Kenmore 625.38306 User manual

OWNER'S MANUAL

Water Softener

with Deluxe Valve

300 Series

MODEL NO. 625.383060

Caution:

Read and follow all safety rules and operating

instructions before first use of this product.

Questions ?

Visit www.KenmoreWater.com

or call toll free 1-800-426-9345 (M - F, 7 AM - 6 PM CST)

Repair or Parts ? Call toll free 1-800-469-4663

See back cover for other Sears service numbers.

SAVE THIS MANUAL

Use the plastic bag and tie provided, to hang manuals nearby the

softener for future reference.

• Warranty

• Installation

• Start Up / Setting

• How It Works

• Care Of

• Specifications

• Repair Parts

Timer

System tested and certified by NSF

International against NSF/ANSI Standard 44

for water softener performance.

®

Printed on recycled paper

Sears Brands Management Corporation, Hoffman Estates, IL 60179 U.S.A.

PRINTED IN U.S.A. www.KenmoreWater.com Part No. 7282580 (Rev. R 7/22/10)

WARRANTY ON WATER SOFTENER

ONE YEAR LIMITED WARRANTY ON WATER SOFTENER

When installed, operated and maintained according to all instructions supplied with the product, if this

Kenmore appliance fails due to a defect in material and workmanship within one year from the date of pur-

chase, call 1-800-4-MY-HOME ®to arrange for free repair.

TEN YEAR LIMITED WARRANTY AGAINST LEAKS

When installed, operated and maintained according to all instructions supplied with the product, if the water

softener tank or salt storage drum develops a leak within ten years from the date of purchase, call 1-800-4-

MY-HOME ®to arrange for free tank or drum replacement. After the first year you must pay an initial trip

charge.

All warranty coverage does not include water softener resin, which is an expendable item.

If this water softener is ever used for other than private family purposes, all warranty coverage applies for

only 90 days from the date of purchase.

This warranty covers only defects in material and workmanship. Sears will NOT pay for:

1.A service technician to instruct the user in correct product installation, operation or maintenance.

2. A service technician to clean or maintain this product.

3. Damage to or failure of this product if it is not installed, operated or maintained according to the all instruc-

tions supplied with the product.

4. Damage to or failure of this product resulting from accident, abuse, misuse or use for other than its intend-

ed purpose.

5. Damage to or failure of this product caused by the use of detergents, cleaners, chemicals or utensils other

than those recommended in all instructions supplied with the product.

6. Damage to or failure of parts or systems resulting from unauthorized modifications made to this product.

Disclaimer of implied warranties; limitation of remedies

Customer's sole and exclusive remedy under this limited warranty shall be product repair as provided herein.

Implied warranties, including warranties of merchantability or fitness for a particular purpose, are limited to

one year or the shortest period allowed by law. Sears shall not be liable for incidental or consequential dam-

ages. Some states and provinces do not allow the exclusion or limitation of incidental or consequential dam-

ages, or limitation on the duration of implied warranties of merchantability or fitness, so these exclusions or

limitations may not apply to you.

This warranty applies only while this appliance is used in the United States or Canada.

This warranty gives you specific legal rights, and you may also have other rights which vary from state to

state.

Sears Brands Management Corporation, Hoffman Estates, IL 60179

Sears Canada Inc., Toronto, Ontario, Canada M5B 2M5

2

Questions? Call The Kenmore Water Line 1-800-426-9345

TABLE OF CONTENTS

Safety Guides ................................................................................................................................................. 4

Unpack and Check Shipment ........................................................................................................................ 5

Plan Your Installation: Tools Needed, Materials Needed ........................................................................... 6-10

Install Inlet/Outlet Adapters or Bypass Valves, Three Way Valves ........................................................... 11-12

Install Softener and Connect Pipes ................................................................................................................ 13

Connect Valve and Salt Tank Drains .............................................................................................................. 14

Leak Test ........................................................................................................................................................ 15

Electrical Requirements ................................................................................................................................. 16

Install Covers and Restart Water Heater ....................................................................................................... 17

Program the Timer .................................................................................................................................... 18-19

Sanitize the Water Softener ........................................................................................................................... 20

Add Salt to Storage Tank ................................................................................................................................ 21

Install Checklist .............................................................................................................................................. 22

Faceplate Timer Features ......................................................................................................................... 23-24

How Your Water Softener Works .............................................................................................................. 25-27

Care of Your Water Softener ..................................................................................................................... 28-31

Specifications ............................................................................................................................................ 32-33

Service Tech Information ........................................................................................................................... 34-40

Exploded Views and Parts Lists ................................................................................................................ 42-47

Sears Tech Support ......................................................................................................................... Back Cover

FACTS AND FIGURES TO KEEP

Fill in the blanks below and keep this book in a safe place

so you always have these facts.

Water Softener Model No.*

Serial Number

Date Installed

Water Hardness

Iron Content

pH

Water Pressure

Water Flow Rate

Grains Per Gallon

Parts Per Million

Taste and/or Odor

Pounds/Square Inch

Gallons Per Minute

Salt Hole Cover

!

