Numark EM460 User manual

Brand: Numark

Model: EM460

Category: Musical Equipment

Type: User manual

Professional Disc Jockey Products

EM460

EM460EM460

EM460

PROFESSIONAL DJ EFFECTS MIXER

PROFESSIONAL DJ EFFECTS MIXERPROFESSIONAL DJ EFFECTS MIXER

PROFESSIONAL DJ EFFECTS MIXER

With

With With

With KAOSS* Pad Multi-effects Processor

Pad Multi-effects Processor Pad Multi-effects Processor

Pad Multi-effects Processor

Owner’s Manual

*KAOSS technology under license from KORG

EM 460

- The Leader in DJ Technology

Safety Information

SAFETY INSTRUCTIONS

a) Read Instructions - All the safety and operating

instructions should be read before this product is

connected and used.

b) Retain Instructions - The safety and operating instructions

should be kept for future reference.

c) Heed Warnings - All warnings on this product and in

these operating instructions should be followed.

d) Follow Instructions - All operating and other instructions

should be followed.

e) Water and Moisture -

This product should be

kept away from direct

contact with liquids.

f) Heat - Avoid placing this

product to close to any high heat sources such as radiators.

g) Ventilation - The appliance should be situated so that it’s

location or position does not interfere with it’s proper

ventilation. For example, the appliance should not be

situated on a bed, sofa, rug, or similar surface that may

block the ventilation opening;

or, placed in a built-

installation, such as bookcase

or cabinet that may impede

the flow of air through the

ventilation openings.

h) Power Sources - This product should be connected to a

power supply only of the type described in these operating

instructions, or as marked on the unit.

i) Power Cord Protection - Power supply cords should be

routed so that they are not likely to be walked upon or

pinched by items placed on or against them. When

removing the cord from a power outlet be sure to remove

it by holding the

plug attachment

and not by pulling

on the cord.

j) Object and Liquid Entry - Take care that objects do not

fall into and that liquids are not spilled into the inside of

the mixer.

k) Cleaning – The appliance should be cleaned only as

recommended by the manufacturer.

Non-use Periods – The power cord of the appliance

should be unplugged from the outlet when left unused for

long periods of time.

m) Damage Requiring Service - Never attempt to make any

adjustments or repairs other

than those described in this

manual.

Only qualified

personnel should service

this product. If you have

any questions about service

please contact Numark at the number(s) shown on the

back cover of this manual.

n) Grounding or Polarization - Precautions should be taken

so that the grounding or polarization means built into the

CD player is not defeated.

o) Internal/External Voltage Selectors - Internal or external

voltage selector switches, if any, should only be reset and

re-equipped with a proper plug for alternative voltage by a

qualified service technician. Do not attempt to alter this

yourself.

WARNING: To reduce the risk of fire or electrical shock, do

not expose this appliance to rain or moisture. Electrical

equipment should NEVER be kept or stored in damp

environments.

EM460

- The Leader in DJ Technology

EM460

EM460EM460

EM460

PROFESSIONAL DJ EFFECTS MIXER

With

With With

With KAOSS PAD Multi-effects Processor

PAD Multi-effects Processor PAD Multi-effects Processor

PAD Multi-effects Processor

CONGRATULATIONS!

You have purchased the EM460 Stereo Effects Mixer by . The first series of DJ mixers with a

completely interactive, real-time effects processor. This one of a kind DJ product boasts all of the qualities that

you have come to expect from a

mixer plus, it features a built in KAOSS PAD*. This piece of

equipment literally puts effects processing at the DJ’s fingertips. The EM460 is easily suited for mobile or

installation use. Special features found on this product are eight line inputs, rotary cut control, balanced outputs,

and fader start. The fader start feature is designed to work with ’s Fader Start CD players as well as its

other popular CD players. The KAOSS Pad* effects processing unit lets the DJ control his choice of up to

sixty effects programs in real-time. The effects unit allows for sampling functions, parameter controls, and

MIDI compatibility.

Thank you for purchasing NUMARK products!

