Moen 6997A Owner's manual

Moen
Brand
Moen
Model
6997A
Category
Sanitary ware
Type
Owner's manual

This manual is also suitable for

MB107C
INSTALLATION INSTRUCTIONS
MODE D'INSTALLATION
Before turning water on during either rough-in or trim-out, make sure that cartridge retainer nuts are in place. The cartridge and retainer nuts were
properly installed and tested before leaving the factory. Although it is unlikely, it is nevertheless possible that through the handling of the valve by
any number of persons the retainer nuts may not be properly installed. This should be carefully checked at time of rough-in and trim-out. If the retainer
nuts are not properly installed, water pressure could force the cartridge out of the casting. Personal injury or water damage to the premises could
result.
Avant d’ouvrir l’alimentation en eau, soit pendant la pose de la plomberie brute ou pendant la pose de la garniture, s’assurer que la bague de retenue
est en place.La cartouche et la bague de retenue de cartouche ont ete correctement installee et testes avant de quitter l'usine. Quoiqu'improbable,
il est neanmoins possible que par suite de la manipulation de la valve par plusieurs personnes, la bague de rentenue ait ete deplacee. Ceci devra
etre soigneusement verifie lors de la pose de la plomberie brute et lors de la pose la garniture. Si la bague de retenue n'est pas correctement installee,
la pression d'eau pourrait deloger le cartouche du bati de robinet. Ceci pourrait causer des blessures corporelles ou des degats par l'eau sur les lieux.
CAUTION:
REMARQUE:
FERMER l’alimentation en eau avant de démonter la soupape. Ouvrir les deux poignée de la soupape pour
libérer la pression d’eau et s’assurer que la pression d’eau est COMPLETEMENT coupée.
Always turn water off before disassembling the valve. Open valve handle to relieve water pressure and to
insure that complete water shut-off has been accomplished.
8" MIN.
CENTERS
ENTR'AXES DE 8" MIN.
1-1/2"
2-3/4" 2-3/4"
CONCENTRIX
HANDLE
(INSERTS NOT INCLUDED)
POIGNEE CONCENTRIX
(INSEREE PAS FOURNI)
TRADITIONAL
CROSS HANDLE
(INSERTS NOT INCLUDED)
POIGNEE CROIX
TRADITIONAL
(INSEREES PAS FOURNI)
TRADITIONAL
LEVER HANDLE
(INSERTS NOT INCLUDED)
POIGNEE LEVIER
TRADITIONAL
(INSEREES PAS FOURNI)
(ACRYLIC INSERT)
(INSEREE ACRYLIQUE
ACRYLIC KNOB
HANDLE
POIGNEE
ACRYLIQUE
BALL
HANDLE
POIGNEE
DE BAL
TOP OF
FINISHED
SURFACE
HAUT DE
SURFACE FINI
®
Open trim package and check to see that all parts for the tub filler installation have been enclosed:
2 compression nuts
2 O-rings
2 handle adapters
1 spout
1 spout escutcheon
1 spout plug button
1. With a pipe cutter or hacksaw, cut the mounting shank to required height (1-5/8" to 1-3/4") above finished deck.
CAUTION: REMOVE BURRS AND BEVEL END OF SHANK. FAILURE TO DO SO MAY RESULT IN DAMAGED SPOUT O-RING
DURING SPOUT INSTALLATION.
2. Install set screw into tub spout.
3. Apply 3/8" bead of plumbers putty (not furnished) around the base of the escutcheon.
4. Install roll pin into base of tub spout. CAUTION: SEE TEMPLATE ON PAGE 4 FOR ROLL PIN LOCATION. Drill a 7/32" hole into
