ML Accessories LANT1WP is an IP54-rated luminaire from ML Accessories with Class II double insulation, so it is resistant to dust and splashing water, making it suitable for both indoor and outdoor use. It is powered by mains electricity and requires correct cabling methods during installation. LANT1WP provides a convenient manual override function for both PIR and photocell versions, allowing you to turn the luminaire on permanently when needed. The PIR version offers motion detection with a range of up to 8 meters, a time setting of 60 seconds, and a detection angle of 90 degrees.
ML Accessories LANT1WP is an IP54-rated luminaire from ML Accessories with Class II double insulation, so it is resistant to dust and splashing water, making it suitable for both indoor and outdoor use. It is powered by mains electricity and requires correct cabling methods during installation. LANT1WP provides a convenient manual override function for both PIR and photocell versions, allowing you to turn the luminaire on permanently when needed. The PIR version offers motion detection with a range of up to 8 meters, a time setting of 60 seconds, and a detection angle of 90 degrees.
INSTALLATION & MAINTENANCE MANUAL
LANT1 / LANT1W / LANT2 / LANT2W
LANT1BKP / LANT1WP
These instructions should be read carefully and retained after installation by the
end user for future reference and maintenance.
These instructions should be used to aid installation of the following products:
LANT1 / LANT1W / LANT2 / LANT2W / LANT1BKP / LANT1WP
GENERAL INSTRUCTIONS
SAFETY
• This product must be installed in accordance with the latest edition of the IEE Wiring
Regulations (BS7671) and current Building Regulations. If in any doubt, consult a
qualified electrician
• Please isolate mains prior to installation or maintenance
• Check the total load on the circuit (including when this luminaire is fitted) does not exceed
the rating of the circuit cable, fuse or circuit breaker
• Please note the IP (Ingress Protection) rating of this product when deciding the location
for installation
• This product is Class II double insulated
• This product series is IP54 rated
INSTALLATION & MAINTENANCE MANUAL
These instructions should be read carefully and retained after installation by the end user for future reference
and maintenance.
These instructions should be used to aid installation of the following products:
LANT1 / LANT1W / LANT2 / LANT2W / LANT1BKP / LANT1WP
SAFETY
• This product must be installed in accordance with the latest edition of the IEE Wiring Regulations
(BS7671) and current Building Regulations. If in any doubt, consult a qualified electrician
• Please isolate mains prior to installation or maintenance
• Check the total load on the circuit (including when this luminaire is fitted) does not exceed the rating of
the circuit cable, fuse or circuit breaker
• Please note the IP (Ingress Protection) rating of this product when deciding the location for installation
• This product is Class II double insulated
• This product series is IP54 rated
INSTALLATION
• Provide power to the required point of installation (refer to BS7671 for correct cabling methods).
Suitable IP rated junction boxes should be used where required
• Remove the two nuts on the front of the fitting securing the baseplate to the luminaire
• Using the baseplate as a template, mark the location for, and drill the fixing holes ensuring not to
infringe with any gas/water pipes or electrical cables
• Feed the mains cable through the rubber grommet to retain IP rating, and secure the baseplate to the
surface using the plugs, screws, and silicone washers provided (see Fig. 1)
Fig. 1
• Connect the luminaire to the mains supply ensuring the correct polarity is observed (see Fig. 2): L -
Live (brown), N - Neutral (blue). The earth terminal is non-functional and only provided for convenience
Fig. 2
• Ensuring the gasket is in place, carefully fit the luminaire onto the baseplate, securing with the two nuts
• Switch on and check for correct operation
INSTALLATION
• Provide power to the required point of installation (refer to BS7671 for correct cabling
methods). Suitable IP rated junction boxes should be used where required
• Remove the two nuts on the front of the fitting securing the baseplate to the luminaire
• Using the baseplate as a template, mark the location for, and drill the fixing holes ensuring
not to infringe with any gas/water pipes or electrical cables
• Feed the mains cable through the rubber grommet to retain IP rating, and secure the
baseplate to the surface using the plugs and screws, provided (see Fig. 1)
Fig. 1
PIR VERSION LANT2x
• Connect the luminaire to the mains supply ensuring the correct polarity is observed (see
Fig. 2): L - Live (brown), N - Neutral (blue). The earth terminal is non-functional and only
provided for convenience
• Ensuring the gasket is in place, carefully fit the luminaire onto the baseplate securing with
the two nuts
• Switch on and check for correct operation
The PIR is factory set as follows (these settings are not adjustable):
Detection range: up to 8m
Time settings: 60 seconds
Lux settings: below 15 lux
Detection angle: 90°
Manual override can be activated by switching the power off and on twice within 2 seconds.
This will turn the luminaire on permanently. To cancel and return to automatic mode, switch
the power off for at least 10 seconds.