Mixer Features:

• Eight line, three phono, two mic inputs

• Front panel Neutrik

mic input

• Master with Balanced outputs with EQ and Panning

• 3-band EQ, Pan, and gain control on all channels

• Completely assignable and replaceable cross-fader

• Fader start

• 2 Zone outputs

• Split/blend headphone cueing

KAOSS PAD* Features:

• Real-time effects processing

• X-Y touch sensitive pad

• Separate parameter controls

• Sixty “effects programs”

• Hold switch to lock in settings

• Sampler (5 seconds at 48 kHz)

• MIDI compatibility

• 100% digital processing

*KAOSS technology under license from KORG

Table of Contents

Safety Measures 2

Introduction 3

Registration 3

Description of the Features 4

Quick Setup Diagram 7

KAOSS Effects 8

MIDI Implementation 9

Specifications 10

Bock Diagram 11

Warranty 12

Product Registration

Please record the serial number of your unit as shown on the back of the chassis as well as the name of the

dealer from whom you purchased the unit. Retain this information and your original purchase receipt for

your records. Please return the enclosed warranty card to register your unit with us.

MODEL: __________________________ PURCHASED FROM:_________________________

SERIAL NUMBER:__________________ DATE OF PURCHASE:________________________

EM460

- The Leader in DJ Technology

MIXER FEATURES

91011 12

20 21

INPUTS

1. Input faders - control individual source levels in the mix.

Note: Never use spray cleaners on the slide controls. Residues

cause excessive dirt build-up and this will void your warranty.

In normal use slide controls can last for many years. If they

malfunction (usually because of a dirty or dusty environment)

consult a professional technician.

2. Input Toggle Switches - select which source will be live to that

channel based on what you have connected to the rear panel

input section.

3. Panning – adjusts the balance of right to left audio

4. 3-Band Stereo Equalizer (EQ) - compensates for differences in

source material sound quality. You can create interesting effects

by removing frequencies if you turn the knob to –30dB.

5. PFL Gain – allows you to adjust the input level of the music to

match other channels. The idea is to set all input levels to

approx. 0dB so channels match. Do not try to match to the

master output meter.

6. PFL Meter – to allow for precise matching of channel input

levels.

7. Neutrik™ “Combo” connector - allows connection of either a

1/4” jack or an XLR jack. This is ideal for connecting an XLR

gooseneck directly into the mixer.

HEADPHONE CUEING

8. Channel Cue Assign - are used to route Pre Fader Level (PFL)

channel audio to the Monitor Section. The channel faders do

not control the Cue volume.

9. Headphone Mix - controls the mix of PFL and PGM signals to

your headphones. When the slider is moved to the left, all you

will hear is the cue source. When the slider is all the way to the

right, you will hear what is playing through the master output.

By blending, beats can be matched exactly and segues can be

smooth when a song is cued.

10. Headphone Level – adjusts cue volume.

11. Split/Blend Cue – controls how PFL and Program audio are

sent to your headphones. In split mode, the PFL audio can be

heard in your left ear and PGM audio can be heard in your right

ear. In blend mode, both PFL and PGM can be heard in both

ears.

12. Headphone output – for your 1/4” headphones.

OUTPUTS

13. Master Fader – controls the overall output level.

14. Stereo/Mono toggle - adjusts the Master output for stereo or

mono operation.

15. Panning – adjusts the output balance of right to left audio.

16. 3-Band Stereo Equalizer (EQ) - compensates for differences in

source material sound quality. In ultra-compact mobile systems

this EQ can be used to tailor the sound to the acoustical

requirements of the room.

17. Booth/Zone Fader - controls speaker volume for a remote zone

or booth monitors.

NOTE: This can also be used to supply line level audio to a

lighting controller or to lights that are sound activated.

18. Stereo Auto Peak Hold Level Indicator- quickly and

accurately tracks level of audio output. The red LEDs for +3dB,

+5dB and +8dB hold program peaks for a second or two. With

peak metering, it's OK to be "in the red" as long as +5dB or

+8dB aren't constantly lit. When using as a master output

meter, set the crossover, equalizer and power amp inputs to

avoid distortion at each step in the audio chain. Proper attention

to the peak meter results in the punchiest possible sound without

audible distortion.

EM460

- The Leader in DJ Technology

CROSSFADER

19. Replaceable Crossfader - achieves clean segues between the

two input channels selected by the Crossfader Assign.