* The model number is on the rating decal, located on the rim, under the salt hole cover.

Questions?

Call the Kenmore Water Line at 1-800-426-9345

or visit KenmoreWater.com

For repair or replacement parts, call toll-free 1-800-366-7278

See back cover for other Sears service numbers.

Questions? Call The Kenmore Water Line 1-800-426-9345

Read all steps, guides and rules carefully before installing and using your new water softener.

Follow all steps exactly to correctly install. Failure to follow them could cause personal injury

or property damage. Reading this book will also help you to get all of the benefits from your

water softener.

Your Kenmore Water Softener will remove hardness minerals from water. This is measured in

grains per gallon (gpg). It will also remove some clear water iron*. This is measured in parts

per million(ppm). See the specifications page for the maximum limits of hardness and iron

removal.

• A water softener will not improve other water problems such as acidity, tastes and odors, or

iron other than clear water iron. Itwill not purify contaminated water, or make unsafe water

safe to drink.

Check with your local public works department for plumbing, electric and sanitation codes.

You must follow their guides as you install your softener. Use only LEAD FREE SOLDER

AND FLUX, as required by federal and state codes, when installing soldered copper plumb-

ing.

Protect the softener and piping from freezing. Damage from freezing voids the softener war-

ranty. See how to protect from freezing on page 31.

CAUTION: Please read and comply with the following guides to prevent damage to the sof-

tener or other property, personal injury, or possible fatal shock.

This softener works on 24 volts only. Be sure to use only the transformer included.

Plug it into a nominal 120V, 60 cycle household outlet that is grounded and properly

protected by an overcurrent device such as a circuit breaker or fuse. If transformer is

replaced, use only the authorized service Class II, 24 volt, 10 VA transformer.

• Unplug the transformer right away if the power cable should become damaged or frayed.

Make repairs, or replace the transformer, before plugging back into the power outlet.

• Always unplug the softener from electrical power before removing outer valve covers.

• This system is not intended to be used for treating water that is microbiologically unsafe or of

unknown quality without adequate disinfection before or after the system.

* The capacity to reduce clear water iron is substantiated by WQA test data.

European Directive 2002/96/EC requires all electrical and electronic equipment to

be disposed of according to Waste Electrical and Electronic Equipment (WEEE)

requirements. This directive or similar laws are in place nationally and can vary

from region to region. Please refer to your state and local laws for proper disposal

of this equipment.

4

Questions? Call The Kenmore Water Line 1-800-426-9345

INSPECT SHIPMENT

Your water softener is shipped complete in one carton.

Use care when handling the softener. DO NOT turn

upside down. DO NOT drop, or set on sharp objects that

could make a hole in the bottom. The water softener is

heavy, do not try to lift it or move more than is necessary.

Remove all items from your shipping carton.

Check all items against the packing list below. Note any

items lost or damaged in shipment.

Note any damage to the shipping carton. Refer to the

exploded view and parts list in the back of the manual for

the part names and numbers of missing or damaged

items.

Contact the store where purchased if problems exist.

PARTS DESCRIPTIONS SMALL PARTS

Salt

Storac

Tank

Resin

Salt Hole

Cover

(Open)X',_

Nozzle Valve

Assembly Assembly

Face

Plate [ owner's manual ]

Cover

Brinewell

Cover [ j

Brinewell

Installation

Adaptors (2)

Clips (4) @

O

Drain Tubing

Bypass Valve

Brine Valve

Ground Clamp Kit

Grommet

4_ Tube Clamp

J

Tube Adaptor

_>._ Tube Clamp

FIG. 1

Questions? Call The Kenmore Water Line 1-800-426-9345

PLAN YOUR INSTALLATION

It is recommended to read through the entire manual before

beginning your installation. Follow all steps exactly. Reading this

manual will also help you get all the benefits from your system.

TOOLS NEEDED:

• Safety glasses

• Flathead screw driver

• Phillips screw driver

• Adjustable slip joint pliers

• Tape measure or ruler

J

Flathead Screwdriver

Safety Glasses Phillips Screwdriver Adjustable Slip Joint Pliers Tape Measure or Ruler

ADDITIONAL TOOLS NEEDED FOR THE FOLLOWING INSTALLATIONS:

SOLDERED COPPER

• Tubing Cutter

• Propane Torch

• Solid Core LEADFREE Solder

• Paste Flux

• Emery Cloth

or Sandpaper

THREADED PIPE

• Hacksaw or Pipe Cutter

• Pipe Wrenches

• Pipe Threading Tool

• Pipe Joint Compound approved

for use on potable water

CPVC OR PVC PLASTIC

• Hacksaw

• Adjustable Wrench

• Primer and Solvent Cement

approved for use on potable water-

THE PROPER ORDER TO INSTALL WATER TREATING EQUIPMENT

(Shows sequence of equipment only. Seldom, if ever, would all items be needed.)