tub base. Install tub spout with roll pin installed onto mounting shank. Press down until it becomes properly located with top spout
escutcheon. ON MODELS WITH SPOUT ESCUTCHEON, INSTALL SPOUT ESCUTCHEON BEFORE TUB SPOUT AND USE LONG
ROLL PIN, ON OTHER MODELS USE SHORT ROLL PIN.
5. With the tub spout and roll pin in position, tighten set screw with hex wrench and install plug button.
Ouvrir l'emballage de la garniture et vérifier si toutes les pièces requises pour l'installation du bec verseur sont incluses:
2 ecrou de compression 1 vis de pression
2 anneau en "O" 2 vis de poignée
2 adaptateurs de poignée 1 ou 2 chevilles cylindrique
1 bec 2 trousse de poigée
1 rosace de bec 1 regleur de rosace
1 bouchon de bec
1. Avec un coupe-tuyaux, couper la tige de montage a la hauteur desirée. REMARQUE: ENLEVER LES EBARBURES ET BISEAUTER
L'EXTREMITE DE LA TIGE. CETTE OPERATION EMPECHERA D'ENDOMMAGE L'ANNEAU EN "O" LORS DE L'INSTALLATION
DU BEC.
2. Installer la vis de pression à l'intérieur du bec.
3. Appliquer un collier de 3/8 po. de mastic de plombier (non-inclus) autour la base de la rosace.
4. Installer la cheville cylindrique à l'intérfieur de la base du bec de baignoire. REMARQUE: VOIR GABARIT A LA PAGE 4 POUR
L'EMPLACEMENT DE LA CHEVILLE CYLINDRIQUE. Percer un trou de 7/32 po. dans la base de la baignoire. Installer le bec de
baignoire avec la cheville cylindrique sur la tige de montage. Presser jusqu'à ce que le bec soit de niveau avec la base de la baignoire.
5. En maintenant le bec de baignoire et la cheville cylindrique en position, visser la vis de pression avec une clé hexagonale et installer
bouchon de bec.
O-RING
ANNEAU EN "O"
SET
SCREW
VIS DE
PRESSION
MOUNTING
SHANK
TIGE DE
MONTAGE
TOP OF
FINISHED SURFACE
HAUT DE SURFACE FINI
PUTTY
(NOT SUPPLIED)
MASTIC
(PAS FOURNI)
SPOUT ESCUTCHEON
ROSACE DE BEC
ROLL PIN
CHEVILLE CYLINDRIQUE
1-3/8" TO 1-5/8"
PLUG
BUTTON
BOUCHON
DE BEC
ESCUTCHEON ADJUSTER
REGLEUR DE ROSACE
Tub Spout Installation
1 spout set screw
2 handle screws
1 or 2 roll pins (1 short, 1 long)
2 handle assemblies
1 escutcheon adapter
MB107C
1-5/8" - 1-3/4"
TOP OF FINISHED SURFACE
HAUT DE SURFACE FINI
Page is loading ...
(FRONT)
(DEVANT)
HELPLINE: Call our toll free Helpline number,
in the U.S. (800) 321-6636; in Canada - Toronto, 905-829-3400; other provinces,
(800) 465-6130; for answers to any product, installation, replacement parts, or
warranty questions.
APPELER SANS FRAIS M. CONSEIL®:
Téléphone à notre LIGNE D'AIDE de 8.30 à 16.30 HNE, afin d'obtenir les résponses
à n'importe quelle question au sujet du produit, de pieces de rechange, de
l'installation ou de la garantie.
en la E.U., (800) 321-6636; in Canada - Toronto, 905-829-3400; Autres provinces,
(800) 465-6130. Demandez le service au produit.
TEMPLATE FOR ROLL PIN LOCATION
GARBARIT POUR L'EMPLACEMENT DE LA CHEVILLE
CYLINDRIQUE
MB107C SEPT 94
25300 Al Moen Drive, North Olmsted, OH. 44070-8022
2816 Bristol Circle , Oakville, Ontario L4W 1H7 Canada
© Copyright, 1994
Moen Incorporated
Printed in U.S.A.
➤
➤
➤
➤
.730
27/32" DIA.
MOUNTING SHANK
DIAMETRE DE LA TIGE
DE MONTAGE 27/32 PO.
7/32"
DRILLROLL PIN
PERCER UN TROU DE 7/32
PO. POUR LA CHEVILLE
CYLINDRIQUE
®