Note: The crossfader is a user replaceable item and subject to

wear. Excessive force can wear out the fader quickly. This is

not a warranted item. In case of failure. Simply unscrew the two

large screws that hold it in place, lift it out and disconnect its

cable. Re-attach the new crossfader and screw the mounting

plate back onto the unit - you’re back in business!

20. Crossfader Assign Knob - determines which input channel will

be heard when the crossfader is moved towards the knob. With

the crossfader centered, both assigned channels are live. Use the

crossfader for fast and seamless segues from one selected

channel to the other.

21. Fader Start – activates the crossfader to send play and cue

commands to your auto-start Numark CD player or other

popular brand. For fader start, attach your mixer to a remote

start CD player using industry standard 1/8”(3.5mm) cables.

When you move the crossfader toward the active channel, the

attached CD player will start. When it is moved away, that side

will cue (similar to pressing the cue button).

KAOSS PAD*

22. Process buttons – send post channel fader audio to the KAOSS

PAD for processing.

23. Process Blend Control – mixes processed (efx)-wet audio with

unprocessed (src)-dry audio. Use this in conjunction with the

KOASS pad to reach desired effects.

24. Preset Program keys (1–6)- You can assign programs to keys

1–6 for convenient selection.

Program assignment:

a) Press one of the PROGRAM MAP keys.

b) Use the PROGRAM knob to select the program that

you wish to assign. If you wish to memorize the

HOLD setting, turn the HOLD switch to ON after

selecting the program, and touch the touch panel to

specify the position.

c) Press and hold the PROGRAM MAP key you pressed

in step 1 for approximately two seconds.

25. Touch panel- You can control the sound by using your finger to

rub or tap (strike lightly) this panel. Never press down too

hard on the touch panel, or place a heavy object on it. Rough

handling can cause it to crack or break. Rubbing or pressing

the touch panel with a sharp object can scratch it, so only use

your finger to operate it. If cleaning is necessary, wipe only

with a soft dry cloth. Using solvents such as thinner may melt

the surface of the touch panel. Note: Affix the included

protective label to extend product life.

26. Hold Switch- When this switch is ON, the current state of the

effect will be maintained even if you remove your finger from

the touch panel.

27. Program Knob- Use this knob to select programs (1–60).

Please see page for a complete listing of effects.

28. Program/Location Display- This shows either the currently

selected program number or the location of the point that you

touched on the touch panel, depending upon mode.

•

When selecting a program: the program number (1–60) will

be displayed.

•

When operating the touch panel: the position you touched

(1.1–9.9) with 5.5 being the center) will be displayed.

Example display: 3.8

vertical position is (3) / horizontal position is (8)

If you select a program that has a Hold On setting, the

program number will be displayed, and then the position

that is being held will be displayed.

29. EFX ON/OFF / Sample Record switch- This can be used to

switch between the effect sound and the direct (unprocessed)

sound, or to record a sample.

When sampling this button lets you record a phrase that you

hear and then play it back by operating the touch panel.

Use the following procedure to record and playback samples.

•

Using the PROGRAM knob or the PROGRAM MAP keys,

select a sample/play effect (program numbers 51–60). The

REC switch LED will blink, and the KAOSS PAD will be in record-ready

mode. At this time, the sound will be output without any change.

•

Press the REC switch to begin recording.

•

Press the REC switch once again to stop recording. The REC

switch LED will light. Even if you do not press the REC

switch, recording will end automatically when the maximum

recording time has elapsed. (The maximum recording time

will depend on the program.)

•

Operate the touch panel to playback the recorded phrase. The

sound will change depending on the position where you

touch the panel. The way in which the sound changes will

depend on the program.

•

To re-record, press the REC switch again. The previously

recorded phrase will be erased, and a new phrase will be

recorded.

If you change programs to a non-sample program, the

recorded phrase will be erased.

*KAOSS technology under license from KORG

EM460

- The Leader in DJ Technology

REAR PANEL FEATURES

10 9

777

1. Power Switch – To turn unit on after you have turned on

all input devices and before you turn on any devices

attached to the output.

