2. Quadra-Fire
  3. TPVNT-1 Pellet Adapter

Quadra-Fire TPVNT-1 Pellet Adapter Installation guide

  • Hello! I've reviewed the installation instructions for the Quadra-Fire Top Vent Adapter TPVNT-1. The document details the installation process, including applying sealant, drilling holes, and securing the adapter. I’m ready to answer any questions you may have about the installation process or the components included in the kit.
  • What is included in the kit?
    What tools are required for installation?
    Where should the silicone be applied?
November 18, 20197014-279B
352 Mountain House Road
Halifax, PA 17032
www.quadrare.com
www.hearthnhome.com
Page 1 of 3
R
Included in Kit:
Tools Required:
Powered drill, Phillips head screwdriver, and high temp
silicone (500°F)
Included in kit:
Quantity one (1) Top Vent Adapter Assembly (C1),
quantity six (6) 8-32 x 3/8 inch screws (C2), and quantity
one (1) #26 Drill Bit (C3)
TOP VENT ADAPTER INSTALLATION INSTRUCTIONS
PART:
TPVNT-1
FOR PELLET APPLIANCES:
CLASSIC BAY 1200
C1
x1
C2 C3
x6 x1
5
(127)
2-1/2
(63)
26
(661)
26
(661)
23-1/8
(586)
23-1/8
(586)
1. Put a 1/4 inch bead of silicone on the outer edge of
the appliance exhaust outlet (Figure 1).
Figure 1
Silicone
Rear Exhaust
Outlet
NOTICE: Do not apply silicone inside appliance
exhaust outlet.
November 18, 20197014-279B
352 Mountain House Road
Halifax, PA 17032
www.quadrare.com
www.hearthnhome.com
Page 2 of 3
Figure 2
Figure 3
Figure 4
2. Slide the Top Vent Adapter Assembly (C1) onto the
exhaust outlet over bead of silicone making sure the
adapter is in the vertical position.
3. Slide the outer shield up or down to align evenly with
the top of stove.
4. Tighten the adjusting screws when the shield is in the
proper position (Figure 2).
5. Ensuring the adapter is in the vertical position; drill
four (4) holes with #26 Drill Bit (C3) into the back
of the stove using the outer shield on the Top Vent
Adapter Assembly (C1) as a guide, secure using four
mounting 8-32 x 3/8 inch screws (C2) (Figure 3).
Drill holes in back of stove
and secure with 4 screws, 2
on each side.
6. Drill two (2) holes with #26 Drill Bit (C3) through
the exhaust outlet using the two (2) holes already
in the short horizontal pipe in the Top Vent Adapter
Assembly (C1)as a guide; secure using two (2)
mounting 8-32 x 3/8 inch screws (C2) (Figure 4).
Drill 1 hole on each side
and secure with mounting
screws
Vent
Adapter
7. Put a 1/4 inch bead of silicone on the outer edge of
the Top Vent Adapter Assembly (C1) exhaust outlet
(Figure 5).
Silicone outer edge
Figure 5
NOTE: Following venting manufacturing instructions,
install stove pipe to Top Vent Adapter
Assembly (C1). Appliance adapter from venting
manufacture may be required. Do not apply
silicone inside appliance exhaust outlet.
November 18, 20197014-279B
352 Mountain House Road
Halifax, PA 17032
www.quadrare.com
www.hearthnhome.com
Page 3 of 3
8. After performing regular cleaning of venting, open the
clean-out cover and vacuum out debris; close when
complete (Figure 6).
Figure 6
Clean-Out Cover
/