Sediment or Taste &

Odor Cartridge Filter

Cold, soft water

Hot, soft water

Heater L, _

Kitchen or Bathroom City Water Supply

Cold Faucet

Water *Taste & Iron Neutralizer Clarifying

Softener Odor Filter Filter Filter

OR

• Always place an Iron Filter UPSTREAM of the water softener.

• Always place a Neutralizer UPSTREAM of an Iron Filter, etc., as shown.

* Place a Taste & Odor Filter UPSTREAM of a water softener on a chlorinated water supply

and DOWNSTREAM of a water softener on a non-chlorinated water supply.

Hard Water to _ D_

o deFa ce s

_ _ WeIt Water Supply I

Pressure or Dispensing

Captive Air System I

Tank [

I I I _ I [ Sediment

[ I [ _ _ _ [ [ I Cartridge Filter |

j LI U Ll U !

Welt Water

FIG. 2

Questions? Call The Kenmore Water Line 1-800-426-9345

6

shutoff

valve

FIG. 3

Typical Installation

WHERE TO INSTALL THE WATER SOFTENER

Review the following points before you choose a place to put your softener.

1. Place as close as possible but always after, the

pressure tank (well water) or water meter (city

water). See Fig. 3.

2. Place as close as possible to a water drain such as

a floor drain, laundry tub, sump or standpipe. See

Fig. 3.

3. Connect to the house main water pipe BEFORE

THE WATER HEATER. See Fig. 3. Temperature of

water going through the softener must not be

more than 120°F (49°C). Hot water will damage

inner softener parts. To reduce the risk of hot water

backup, piping between the softener and water

heater should be as long of a run as possible.

4. Keep outside faucets on hard water to save soft

water and salt. See Fig. 3.

5. Do not install in a place where the softener could

freeze. Damage caused by freezing voids the war-

ranty by Sears Brands Management Corporation.

6. Put the softener in a place where water damage is

least likely to occur if it develops a leak. Sears or

the manufacturer will not repair or pay for water

damage.

7. A grounded, 120V electrical outlet is needed within

10 feet of the softener. See Fig. 3. This is to plug in

the transformer. The softener has a 10 foot power

cable. Be sure the outlet and transformer are in

an inside place, to protect from wet weather. Use

a continuously "live" outlet, which cannot be acci-

dentally switched off.

8. When installing in an outside location, you must take

the steps necessary to assure the softener, installa-

tion plumbing, and wiring, are protected from the

elements, direct sunlight, contamination, vandalism,

etc.

Questions? Call The Kenmore Water Line 1-800-426-9345

Plug the softener transformer

into an inside, 120 volt 60Hz

electrical outlet. If an outside

outlet is used, be sure it has

approved weather protection.

Suggested Slab Foundation Installation

WATER SOFTENER

(install in garage, car port,

or other sheltered area)

water heater

kitchen

r_q bathroom

outside I _L_ I I I

.,o. II I1 -°

lJ I

J _ oo°°

"-," bypass

valve outside

-soft

Run drain tubing to laundry tub or

p-trap inside home, if possible.

Otherwise, run to a dry well.

outside

- hard

outside

- hard

water in

For outside hard

water, trench under-

ground as needed.

FIG. 4

DRAW IN YOUR PIPES

AND FITTINGS

Draw the plans for your "IN" and "OUT"

piping here. Include all pipe, fittings and

accessories you will use.

Make a list of all materials you will need

and buy them before you begin to install

the water softener.

120V - 60Hz

U

Electrical

Outlet

Left

Valve Outlet Side

Valve Inlet

Your House Main Water Pipe

Right

* In what direction does the water flow?

Be sure to plan "IN" and "OUT" piping so water

flow is to the softener valve inlet. Plan a

crossover if flow is from left to right.

Raw

CROSS-OVER

Main Water Pipe

Outlet

Soft Water

To Water Softener

FIG. 5

Questions? Call The Kenmore Water Line 1-800-426-9345

8

PIPE,FITTINGS,OTHER MATERIALS NEEDED

You must first decide how to run "in" and "out" pipes to

the softener. Look at your house main water pipe at the

point you will connect the softener. Is the pipe soldered

copper, glued plastic, or threaded galvanized or brass?

What is the pipe size? What kind of pipe and fittings is it

easiest for you to work with, and what tools do you have?

Now look at the common plans for "in" and "out" piping

on soldered copper. See Fig. 6. Use it as a guide to plan

what materials you will need. Get all the materials you

will need before you start.

Use Fig. 5 to make a plan drawing for your specific

installation. "In" and "out" fittings included with the soften-

er are 1" NPT threaded adaptors. You should maintain

the same, or larger, pipe size as the water supply pipe,

up to the softener inlet and outlet. Use copper, brass,

galvanized or PVC plastic pipe and fittings for the "in"

and "out" pipes. Be sure to check local codes.