2. IEC Power Cord Receptacle - To plug your power cord

in before switching on power. See safety precautions on

page 3 for proper treatment of power.

3. Voltage Selector Switch – To select the proper power for

your region. Please check carefully that this switch is set

properly for your area before plugging the unit in.

4. Phono/Auxiliary Inputs – Plug your turntables or line

device in here. Select the AUX/PHONO switch (6) to the

desired input.

5. Phono/Auxiliary switch – Select the appropriate position

for your input device. With phono selected the input

signal is fed directly to the PRO SM-1's high-quality

RIAA phono pre-amplifiers so use this input only for

turntables. Line level sources will overload the sensitive

phono pre-amps. Switch this over to the AUX position

for line devices such as CD players and Tape decks.

6. Ground lug - Use these connections with your turntables’

grounding cable to avoid signal hum.

7. Line Inputs - To connect stereo audio from HiFi VCRs,

cassette and reel-to-reel tape decks, DAT machines, CD

players, laser discs, tuners, even synthesizers or other

mixing consoles.

NOTE: Plug mono audio sources into both Left and

Right inputs using a “Y" cable connector.

8. Mic Inputs – for plugging in your ¼” mic connector

plugs.

9. Record Outputs – Unbalanced output used to send the

output of the program to any connected recording device.

10. Zone/Booth Outputs - Unbalanced output controlled by

Zone Level control on the face panel for extra speakers,

lighting, or recording your mix.

11. Unbalanced Main Outputs – Unbalanced program

output controlled by the Master fader knob.

12. Balanced Outputs - These XLR Stereo Main Outputs are

reliable Balanced connectors controlled by the Master

fader knob. Power transformers and other devices, which

cause magnetic fields, can induce hum in audio cables.

This can be best resolved by using balanced lines where

inputs and outputs permit. Balanced lines are also the

most effective means of reducing or eliminating RF or

radio frequency" interference.

13. Fader Start Connector – to attach your mixer to a

remote start equipped Numark CD player using industry

standard 1/8”(3.5mm) cables.

14. MIDI Output – Attach Midi output to external

processors to be controlled by the KAOSS Pad. See page

9 for details on signal output.

EM460

- The Leader in DJ Technology

QUICK SETUP DIAGRAM

VERY IMPORTANT: Please read this entire manual before connecting this unit to your system

For optimum performance:

•

Always make sure that AC power is OFF while making any connections.

•

Use appropriate cables throughout your system. Do not use excessively long cables (i.e. over 50ft/14m) Be sure plugs and jacks are tightly

mated. Loose connections can cause hum, noise or intermittence that could easily damage your speakers. Make the input and output

connections with readily available low-capacitance stereo cables. Quality cable makes a big difference in audio fidelity and punch. See

your Numark dealer or an electronics or audio specialist store if you are not sure which cables to get.

•

ALWAYS remember: “TURN AMPS ON LAST AND OFF FIRST”. Begin with master faders or volume controls on minimum and the

amplifier gain/input control(s) down. Wait 8 to 10 seconds before turning up the volume. This prevents transients, which may cause severe

speaker damage.

•

Use restraint when operating controls. Try to move them slowly. Rapid adjustments could damage speakers due to amplifier clipping.

Avoid amplifier “clipping” at all costs: this occurs when the red LEDs (usually on the front panel of most professional power amplifiers)

start flashing. “Clipping” is when the power amplifier is distorting and working beyond it’s limits. Amplifier distortion is THE major cause

of speaker failure.

Study this setup diagram. Make sure all faders are at "zero" and all devices are off. First, connect all

input sources and processors. Next, connect your microphone and monitor headphones. Finally, connect the

stereo outputs to the power amplifier(s) and/or audio receivers such as tape decks. Plug your mixer into AC

power. Now you are ready to switch everything on.

IMPORTANT: Always switch on your audio input sources such as turntables or CD players first, then your

mixer, and finally any amplifiers. When turning off, always reverse this operation by turning off amplifiers,

then your mixer, and then input devices.

