Christie 135-005106-01 User manual

FHD462-X LCD Panel

User Manual

020-000769-02

NOTICES

COPYRIGHT AND TRADEMARKS

All brand names and product names are trademarks, registered trademarks or trade names of their respective holders.

GENERAL

Every effort has been made to ensure accuracy, however in some cases changes in the products or availability could occur which may not be reflected in this

document. Christie reserves the right to make changes to specifications at any time without notice. Performance specifications are typical, but may vary

depending on conditions beyond Christie's control such as maintenance of the product in proper working conditions. Performance specifications are based

on information available at the time of printing. Christie makes no warranty of any kind with regard to this material, including, but not limited to, implied

warranties of fitness for a particular purpose. Christie will not be liable for errors contained herein or for incidental or consequential damages in connection

with the performance or use of this material. Canadian manufacturing facility is ISO 9001 and 14001 certified.

WARRANTY

Products are warranted under Christie’s standard limited warranty, the complete details of which are available by contacting your Christie dealer or Christie.

In addition to the other limitations that may be specified in Christie’s standard limited warranty and, to the extent relevant or applicable to your product, the

warranty does not cover:

a. Problems or damage occurring during shipment, in either direction.

b. Projector lamps (See Christie’s separate lamp program policy).

c. Problems or damage caused by use of a projector lamp beyond the recommended lamp life, or use of a lamp other than a Christie lamp supplied by

Christie or an authorized distributor of Christie lamps.

d. Problems or damage caused by combination of a product with non-Christie equipment, such as distribution systems, cameras, DVD players, etc., or

use of a product with any non-Christie interface device.

e. Problems or damage caused by the use of any lamp, replacement part or component purchased or obtained from an unauthorized distributor of

Christie lamps, replacement parts or components including, without limitation, any distributor offering Christie lamps, replacement parts or

components through the internet (confirmation of authorized distributors may be obtained from Christie).

f. Problems or damage caused by misuse, improper power source, accident, fire, flood, lightening, earthquake or other natural disaster.

g. Problems or damage caused by improper installation/alignment, or by equipment modification, if by other than Christie service personnel or a Christie

authorized repair service provider.

h. Problems or damage caused by use of a product on a motion platform or other movable device where such product has not been designed, modified

or approved by Christie for such use.

i. Problems or damage caused by use of a projector in the presence of an oil-based fog machine or laser-based lighting that is unrelated to the projector.

j. For LCD projectors, the warranty period specified in the warranty applies only where the LCD projector is in “normal use” which means the LCD

projector is not used more than 8 hours a day, 5 days a week.

k. Except where the product is designed for outdoor use, problems or damage caused by use of the product outdoors unless such product is protected

from precipitation or other adverse weather or environmental conditions and the ambient temperature is within the recommended ambient

temperature set forth in the specifications for such product.

l. Image retention on LCD flat panels.

m.Defects caused by normal wear and tear or otherwise due to normal aging of a product.

The warranty does not apply to any product where the serial number has been removed or obliterated. The warranty also does not apply to any product

sold by a reseller to an end user outside of the country where the reseller is located unless (i) Christie has an office in the country where the end user is

located or (ii) the required international warranty fee has been paid.

The warranty does not obligate Christie to provide any on site warranty service at the product site location.

PREVENTATIVE MAINTENANCE

Preventative maintenance is an important part of the continued and proper operation of your product. Please see the Maintenance section for specific

maintenance items as they relate to your product. Failure to perform maintenance as required, and in accordance with the maintenance schedule specified

by Christie, will void the warranty.

REGULATORY

The product has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed

to provide reasonable protection against harmful interference when the product is operated in a commercial environment. The product generates, uses, and

can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio

communications. Operation of the product in a residential area is likely to cause harmful interference in which case the user will be required to correct the

interference at the user’s own expense.

CAN ICES-3 (A) / NMB-3 (A)

이 기기는 업무용 (A 급)으로 전자파적합등록을 한 기기이오니 판매자 또는 사용자는 이점을 주의하시기 바라며 , 가정 외의 지역에서 사용하는 것을 목적

으로 합니다 .

Environmental

Theproductisdesignedandmanufacturedwithhigh‐qualitymaterialsandcomponentsthatcanberecycledandreused.This symbol meansthatelectricaland

electronicequipment,attheirend‐of‐life,shouldbedisposedofseparatelyfromregularwaste.Pleasedisposeoftheproductappropriatelyandaccordingtolocal

regulations.IntheEuropeanUnion,thereareseparatecollectionsystemsforusedelectricalandelectronicproducts.Pleasehelpustoconservetheenvironmentwe

livein!