Note: If converting from galvanized to copper pipe

use approved dielectric insulating connectors.

ALWAYS install the bypass valve (that is included with

the unit) or a three valve bypass. See Fig. 9 to13.

Bypass valves let you turn off water to the softener if

needed for repairs, but still have water in the house

pipes.

Drain tubing (3/8" inside diameter), is needed for the

valve and salt tank drains. See Fig. 16. If a rigid valve

drain is needed to comply with plumbing codes, you can

buy the parts needed (see Fig. 16) to change the soften-

er to a 1/2 inch minimum copper tubing drain.

OUT IN

1" NPT sweat

adaptor (2)*

-1/

Use teflon tape,

pipe joint compound ,,.

or both. _ [_ 1" NPT

_L'" adaptor t 2 of each

_ _ _ included

clip

ass Valve

Valve

Inlet

Use teflon tape,

pipe joint compound

or both.

1" NPT sweat

adaptor (2)*

Valve

Inlet

OUT IN

1" NPT clip

adaptor /

_/ 2 of each

included

FIG. 6

*NOTE:

For plumbing connection, buy 2 sweat adaptors and plumb

directly to the inlet - outlet adaptors. Threads on the inlet - outlet

adaptors are 1" NPT.

CAUTION:

DO ALL SOLDERING BEFORE CONNECTING SWEAT ADAP-

TORS TO INLET-OUTLET ADAPTORS OR BYPASS VALVE.

Questions? Call The Kenmore Water Line 1-800-426-9345

BEFORE INSTALLING CHECKS & TESTS

Your water supply needs to be checked for chemical

analysis, water pressure and water flow rate. To accom-

plish this, complete the following steps:

Check Water's Chemical Analysis: Sears sells a com-

plete line of water treating equipment to correct various

water problems. To be sure you have the proper type

and size equipment, You must have your water tested.

Your Sears store can give you a water test results for

hardness, iron and acidity, and tell you what equipment

you need. Simply take at least a 4 oz. sample of your

water to Sears, and they will test it while you wait. If you

need help to get your water tested, or if you have other

questions about your water, ask at your Sears store.

NOTE: Add these readings to the Facts and Figure

table on page 3.

Check Your Water Pressure: For your softener to work

right, a water pressure of no lower than 20 pounds per

square inch (psi) is needed in the house water pipes.

The highest pressure allowed in the water pipes is 125

psi. If pressure is over 125 psi, buy and install a pres-

sure reducing valve in the water inlet pipe to the soften-

er.

NOTE: If water pressure during the day is 100 psi or

more, pressure during the night may go over 125 psL

Adding a pressure reducing valve may reduce the

flow.

NOTE: Add these readings to the Facts and Figure

table on page 3.

If you have a well water system, look at the pressure

gauge to find the water pressure. Call your local water

department if you have city water. They will tell you what

the water pressure is where you live.

NOTE: Add these readings to the Facts and Figure

table on page 3.

Check your water flow rate: A water flow of at least 3

gallons per minute is needed. A lower flow will keep your

softener from working as well as it should. Complete the

following steps to make an easy check of your flow rate.

1. Fully open two cold water faucets close to the point

water enters the house.

2. With both faucets open, fill a gallon container at one

faucet while looking at a watch or clock to see how

many seconds it takes.

3. Empty the container and go to the second faucet (be

sure BOTH faucets are still on). Fillthe gallon container

at the second faucet and see how many seconds it

takes.

4. Turn off both faucets. Now add the number of seconds

it took to fill the container at both faucets.

5. A total of 90 seconds, or less, means the system flow

rate is good.

NOTE: Add these readings to the Facts and Figure

table on page 3.

NOTE: Codes in the state of Massachusetts require

installation by a licensed plumber. For installation,

use plumbing code 248CMR of the Commonwealth

of Massachusetts.

Questions? Call The Kenmore Water Line 1-800-426-9345

10

ASSEMBLE INLET OUTLET ADAPTORS,

OR SINGLE BYPASS VALVE

Complete the following steps to assemble the adaptors or

bypass valve.

1. Close the shutoff valve on the house main water pipe,

near the water meter or pressure tank, to turn off the

water. See Fig. 7.

2. Shut off the gas or electric supply to the water heater.

See Fig. 7.

3. Open the highest and lowest water faucets in your

house. This will let water drain from the pipes. Close

faucets after water has drained.

4. Remove the main cover. Remove the salt hole cover

first and then pull outward on the two tabs to release

main cover. See Fig. 8.

Set both covers aside so they will not get scratched or bro-

ken.

INSTALL SEARS BYPASS VALVE AND / OR THE

INLET OUTLET THREADED ADAPTORS

NOTE: If you will not install the bypass valve because

you will have a three (3) valve bypass, skip steps 6 &

7, but do steps 5 and 8.

5. Visually check and remove any foreign materials from

the valve inlet and outlet ports. See Fig. 9. Carefully

remove the two large plastic clips (you will use them).