EM460

- The Leader in DJ Technology

KAOSS PROGRAM EFFECTS

Effect program control parameter list

NO. EFFECT X (horizontal position) Y [-Y, +Y] (vertical position) Comment

1 LOW PASS FILTER FREQ DI/FX BALANCE, RESONANCE Rub slowly

2 LOW PASS FILTER FREQ RESONANCE Rub slowly

3 WAH FILTER FREQ DI/FX BALANCE, LFO DEPTH Rub slowly

4 DIST+VOICE FILTER FREQ DIST GAIN Rub fast with beat

5 DIST+L.P FILTER FREQ DIST GAIN Rub fast with beat

6 DIST+L.P FILTER FREQ RESONANCE Good for voice (Mic)

7 PAN+FILTER PAN FREQ Rub (1.1 <–> 9.9)

8 DIST+FILTER FREQ FX BALANCE, DIST GAIN Rub fast with beat

9 ISOLATOR TYPE FILTER FREQ NO ASSIGN For “Bass Cut”

10 DISTORTION GAIN LEVEL For “HOLD” use

11 PHASER FREQ (MANUAL) DI/FX BALANCE, RESONANCE Rub slowly

12 PHASER LFO SPEED FREQ (MANUAL) Rub slowly

13 LFO WAH LFO SPEED FX BALANCE Rub fast with beat

14 STEP PHASER LFO SPEED MOD STEP Rub slowly

15 DIST+PHASER LFO SPEED DIST GAIN Rub slowly

16 MANUAL FLANGER DELAY TIME RESONANCE Rub very slowly (L <–> R)

17 MANUAL FLANGER DELAY TIME RESONANCE Rub very slowly (L <–> R)

18 PITCH SHIFT Lch PITCH Rch PITCH Rub

19 TREMOLO LFO SPEED LFO DEPTH Rub

20 STEP PHASER LFO SPEED RESONANCE Rub slowly

21 TAPE ECHO TIME FX LEVEL, FEEDBACK Rub (Bottom <–> Top)

22 DELAY TIME FX LEVEL Tap with snare drum

23 DELAY TIME FX LEVEL, FEEDBACK Rub

24 STEREO TAPE ECHO TIME FREQ Rub or tap

25 MEDIUM DELAY FEEDBACK FX LEVEL Rub fast

26 LONG DELAY FEEDBACK FX LEVEL Rub fast

27 X DELAY FEEDBACK FX LEVEL Rub or tap

28 TALK FILTER+DELAY FILTER FREQ DELAY LEVEL Rub with beat

29 DIST+FILTER+DELAY FREQ DELAY LEVEL Rub with beat

30 DELAY+FILTER FOR DUB TIME FREQ Rub or tap

31 REVERB (HALL) LOW CUT FX LEVEL Tap with snare drum

32 GATE REVERB (HALL) LOW CUT FX LEVEL Tap with snare drum

33 REVERB (PLATE) LOW CUT FX LEVEL Tap with snare drum

34 GATE REVERB (ROOM) LOW CUT FX LEVEL Tap with snare drum

35 DELAY+REVERB DELAY LEVEL REVERB LEVEL For “HOLD” use

36 DELAY+REVERB DELAY TIME FX LEVEL For “HOLD” use

37 TALK FILTER+REVERB FILTER FREQ FX LEVEL Rub fast with beat

38 DIST+FILTER+REVERB FILTER FREQ REV LEVEL+RESONANCE Tap with snare drum

39 REVERB+PAN PAN FX LEVEL Rub for panning

40 REVERB REVERB TIME FX LEVEL For “HOLD” use

41 STEP MODULATION MOD DEPTH FX LEVEL Rub slowly

42 RING MOD+FILTER RING FREQ FILTER FREQ Tap at random

43 RING+TALK MOD MOD SPEED RING FREQ As you like

44 SPECIAL ECHO TIME FX LEVEL Rub at random

45 RING+DELAY TIME RING+DELAY BALANCE Rub at random

46 DELAY+TREMOLO TIME+LFO SPEED DLY+TREM X-FADE Rub in circle

47 3D PAN PAN (L/R) NEAR/FAR Rub for panning

48 VIBRATE SPEED+DEPTH FX BALANCE Rub (Bottom <–> Top)

49 STEP FLANGER FREQ (MANUAL) FEEDBACK Rub slowly

50 STEP PHASER LFO SPEED FX LEVEL Rub slowly

51 SAMPLE/PLAY1 LOOP TIME FX LEVEL Tap for playback

52 SAMPLE/PLAY2 FORWARD/REVERSE FX LEVEL Rub like scratch

53 SAMPLE/PLAY3 TIME STRETCH FX LEVEL Rub for “TIME STRETCH”

54 SAMPLE/PLAY1 (*AUTO REC) LOOP TIME FX LEVEL Tap for playback

55 SAMPLE/PLAY2 (*AUTO REC) FORWARD/REVERSE FX LEVEL Rub like scratch

56 SAMPLE/PLAY3 (*AUTO REC) TIME STRETCH FX LEVEL Rub for “TIME STRETCH”