FHD462-X LCD Panel User Manual 3

020-000769-02 Rev. 1 (01-2016)

Content

Package Handling . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

Unpacking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6

Handling and Care . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6

Cleaning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6

Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

Key Features and Benefits . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7

Parts List . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7

Controls and Functions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

Display at a Glance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9

Input Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11

Remote Control Unit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .13

Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

Remote Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .15

Notes on Batteries . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .15

Notes on Remote Control Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .15

Locking and Unlocking the Remote Control . . . . . . . . . . . . . . . . . . . . . . . . . . .16

Quick Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .16

Installation Considerations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .17

Handling Guidelines . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .17

Ambient Heat . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .17

Ventilation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .18

Mounting the Display . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .18

Connections to the Display . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .18

Connecting a Control System or PC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .19

IR Extender Connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .20

Connecting Source Components to the Display . . . . . . . . . . . . . . . . . . . . . . . . .21

Setting Up a Video Wall . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .22

Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25

Turning on the Power . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .25

Changing the OSD Language . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .25

Avoiding Image Retention . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .26

Using the On-Screen Menus . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .27

FHD462-X LCD Panel User Manual 4

020-000769-02 Rev. 1 (01-2016)

Image Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .30

Display Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .35

Audio Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .36

Basic Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .37

Advanced Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .39

Factory Reset . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .43

System Status . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .44

Using the Picture-in-Picture (PIP) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .44

Using the Display in Low Light Environments . . . . . . . . . . . . . . . . . . . . . . . . . . . .46

Maintenance and Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48

Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .48

Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .48

External Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50

RS232 and Ethernet Communications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .50

RS232 Connection and Port Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . .50

Command and Response Format . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .50

Command and Response Examples . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .51

Serial Command List . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .52

Power control and input sources . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .52

Display adjustment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .53

Other controls . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .55

Using Video Wall Toolbox . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .59

Using Discrete IR Codes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .64

IR Command Protocol . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .64

IR Control Code List . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .65

Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 66

Display Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .66

Supported Timings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .68

Overall Dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .70

FHD462-X LCD Panel User Manual 5

020-000769-02 Rev. 1 (01-2016)

Package Handling

Danger! Failure to comply with the

following results in death or serious

injury.

• Do not drop the panel (even a short

distance), or apply pressure to the

sides of the bezel. The small size of

the bezel, which enables minimal

image-to-image gaps, means there is

reduced protection of the LCD glass

and components. Dropping the panel

or applying unnecessary force to the

sides of the bezel will result in

permanent damage.

• To avoid serious injury and/or serious

damage to the LCD panel, moving the

panel requires at least two people.

Hold the white handles on the

shipping package when moving/

shipping.

• Extreme care must be taken when

pushing the mounted display into its

locked position. Always handle the

display on the opposing corners of the

frame to avoid direct contact with the

LCD glass.

Notice. Failure to comply with the following may result in property damage.

• Due to the delicate nature of the display, we strongly recommend that you use the provided

packing materials and secure the package onto a pallet during shipment.

Package Handling

FHD462-X LCD Panel User Manual 6

020-000769-02 Rev. 1 (01-2016)

Unpacking

Each LCD panel is packed inside a box carton. To protect the panel during transportation, additional

packing material has been placed within the carton.

1. Before unpacking, prepare a stable, level and clean surface near a wall outlet for your LCD

panel.

2. Set the box in an upright position and pull out the white carton locks.

3. Lift up the top cover carton.

4. Remove the ESD bag before removing the display from the bottom tray carton.

Handling and Care

To avoid damaging your LCD panel, follow these guidelines when

handling or moving the panel:

• Always use the handles on the back of the LCD panel. Do not

hold onto the frame when transporting.

• Two people are required when moving or raising the LCD

panel. Use both hands, one positioned on the top handle and

the other on the bottom handle.

• Hold and support the LCD panel at each side and keep at an

even height above the ground.

• Do not twist or bend the panel.

• Use a cart to move several panels at one time.

• When the panel is sitting on a surface, do not tilt it more than

10° to avoid damaging the screen.

Cleaning

Use a cloth dampened with water or methyl alcohol to clean the screen surface. We recommend

that you keep the protective plastic sheet shipped with the panel to replace it each time the panels

are packed and shipped.

Warning! Failure to comply with the following could result in death or serious injury.

• Make sure the power connector and any other cables are unplugged before moving the product.

