User Manual
7PZ IP
9/20 Ver. 1.05
ADJ Products, LLC - www.adj.com - 7ZP IP - User Manual Page 2
©2021 ADJ Products, LLC all rights reserved. Information, specications, diagrams, images, and
instructions herein are subject to change without notice. ADJ Products, LLC logo and identifying
product names and numbers herein are trademarks of ADJ Products, LLC. Copyright protection
claimed includes all forms and matters of copyrightable materials and information now allowed
by statutory or judicial law or hereinafter granted. Product names used in this document may be
trademarks or registered trademarks of their respective companies and are hereby acknowledged. All
non-ADJ Products, LLC brands and product names are trademarks or registered trademarks of their
respective companies.
ADJ Products, LLC and all aliated companies hereby disclaim any and all liabilities for property,
equipment, building, and electrical damages, injuries to any persons, and direct or indirect economic
loss associated with the use or reliance of any information contained within this document, and/or as
a result of the improper, unsafe, insucient and negligent assembly, installation, rigging, and operation
of this product.
ADJ PRODUCTS LLC World Headquarters
6122 S. Eastern Ave. | Los Angeles, CA 90040 USA
Tel: 800-322-6337 | Fax: 323-582-2941 | www.adj.com |[email protected]
ADJ Supply Europe B.V.
Junostraat 2 | 6468 EW Kerkrade | Netherlands
Tel: +31 45 546 85 00 | Fax: +31 45 546 85 99 | www.americandj.eu | [email protected]
Europe Energy Saving Notice
Energy Saving Matters (EuP 2009/125/EC)
Saving electric energy is a key to help protecting the environment. Please turn off all electrical products when
they are not in use. To avoid power consumption in idle mode, disconnect all electrical equipment from power
when not in use. Thank you!
DOCUMENT VERSION
Due to additional product features and/or enhancements, an updated version of
this document may be available online.
Please check www.adj.com for the latest revision/update of this manual
before beginning installation and/or programming.
Date Document
Version
Software
Version DMX Channel Mode Notes
9/07/20 1.0 N/A N/A Initial Release
01/27/21 1.05 N/A N/A Updated Software
ADJ Products, LLC - www.adj.com - 7ZP IP - User Manual Page 3
UNPACKING
Thank you for purchasing the 7PZ IP by ADJ Products, LLC. Every 7PZ IP has been thoroughly tested and has
been shipped in perfect operating condition. Carefully check the shipping carton for damage that may have
occurred during shipping. If the carton appears to be damaged, carefully inspect your fixture for any damage
and be sure all accessories necessary to operate the unit has arrived intact. In the case damage has been
found or parts are missing, please contact our toll free customer support number for further instructions. Do not
return this unit to your dealer without first contacting customer support.
INTRODUCTION
The 7PZ IP is an IP65 outdoor rated, DMX intelligent, zooming, LED par fixture with ADJ’s WiFly TransCeiver
with wireless DMX built-in. This fixture can be used in a stand alone mode or connected in a Primary/Secondary
configuration. This wash has seven operating modes: 6Color Change mode, 30 Color Change mode, Auto Fade
mode, Auto Run Mode, Manual Mode, Static Color Mode, and DMX Control Mode.
FEATURES
• Multi-Colors
• Electronic Dimming 0-100%
• 5-45 Degree Beam Angle
• DMX-512 protocol
• 3-Pin & 5-Pin DMX Connections
• 12 DMX Channel Modes
• Built-In ADJ’s WiFly EXR Wireless DMX Up to 2,500 feet/760M•
• IP65 Locking 3/5-Pin XLR Connector In/Out
• IP65 Locking Power Connector In/Out
• Power Cord Daisy Chain
Included Accessories:
• 1 x IP65 Locking Power Cable
• 1 x Scissor Yoke
CUSTOMER SUPPORT
ADJ® provides a customer support line, to provide set up help and to answer any questions that may arise during
your set up or initial operation. You may also visit us on the web at www.adj.com for any comments or suggestions.
For service related issues please contact ADJ.
ADJ SERVICE USA - Monday - Friday 8:00am to 4:30pm PST
Voice: 800-322-6337 Fax: 323-532-2941 E-mail: [email protected]
ADJ GROUP SERVICE EUROPE - Monday - Friday 08:30 to 17:00 CET
Voice: +31 45 546 85 30 Fax: +31 45 546 85 96 E-mail: [email protected]
WARRANTY REGISTRATION
Please complete and mail in the enclosed warranty card to validate your purchase. All returned service
items, whether under warranty or not, must be freight pre-paid and accompany a return authorization (R.A.)
number. The R.A. number must be clearly written on the outside of the return package. A brief description of
the problem as well as the R.A. number must also be written down on a piece of paper and included in the
shipping container. If the unit is under warranty, you must provide a copy of your proof of purchase invoice.
Items returned without an R.A. number clearly marked on the outside of the package will be refused and
returned at customer’s expense. You may obtain an R.A. number by contacting customer support.
IMPORTANT NOTICE!