Check to be sure the turbine and turbine support are

firmly in place. See Fig. 10.

Shutoff Shutoff . Pressure

Valve Valve ,z/ Tank

Pump

Electrical

Panel

FIG. 7

Salt Hole Cover

Cover (Main)

/

//

,/

/

FIG. 8

BYPASS VALVE:

6. Put a light coating of silicone grease on the o-ring seals

and slide onto the bypass valve.

7. Push the bypass valve into the softener valve as far as it

will go. Snap the two large holding clips into place,

from the top down as shown. See Fig. 11.

CAUTION: Be sure the clips snap firmly into place so

the bypass valve will not pull out. See Fig. 11.

INLET AND OUTLET THREADED ADAPTORS:

8. Put a light coating of silicone grease on the o-ring seals

and slide into the threaded adaptors. Push the adaptors

into the valve inlet and outlet ports, or bypass valve

ports, as far as they will go. Both adaptors are the same

and fit either port. Snap the two large holding clips

into place, as shown. See Fig. 11.

CAUTION: Be sure the clips snap firmly into place so

the tubes will not pull out. See Fig. 11.

INSTALLING BYPASS VALVE, AND/OR

INLET AND OUTLET THREADED ADAPTORS

jClip (2)

Valve Outlet

Included with

Softener

Valve Inlet

Included with

Softener

FIG. 9

Questions? Call The Kenmore Water Line 1-800-426-9345

11

Before installing the bypass valve, or

copper tube, be sure the turbine and

support are firmly in place in the

valve outlet port.

Turbine

Support Sensor Port

H/I

Turbine

FIG. 10

INSTALLING HOLDING CLIPS

Bypass Valve or

Installation Adaptor

Black Cli Cross Section of Valve

Inlet or Outlet

Clip Sna)s into Place

Between Larger Diameter Rings

O-Ring

FIG. 11

BYPASS VALVE TURNED DOWNWARD

Turn bypass valve upside

down to connect to floor

level plumbing.

IN

OUT

FIG. 12

INSTALLING 3 VALVE BYPASS AND PIPES

Complete the following steps to install the three (3)

valve bypass:

• Cut the house main water pipe where you will con-

nect the softener.

• Loosely put together pipe, fittings, and the three

(3) valves.

• Place valve(s) within easy reach.

When all pipe, fittings and valves make a good fit

together, tighten all threaded joints (use pipe dope

on outside threads), or solder all sweat joints.

3 VALVE BYPASS

TO FIG. 13

Softener Inlet

Questions? Call The Kenmore Water Line 1-800-426-9345

12

POSITION SOFTENER INTO PLACE

Complete the following steps to position the softener.

1. Grip under the ridge on the salt tank sidewall.

2. Carefully rock back and forth into position.

3. Move the softener into position.

4. Place on a level and smooth surface. If needed, put a

piece of 3/4" plywood, at least 17" x 20", under the

tank. Then put spacers under the plywood to level the

softener. See Fig. 14.

NOTE: Do not put shims or spacers directly under

the tank, without the plywood. The weight of the sof-

tener, when full of salt and water, may cause the tank

to puncture or break at the shim or spacer.

CONNECT THE SOFTENER

Refer to your plan drawing. See Fig. 5.

Measure, cut (thread if needed) and put all pipe and fit-

tings together up to the main water pipe, or to the

bypass valve(s) you installed in the previous step.

CAUTION: Never solder fittings while connected to

nonmetallic parts. Wait until soldered pipe has

cooled before connection. See Fig. 15.

CAUTION: Be careful when putting pipe fittings

together. Do not cross thread, and do not overtight-

en.

MOVE SOFTENER INTO PLACE

Grip under ridge

to move softener.

Plywo_

Shims

FIG. 14

TYPICAL SOLDERING

CONNECTIONS

ain Water Pipe

4. Solder

NOTE: To be certain heat will

not travel down the pipe and

into the bypass valve (or

installation adaptors), wrap

the bottom of the pipe and the

bypass valve in a wet rag.

Hard Water

1. Cut pipe to

correct length.

2. Solder (WHEN

COOL, do Step 3).

3. Put threaded adaptor

into bypass valve

port.

FIG. 15

Questions.'? Call The Kenmore Water Line 1-800-426-9345

13

CONNECT THE VALVE DRAIN HOSE

Take a length of 3/8" inside diameter drain tubing and

attach one end to the drain fitting. See Fig. 16. Use a

tube clamp to hold it in place. Put the other end of the

tubing over a floor drain, into a laundry tub, standpipe,

or other suitable drain. Check your local codes.

Leave an air gap of about 1-1/2" between the end of

the hose and the drain. This gap is needed so you

don't get a backflow of sewer water into the softener.

Do not put the end of the hose into the drain or con-

nect without the air gap.

Place and support the hose so it does not kink or have

sharp bends. Secure the hose end so water pressure

does not cause the hose to "whip". Tie or wire it in

place. Do not pinch the hose shut. The softener will

not work if this drain hose is pinched, plugged,

closed or restricted in any way. Direct drain flow

down into drain from drain line as flow could possibly

over shoot the drain cover.