Failure to comply could result in minor or moderate injury.

Notice. Failure to comply with the following may result in property damage.

• Unplug the power cord before cleaning the LCD panel. Do not use a liquid, spray cleaners, or any

abrasive cleaners to clean the LCD panel. Failure to comply may result in equipment damage.

FHD462-X LCD Panel User Manual 7

020-000769-02 Rev. 1 (01-2016)

Introduction

The FHD462-X LCD Panel is a cutting-edge direct-view LCD that, when tiled with multiple units, can

create enormous images in multiple configurations. The display combines a simple and slim design

with unparalleled image quality with configurable I/O to provide a perfect building block for large-

format video walls, which are ideal in digital signage and control-room applications.

Key Features and Benefits

The display offers these key features and benefits:

• Full-HD Native Resolution: 1920 x 1080 (16:9 Native Aspect Ratio)

• High Brightness: Up to 500 nits

• 178-degree Viewing Angle

• DisplayPort 1.2a, HDMI 1.4 and DVI Inputs with High-bandwidth Digital Content Protection

(HDCP)

• DisplayPort 1.2 input and output to support daisy-chaining 4 displays using Multi-Stream

Transport (MST)*

• Allows 4K content on a 2x2 video wall for sources that support Multi-Stream Transport (MST)*

• Video Signal Looping

• Direct LED Backlight

• Video Wall Toolbox software [included] simplifies setting up a large video wall, with up to 100

displays, using a Windows PC

• Portrait- and Landscape-Mode Compatible

Parts List

Your display is shipped with the following items. If any items are missing or damaged, please

contact your dealer.

• FHD462-X LCD Panel

• Remote Control Unit and batteries

• AC Power cord

•DVI Cable

• RS232 Communications Cable

• RS485 Communications Cable

Introduction

FHD462-X LCD Panel User Manual 8

020-000769-02 Rev. 1 (01-2016)

•IR Extender Cable

• Video Wall ToolBox Installation CD1

1.* M u l t i - S t rea m Tr a n sp ort (MS T) r equ ire s u s in g a v id eo c ard t ha t s u ppo r ts t h i s f ea t u r e a n d D i s-

playPort 1.2. Contact your dealer for more details on how to use MST.

FHD462-X LCD Panel User Manual 9

020-000769-02 Rev. 1 (01-2016)

Controls and Functions

Display at a Glance

The illustration below shows the key display components, and the paragraphs that follow describe

them.

1. HANDLES

Always use the handles when carrying the display. DO NOT touch or hold the screen face.

2. MAIN POWER SWITCH

Connects or disconnects the display panel from the AC power source.

3. STATUS LED

Lights orange to indicate that the display is in standby mode; blinks orange if no input signal is

present; off if the main power switch is set to off.

11

1

2

4

3

Controls and Functions

FHD462-X LCD Panel User Manual 10

020-000769-02 Rev. 1 (01-2016)

4. KEYPAD

You can use the keypad instead of the remote control unit to operate the

on-screen display (OSD) controls. The keypad operates as follows:



On/Standby ( )



Press once to toggle from standby mode to on mode. Press it again to

return to standby mode. 



SOURCE

To select a source, press the SOURCE button repeatedly (with no menus

visible on-screen). 



When a menu is visible on-screen, this button operates identically to the

right-arrow (or ENTER) button on the display remote control unit. 



When a menu is visible on-screen, this button operates identically to the

left-arrow button on the display remote control unit.



/ 

When a menu is visible on-screen, these buttons operate identically to the

up- and down-arrow buttons on the display remote control unit.



MENU/EXIT

Press this button to access the on-screen display (OSD) controls, or to exit

the current menu and return to the previous one.

SOURCE

MENU/EXIT

Controls and Functions

FHD462-X LCD Panel User Manual 11

020-000769-02 Rev. 1 (01-2016)

Input Panel

The illustration below shows the display input panel.

1. Power Input (100 to 240 VAC)

Connect the display to power here.

2. RS485 Out

A female, 8-pin RJ-45 connector that connects to the next display in a video wall.

3. RS485 In

A female, 8-pin RJ-45 connector that connects to the next video source.

4. RS232 In

A female, 9-pin D-sub connector for interfacing with a PC or home theater automation/control

system.

5. LAN

An RJ-45 connector for connecting to Ethernet via a Cat 5 cable.