THERE ARE NO USER SERVICEABLE PARTS INSIDE THIS DEVICE. DO NOT ATTEMPT ANY REPAIRS
YOURSELF; DOING SO WILL VOID THE WARRANTY. DAMAGES RESULTING FROM MODIFICATIONS
TO THIS DEVICE AND/OR THE DISREGARD OF SAFETY AND OPERATION INSTRUCTIONS IN
THIS USER MANUAL VOIDS THE MANUFACTURER’S WARRANTY AND IS NOT SUBJECT TO ANY
WARRANTY CLAIMS AND/OR REPAIRS.
7PZ IP General Information
ADJ Products, LLC - www.adj.com - 7ZP IP - User Manual Page 4
7PZ IP Safety Guidelines
• Do not position device close to any FLAMMABLE MATERIALS while operating
• Do not expose this unit rain or moisture.
• Do not spill water or other liquids into or on to your unit.
• Do not attempt to operate this unit if the power cord has been frayed or broken.
• Do not attempt to remove or break off the ground prong from the electrical cord. This prong is used
to reduce the risk of electrical shock and re in case of an internal short.
• Disconnect from main power before making any type of connection.
• Do not remove the cover under any conditions. There are no user serviceable parts inside.
• Never operate this unit when it’s cover is removed.
• Never plug this unit in to a dimmer pack.
• Always be sure to mount this unit in an area that will allow proper ventilation. Allow about 6” (15cm)
between this device and a wall.
• Do not attempt to operate this unit, if it becomes damaged.
• Do not use of this product outdoors voids all warranties. his unit is intended for indoor use only.
• Disconnect mains power to the unit during long periods of non-use.
• Always mount this unit in safe and stable matter.
• Always route power-supply cords so that they are not likely to be walked on or pinched by items
placed upon or against them, paying particular attention to the point they exit from the unit.
• Cleaning -The xture should be cleaned only as recommended by the manufacturer.
• Heat - The appliance should be situated away from heat sources such as radiators, heat registers,
stoves, or other appliances (including ampliers) that produce heat.
• The xture should be serviced by qualied service personnel when:
A. The power-supply cord or the plug has been damaged.
B. Objects have fallen, or liquid has been spilled into the appliance.
C. The appliance has been exposed to rain or water.
D. The appliance does not appear to operate normally or exhibits amarked change in performance.
ESD CAUTION: This unit, like any wireless electronic device is highly susceptible to ESD,
electrostatic discharge. ESD can severely damage the unit.
ADJ Products, LLC - www.adj.com - 7ZP IP - User Manual Page 5
7PZ IP IP Notice
IP65 RATED
An IP rated lighting xture, which is commonly installed in outdoor environments, has been designed
with an enclosure that effectively protects the ingress (entry) of external foreign objects such as dust
and water. The International Protection (IP) rating system is commonly expressed as "IP" (Ingress
Protection) followed by two numbers (i.e. IP65), where the numbers dene the degree of protection.
The rst digit (Foreign Bodies Protection) indicates the extent of protection against particles entering
the xture, and the second digit (Water Protection) indicates the extent of protection against water
entering the xture. An IP65 rated lighting xture is one, which has been designed and tested to protect
against the ingress of dust (6) and low-pressure water jets from any direction (5).
MARINE / COASTAL ENVIRONMENT INSTALLATIONS!
Please note although this xture is IP rated, the xture is NOT suitable for marine and/or coastal
environment installations. Installing this xture in a marine and/or coastal environment may
cause corrosion and/or excessive wear to the interior and/or exterior components of the xture.
Damages and/or performance issues resulting from installation in a marine and/or coastal
environment will void the manufactures warranty and will NOT be subject to any warranty claims
and/or repairs.
Ensure ALL connections and end caps are properly sealed with a non-conductive dielectric grease
(available at most electrical suppliers) to prevent water ingress/condensation and/or corrosion.
OPTIONAL CORROSION - RESISTANT COATING Optional Corrosion-Resistant
Coatings may be available for this xture. Please consult your ADJ Products, LLC sales
representative for details.
ADJ Products, LLC - www.adj.com - 7ZP IP - User Manual Page 6
7PZ IP Protective Vent
ADJ Products, LLC - www.adj.com - 7ZP IP - User Manual Page 7
7PZ IP Set Up
Power Supply: The ADJ 7PZ IP contains an automatic voltage switch, which will auto sense the voltage
when it is plugged into the power source. With this switch there is no need to worry about the correct
power voltage, this unit can be plugged in anywhere.
DMX-512: DMX is short for Digital Multiplex. This is a universal protocol used as a form of communication
between intelligent xtures and controllers. A DMX controller sends DMX data instructions from the
controller to the xture. DMX data is sent as serial data that travels from xture to xture via the DATA
“IN” and DATA “OUT” XLR terminals located on all DMX xtures (most controllers only have a DATA
“OUT” terminal).