57 SAMPLE/PLAY1 (DIRECT MIX TYPE) LOOP TIME FX LEVEL Tap for playback

58 SAMPLE/PLAY2 (DIRECT MIX TYPE) FORWARD/REVERSE FX LEVEL Rub like scratch

59 SAMPLE/PLAY1+PAN PAN LOOP TIME Tap (L <->R)

60 SAMPLE/PLAY2+PAN PAN FORWARD/REVERSE Tap (L <->R)

*(AUTO REC): After you press the REC switch, recording will begin automatically when sound is input. When you press the REC switch once

again, recording will end. (This is convenient when recording your voice from a mic.)

EM460

- The Leader in DJ Technology

MIDI FUNCTIONS

With the factory settings, each operation will transmit the following MIDI messages.

Operation MIDI messages transmitted Transmission on/off

Pitch bend messages En 00 00–En 7F 7F PROGRAM MAP1

Touch panel X-axis

Effect Control 1 message (CC#12)* Bn 0C 00–Bn 0C 7F PROGRAM MAP5

Modulation 1 Depth message (CC#1) Y = 5–9 Bn 01 00–Bn 01 7F PROGRAM MAP2

Touch panel Y-axis

Modulation 2 Depth message (CC#2) Y = 5–1 Bn 02 00–Bn 02 7F PROGRAM MAP3

Touch panel

X+Y axis (diagonal)

Effect 3 Depth message (CC#93)* Bn 5D 00–Bn 5D 7F PROGRAM MAP4

Touch panel on/off

Effect 2 Depth message (CC#92)* Bn 5C 7F/Bn 5C 00 HOLD switch

FX ON/OFF

Effect 4 Depth message (CC#94)* Bn 5E 7F/Bn 5E 00 FX ON/OFF

Change Program

Program Change message (1–60) Cn 00–Cn 38

*The MIDI messages that are transmitted can be selected in the range of CC#1–CC#31 and CC#64–CC#95. In MIDI Edit mode (

“MIDI transmission settings”) you can hold down the corresponding switch and rotate the PROGRAM knob to select the desired

control number.

A control number that has already been assigned cannot be selected in duplicate.

MIDI transmission settings

When you press the six PROGRAM MAP keys simultaneously, you will enter MIDI Edit mode. If you then perform no operation for

approximately 10 seconds or if you touch the touch panel, you will return to normal mode.

In MIDI Edit mode, you can use the following operations to change the MIDI transmission settings.

• PROGRAM knob: Set the MIDI transmission channel (1–16)

• PROGRAM MAP keys, FX ON/OFF, HOLD switches: Turn transmission on/off for each type of MIDI message (refer to

“Transmission on/off” in the above table).

Precautions with the KAOSS PAD

Usage -Never press down too hard on the touch panel, or place a heavy object on it. Rough handling can

cause it to crack or break. Rubbing or pressing the touch panel with a sharp object can scratch it, so only

use your finger to operate it. If cleaning is necessary, wipe only with a soft dry cloth. Using solvents such as

thinner may melt the surface of the touch panel. Note: Affix the included protective label to extend product

life.

Location -Using the unit in the following locations can result in a malfunction.

• In direct sunlight

• Locations of extreme temperature or humidity

• Excessively dusty or dirty locations

• Locations of excessive vibration

Interference with other electrical devices -This product contains a microcomputer. Radios and televisions placed

nearby may experience reception interference. Operate this unit at a suitable distance from radios and

televisions.

