S'o, _A/RS
OWNER'S MANUAL
Universal Remote Control
Converter Kit
Model 139.53755 SRT ('With I Remote Control)
Model 139.53756 SRT (With 2 Remote Controls)
NOTICE TO U. S. CONSUMERS:
Some states prohibit the selvice or repair of garage door
openers whch cannot be made to comptywith the safety
standards contained in UL 325 (1988 revision). In order
to complywith boththe letterand the spidtof these laws,
this universal remote control converter kit should not be
used with any Sears Craftsman® garage door opener
manufactured pdortoApril 1, 1982.
UNIVERSAL REMOTE CONTROLS consist ofa receiver
and remotecontrol(s),The remotecontrolsends a coded
signalfrom outside the garage. Inside the garage, the plug-
in receiveraccepts the transmitted signal and startsthe
dooropener.
IMPORTANT: Disable your existing recaiv_ before
Installing this replacement unit. if thta Is not possible,
Io_lte re<_vm" mDfar fi"omoriglrlmlnvcelv_ as ix_ldble.
When Imltelllng two or more re_dvere In a gerege,
poeition them at least 10 feet apart to prevent etastronlc
WARNING
i i i i
CNldran opemlthg or pkqdngwith a gar=gedcor opener
santhJurethenamlvneor olher&77_eBsra_eOborcou/d
dow xsd cacaesmfous/njuryordesth.
Inetdlther=_u (oranyediMIo.l pu¢ I:_lons) out
¢f thema_ of_l_rco end awayfromal movtBgparte
ofthe doorand doorhardware,bin"m _beBlrags
donr/sz,t_e. Donmsnowcldldrente oplr_e _ pcah
bumca(s)ortheremoteonn_ol(s).
A moving_w'mgedcorom_d/njum Bomcone_er/t.
/_tfvete the openeronly wizenthe door 18prol_rly
adjusted, you can see It clearly, and there are no
_ to doortbrav_.
Oiasoen_-'tpowerto the garagedoor openerbefore
procsad_g.
To comply with FCC rules, adjtmtmentsor medifica_or_ of this
receiver and/or transmitterare prohibited,except for changingthe
code setting or repladng the batte_. 3HERE ARE NO OTHER
USER SERVICEABLE PARTS,
OPENER RECENER: Inseda smallscrewdriverinsk:)ton
receiverfrontpenal as shown.Twistupactuatorcover.
CONNECT RECEIVER AND OPENER: Remove about1/4"of
insulationfromeash ond of the 2-strandbsilwire.Connestone
end to the racaiver screw_ (polarityisNOT required).
Routawire ainngtheohannels and outthe boftomes shown.
Cannectthe othereed of the ballwiretothe twoogener
terminalscrewslabeled"whiteand red', "commonand
command"or the terminalsuesdforthe peshbuitoncontrd.
Use insulatedstaples(notsupplied)tosecurebellwire
betweenrecalver and oponer.Leng_ of bellwiredepandaon
wherethe meek,or willbe instaJled.Replecethe actualdrcove_.
Choosea 120Ves polarizedoust forthe receivervAdchis
OUT OF THE REACH OF CHILDREN. Plug reselvm"Into
sek_'t_l oull_. Rotum power to the opener.
Actuator Cover
Power Indicator Light
J
Terminals
Indk:_dor
Light
BertW_ts
_Channe_s
Connect BellWire
To Garage Door
Opener Terminals
I
BellWire
The receiver and remote control(s) have been factory
preset with a matching code. THE REMOTE
CONTROL(S) OPERATES FROM THE LARGE PUSH
BUTTON. You can salivate your opener wllh =s many
ac four'SRT" remote controls and one Km/tau Entry.
Ifyou purchaseaddilional remote controls tooperate this
receiver:
1) Remove the receiver actuatorcover.
2) Press and HOLD the selected inmate control push button
(IllustrationA).
3) Than press the "SRT"actuatoron the receiver
(illustration B). The adjacent indicator light willFLASH.
Release the remote controlpush button.
The opener will nowoperate when either the receiver
actuatoror theremotecontrolpush buttonispressed.
NOTE: If the remote control push button Is not he_d
down until the receiver Indicator Itghtflashes, the
rtmelver will not tsem the code.
Toerase ALL r_note oontroi ood_ from memory:
Pnras an¢lHOLD receiv_r .'SRT"ao_uafu_.Indicator
I/ght aiongs/d_ wi/I glo_ When b_eind/cator /lght tums
OFF (In aboutS secon_) AU. code_ wlll be enme_
A 3-Furm_o_ Remote Control
Select a remote co_tro_push
buttonto operate receiver
I REPLACEMENT PARTS: Remote ControlHousing Only(no circuitboard) 41A3888; Visor clip29C128; Batteryo10A14;
I
Universal Receiver (cornp_ete)41A41S1; Receiver ActuatorCover- 41A3591 I
01994, SearsRoebuckand Company
114A1457B All RightsReserved Printedin Mexico
/