Flushing-Rinçage
IMPORTANT: Pipe chips, sand, stones and other solids found in new and renovated plumbing can damage the sealing surfaces of the cartridge and
cause a leak. To avoid damage, DO NOT TURN ON SUPPLY VALVES until instructed below.
1. After installing and connecting your new faucet, open both hot and cold cartridges.
2. Turn on both hot and cold water supply valves and allow the water to run for 15 seconds.
3. Turn off the water. Unscrew stream straightener from spout and remove any trapped debris.
4. Replace the stream straightener. Check system for leaks.
IMPORTANT: Les débris de tuyauterie, le sable, la pierraille et autres matériaux qui se trouvent dans la plomberie neuve et rénovée peut endommager
les surfaces d'éntanchéité de la cartouche et causer une fuite. Pour éliminer ces risques, NE PAS FAIRE FONCTIONNER LA SOUPAPE avant d'avoir
complété ces instructions.
1. Apres avoir installé et raccordé votre nouveau robinet. Ouvrir les cartouches.
2. Ouvrir les soupapes d'arrêt et laisse s'écouler pendant 15 secondes.
3. Couper l'eau. Dévisser l'adapteur du bec et retirer tous les débris de tuyauterie.
4. Replacer l'aérateur. Vérifier si le système a des fuites.
TO INSTALL VALVE BODIES
1. Turn valve mounting nuts all the way down on valve bodies
for tub base clearance. Drop one mounting washer on each
side.
2. Slide valve bodies up through mounting holes and fasten front
above temporarily with top locknut. Slide washer on spout
shank under retaining ring and put shank through center hole
of deck. Install bracket and mounting hardware.
3. Measure supply tubes on valve bodies to connecting tee (not
furnished). Measure tube (not furnished) from tee to spout
shank. Cut them to suit.
4. With valve bodies, tee, and spout tube assembled and proper-
ly aligned, hand tighten and solder where required.
5. Make final tightening of valve bodies and spout shank from
below.
6. Connect supply lines with 1/2" copper fittings (not furnished).
7. Install a test plug (not furnished) in spout shank.
8. Test installation for leaks.
9. Remove test plug from spout shank and proceed to install
trim.
GENERAL INFORMATION
NOTE: When top of valve body is flush with top
mounting nut, valve body outlet ports will be 3-
1/2" below deck. Valve top locknuts and spout
retaining ring washer are to be on the same
plane.
LOCKNUT DIA. 1-5/8"
ESCUTCHEON DIA. 1-7/8" or 2-1/2"
VALVE BODY DIA. 1-1/8"
SPOUT SHANK DIA. 27/32"
VALVE BODY LOWER
MOUNTING WASHER DIA. 1-3/4"
SPOUT SHANK TOP
MOUNTING WASHER DIA. 1-5/8"
ROUGH-IN INSTALLATION DIRECTIONS
Before turning water on, during either rough-in or trim out, make sure that cartridge retainer nuts are in place. The cartridge and cartridge
retainer nuts were properly installed and tested before leaving the factory. Although it is unlikely, it is nevertheless possible that through the
handling of the faucet by any number of persons the cartridge retainer nuts may not be properly installed. This should be carefully checked
at time of rough-in and trim-out. If the cartridge retainer nuts are not properly installed, water pressure could force the cartridge out of the
