2. Ranger design
  3. 19-U0002

Ranger design 19-U0002 Installation guide

  • Hello! I am an AI chatbot trained to assist you with the Ranger design 19-U0002 Installation guide. I’ve already reviewed the document and can help you find the information you need or explain it in simple terms. Just ask your questions, and providing more details will help me assist you more effectively!
INSTALLATION GUIDE
19-U0002 Access Stow Double Rack Kit
Scan the QR for the latest Install-Guide.
For technical support, contact us at 1-800-565-5321 19-U0002 Installation Guide | REV. A5 | Page 2 of 9
READ, UNDERSTAND, AND FOLLOW ALL WARNINGS AND INSTRUCTIONS BEFORE USING THIS PRODUCT.
FAILURE TO FOLLOW THESE DIRECTIONS MAY RESULT IN PROPERTY DAMAGE, SERIOUS BODILY INJURY,
AND/OR DEATH. RANGER DESIGN IS NOT RESPONSIBLE FOR ANY PROPERTY DAMAGE, PERSONAL INJURY,
OR DEATH THAT OCCURRED WHILE USING ANY RANGER DESIGN PRODUCTS.
• Failure to use Ranger Design-provided fasteners, brackets, and proper installation guidelines could increase risk
of serious personal injury and/or death.
• If drilling is required to complete this installaon: improper drilling can cause property damage to vehicles and could lead to
electric shock, re, or even death.
• If drilling is required to complete this installaon: Ensure that drilling is only performed on areas of the vehicle allowed by the
vehicle's Original Equipment Manufacturer’s Body Builders Layout Book (or equivalent document).
• Prior to installaon, inspect the vehicle to ensure that installaon will not interfere with, or cause obstrucon of, any crical
components such as electrical wiring, fuel tanks, fuel-cells, locks, latches, etc.
• The installer or manufacturer is responsible for ensuring anchorages are installed onto suitable wall and oor structures; wall
and oor strength must meet applicable performance requirements.
• Do not install systems into any weak or unsound materials such as plascs, woods, thin-walled metals, etc. without proper
reinforcement.
• Do not install this product where it could interfere with the deployment of airbags. Failure to comply could result in death or
serious injury.
• Do not install this product where it could ingress on the Transit Occupant Protecon Zone. Failure to comply could result in
death or serious injury.
• Incorrect installaon could cause water leaks, electric shock or re.
• Any cargo vehicle with any cargo or equipment should use a cered paron. See Ranger Design website for some paron
opons. (hps://rangerdesign.com/)
• Mounngs rails are recommended for any aachment to the vehicle walls.
• All items in the cargo area should be properly secured and paron doors closed while the vehicle is in moon.
• Check your vehicle’s tare weight and remaining load capacity with all the equipment installed. Never exceed the maximum
Gross Vehicle Weight Rang (GVWR), Gross Axle Weight Rangs (GAWRs), or other maximum loads permied by the vehicle's
Original Equipment Manufacturer (OEM) and required by law.
• The heaviest items must be placed towards the bottom of the vehicle, while the lightest ones can be arranged u p w a r d s .
Vehicle cargo loading weight proporon should follow the following guidelines:
• The nal alterer and/ or modier should review the warning sheet with the customer before the vehicle is released to the
customer or for general use. These instrucons should remain with the vehicles a all mes.
• Any modicaon or unintended use of this product voids any warranty and could create a hazardous condion.
• Ranger Design provides recommended assembly and installaon instrucons which should be followed to ensure
correct operaon. Failure to do so could result in invalidang the product’s compliance, warranty and cause injury.
Notwithstanding, the nal stage vehicle alterer and/or modier is responsible for the integraon, installaon, and
compliance of the product in its nal locaon to all applicable regulaons and standards. Failure to maintain compliance
of the vehicle to applicable regulaons and standards could be punishable by law. Alterers and/or modiers should consult
with all local authories prior to commissioning.