Keep the hose lower than the drain fitting. In some

homes, to get to a drain you must raise the hose and

run it overhead. If you need an overhead drain, do not

raise the hose more than 8' above the floor. A copper

drain tube is best to use.

COPPER DRAIN TUBE: Local plumbing codes may

require the use a copper valve drain tube. A copper

tube is also best to use for an overhead drain. Use a

copper drain tube if the softener is installed outside, or

in the sunlight. Heat from the sun can soften, flatten

and close up some kinds of tubes.

To adapt a copper drain tube to the softener, buy a

compression fitting (1/4" female pipe threads x 1/2"

O.D. tube) and tubing from your local hardware store.

CONNECT SALT TANK OVERFLOW TUBING

1. Locate the rubber grommet, tube adaptor and tube

clamp (see Fig. 16) that are in the parts bag.

2. Push the grommet into the hole in the salt tank wall

so half is inside and half is outside.

3. Push the bigger end of the tube adaptor into the

grommet.

4. Push one end of a length of 3/8" I.D. tubing onto the

tube adaptor, using the tube clamp to hold it in

place.

5. Put the other end of the tubing over the floor drain.

IMPORTANT: Overflow water must run downward

through the tubing. Do not raise the tubing higher

than the grommet and tube adaptor. See Fig. 16.

IMPORTANT: Do not connect to the valve drain

hose you installed in step 1. Both drains must

have a separate hose or tube.

NOTE: Overflow drain tubing is available from

Sears. See parts list in back of manual.

Grommet Tube

_, Adapto_

NOTE: Overflow 1

drain tubing is avail- \

able from Sears,

Item No. 42-3433 _'-...

(20 ft). ------_-

Overflow Drain Tubing ___

1/4 NPT Threads

Barbs

Clip

Cut Barbs from Drain

Fitting (Pull clip and

emove fitting from valve.)

Comp Fitting. 1/4 NPT

1/2 in. O.D. Tube

(Not furnished)

\\

\\ To drain

N\

\\ point other

\" than floor

\\

"_-, drain.

Valve Drain Hose "-_Support

tubing in

place as

needed.

Tie or Wire 1-1/2"

Tubing in Place Air G p

FLOOR DRAIN

STANDPIPE

Gap

1/2" Outside Diameter

Copper Tube

(Not furnished)

FIG. 16

Questions? Call The Kenmore Water Line 1-800-426-9345

14

LEAK TEST

To check for leaks, complete the following steps:

CAUTION: To avoid water or air pressure dam-

age to softener inner parts, and to flush pipe

chips or other residue from the water pipes, be

sure to do the following steps exactly as

instructed.

1. Fully open two cold, soft water faucets near the

softener.

2. Look at the pictures in Fig. 18 and 19 to deter-

mine your kind of bypass valve(s). Place bypass

valve(s) in "bypass" position. On a single valve,

slide the stem inward to bypass. On a three (3)

valve system, close the inlet and outlet valves and

open the bypass valve.

3. Fully open the house main water pipe shutoff

valve. Observe steady water flow from both open

faucets.

4. Place bypass valve(s) in SERVICE EXACTLY as

follows: Keep soft water faucets open.

a. Single Bypass Valve: Slowly, slide pull the

valve stem outward toward service, pausing sev-

eral times to allow the softener to pressurize slow-

ly.

b. Three Valve Bypass: Fully close the bypass

valve and open the outlet valve. Slowly, open the

inlet valve, pausing several times to allow the sof-

tener to pressurize slowly.

5. After about three minutes, open a hot water

faucet for about one minute, or until all air is

expelled, then close.

6. Close both cold water faucets.

7. Check your plumbing work for leaks and fix right

away if any are found. Be sure to observe previ-

ous caution notes.

NOTE: If this procedure is performed on a new

softener, water coming from the taps may initial-

ly be discolored. This normally occurs the first

time water runs through the resin bed. The dis-

colored water is not harmful, and the discol-

oration will not last more than a few minutes.

HOUSE MAIN WATER

SHUTOFF VALVES

Shu_

Water ¢--_% Pressure Tank

Meter Shutoff Valve_ / d"-

Well Pump

FIG. 17

SINGLE BYPASS

Pull Stem Outward

For Service

Push Inward

For Bypass

Note: Stem may be installed

in either direction. The end

with writing should be pulled

out for service position.

FIG. 18

FOR SERVICE

Close bypass valve.

Open inlet & outlet

valves.

FOR BYPASS

Open bypass valve.

Close inlet & outlet

valves.

VALVE BYPASS

Outlet

Valve

/pass

Valve

Inlet

Valve

FIG. 19

Questions? Call The Kenmore Water Line 1-800-426-9345

15

INSTALLGROUNDINGCLAMPBETWEEN

THESOFTENERINAND OUT PIPES

The house cold water pipe (iron or copper) is often

used to ground all electrical outlets in the home.