faucet body. Personal injury or water damage to the premises could result.
CAUTION: Always turn water OFF before disassembling faucet. Open faucet handles to alleviate water pressure to insure that
COMPLETE water shut-off has been accomplished.
MT335F
SCREW
STEM
EXTENSION
ESCUTCHEON
ADJUSTER
CARTRIDGE
RETAINER NUT
1248
CARTRIDGE
TOP
LOCKNUT
BOTTOM
VALVE
MOUNTING
WASHER
BOTTOM
VALVE BODY
MOUNTING NUT
SPOUT
COVER
TUBE
THREADED
FOR TEST PLUG
SPOUT
SHANK
RETAINING
RING
WASHER
BRACKET
LOCKNUT
1/2" COPPER TUBE
(NOT FURNISHED)
1-1/4" FOR STANDARD
INSTALLATION
SCREW
(SELF-TAPPING)
TEE
(NOT FURNISHED)
VALVE
COVER
TUBE
3-1/2"
4-5/8"
MODEL 4999
®
HI FLOW WIDESPREAD ROMAN TUB
TOP OF
FINISHED SURFACE
LOCKNUT
FULLY
ENGAGED
WASHER
BRACKET
*3/8"
MAX
1/4" TO 1-1/2"
MAX BASE
1-1/4" MAX
3/4" MIN
3-1/2"
PROTECTIVE
PAPER
COVER TUBE
THIN DECK
INSTALLATION
THICK DECK
INSTALLATION
*3/8" Max. dimension shown is the
maximum height of valve body to
allow for supply tube "T" to
spout shank connection.
TUBE LENGTH TO MAKE
A 10" MAX CENTERSET
TOP OF
FINISHED SURFACE
MT335F JAN '92
®
MOEN INCORPORATED, 377 WOODLAND AVE., ELYRIA, OH. 44035, U.S.A.
TO DISASSEMBLE VALVE:
CAUTION: SHUT OFF HOT AND COLD WATER SUPPLIES AND OPEN FAUCET HANDLES TO ALLEVIATE WATER PRESSURE AND INSURE THAT
COMPLETE WATER SHUT-OFF HAS BEEN ACCOMPLISHED.
1. Remove stem extension, screw, and stem extension.
2. Remove escutcheon adjuster.
3. Using cartridge removal tool (not supplied), unscrew and remove cartridge retainer.
4. Replace stem extension and screw. Grasp stem extension, being careful not to damage threads, pull straight upward removing cartridge.
SCREW
STEM
EXTENSION
ESCUTCHEON
ADJUSTER
CARTRIDGE
RETAINER NUT
1248
CARTRIDGE
TOP
LOCKNUT
CARTRIDGE
REMOVAL
TOOL
HELPLINE: Call our toll free Helpline number:
for answers to any product, installation, replacement
parts, or warranty questions.
(800) 321-6636
© Copyright, 1992
Moen Incorporated
Printed in U.S.A.
TO ASSEMBLE VALVE:
1. Drop stem extension with cartridge attached into valve body, press down until it bot-
toms.
2. Slowly rotate stem extension clockwise while still pressing down. This will align the
"KEY" on the cartridge with the "NOTCH" in the valve body. When the key enters the
notch you will feel it drop in, then the cartridge will be in place. To be certain, rotate
the stem extension clockwise and then counterclockwise. You should feel the car-
tridge stop in both directions. If so, the cartridge is in place. Do not turn on water yet.
3. Using a cartridge removal tool (not supplied), reinstall cartridge retainer nut until it bot-
toms (DO NOT CROSS THREAD).
4. Reinstall escutcheon adjuster.
You are now ready to turn on the water. Check complete system for leaks.
CAUTION: FAILURE TO FOLLOW THESE INSTRUCTIONS CAN
CAUSE A FAULTY INSTALLATION OR DAMAGE THE NEW CARTRIDGE.
STEM
KEY
NOTCH IN
BODY
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6

Moen 6997A Owner's manual

Moen
Brand
Moen
Model
6997A
Category
Sanitary ware
Type
Owner's manual
This manual is also suitable for
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

in other languages

Related papers

Other documents