
balanced,
please use
audison cable
PIN-ABS.
Right OUTPUT
CLAMPS
MONO
Outputs for
bridge mono
configuration.
To be used
when the
amplifier is
selected in
MONO IN R
configuration
through the
switch put on
the upper part
of the device.
INPUTS
INDICATORS LIGHTS
PEAK R
It shows that
maximum output
power has been
reached. The light is
on when, for any
reasons, distortion on
the Right power
outputs is higher than
1% THD.
SPEAKER R
Right power
outputs of the
amplifier. Connect
loudspeakers
according to
indicated
polarities.
MONO
Outputs for
bridge mono
configuratio.
To be used when
the amplifier is
selected in
MONO IN R
configuration
through the
switch put on the
upper part of the
device.
SPEAKER L
Left power
outputs of the
amplifier.
Connect
loudspeakers
according to
indicated
polarities.
INDICATORS
LIGHTS
ON
Lit when the
amplifier is on.
SAFE
When lit, it indicates
the intervention of
protection circuits: in
case of overheating
(temperature
exceeding 80° C /
176° F) or output
anomalies (presence
of continuous
current, short circuit,
or dangerously low
load impedance).
When protection
circuits intervene,
the amplifier shuts
down. Turn the
amplifier off. When
the problem is
corrected, turn the
amplifier back on.
Car power amplifier
OWNER'S MANUAL
HV 214
A/B: Input levels.
C: Only with balanced
connection, it allows to
connect (ON) or disconnect
(OFF) the input ground.
With unbalanced
connection, the switch
must be put on ON.
D: On ON, it allows the
bridge mono connection,
by using IN R input.
On OFF, the amplifier
works as stereo.
mono
Speaker L
Speaker R
mono
ABS Balanced Inputs
Right
Left
on
peak L
safe
peak R
Input GND
Mono
- in
R
on
off
off (A)
on (B)
Levels
Right
Levels
Left
STEREO
Left
Levels
Input GND
Mono
- in
R
on
off
off
on
0.3 V 4.0 V
SUPPLY
VOLTAGE
HV 2
11 15 VDC
Right
A
B
D
C
PWM
Power
Supply
2.2 KOhms
10 Ohms
GND
HV 214
V
O
L
T
S
36
36
To Chassis
in out in out
Mute Remote Power
R
L
R
PHASE
-180°
L
PREAMPLIFIER
A
B
C
D
CONTROLS
PIN RCA
1-2-3 Balanced connection (PIN ABS)
1-3 Unbalanced connection (PIN RCA)
PIN ABS
B
A
BRIDGE (MONO)
GND
+
GND
+
2
3
1
+
GND
Amplifiers
TECHNICAL DATA
POWER SUPPLY 11 ÷ 15 VDC
IDLING CURRENT 2 A
MAX CONSUMPTION (Nominal Pwr) 40 A
CONT. NOMINAL POWER (Tol. +10%; -5%)
2 ch x 4 Ohms; 0.3% THD; 12 VDC 140 W (RMS)
CONTINOUS POWER (2 ch x 4 Ohms; 13.8 VDC) 145 W (RMS)
CONTINOUS POWER (2 ch x 2 Ohms; 13.8 VDC) 250 W (RMS)
CONTINOUS POWER (4 Ohms; 13.8 VDC)Bridge 500 W (RMS)
TRI-MODE CONNECTION (4 Ohms) 145+145+500 W (RMS-pulse)
DISTORTION THD (1 KHz; 90% Nominal Pwr) 0.04 %
BANDWIDTH (-3 dB; Nominal Pwr) 4 Hz ÷ 100 KHz
DAMPING FACTOR (4 Ohms) 60
RISE TIME 4 µS
SIGNAL / NOISE RATIO 102 dBA
UNBALANCED INPUT SENSITIVITY 0.3 V ÷ 4 VRMS
BALANCED INPUT SENSITIVITY ±0.15 V ÷ ±2 VRMS
INPUT IMPEDANCE 15 KOhms
LOAD IMPEDANCE Stereo 8; 4; 2 Ohms
LOAD IMPEDANCE Mono 8; 4 Ohms
REMOTE IN 3 ÷ 15 VDC
REMOTE OUT 12 VDC - 250 mA
MUTE IN 3 ÷ 15 VDC / GND
MUTE OUT 12 VDC - 5 mA
INPUT GROUND (Selectable for balanced input) ON - OFF
DIMENSIONS (WxHxD) 256 x 61 x 370 mm (10.07 x 2.40 x 14.56)
SERVICE CONNECTIONS
UNIT FIXING
L
ef
t
L
e
v
e
ls
I
n
pu
t GN
D
M
o
n
o
- in
R
on
o
ff
off
o
n
0.3 V 4
.0 V
SUP
P
LY
V
O
LTAG
E
H
V
2
1
1
15
VDC
R
ig
ht
mono
Speaker L
Speaker R
mono
ABS Balanced Inputs
Right
Left
on
peak L
safe
peak R
CONTROLS
in out in out
Mute Remote Power
A
20
FUSE 30 A
+ BATTERY
10 cm (4 inch) MAX
GROUND
mono
Speaker L
Speaker R
mono
ABS Balanced Inputs
Right
Left
on
peak L
safe
peak R
SPEAKERS SPEAKERS
in out in out
Mute Remote Power
CONNECTIONS AND FUNCTIONS
Rear Side
MUTE
IN
Mute control coming from radio-cassette player (or any
source provided with output for the amplifier mute).
It is especially made to be connected to the mute output
of a cellular telephone in order to silence the amplifier
for incoming calls, and it allows to reactivate musical
reproduction at the end of phone conversation.
It can be connected to the MUTE OUT output of a
preceding amplifier to allow the simultaneous silencing
of all amplifiers connected in cascade.
Applied voltage must be between 3 and 15 VDC or
connect to GND.
OUT
Output for the other amplifiers in the sound system.
It must be connected to the MUTE IN of the successive
amplifier to allow the simultaneous silencing of all
amplifiers connected in cascade.
The available voltage on this output is 12 VDC with
current equal to 5 mA.
POWER
Input clamps for the
amplifier power
supply.
Connect the battery
positive and negati-
ve according to
indicated polarities.
Applied voltage
mest be between 11
and 15 VDC.
POWER SUPPLY
CLAMPS
REMOTE
IN
Turn on control for the
amplifier, coming from
radio-cassette player (or
from any sources
provided with remote
control for amplifiers).
Applied voltage must be
between 3 and 15 VDC.
OUT
Output leading to other amplifiers of
the sound system. It has to be connected
to the REMOTE IN of the successive
amplifier to allow the simultaneous
turning on of the whole system. The
available voltage on this output is 12
VDC with a current equal to 250 mA.
MUTE AND REMOTE MASTER SLAVE CONNECTION
REMOTE OUT
MUTE OUT
R
E
M
O
T
E
I
N
MUTE IN
RADIO / CD PLAYER
M
U
T
E
I
N
REMOTE
REMOTE IN
MOBILE
CAR PHONE
AUX
MASTER AMPLIFIER SECOND AMPLIFIER
MUTE OUT
REMOTE OUT
TO OTHER AMPLIFIERS
in out in out
Mute Remote Power
in out in out
Mute Remote Power
/