DMX Linking: DMX is a language allowing all makes and models of different manufactures to be
linked together and operate from a single controller, as long as all xtures and the controller are DMX
compliant. To ensure proper DMX data transmission, when using several DMX xtures try to use the
shortest cable path possible. The order in which xtures are connected in a DMX line does not inuence
the DMX addressing. For example; a xture assigned a DMX address of 1 may be placed anywhere in
a DMX line, at the beginning, at the end, or anywhere in the middle. When a xture is assigned a DMX
address of 1, the DMX controller knows to send DATA assigned to address 1 to that unit, no matter
where it is located in the DMX chain.
Data Cable (DMX Cable) Requirements (For DMX Operation): The 7PZ IP can be controlled via
DMX-512 protocol. Your unit and your DMX controller requires either a 3-pin or 5-pin XLR connector
for data input and data output. We recommend Accu-Cable DMX cables. If you are making your own
cables, be sure to use standard 110-120 Ohm shielded cable (This cable may be purchased at almost
all pro lighting stores). Your cables should be made with a male and female XLR connector on either
end of the cable. Also remember that DMX cable must be daisy chained and cannot be split.
TO MAINTAIN IP65 RATING INTEGRITY AND PREVENT WATER FROM ENTERING THE FIXTURE,
ALL UNUSED CONNECTION RUBBER CAPS MUST BE SEALED AND ONLY IP65 RATED POWER
AND DATE CABLES MUST BE USED.
ADJ Products, LLC - www.adj.com - 7ZP IP - User Manual Page 8
7PZ IP Set Up
Special Note: Line Termination. When longer runs of cable are used, you may need to use a
terminator on the last unit to avoid erratic behavior. A terminator is a 110-120 ohm 1/4 watt resistor
which is connected between pins 2 and 3 of a male XLR connector (DATA + and DATA -). This unit is
inserted in the female XLR connector of the last unit in your daisy chain to terminate the line. Using a
cable terminator (ADJ part number Z-DMX/T) will decrease the possibilities of erratic behavior.
Termination reduces signal errors and avoids signal transmission problems
and interference. It is always advisable to connect a DMX terminal, (Resistance
120 Ohm 1/4 W) between PIN 2 (DMX-) and PIN 3 (DMX +) of the last xture.
5-Pin XLR DMX Connectors. Some manufactures use 5-pin DMX- 512 data cables for DATA
transmission in place of 3-pin. 5-pin DMX xtures may be implemented in a 3-pin DMX line. When
inserting standard 5-pin data cables in to a 3-pin line a cable adaptor must be used, these adaptors are
readily available at most electric stores. The chart below details a proper cable conversion.
3-Pin XLR to 5-Pin XLR Conversion
Conductor Ground/
Shield
3-Pin XLR Female
(Out) 5-Pin XLR Male (In)
Ground/Shield Pin 1 Pin 1
Data Compliment (-
signal) Pin 2 Pin 2
Data True (+ signal) Pin 3 Pin 3
Not Used Do Not Use
Not Used Do Not Use
ADJ Products, LLC - www.adj.com - 7ZP IP - User Manual Page 9
Channel Value Function
1 0 - 255 HUE: 0 - 100%
2 0 - 255 SATURATION: 0 - 100%
30 - 255 INTENSITY: 0 - 100%
4 0 - 255 ZOOM: NARROW - WIDE
Channel Value Function
1 0 - 255 RED: 0 - 100%
2 0 - 255 GREEN: 0 - 100%
30 - 255 BLUE: 0 - 100%
4 0 - 255 WHITE: 0 - 100%
5 0 - 255 ZOOM: NARROW - WIDE
7PZ IP 4 Channel - HSI
7PZ IP 5 Channel - RGBW
Channel Value Function
1 0 - 255 HUE: 0 - 100%
2 0 - 255 SATURATION: 0 - 100%
30 - 255 INTENSITY: 0 - 100%
4 0 - 255 ZOOM: NARROW - WIDE
5
0 - 20
21 - 40
41 - 60
61 - 80
81 - 100
101-255
DIMMER CURVES:
STANDARD
STAGE
TV
ARCHITECTURAL
THEATRE
DEFAULT TO UNIT CURVE SETTING