1

2

3

4

5

6

7

8

9

10

11

12

13

14

15

16

17

Controls and Functions

FHD462-X LCD Panel User Manual 12

020-000769-02 Rev. 1 (01-2016)

6. DisplayPort Out

DisplayPort 1.2 and HDCP-compliant digital video output for connecting the display to the next

display in a video wall.

7. IR Receiver

An IR sensor that sends information of an infrared remote control to another device by

receiving and decoding signals.

8. VGA Out (15-pin D-sub) 

VESA-standard analog video output for connecting the display to the next display in a video

wall.

9. DVI 1 In (HDCP-compliant)

VESA-standard digital video input for connecting DVI sources.

10. DVI 1 Out (HDCP-compliant)

VESA-standard digital video output for connecting the display to the next display in a video

wall.

11. DisplayPort In

DisplayPort 1.2 and HDCP-compliant digital video input for connecting DisplayPort sources.

12. HDMI 1, 2

Two (2) HDCP-compliant digital video inputs for connecting HDMI or DVI sources.

13. DVI 2 In (HDCP-compliant)

VESA-standard digital video input from a personal computer, or digital video from a DVD player

or HD set-top box.

14. VGA In (15-pin D-sub)

VESA-standard analog video input for connecting a personal computer or other analog video

source.

15. Audio In

For connecting an external audio device, such as a player, audio mixer or microphone.

16. IR Extender

Connect the IR Extender cable provided with the display to this input.

17. Audio Out

For connecting external, powered speakers or an external audio receiver/amplifier.

Controls and Functions

FHD462-X LCD Panel User Manual 13

020-000769-02 Rev. 1 (01-2016)

Remote Control Unit

The illustration below shows the display remote control, and the table that follows describes its

functionality.

2

4

6

1

3

5

9

7

10

8

Controls and Functions

FHD462-X LCD Panel User Manual 14

020-000769-02 Rev. 1 (01-2016)

Label Description

1 Turns the monitor on and off

2 INFO Provides source and resolution information

3 VGA Selects the VGA source

DVI Selects the DVI source 1

HDMI1 Selects the HDMI source 1

DVI-2/AV Selects the DVI source 2

HDMI2 Selects the HDMI source 2

4 P-POSITION Selects the PIP position

DISPLAYPORT Select the DisplayPort source

PIP Turns the PIP feature on and off

5 P-SOURCE Selects the secondary sub-source

6 SWAP Swaps the main and PIP source

7 MENU Opens the monitor’s on-screen menu system. When the menu system is already

open, pressing this button will select the previous submenu

, , , Navigates through submenus and settings

8 ENTER Selects highlighted menu choices

9 EXIT Closes the menu system

10 SCALING Selects each aspect ratio, in sequence: Full Screen, Native, Letter Box and Pillar Box

FREEZE Freezes the current source image

MUTE Turns off the sound

BRIGHT Adjusts the brightness

CONTRAST Adjusts the contrast

AUTO Auto adjustment of VGA source

SOURCE Selects each source, in sequence

VOLUME- Decreases the sound volume

VOLUME+ Increases the sound volume

FHD462-X LCD Panel User Manual 15

020-000769-02 Rev. 1 (01-2016)

Installation

Remote Control

To install batteries in the remote control:

1. Press down the tab on the cover and pull the cover up.

2. Insert the included batteries. Ensure that the polarities correctly match the and markings

inside the battery compartment.

3. Insert the lower tab of the cover into the opening, and press down the cover until it clicks in

place.

Notes on Batteries

• Make sure that the battery polarities are correct when installing the batteries.

• Do not mix an old battery with a new one or different types of batteries.

• If you will not use the remote control for a long time, remove the batteries to avoid damage

from battery leakage.

• Do not expose batteries to excessive heat such as from sunshine, fire or the like.

Notes on Remote Control Operation

• Make sure that there is nothing obstructing the infrared beam between the remote control and

the IR receiver on the display.

• If the effective range of the remote control decreases, or it stops working, replace the batteries

with new ones.

• The remote control may fail to operate if the infrared remote sensor is exposed to bright

sunlight or fluorescent lighting.

• Ambient conditions may possibly impede the operation of the remote control. If this happens,

point the remote control at the display, and repeat the operation.

Notice. Failure to comply with the following may result in property damage.

• Installation must be performed by a qualified custom video installation specialist.

Installation

FHD462-X LCD Panel User Manual 16

020-000769-02 Rev. 1 (01-2016)

Locking and Unlocking the Remote Control

You can lock the remote control buttons to prevent unauthorized persons from changing settings on

the display. To do this, press ENTER, ENTER, EXIT, EXIT, ENTER and EXIT, in sequence. To

unlock a locked remote control unit, use the same sequence of button presses.