Handling -To avoid breakage, do not apply excessive force to the switches or controls.

Care -If the exterior becomes dirty, wipe it with a clean, dry cloth. Do not use liquid cleaners such as benzene or

thinner, or cleaning compounds or flammable polishes.

EM460

- The Leader in DJ Technology

SPECIFICATIONS

INPUTS:

Line: 10Kohm input impedance

110mV rms sensitivity (for 1.22V output)

Mic: 10Kohm input impedance unbalanced

1.6 mV rms sensitivity (for 1.22V output)

500mV rms max input

Phono: 47Kohm input impedance

1.8mV rms sensitivity @ 1 KHz (for 1.22V output)

OUTPUTS:

Line: 9V rms max

Headphone Amp: 1V rms watt into 16ohm

Distortion: less than 0.01%

SIGNAL TO NOISE RATIOS* (vs. maximum output):

Line: Better than 90 dB

Mic: Better than 77 dB

Phono: Better than 85 dB

*JIS - weighted

FREQUENCY RESPONSE:

Line: 20 Hz- 22k Hz ±0.5 dB

Line: 20 Hz- 20k Hz ±0.5 dB

Phono: ±1 dB except for controlled attenuation of -3 dB

@ 20 Hz to reduce rumble and feedback

EQUALIZER:

±12dB @ 100Hz

±6dB @ 500Hz

±12dB @ 10KHz

KOASS PAD:

Programs: 60

Sampling length: 5 Seconds

POWER CONSUMPTION:

10 Watt typical

15 watt with full headphone output

DIMENSIONS:

480mm(W) x 265mm(H) x 95mm(D)

19” (W) x 10 1/2” (H) x 4 (D)

WEIGHT:

PRO SM-3

- The Leader in DJ Technology

BLOCK DIAGRAM

Professional Disc Jockey Products

LIMITED PRODUCT WARRANTY

What is covered and for how long?

1. NUMARK INDUSTRIES LCC ("NUMARK") warrants to the original purchaser that NUMARK products; including but not limited to DJ mixers, amplifiers, CD players, CD Mix

Stations, turntables, preamplifiers, beatkeepers, equalizers, microphones, headphones, cartridges, and all other accessories; are to be free from defects in material and

workmanship under normal use and service for the period commencing upon the date of purchase from an authorized NUMARK dealer for a period of (1) Year.

What is not covered? This Limited Warranty is conditioned upon proper use of the product by the purchaser.

2. This Limited Warranty does not cover: (a) defects or damage resulting from accident, misuse, abuse, neglect, unusual physical or electrical stress, modification of any part of the

product, or cosmetic damage; (b) equipment that has the serial number removed or made illegible; (c) all plastic surfaces and other externally exposed parts that are scratched or

damaged due to normal use; (d) defects or damage from improper testing, operation, maintenance, installation, adjustment, or service of the mixers; (e) crossfaders.

3. What are NUMARK'S obligations? During the applicable warranty period, NUMARK will repair or replace, at NUMARK'S sole discretion, without charge to the purchaser, any

defective component part of the mixer. To obtain service under this Limited Warranty, purchaser must first contact NUMARK and obtain a return authorization number ("RA#").

Purchaser must then return the mixer to NUMARK in an adequate container for shipping, accompanied by purchaser's sales receipt or comparable proof of sale showing the date

of purchase, the serial number of the product, and the seller's name and address. To obtain an RA# and assistance on where to return the mixer, contact NUMARK customer

service at 401-295 9000. Upon receipt, NUMARK will repair or replace the defective products. NUMARK may, at NUMARK'S sole discretion, use rebuilt, reconditioned, or new

parts or components when repairing any product or replace a product with a rebuilt, reconditioned or new product. Repaired mixers will be warranted for a period equal to the

remainder of the original Limited Warranty on the original mixer or for (90) days, whichever is longer. All replaced parts, components, boards and equipment become the property

of NUMARK. If NUMARK determines that any mixer is not covered by this Limited Warranty, purchaser must pay all parts, shipping, and labor charges for the repair or return of

such mixer.