Outlets are grounded to protect you from shock when

you touch any electric appliance plugged into the out-

let. If you installed the single bypass valve, the cold

water pipe ground is broken. See Fig. 20 and 21.

IMPORTANT: Be sure the cold water pipe has

direct metal to metal contact all the way to the

ground. Plastic, rubber or other electrically insulat-

ing parts such as hoses, fittings, washers or gas-

kets can break the direct metal to metal contact.

Also check the water meter (city water) or the well

pump. Install #4 copper jumper wires, clamped

tightly on both ends, across insulated parts. See

Fig. 21.

To restore the ground, take the ground clamp kit that is

in the parts bag. Install across the inlet and outlet cop-

per tubes. See Fig. 20. Be sure good contact is made

between the pipe and the clamps.

ELECTRICAL POWER OUTLET FOR

YOUR SOFTENER

The softener works on 24 volt, 60 Hz electric power.

The included transformer changes standard 120 volt

AC house power to 24 volts. You must plug the trans-

former into a grounded, 120 volt outlet only. Be sure

the outlet is always "live" so someone cannot turn it off

by mistake. See Fig. 22.

NOTE: The included transformer is made for inside

use only. Be sure the electrical outlet you plug the

transformer into is inside, to protect from weather.

PLUG IN THE TRANSFORMER

Plug the transformer into the electrical outlet.

COLD WATER PIPE GROUNDING

Ground

Clamp (2)'_

Screw with lock j

washer and nut

TO

Valve Inlet

FROM

Valve Outlet

FIG. 20

WATER METER JUMPER WIRE

Water Meter

#4 Groundwire

FIG. 21

CONNECTING TRANSFORMER

Transformer

120V-60Hz

Electrical

Outlet

Power Cable

_ From Face Plate-Timer

FIG. 22

Questions? Call The Kenmore Water Line 1-800-426-9345

16

INSTALL COVERS

After installing your water softener, replace the covers.

Angle the covers so the main cover clips onto the back

first, then bring down in front and clip on the two (2) tabs

inside the rim of the salt hole and lower the salt cover

closed. See Fig. 23.

RESTART THE WATER HEATER

Turn on the gas (or electric) supply to the water heater

and light the pilot.

YOUR PLUMBING INSTALLATION AND ELECTRICAL

WORK ARE NOW COMPLETE.

Salt Hole

Cover

INSTALL COVERS

Cover

r./(Main)

\

,/

y

/

FIG. 23

Questions? Call The Kenmore Water Line 1-800-426-9345

17

Display UP Button

REGENERATION Button

SELECT Button

DOWN Button

FIG. 24

PROGRAM THE TIMER

1. When the transformer is plugged in, a model code

(S 25) and a test number (example: J1.1) show in the

face plate. This will display for four (4) seconds. Then,

12:00 PM and the words SET TIME begin to flash.

NOTE: If "- - - -" shows in the display, press the

UP or DOWN button until S 25 shows in the dis-

play. Then, press the SELECT button to set, and

change to the flashing SET TIME display.

2. To check the model code, unplug the transformer at

the wall outlet and plug in again. If other than S 25

shows, refer to the Troubleshooting Section.

SOUND "BEEPER": A "beeper" sounds while press-

ing buttons for timer setup. One beep signals a

change in the face plate display. Repeated beeps

mean the timer will not accept a change from the but-

ton you have pressed, telling you to use another but-

ton. For example, while setting the hardness, the

beeper sounds repeatedly when the display reaches 1

using the DOWN button, or the highest hardness set-

ting using the UP button.

CODE1

S c:,l

ISET I

T,ME_ _--I't--I1--t

L- .L! L! pM

FIG. 25

SET PRESENT TIME OF DAY

If the words SET TIME do not show in the display, press

the SELECT button until they do show in the display.

Press the UP or DOWN buttons to set the present time.

Press UP to move the display ahead; press DOWN to

move the time backward. If the present time is between

noon and midnight, be sure PM shows. If the present

time is between midnight and noon, be sure AM shows.

Each press of the UP or DOWN buttons changes the

time by one (1) minute. Holding the buttons in changes

the time 32 minutes each second.

SET I

i I,[ I_-t

I "riME

-i.-! 0 pM

t t.-IL-

! !._-i0

FIG. 26

Questions? Call The Kenmore Water Line 1-800-426-9345

18

SET WATER HARDNESS NUMBER

To set the water hardness number, complete the follow-

ing steps:

1. Press the SELECT button once to display the words

SET HARDNESS and a flashing 25. The grains per

gallon (gpg) hardness of your water supply is on your

water analysis report. Be sure to enter water test

results on the Facts & Figure Chart on page 3.

2. If your water supply contains iron, compensate for it

by adding to the water hardness number. For exam-

ple, assume your water is 20 gpg hard and contains

2 ppm iron. Add 5 to the hardness number for each I

ppm of iron. In this example, you would use 30 for

your hardness number.