Quick Setup

Here is a quick overview of the display installation process. The sections following this one provide

detailed instructions.

Step Procedure For Details, Refer to

page...

1 Mount the display(s) on a wall (optional) 18

2 Connect other external equipment to the display (optional):

• Automation/control system (RS232 or Ethernet)

• IR extender 19

20

3 Connect signal sources to the display 21

4 For video wall installations, connect video cables and control cables to each

display in a series (optional)

5 Apply power to the display 25

6 Change the OSD language (optional) 25

7 Display calibration: adjust the following for each input:

• Aspect ratio • Color level

• Brightness • Tint

• Contrast • Input position

• Color temperature and white balance

30

Installation

FHD462-X LCD Panel User Manual 17

020-000769-02 Rev. 1 (01-2016)

Installation Considerations

Proper installation of your display will ensure a satisfying viewing experience. Whether you are

installing a display temporarily or permanently, you should take the following into account to ensure

your display performs optimally.

Handling Guidelines

Narrow bezel displays such as the FHD462-X are inherently very fragile devices. To avoid damaging

your LCD panel, follow these guidelines when handling or moving the panel. Please note that

damage due to improper handling is not covered under warranty.

• Always use the handles on the back of the LCD panel. Do not hold the display by its edges

(outer bezel).

• Two people are required when moving or raising the LCD panel. Use both hands, one positioned

on the top handle and the other on the bottom handle.

• Do not twist or bend the panel.

• Hold and support the LCD panel at each side and keep at an even height above the ground.

• Use a cart to move multiple panels at one time.

• When the panel is sitting on a surface, do not tilt it more than 10° to avoid damaging the

screen.

Ambient Heat

Keep the ambient temperature constant and below 40°C (104°F). Keep the display away from

heating and/or air conditioning vents.

Installation

FHD462-X LCD Panel User Manual 18

020-000769-02 Rev. 1 (01-2016)

Ventilation

If you are mounting the display in an enclosure, leave sufficient space on all sides between it and

surrounding objects, as shown below. This allows heat to disperse, maintaining the proper

operating temperature. For very thin installations, to mount the display close to a wall it may be

necessary to remove the handles prior to installation.

Mounting the Display

You can mount the display on a wall.

If you do decide to wall-mount the display, ensure that the wall-mount bracket is installed

according to the instructions included with it. The wall must be capable of supporting a redundant

weight factor three (3) times the weight of the display, or be reinforced.

We recommend that this be done by a custom installation specialist.

Connections to the Display

Proceed as follows to connect the display to your video sources, external controller(s) – if present –

and AC power.

When connecting your equipment:

• Turn off all equipment before making any connections.

• Use the correct signal cables for each source.

Notice. Failure to comply with the following may result in property damage.

• Use only the approved wall-mount kit designed for your display.

Wall

15 mm

(0.59

"

)

Installation

FHD462-X LCD Panel User Manual 19

020-000769-02 Rev. 1 (01-2016)

• For best performance and to minimize cable clutter, use high-quality cables that are only as

long as necessary to connect two devices. (Don’t use a 20-foot cable when a 6-foot cable will

suffice.)

• Ensure that the cables are securely connected. Tighten the thumbscrews on connectors that

have them.

Connecting a Control System or PC

RS232 Connection

Use a straight-through RS232 cable with a 9-pin male connector to connect a PC or control/

automation system (if present) to the RS232 port on the display.

For more information about using this connection, refer to External Control on page 50.

to Automation/

Control System

or PC

2 Receive Data

(to ctrl. system)

3 Transmit Data

(from ctrl. system)

5 Ground

1

2

345

7

89 6

Installation

FHD462-X LCD Panel User Manual 20

020-000769-02 Rev. 1 (01-2016)

Ethernet Connection

Use a standard Ethernet cable with an RJ45 male connector to connect a PC or control/automation

system (if present) to the Ethernet port on the display.

For more information about using this connection, refer to External Control on page 50.

IR Extender Connection

Connect the provided IR extender cable to the IR Extender input as shown below.

to Ethernet Hub,

Router or Gateway

8

1

6 Receive Data -

3 Receive Data +

2 Transmit Data -

1 Transmit Data +

(3.5-mm, mini

phono plug)

Remote Control

Page is loading ...

Christie 135-005106-01, FHD462-X User manual

Related papers

Other documents