Fig. 2
INSTALLATION & MAINTENANCE MANUAL
These instructions should be read carefully and retained after installation by the end user for future reference
and maintenance.
These instructions should be used to aid installation of the following products:
LANT1 / LANT1W / LANT2 / LANT2W / LANT1BKP / LANT1WP
SAFETY
• This product must be installed in accordance with the latest edition of the IEE Wiring Regulations
(BS7671) and current Building Regulations. If in any doubt, consult a qualified electrician
• Please isolate mains prior to installation or maintenance
• Check the total load on the circuit (including when this luminaire is fitted) does not exceed the rating of
the circuit cable, fuse or circuit breaker
• Please note the IP (Ingress Protection) rating of this product when deciding the location for installation
• This product is Class II double insulated
• This product series is IP54 rated
INSTALLATION
• Provide power to the required point of installation (refer to BS7671 for correct cabling methods).
Suitable IP rated junction boxes should be used where required
• Remove the two nuts on the front of the fitting securing the baseplate to the luminaire
• Using the baseplate as a template, mark the location for, and drill the fixing holes ensuring not to
infringe with any gas/water pipes or electrical cables
• Feed the mains cable through the rubber grommet to retain IP rating, and secure the baseplate to the
surface using the plugs, screws, and silicone washers provided (see Fig. 1)
Fig. 1
• Connect the luminaire to the mains supply ensuring the correct polarity is observed (see Fig. 2): L -
Live (brown), N - Neutral (blue). The earth terminal is non-functional and only provided for convenience
Fig. 2
• Ensuring the gasket is in place, carefully fit the luminaire onto the baseplate, securing with the two nuts
• Switch on and check for correct operation
WARNING
PHOTOCELL VERSION LANT1xxP
This luminaire must be disconnected from the circuit if subjected to any high voltage or
insulation resistance testing. Irreparable damage will occur if this instruction is not followed.
The photocell switches the light on when the light level drops to below 15 lux, and off when
the light level reaches 45 lux (these settings are not adjustable). It is sensitive to artificial
light as well as natural daylight.
Manual override can be activated by switching the power off and on 3 times within 3
seconds. This will turn the luminaire on permanently irrespective of the light level. To cancel
and return to automatic mode, switch the power off for at least 10 seconds.
GENERAL
This product contains a light source of energy efficiency class D to Regulation (EU) No.
2019/2015.
This product contains a non-replaceable LED light source and control gear.
Clean the external surfaces with a damp cloth using a mild solution of detergent and warm
water only, do not use aggressive cleaning products or solvents which may damage the
product.
Do not use any source of high-pressure washers to maintain or clean this luminaire.
This product is non-dimmable.
This product should be dismantled for disposal when it reaches the end of its life. Please
see website for dismantling instructions.
This product should be recycled in the correct manner when it reaches the end of its life.
Check local authorities for where facilities exist.
ML Accessories Limited LU5 4LT
www.mlaccessories.co.uk
DCAUG21_V3
02
WARRANTY
This product has a warranty of 3 years from date of purchase. Failure to install this product
in accordance with the current edition of the IEE Wiring Regulations (BS7671), improper
use, or removal of the batch code will invalidate the warranty. If this product should fail
within its warranty period, it should be returned to the place of purchase for a free of
charge replacement. ML Accessories does not accept responsibility for any installation
costs associated with the replacement product. Your statutory rights are not affected. ML
Accessories reserve the right to alter product specification without prior notice.
INTERNATIONAL
CONTACT DETAILS
INTERNATIONAL
CONTACT DETAILS
INTERNATIONAL
CONTACT DETAILS
-20~
50°C
TA
-
1
-
2
-
3
-
4
-
5
-
6
-
7
ML Accessories LANT1W User manual
- Type
- User manual
- This manual is also suitable for
ML Accessories LANT1WP is an IP54-rated luminaire from ML Accessories with Class II double insulation, so it is resistant to dust and splashing water, making it suitable for both indoor and outdoor use. It is powered by mains electricity and requires correct cabling methods during installation. LANT1WP provides a convenient manual override function for both PIR and photocell versions, allowing you to turn the luminaire on permanently when needed. The PIR version offers motion detection with a range of up to 8 meters, a time setting of 60 seconds, and a detection angle of 90 degrees.
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Related papers
-
ML Accessories CSP2BC User manual
-
-
-
-
-
ML Accessories ML500 User manual
-
-
-
-
Other documents
-
Knightsbridge PWRCR User manual
-
-
-
Knightsbridge E27PC User guide
-
-
Knightsbridge LWALL1A Installation guide
-
Knightsbridge TRIBCCW User manual
-
Knightsbridge OL01B User manual
-
Knightsbridge SFPLxx User manual
-