7PZ IP 5 Channel - HSI + Zoom
Channel Value Function
1 0 - 255 RED: 0 - 100%
2 0 - 255 GREEN: 0 - 100%
30 - 255 BLUE: 0 - 100%
4 0 - 255 WHITE: 0 - 100%
5 0 - 255 MASTER DIMMER: 0 - 100%
6 0 - 255 ZOOM: NARROW - WIDE
7PZ IP 6 Channel - RGBW + Zoom
ADJ Products, LLC - www.adj.com - 7ZP IP - User Manual Page 10
7PZ IP 7 Channel - sRGBWI
Channel Value Function
10 - 255 RED: 0 - 100%
20 - 255 GREEN: 0 - 100%
30 - 255 BLUE: 0 - 100%
40 - 255 WHITE: 0 - 100%
50 - 255 MASTER DIMMER: 0 - 100%
60 - 255 MASTER DIMMER (FINE): 0 - 100%
70 - 255 ZOOM: NARROW - WIDE
7PZ IP 7 Channel - RGBW
Channel Value Function
1 0 - 255 RED: 0 - 100%
2 0 - 255 GREEN: 0 - 100%
3 0 - 255 BLUE: 0 - 100%
4 0 - 255 WHITE: 0 - 100%
5
0 - 31
32 - 63
64 - 95
96 - 127
128 - 159
160 - 191
192 - 223
224 - 255
SHUTTER/STROBE
LED OFF
LED ON
STROBING SLOW - FAST
LED ON
STROBE PULSE SLOW - FAST
LED ON
RANDOM STROBE SLOW - FAST
LED ON
6 0 - 255 MASTER DIMMER: 0 - 100%
7 0 - 255 MASTER DIMMER (FINE): 0 - 100%
8 0 - 255 ZOOM: NARROW - WIDE
7PZ IP 8 Channel - RGBW
Channel Value Function
1
0 - 31
32 - 63
64 - 95
96 - 127
128 - 159
160 - 191
192 - 223
224 - 255
SHUTTER/STROBE
LED OFF
LED ON
STROBING SLOW - FAST
LED ON
STROBE PULSE SLOW - FAST
LED ON
RANDOM STROBE SLOW - FAST
LED ON
2 0 - 255 RED: 0 - 100%
3 0 - 255 GREEN: 0 - 100%
4 0 - 255 BLUE: 0 - 100%
5 0 - 255 WHITE: 0 - 100%
6 0 - 255 INTENSITY: 0 - 100%
7 0 - 255 ZOOM: NARROW - WIDE
ADJ Products, LLC - www.adj.com - 7ZP IP - User Manual Page 11
Channel Value Function
1 0 - 255 RED: 0 - 100%
2 0 - 255 GREEN: 0 - 100%
30 - 255 BLUE: 0 - 100%
4 0 - 255 WHITE: 0 - 100%
5
0 - 31
32 - 63
64 - 95
96 - 127
128 - 159
160 - 191
192 - 223
224 - 255
SHUTTER/STROBE
LED OFF
LED ON
STROBING SLOW - FAST
LED ON
STROBE PULSE SLOW - FAST
LED ON
RANDOM STROBE SLOW - FAST
LED ON
60 - 255 MASTER DIMMER: 0 - 100%
7 0 - 255 MASTER DIMMER (FINE): 0 - 100%
8 0 - 255 ZOOM: NARROW - WIDE
9
0 - 20
21 - 40
41 - 60
61 - 80
81 - 100
101-255
DIMMER CURVES:
STANDARD
STAGE
TV
ARCHITECTURAL
THEATRE
DEFAULT TO UNIT CURVE SETTING
7PZ IP 9 Channel - RGBW
Channel Value Function
1 0 - 255 RED: 0 - 100%
2 0 - 255 RED (FINE): 0 - 100%
30 - 255 GREEN: 0 - 100%
4 0 - 255 GREEN (FINE): 0 - 100%
5 0 - 255 BLUE: 0 - 100%
6 0 - 255 BLUE (FINE): 0 - 100%
7 0 - 255 WHITE: 0 - 100%
8 0 - 255 WHITE (FINE): 0 - 100%
9 0 - 255 ZOOM: NARROW - WIDE
10 0 - 255 ZOOM (FINE): NARROW - WIDE
7PZ IP 10 Channel - RGBW 16-Bit
ADJ Products, LLC - www.adj.com - 7ZP IP - User Manual Page 12
7PZ IP 10 Channel - HSI
Channel Value Function
1
0 - 31
32 - 63
64 - 95
96 - 127
128 - 159
160 - 191
192 - 223
224 - 255
SHUTTER/STROBE
LED OFF
LED ON
STROBING SLOW - FAST
LED ON
STROBE PULSE SLOW - FAST
LED ON
RANDOM STROBE SLOW - FAST
LED ON
20 - 255 HUE: 0 - 100%
30 - 255 SATURATION: 0 - 100%
40 - 255 INTENSITY: 0 - 100%
50 - 255 COLOR MACROS (See page 22, Color Macro Chart)
60 - 255 ZOOM: NARROW - WIDE
7
1 - 20
21 - 40
41 - 60
61 - 80
81 - 100
101 - 120
121 - 140
141 - 160
161 - 180
181 - 200
201 - 220
221 - 240
241 - 250
251 - 255
AUTO PROGRAMS
PROGRAM 1
PROGRAM 2
PROGRAM 3
PROGRAM 4
PROGRAM 5
PROGRAM 6
PROGRAM 7
PROGRAM 8
PROGRAM 9
PROGRAM 10
PROGRAM 11
PROGRAM 12
PROGRAM 13
GRADIENT EFFECT
8AUTO PROGRAMS SPEED: SLOW - FAST
9AUTO PROGRAMS FADE: SLOW - FAST
10
0 - 20
21 - 40
41 - 60
61 - 80
81 - 100
101-255
DIMMER CURVES:
STANDARD
STAGE
TV
ARCHITECTURAL
THEATRE
DEFAULT TO UNIT CURVE SETTING
ADJ Products, LLC - www.adj.com - 7ZP IP - User Manual Page 13
7PZ IP 12 Channel - RGBWI
Channel Value Function
1
0 - 31
32 - 63
64 - 95
96 - 127
128 - 159
160 - 191
192 - 223
