Ledalite EyeLine suspended Install Instructions

Brand: Ledalite

Model: EyeLine suspended

Type: Install Instructions

ATTENTION: Install in accordance with national and local building and electrical codes.

STANDALONE

! IMPORTANT SAFETY AND HANDLING PROCEDURES

• DO NOT POWER UP ROW UNTIL ALL FIXTURES ARE INSTALLED AND CONNECTED

• AVOID HANDLING THE BOTTOM LENS

• KEEP LUMINAIRE IN THE BOX UNTIL READY TO BE INSTALLED

• MAKE SURE ALL LUMINAIRES AND JOINT KITS ARE ACCOUNTED FOR BEFORE BEGINNING INSTALLATION

• LEAVE THE PROTECTIVE BAG ON THE FIXTURE DURING INSTALLATION

48.00" 40-3/8"

32-7/8"

40-3/8" 40-3/8"

40-3/8"

*ONLY END LUMINAIRES ARE MOUNTED AT 40-3/8”. MID RUN LUMINATRES ARE ALWAYS 48” MOUNTS*

MOUNT LOCATIONS

8FT RUN

LONGER THAN 8FT RUN

Installaon Steps Overview:

1. Install driver pods and non-powered mounts

(reference ID-DP_DriverPod.PDF)

2. Install joiner brackets in luminaires at oor

level at the ends of the rows rst

3. Install luminaires with power cords at the

end of the row

4. Install mid-run luminaires with power cords

5. Install mid-run luminaires without power

cords

6. Level row and trim aircra cable

PAGE 1

ATTENTION: Install in accordance with national and local building and electrical codes.

NOTES:

• Prior to luminaire installaon, lay out xtures to ensure correct power and non-power secons with ends and joints are supplied

• Instrucons below are based on an example run of 16, 6800LM, EM

1 INSTALL DRIVER PODS AND NON-POWERED MOUNTS (SEE ID-DP_DriverPod.PDF)

2 INSTALL JOINER BRACKETS IN LUMINAIRES AT FLOOR LEVEL AT THE ENDS OF THE ROW FIRST

END RUN WITH JUMPER

CABLES

END RUN WITHOUT

JUMPER CABLES

JOINER BRACKET

REMOVE

SCREW FROM

CIRCUIT

BOARD

SLIDE JOINER

BRACKET

INTO SLOTS

IN ENDCAP

MOVE

JUMPER

CABLES OUT

OF THE

WAY

REPLACE

SCREW IN-

TO HOLE

REMOVE

SCREW IN

ENDCAP

REPLACE

SCREW

THROUGH

JOINER INTO

ENDCAP

SLIDE JOINER

BRACKET INTO

SLOTS IN

ENDCAP

PAGE 2

ATTENTION: Install in accordance with national and local building and electrical codes.

HANG LUMINARES AT THE END OF THE ROW FIRST.

ROWS ARE CONSTRUCTED BY FISRT HANGING UNITS WITH POWER

CORDS AND FILLING IN THE GAPS WITH MID RUN NON-

POWERCORD EQUIPED UNITS.

PUSH AIRCRAFT CABLES INTO AND THROUGH ADJUSTERS. FEED POWER CORD INTO

DRIVER POD. (SEE DRIVER POD SPECIFIC SECTION FOR WIRING)

TO RELEASE AIRCRAFT CABLE PUSH UP ON THE SMALL

PLUNGER ON THE BOTTOM OF THE ADJUSTER.

CAUTION: ALWAYS HOLD ONTO LUMINAIRE

WHEN RELEASING AIRCRAFT CABLE

3 INSTALL LUMINAIRES WITH POWER CORDS AT THE END OF THE ROW

PAGE 3

ATTENTION: Install in accordance with national and local building and electrical codes.

FEED AIRCRAFT CABLE INTO ADJUSTER AND PUSH LUMINAIRES TOGETHER

REMOVE AND RETAIN SCREW FROM

LUMINAIRE THAT DOES NOT HAVE THE

JOINER PRE-INSTALLED

PUSH LUMINAIRES TOGETHER, ENSURE

THAT LOCATION TABS ON THE CROSS-

PLATES ENGAGE IN CORRESPONDING

HOLES

WHILE SUPPORTING THE LUMINAIRE

RE-INSTALL THE SCREW THAT WAS RE-

MOVED EARLIER

INSTALL THE TWO OPPOSING SCREWS

FROM MOUNT KIT TO PULL THE TWO

LUMINARES TOGETHER

4 INSTALL MID RUN LUMINAIRES WITH POWER CABLES

FEED POWER CABLE THROUGH CANOPY AND

INTO DRIVER POD. SEE DRIVER POD DOCU-

MENT FOR WIRING INSTRUCTIONS

PAGE 4

ATTENTION: Install in accordance with national and local building and electrical codes.

SLIGHTLY PUSH ROW

IN BOTH DIRECTIONS

AND SLIDE LUMI-

NAIRE ONTO PRE-

INSTALLED JOINER

BRACKETS

5 INSTALL MID RUN LUMINAIRES WITH OUT POWER CORDS

JOINT WITH POWER JUMPERS

REMOVE

SCREW FROM

TOP OF

ENDCAP AND

PUSH FIXTURES

TOGETHER

B A

RE-INSTALL

SCREWW

THROUGH

JOINER IN-

TO CROSS

PLATE

PUSH

JUMPER

WIRES

DOWN

INTO

SLOT IN

JOINER

INSTALL OP-

POSING

SCREWS TO

PULL FIXTURES

TOGETHER

JOINT WITHOUT POWER JUMPERS

B A

C INSTALL OP-

POSING

SCREWS TO

PULL FIXTURES

TOGETHER

REMOVE

SCREW

FROM TOP

OF ENDCAP

RE-INSTALL

SCREWW

THROUGH

JOINER IN-

TO CROSS

PLATE

PUSH LUMI-

NAIRES TO-

GETHER

6 LEVEL ROW

• LEVEL ROW USING TOP MOUNTED AIRCRAFT ADJUSTER (SEE ID-DP_DriverPod.PDF)

• REMOVE PLASTIC BAG WHEN BUILDING CONSTRUTION IF FINISHED

PAGE 5

Ledalite EyeLine suspended Install Instructions