2ppmironx5= 10

20 gpg hardness

+10

30 HARDNESS NUMBER

3. Press the UP or DOWN buttons to set your water

hardness number in the display. The DOWN button

moves the display to 1. The UP button moves the

display to the highest setting (see maximum setting

for your model in the specifications).

NOTE: Each press of the UP or DOWN button

changes the display by 1 between 1 and 25.

Between 25 and the highest number, the display

changes 5 at a time (25, 30, 35, etc.) Holding the

UP or DOWN button in changes the display twice

each second.

SET REGENERATION TIME

To complete setting the regeneration time, complete the

following steps:

1. Press the SELECT button to display the words SET

RECHARGE TIME and a flashing 2:00 AM.

2. At the 2:00 AM recharge time setting, the softener

begins regeneration (see pages 25 - 27) at 2:00 AM.

This is a good time in most households because

water is not being used. If a different recharge time

setting would be better for your household, complete

the following step.

3. Press the UP or DOWN buttons to set the desired

recharge starting hour. Be sure to observe the AM-

PM as you did when setting the present time of day.

Note: Each press of the UP or DOWN buttons

changes the display one hour. Holding the but-

tons in changes the display twice each second.

SET SALT LEVEL

To set the salt level, complete the following steps:

1. Press the SELECT button to display SET SALT

LEVEL and a flashing 0 (zero). See page 21, for

instructions on adding salt to the salt storage tank.

The face plate timer has a salt monitor with an indi-

cator light to remind you to add salt to the storage

tank.

NOTE:You must set salt level each time salt is

added to the water softener.

2. To set this monitor system, lift the salt hole cover

and level the salt in the storage tank. The salt level

decal, on the brinewell inside the tank, has numbers

from 0 to 8. Observe the highest number the leveled

salt is at, or closest to. Press the UP or DOWN but-

tons until the number corresponds with the salt level

number. At level 2 or below, the indicator LED will

flash. If you wish to turn this feature off, press the

DOWN button past 0, and the word "OFF" flashes in

the display.

3. Press the SELECT button once again, to complete

initial programming, and the current time of day will

show in the display.

SET HARDNESS

71-_

C7

T,ME _7"t717

C.UU _"

SETSALTLEVEL

0

LT.TL- 1

7.CO

FIG. 27

Questions? Call The Kenmore Water Line 1-800-426-9345

19

SANITIZE THE WATER SOFTENER

Care is taken at the factory to keep your water softener clean

and sanitary. Materials used to make the softener will not

infect or contaminate your water supply, or cause bacteria to

form or grow. However, during shipping, storage, installing

and operating, bacteria could get into the softener.

SANITIZE YOUR WATER SOFTENER AS FOLLOWS:

1. Be certain the bypass valve is pulled out to

"service" position.

2. Liftthe salt hole cover and using a pail add up to 3 gallons

of water to the salt storage tank.

3. Remove the brine well cover (Fig. 28) and pour about 3/4

ounce, or 1 to 2 tablespoons, of common 5.25% 1,unscent-

ed, household bleach (Clorox, Linco, BoPeep, White Sail,

Eagle, etc.) in the softener brinewell. Replace the brinewell

cover.

4. Press the REGENERATION button and hold for 3 seconds

to start a recharge. This first recharge does several things.

• It draws the bleach into and through the softener to sani-

tize it.

• It fills the salt tank to the water level needed.

• It gets all the air out of the resin tank.

• It prepares the resin bed (see page 25) for service and

flushes residual chlorine from the softener.

NOTE: This recharge takes about 2-1/2 to 2-3/4 hours,

depending on the salt type setting.

NOTE: During a recharge the water softener bypasses

raw water to the home. You will not get salty water or

affect the regeneration cycle if water is used at this time.

You can sanitize the softener with or without salt in the

storage tank.

1Recommended by the Water Quality Association.

On some water supplies, the water softener may need peri-

odic disinfecting.

Your new Sears softener is now softening the water for your

household needs. However, your WATER HEATER is filled

with hard water. To have fully soft water right away, you can

drain the water heater so it refills with soft water. If you don't

drain the water heater, it will take a few days before you have

fully soft water.

To drain the water heater, open a hot water faucet and let it

run until the water runs cold. Then close the faucet.

NOTE: If this procedure is performed on a new softener,

water coming from the taps may initially be discolored.

This normally occurs the first time water runs through

the resin bed. The discolored water is not harmful, and

the discoloration will not last more than a few minutes.

Water

About 3 gallons

Salt Hole Cover

/2 /Brinewell Cover

(Remove and

/ add about

3/4 oz. bleach)

/

f Brinewell

/

FIG. 28

Questions? Call The Kenmore Water Line 1-800-426-9345

20

Page is loading ...

Kenmore 625.38306 User manual

This manual is also suitable for

Kenmore 625.38306 User manual

Related papers

Other documents