224 - 255
SHUTTER/STROBE
LED OFF
LED ON
STROBING SLOW - FAST
LED ON
STROBE PULSE SLOW - FAST
LED ON
RANDOM STROBE SLOW - FAST
LED ON
20 - 255 RED: 0 - 100%
30 - 255 GREEN: 0 - 100%
40 - 255 BLUE: 0 - 100%
50 - 255 WHITE: 0 - 100%
60 - 255 INTENSITY: 0 - 100%
70 - 255 COLOR MACROS (See page 22, Color Macro Chart)
80 - 255 ZOOM: NARROW - WIDE
9
1 - 20
21 - 40
41 - 60
61 - 80
81 - 100
101 - 120
121 - 140
141 - 160
161 - 180
181 - 200
201 - 220
221 - 240
241 - 250
251 - 255
AUTO PROGRAMS
PROGRAM 1
PROGRAM 2
PROGRAM 3
PROGRAM 4
PROGRAM 5
PROGRAM 6
PROGRAM 7
PROGRAM 8
PROGRAM 9
PROGRAM 10
PROGRAM 11
PROGRAM 12
PROGRAM 13
GRADIENT EFFECT
10 0 - 255 AUTO PROGRAMS SPEED: SLOW - FAST
11 0 - 255 AUTO PROGRAMS FADE: SLOW - FAST
12
0 - 20
21 - 40
41 - 60
61 - 80
81 - 100
101-255
DIMMER CURVES:
STANDARD
STAGE
TV
ARCHITECTURAL
THEATRE
DEFAULT TO UNIT CURVE SETTING
ADJ Products, LLC - www.adj.com - 7ZP IP - User Manual Page 14
7PZ IP 13 Channel - RGBW
Channel Value Function
1 0 - 255 RED: 0 - 100%
2 0 - 255 GREEN: 0 - 100%
30 - 255 BLUE: 0 - 100%
4 0 - 255 WHITE: 0 - 100%
5 0 - 255 COLOR MACROS (See page 22, Color Macro Chart)
6
0 - 31
32 - 63
64 - 95
96 - 127
128 - 159
160 - 191
192 - 223
224 - 255
SHUTTER/STROBE
LED OFF
LED ON
STROBING SLOW - FAST
LED ON
STROBE PULSE SLOW - FAST
LED ON
RANDOM STROBE SLOW - FAST
LED ON
70 - 255 MASTER DIMMER: 0 - 100%
80 - 255 MASTER DIMMER (FINE): 0 - 100%
90 - 255 ZOOM: NARROW - WIDE
10
1 - 20
21 - 40
41 - 60
61 - 80
81 - 100
101 - 120
121 - 140
141 - 160
161 - 180
181 - 200
201 - 220
221 - 240
241 - 250
251 - 255
AUTO PROGRAMS
PROGRAM 1
PROGRAM 2
PROGRAM 3
PROGRAM 4
PROGRAM 5
PROGRAM 6
PROGRAM 7
PROGRAM 8
PROGRAM 9
PROGRAM 10
PROGRAM 11
PROGRAM 12
PROGRAM 13
GRADIENT EFFECT
11 0 - 255 AUTO PROGRAMS SPEED: SLOW - FAST
12 0 - 255 AUTO PROGRAMS FADE: SLOW - FAST
13
0 - 20
21 - 40
41 - 60
61 - 80
81 - 100
101-255
DIMMER CURVES:
STANDARD
STAGE
TV
ARCHITECTURAL
THEATRE
DEFAULT TO UNIT CURVE SETTING
ADJ Products, LLC - www.adj.com - 7ZP IP - User Manual Page 15
ZPZ IP Operating Instructions
LED Display On/Off:
To set the LED display to turn off after 60 seconds, press the MODE button until “don” is displayed, press the UP
button to display “doff”. Now the display will disappear after 60s. Press any button to turn the display on again.
Be advised though that the display will turn off automatically after 10 seconds.
To set the display press the MODE button until “dXX” is displayed. Use the UP or DOWN buttons to select either:
“don” = LED display on at all times.
“doFF” = LED display shuts off after 60 seconds.
LED Display Inversion:
Follow these instructions to ip the display 180° so that the display can be read upside down.
1. Plug the xture in and press the MODE button until “dXX” is dis- played. “XX” represents either “on” or “oFF”.
2. Press the SET UP button until “Stnd” or “rev” is displayed. 3. Press the UP or DOWN buttons to reverse the
display 180°.
DMX Mode:
Operating through a DMX controller gives the user the freedom to create their own programs tailored to their
needs. This function also allows the xtures to be used as spotlights. The 7PZ IP has 12 DMX modes.
1. This function will allow you to control each individual xture’s traits with a standard DMX 512 controller.
2. To run your xture in DMX mode, enter the MENU screen by pressing and holding the MODE button. Press
the UP or DOWN buttons until “Menu Set ADDR” is displayed. Press the ENTER button then use the UP
or DOWN buttons to select your desired DMX address. Press ENTER after you have found your desired
address.