• Drilling is required to complete this installaon. Before drilling, ensure that you will not hit any crical parts of the vehicle
like the gas tank, wiring harness, or hose. Consult the vehicle OEM documentaon as necessary. When drilling, use a drill
collar to reduce the risk of damage to the vehicle.
• Any materials, padding, or glazing installed in the vehicle must comply with FMVSS/CMVSS 201/205/302, as applicable.
• In the event of a motor vehicle accident or collision where a Ranger system has been installed, especially ones where the
vehicle structure is damaged and/or the air bags deploy and/or the vehicle has been towed, the system must be inspected
to ensure connued soundness and safety before returning the vehicle to service. Damaged components should be
replaced as necessary.
• All system components should be regularly inspected, cleaned, and maintained pursuant to Ranger guidelines.
WARNING
BEFORE YOU BEGIN
CAUTION
For technical support, contact us at 1-800-565-5321 19-U0002 Installation Guide | REV. A5 | Page 3 of 9
PHASE 1 – ASSEMBLY
1.1 SETUP
1.1.2 Verify all parts are present.
19-U0002 BOX
Middle Strap left Middle Strap right
Side Stopper ×4
Stopper Saddle ×4
extruSion (double) ×3 C braCket ×6
Rear Strap ×2
Saddle, double ×3 Ladder Support Plate ×2
Anti Theft LoCk x2Anti Theft Hook x2 anti theft handle x2
For technical support, contact us at 1-800-565-5321 19-U0002 Installation Guide | REV. A5 | Page 4 of 9
REQUIRED ITEMS
HARDWARE
2
PERSONS
( M8 ) ×22
( M8 ) ×8
Small
CAP ×8
MS231 ×22( M8 ) ×52( M8 × 25 ) ×32( M8 ) ×12
( M6 ) ×4
13mm ×1
For technical support, contact us at 1-800-565-5321 19-U0002 Installation Guide | REV. A5 | Page 5 of 9
PHASE 1 – ASSEMBLY
1.2 MECHANISM
STEP 1
A B
Attach middle strap in the mechanism.
1
2
1
2
Slide ×4 Slide ×2
For technical support, contact us at 1-800-565-5321 19-U0002 Installation Guide | REV. A5 | Page 6 of 9
×2
STEP 2
Attach rear strap and extrusion in the mechanism.
11.5"
10"
For technical support, contact us at 1-800-565-5321 19-U0002 Installation Guide | REV. A5 | Page 7 of 9
PHASE 2 – INSTALLATION
1.2 MECHANISM INSTALLATION
STEP 1 STEP 2
×6 each side
use lock nut
rubber washer
rubber pad
Slide 6 bolts in each side. Lift the mechanism on top of the crossbars.
WARNING: Extrusion should not pass
outside the mirror
STEP 2
Attach the mechanism to the crossbar.
For technical support, contact us at 1-800-565-5321 19-U0002 Installation Guide | REV. A5 | Page 8 of 9
Optimum adjustment & setup Guide
The Access Stow setup is inuenced and effected by the following physical factors:
1. Ladder weight
2. Ladder Height
3. Quantity of ladder ( i.e 1 or 2 ladders, if applicable )
To provide optimum performance of your ladder lift assistance & drop down, there is
a degree of adjustment to aid the weight & length of your ladder type.
These two form of adjustment are provided by:
1. The gas ram 'gas spring' hole position.
2. The centre Access Stow extrusion drop height.
ACCESS STOW SETUP
There are 5 different settings to suit the
weight on the system.
! Please refer to the picture (F4 & F5) to aid the optimum setting and
safe ladder weight and sizes which can be accommodated.
Gasram 'gas spring' can be adjsuted.
For technical support, contact us at 1-800-565-5321 19-U0002 Installation Guide | REV. A5 | Page 9 of 9
Medium RAM Promaster & medium roof ford transit
Sprinter, hiGh roof ram promastertransit hiGh roof & nissan nV
F4
F5
“You have successfully assembled your
19-U0002 kit and Installed your Access Stow
Thank you for doing business with us.”
For any feedback or suggestions you may have, please contact: cs@rangerdesign.com
/