4. What are the limits on NUMARK'S liabilities? THE WARRANTIES GIVEN IN THIS LIMITED WARRANTY, TOGETHER WITH ANY IMPLIED WARRANTIES COVERING

NUMARK MIXERS, INCLUDING WITHOUT LIMITATION ANY WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE, ARE LIMITED TO THE

DURATION OF THIS LIMITED WARRANTY. EXCEPT TO THE EXTENT PROHIBITED BY APPLICABLE LAW, NUMARK SHALL NOT BE LIABLE FOR ANY SPECIAL,

INCIDENTAL, CONSEQUENTIAL, INDIRECT OR SIMILAR DAMAGES, LOSS OF PROFITS, DAMAGES TO PURCHASER'S PROPERTY, OR INJURY TO PURCHASER OR

OTHERS ARISING OUT OF THE USE, MISUSE OR INABILITY TO USE ANY NUMARK MIXER, BREACH OF WARRANTY, OR NEGLIGENCE, INCLUDING BUT NOT

LIMITED TO NUMARK'S OWN NEGLIGENCE, EVEN IF NUMARK OR ITS AGENT HAS BEEN ADVISED OF SUCH DAMAGES, OR FOR ANY CLAIM BROUGHT AGAINST

PURCHASER BY ANY OTHER PARTY. THIS LIMITED WARRANTY IS THE COMPLETE WARRANTY FOR NUMARK'S MIXERS, AND IS GIVEN IN LIEU OF ALL OTHER

EXPRESS WARRANTIES. THIS LIMITED WARRANTY SHALL NOT EXTEND TO ANYONE OTHER THAN THE ORIGINAL PURCHASER OF THIS PRODUCT AND STATES

PURCHASER'S EXCLUSIVE REMEDY. IF ANY PORTION OF THIS LIMITED WARRANTY IS ILLEGAL OR UNENFORCEABLE BY REASON OF ANY LAW, SUCH PARTIAL

ILLEGALITY OR UNENFORCEABILTY SHALL NOT AFFECT THE ENFORCEABILITY OF THE REMAINDER OF THIS LIMITED WARRANTY WHICH PURCHASER

ACKNOWLEDGES IS AND WILL ALWAYS BE CONSTRUED TO BE LIMITED BY ITS TERMS OR AS LIMITED AS THE LAW PERMITS.

5. This Limited Warranty allocates risk of product failure between purchaser and NUMARK, and NUMARK'S product pricing reflects this allocation of risk and the limitations of liability

contained in this Limited Warranty. The agents, employees, distributors, and dealers of NUMARK are not authorized to make modifications to this Limited Warranty, or make

additional warranties binding on NUMARK. Accordingly, additional statements such as dealer advertising or presentation, whether oral or written, do not constitute warranties by

NUMARK and should not be relied upon.

6. How does state law apply to this warranty? SOME STATES DO NOT ALLOW THE EXCLUSION OR LIMITATIONS OF INCIDENTAL OR CONSEQUENTIAL DAMAGES OR

HOW LONG AN IMPLIED WARRANTY LASTS, SO THE ABOVE LIMITATIONS OR EXCLUSIONS MAY NOT APPLY TO PURCHASER.

This Limited Warranty gives you specific legal rights. You may also have other rights, which vary from one jurisdiction to another.

RETURN INFORMATION

a) A Return Authorization number must be obtained from Numark through the address or phone numbers below.

b) A copy of the original sales receipt must also be included for the equipment to be repaired under warranty.

c) The faulty equipment must be packed in its original packaging.

d) One additional outer layer of packaging must be included to ensure product safety. Failure to do so may inadequately protect the equipment in transit and, therefore,

jeopardize the customer’s warranty.

e) Numark will not accept COD shipments and no call tags will be issued for merchandise return.

f) Numark will not return repaired merchandise to customers by priority service, unless by written request at the customer’s cost. Requests must be submitted in writing

with merchandise returned.

g) The defective Numark equipment should be sent, FREIGHT PREPAID with Return Authorization number clearly printed on the outer packaging and original sales

receipt enclosed to:

INDUSTRIES

Attention: Service Department

11 Helmsman Avenue

North Kingstown, RI 02852 USA

Phone: +1 (401) 295-9000

Fax:: +1 (401) 295-5200

Web: www.numark.com