3. After you have set your desired DMX address, select your desired DMX channel mode. Access the main
menu and press the UP or DOWN buttons until “Menu UserMode” is displayed.
4. Use the UP or DOWN buttons to scroll through the DMX Channel modes. When you have found your desired
DMX Channel mode press ENTER.
5. Please see pages 9-21 for DMX values and traits.
6. After you have chosen your desired DMX Channel mode plug in the xture via the XLR connections to any
standard DMX controller.
Dimmer Curve Setting:
1. Plug the xture in and access the main menu. Press the UP or DOWN buttons until “Menu Function” is
displayed, and press ENTER.
2. Press the UP or DOWN buttons until “Dim Curve” is displayed, and press ENTER.
3. Press the UP or DOWN buttons to nd your desired dimmer curve. Press ENTER to select and conrm.
Please see the Dimmer Curve Diagram Chart on page 31 to see the settings and their respective beginning
and ending fade times.
Color Balance Mode:
1. Plug the xture in and access the main menu. Press the UP or DOWN buttons until “Menu Function” is
displayed, and press ENTER.
2. Press the UP or DOWN buttons until “Settings WhiteBal” is displayed, and press ENTER. Use the UP or
DOWN buttons to scroll through the RGBW colors. When you nd a color you would like to adjust press
ENTER. Use the UP or DOWN buttons to adjust the color output and press ENTER when done.
3. When you are nished making your adjustments press the MODE button to exit this menu.
ADJ Products, LLC - www.adj.com - 7ZP IP - User Manual Page 16
ZPZ IP Operating Instructions
No DMX Hold:
This mode is used as a precaution mode, that in case the DMX signal is lost, the operating mode chosen in this
setup is the running mode the xture will go into when the DMX signal is lost. You can also set this as the operating
mode you would like the unit to return to when power is applied.
1. Plug the xture in and access the main menu. Press the UP or DOWN buttons until “Menu Function” is
displayed, and press ENTER.
2. Press the UP or DOWN buttons until “No DMX Hold” is displayed, and press ENTER. Use the UP or DOWN
buttons to nd your desired setting.
• “Blackout” - If the DMX signal is lost or interrupted, the unit will automatically go into stand by mode.
• “Hold” (Last State) - If the DMX signal is lost or interrupted, the xture will stay in the last DMX set up. If
power is applied and this mode is set, the unit will automatically go into the last DMX set up.
• “Program” - If the DMX signal is lost or interrupted, the unit will automatically run a built-in program.
3. Find your desired setting and press ENTER. Your setting will be saved automatically.
Zoom:
The zoom function indicated here works with Auto Run mode, Static color mode, 6 Color change mode, 30 Color
change mode, and Auto Fade mode.
1. Plug the xture in and access the main menu. Press the UP or DOWN buttons until “Menu Function” is
displayed, and press ENTER.
2. Press the UP or DOWN buttons until “Zoom” is displayed, and press ENTER.
3. Use the UP or DOWN buttons to adjust the zoom.
4. When you are nished making your adjustment press ENTER and press the MODE button to exit this menu.
Auto Run Mode:
1. Plug the xture in and access the main menu. Press the UP or DOWN buttons until “Menu Function” is
displayed, and press ENTER.
2. Press the UP or DOWN buttons until “Auto Run FQN” is displayed, and press ENTER.
3. Use the UP or DOWN buttons to adjust the Auto Run.
4. When you are nished making your adjustment press ENTER and press the MODE button to exit this menu.
Static Color Mode:
1. Plug the xture in and access the main menu. Press the UP or DOWN buttons until “Menu Function” is
displayed, and press ENTER.
2. Press the UP or DOWN buttons until “Static CL:X” is displayed, and press ENTER.
3. Press ENTER again to adjust the static colors. Use the UP or DOWN buttons to scroll through the colors.
4. When you have found your desired color press ENTER. Your are now in the strobe menu. You can use the UP
or DOWN buttons to adjust the strobe rate. Press ENTER when have nished making your adjustments.
6 Color Change Mode:
1. Plug the xture in and access the main menu. Press the UP or DOWN buttons until “Menu Function” is
displayed, and press ENTER.
2. Press the UP or DOWN buttons until “Static CL:X” is displayed, and press ENTER.
3. Use the UP or DOWN buttons to scroll until “2. Chang6” is displayed. Press ENTER and use the UP or DOWN
buttons to adjust the color change speed.
4. When you have found your desired color change speed press ENTER. Your are now in the strobe menu. You can
use the UP or DOWN buttons to adjust the strobe rate. Press ENTER when have nished making your adjustments.
ADJ Products, LLC - www.adj.com - 7ZP IP - User Manual Page 17
ZPZ IP Operating Instructions
30 Color Change Mode:
1. Plug the xture in and access the main menu. Press the UP or DOWN buttons until “Menu Function” is
displayed, and press ENTER.
2. Press the UP or DOWN buttons until “Static CL:X” is displayed, and press ENTER.
3. Use the UP or DOWN buttons to scroll until “Chang30” is displayed. Press ENTER and use the UP or DOWN
buttons to adjust the color change speed.
4. When you have found your desired color change speed press ENTER. Your are now in the strobe menu. You
can use the UP or DOWN buttons to adjust the strobe rate. Press ENTER when have nished making your
adjustments.
Auto Fade Mode:
1. Plug the xture in and access the main menu. Press the UP or DOWN buttons until “Menu Function” is
displayed, and press ENTER.
2. Press the UP or DOWN buttons until “Static CL:X” is displayed, and press ENTER.
3. Use the UP or DOWN buttons to scroll until “4. Fade” is displayed. Press ENTER and use the UP or DOWN
buttons to adjust the color change speed.
4. When you have found your desired color fade speed press ENTER. Your are now in the strobe menu. You
can use the UP or DOWN buttons to adjust the strobe rate. Press ENTER when have nished making your
adjustments.
Color Macros Mode:
1. Plug the xture in and access the main menu. Press the UP or DOWN buttons until “Menu Function” is
displayed, and press ENTER.
2. Press the UP or DOWN buttons until “Macros” is displayed, and press ENTER.
3. Use the UP or DOWN buttons to scoll through the 63 color mac ros.
4. When you have found your desired color Your are now in the Zoom menu. You can use the UP or DOWN
buttons to manually adjust the zoom. Press ENTER when have nished making your adjustments.
Wireless Address:
This function is used to set the wireless address. This address must match the address that is set to WiFly
TransCeiver or WiFly controller.
1. Plug the xture in and access the main menu. Press the UP or DOWN buttons until “Menu Function” is
displayed, and press ENTER.
2. Press the UP or DOWN buttons until “Wireless CH:XX” is displayed. “XX” represents the current displayed address.
Press ENTER to access, and use the UP or DOWN buttons to adjust the wireless channel.
3. When you are nished making your adjustment press ENTER and press the MODE button to exit this menu.
LCD.Set:
This menu is used to adjust the backlight to stay on all the time or turn off after about 5 seconds, set the Key
Lock, and Display Flash.
1. Plug the xture in and access the main menu. Press the UP or DOWN buttons until “Menu Function” is
displayed, and press ENTER.
2. Press the UP or DOWN buttons until “LCD.Set” is displayed. Press ENTER to the menu. Use the UP or
DOWN buttons to make adjustments. Press the ENTER button to scroll between the 3 menus.
3. When you are nished making your adjustment press ENTER and press the MODE button to exit this menu.
ADJ Products, LLC - www.adj.com - 7ZP IP - User Manual Page 18
ZPZ IP Operating Instructions
Default Settings:
When this mode is activated the unit will return to their default settings.
1. Plug the xture in and access the main menu. Press the UP or DOWN buttons until “Menu Function” is
displayed, and press ENTER.
2. Press the UP or DOWN buttons until “DFSET” is displayed, and press ENTER.
3. Use UP or DOWN buttons to switch between “ON/OFF.” If you would like the default setting highlight “ON”
and press ENTER. Press the MODE button to exit.
Temperature C/F:
With this function, you can change the temperature display to show either Celsius or Fahrenheit.
1. Press the MODE button to access the main menu. Press the UP or DOWN buttons so that “Menu Function”
is highlighted, then press ENTER.
2. Press UP or DOWN buttons, until “Temp” is displayed, and press ENTER.
3. Either “Celsius” or “Fahrenheit” will be displayed, use the UP and DOWN buttons to switch between.
4. Press ENTER to conrm your selection or press MODE to exit.
WiFLY On/Off:
This function is used to turn the WiFly function on and off.
1. Plug the xture in and access the main menu. Press the UP or DOWN buttons until “Menu Function” is
displayed, and press ENTER.
2. Press the UP or DOWN buttons until “Wireless” is displayed. Press ENTER to access, and use the UP or
DOWN buttons to switch between “ON” (wireless activated) or “OFF” (wireless deactivated).
3. Press ENTER to conrm your selection and press the MODE button to exit this menu.
Current Running Time:
1. Press the MODE button to access the main menu. Press the UP or DOWN buttons so that “Menu Info” is
highlighted, then press ENTER.
2. Press the UP or DOWN buttons, until “Info TimeInfo” is displayed, and press ENTER.
3. Press the UP or DOWN buttons, until “TimeInfo Current” is displayed, and press ENTER.
4. The current running time will now be displayed, press MODE to exit.
Total Running Time:
1. Press the MODE button to access the main menu. Press the UP or DOWN buttons so that “Menu Info” is
highlighted, then press ENTER.
2. Press the UP or DOWN buttons, until “Info TimeInfo” is displayed, and press ENTER.
3. Press the UP or DOWN buttons, until “TimeInfo TotalTim” is displayed, and press ENTER.
4. The total running time will now be displayed, press MODE to exit.
Last time the current running time was cleared:
1. Press the MODE button to access the main menu. Press the UP or DOWN buttons so that “Menu Info” is
highlighted, then press ENTER.
2. Press the UP or DOWN buttons, until “Info TimeInfo” is displayed, and press ENTER.
3. Press the UP or DOWN buttons, until “TimeInfo LastClea” is displayed, and press ENTER.
4. The the last time the current running time was cleared will now be displayed, press MODE to exit.
ADJ Products, LLC - www.adj.com - 7ZP IP - User Manual Page 19
TimerPin (Clear current Running Time):
In this menu you must input the timer pin to clear the current running time.
1. Press the MODE button to access the main menu. Press the UP or DOWN buttons so that “Menu Info” is
highlighted, then press ENTER.
2. Press the UP or DOWN buttons, until “Info TimeInfo” is displayed, and press ENTER.
3. Press the UP or DOWN buttons, until “TimeInfo TimerPIN” is displayed, and press ENTER.
4. You must now put in the Pin number “050” to clear the current running time.
Current Running Temperature:
1. Press the MODE button to access the main menu. Press the UP or DOWN buttons so that “Menu Info” is
highlighted, then press ENTER.
2. Press the UP or DOWN buttons, until “Info TempInfo” is displayed, and press ENTER.
3. The current running temperature will now be displayed. Press the MODE button to exit.
Model Info:
1. Press the MODE button to access the main menu. Press the UP or DOWN buttons so that “Menu Info” is
highlighted, then press ENTER.
2. Press the UP or DOWN buttons, until “Info Model Inf” is displayed, and press ENTER.
3. The name of the unit will now be displayed, press MODE to exit.
Software Info:
1. Press the MODE button to access the main menu. Press the UP or DOWN buttons so that “Menu Info” is
highlighted, then press ENTER.
2. Press the UP or DOWN buttons, until “Info Software” is displayed, and press ENTER.
3. The software version will now be displayed, press MODE to exit.
Error Info:
1. Press the MODE button to access the main menu. Press the UP or DOWN buttons so that “Menu Info” is
highlighted, then press ENTER.
2. Press the UP or DOWN buttons, until “Info ErrorInf” is displayed, and press ENTER.
3. Any errors that may have occured will be displayed, press MODE to exit.
Zoom Reset:
1. Press the MODE button to access the main menu. Press the UP or DOWN buttons so that “Menu
ZoomRset” is highlighted, then press ENTER.
2. Press the UP or DOWN buttons, until “ZoomRset Reset. M” is displayed, and press ENTER.
3. The display will now show “Reset. M Zoom”. Press ENTER to reset the zoom function.
Zoom Calibration: With this function you can calibrate and adjust the zoom function to its correct
position. The Calibration password 050.
NOTE: ONLY QUALIFIED TECHNICIANS SHOULD PERFORM THIS FUNCTION.
1. Press the MODE button to access the main menu. Press the UP or DOWN buttons so that “Menu
ZoomRset” is highlighted, then press ENTER.
2. Press the UP or DOWN buttons, until “ZoomRset Calibrat” is displayed, and press ENTER.
3. The display will now show the current calibration setting.
ZPZ IP Operating Instructions
ADJ Products, LLC - www.adj.com - 7ZP IP - User Manual Page 20
ZPZ IP Operating Instructions
Secondary Setting:
1. Press the MODE button to access the main menu. Press the UP or DOWN buttons so that “Menu Secondry”
is highlighted, then press ENTER.
2. The display will now show “Secondry” designating it as the secondary xture in a Primary-Secondary set up.
3. The display will now show “Reset. M Zoom”. Press ENTER to reset the zoom function.
Manual Control:
1. Press the MODE button to access the main menu. Press the UP or DOWN buttons so that “Menu Manual”
is highlighted, then press ENTER.
2. Use the UP and DOWN buttons to scroll through the manual settings that include Zoom, Master Dimmer,
Red Intensity, Green Intensity, Blue Intensity, White Intensity, and Strobe.
3. When you nd a setting you would like to adjust press ENTER. Use the UP and DOWN buttons to make
adjustments, then press ENTER.
ZPZ IP Primary-Secondary Configuration
Primary-Secondary Conguration:
This function will allows you to link units together to run in a Primary-Secondary mode. In Primary-Secondary
operation one unit will act as the controlling unit and the others will react to the controlling units built-in programs.
Any unit can act as a Primary or as a Secondary; however, only one unit can be programmed to act as the “Primary.”
Primary-Secondary Connections and Settings:
1. Daisy chain your units via the XLR connector on the rear of the unit. Use standard XLR data cables to link
your units together. Remember that the Male XLR connector is the input and the Female XLR connector is
the output. The rst unit in the chain (primary) will use the female XLR connector only. The last unit in the
chain will use the male XLR connector only.
2. Connect the rst “Secondary” unit to the “Primary”, and the “Secondary” unit should now start to follow the
“Primary”.
3. Set the “Primary” unit to your desired mode of operation.
4. On the “Secondary” units press the MODE button until “Menu Secondry” is displayed and press ENTER.
The unit is now set as the “Secondary” unit. Each secondary unit must be set to the same setting.
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
/
