GE Webcam BECCO2200 User manual

g

GE Energy Service

s

Document Number : A164-0CG

Version : 1.00

Revision : 2

Date : 02.08.23

Classification: Restricted Full

BECCO2200 DCA

Configuration Guide

GE Energy Services

BECCO2200 DCA

Configuration Guide

A164-0CG-1.00-2 Restricted

ii

Full

NOTICE OF COPYRIGHT & PROPRIETARY RIGHTS

The contents of this manual are the property of General Electric Canada Inc. No part of this work

may be reproduced or transmitted in any form or by any means, except as permitted in written

license agreement with General Electric Canada Inc. The information contained in this document

is subject to change without notice.

Any attached hardware schematics and technical descriptions, or software listings that disclose

source code, are for information purposes only. Reproduction in whole or in part to create working

hardware or software for other than General Electric Canada Inc. products is strictly prohibited,

except as permitted by written license agreement with General Electric Canada Inc.

TRADEMARK NOTICES

GE and g are trademarks and service marks of General Electric Company.

WESDAC is a registered trademark of General Electric Company, General Electric Canada Inc. All

other brand and product names mentioned in this document are trademarks or registered

trademarks of their respective companies.

BECCO2200 DCA

Configuration Guide

GE Energy Services

Restricted A164-0CG-1.00-2

Full

iii

Table of Contents

About this Guide

Purpose of this Guide.................................................................................................................xi

Who Should Use this Guide.......................................................................................................xi

Additional Documentation........................................................................................................xii

How this Guide is Organized...................................................................................................xiii

Overview

Chapter 1: Configuration Tables

1.1 BECO2200 DCA Configuration Tables..........................................................................1

1.2 Configuration Sequence..................................................................................................2

Chapter 2: Configuring Win for the BECO2200 DCA

2.1 WESDAC Point Allocation.............................................................................................3

2.1.1 Binary Inputs...............................................................................................................4

2.1.2 Binary Outputs ............................................................................................................4

2.1.3 Counters ......................................................................................................................4

2.1.4 Analog Inputs..............................................................................................................4

2.1.5 Analog Outputs ...........................................................................................................4

2.1.6 Device Status...............................................................................................................4

Chapter 3: Configuring the A164APPL Table

3.1 General Information........................................................................................................5

3.2 Description of Fields.......................................................................................................5

3.2.1 DCA Index ..................................................................................................................6

3.2.2 Reply Buffer Size Adjustment ....................................................................................6

3.2.3 SOE Buffer Size Adjustment ......................................................................................6

3.2.4 SOE Buffer Overflow Option .....................................................................................6

GE Energy Services

BECCO2200 DCA

Configuration Guide

A164-0CG-1.00-2 Restricted

iv

Full

3.2.5 Device Event Response Time .....................................................................................7

Chapter 4: Configuring the A164PORT Table

4.1 General Information........................................................................................................9

4.2 Description of Fields.......................................................................................................9

4.2.1 Communication Port Name.......................................................................................10

4.2.2 Communication Port Parity.......................................................................................10

4.2.3 BAUD Rate...............................................................................................................10

4.2.4 RTS On Time............................................................................................................10

4.2.5 RTS Off Time............................................................................................................11

4.2.6 Intercharacter Timeout..............................................................................................11

4.2.7 Remote Reply Timeout .............................................................................................11

4.2.8 Line Idle Time...........................................................................................................12

4.2.9 Retries Before Failure ...............................................................................................12

4.2.10 Failures Before Off-line........................................................................................12

4.2.11 Number of Devices on Port...................................................................................12

Chapter 5: Configuring the A164UNIT Table

5.1 General Information......................................................................................................13

5.2 Description of Fields.....................................................................................................13

5.2.1 Remote Address ........................................................................................................14

5.2.2 Unit Type...................................................................................................................14

5.2.3 Type 0 Read Interval.................................................................................................14

5.2.4 Type 1 Read Interval.................................................................................................15

5.2.5 Type 2 Read Interval.................................................................................................15

5.2.6 Type 3 Read Interval.................................................................................................15

5.2.7 Type 4 Read Interval.................................................................................................15

5.2.8 Type 5 Read Interval.................................................................................................15

5.2.9 Type 6 Read Interval.................................................................................................15

5.2.10 Type 7 Read Interval.............................................................................................16

5.2.11 Type 8 Read Interval.............................................................................................16

5.2.12 Time Synchronization Interval..............................................................................16

Chapter 6: Configuring the A164MODE Table

6.1 General Information......................................................................................................17

6.2 Description Of Fields ....................................................................................................18

6.2.1 First DVCF................................................................................................................18

6.2.2 Number of DVCF......................................................................................................19

Chapter 7: Configuring the A164DVCF Configuration Table

7.1 General Information......................................................................................................21

7.2 Description of Fields.....................................................................................................21

7.2.1 First Unit ...................................................................................................................22

7.2.2 Number of Units........................................................................................................22

BECCO2200 DCA

Configuration Guide

GE Energy Services

Restricted A164-0CG-1.00-2

Full

v

7.2.3 First Data Record ......................................................................................................22

7.2.4 Number of Data Records...........................................................................................22

Chapter 8: Configuring the A164DTBL Configuration Table

8.1 General Information......................................................................................................23

8.2 Description of Fields.....................................................................................................23

8.2.1 Table Type.................................................................................................................24

8.2.2 Point Number ............................................................................................................24

8.2.3 Data Value.................................................................................................................24

Appendix A: Messages Logged by the BECO2200 DCA

A.1 Fatal Error Messages.....................................................................................................25

A.2 Non-Fatal Error Messages.............................................................................................32

A.3 Warning Messages ........................................................................................................37

A.4 Information Messages ...................................................................................................38

A.5 Output Request Return Codes.......................................................................................40

Glossary of Terms

List of Acronyms and Abbreviations

GE Energy Services

BECCO2200 DCA

Configuration Guide

A164-0CG-1.00-2 Restricted

vi

Full

BECCO2200 DCA

Configuration Guide

GE Energy Services

Restricted A164-0CG-1.00-2

Full

vii

List of Figures

Figure 1 System Overview..........................................................................................................xvi

Figure 2 Relationship between A164MODE, A164UNOT. And A164FTBL Tables.................18

GE Energy Services

BECCO2200 DCA

Configuration Guide

A164-0CG-1.00-2 Restricted

viii

Full

BECCO2200 DCA

Configuration Guide

GE Energy Services

Restricted A164-0CG-1.00-2

Full

ix

List of Tables

Table 1 BECO2200 DCA Configuration Tables............................................................................2

Table 2 Required Points BECO2200 Device.................................................................................3

Table 3 BECO2200 DCA A164APPL Configuration Table ........................................................5

Table 4 BECO2200 DCA A164PORT Configuration Table.........................................................9

Table 5 Character Times at the Supported BAUD Rates.............................................................11

Table 6 BECO2200 DCA A164UNIT Configuration Table........................................................13

Table 7 BECO2200 DCA A164MODE Configuration Table .....................................................18

Table 8 BECO2200 DCA A164DVCF Configuration Table.......................................................21

Table 9 BECO2200 DCA A164DTBL Configuration Table.......................................................23

Table 10 WESDAC Number Definitions.....................................................................................27

GE Energy Services

BECCO2200 DCA

Configuration Guide

A164-0CG-1.00-2 Restricted

x

Full

Restricted A164-0CG-1.00-2

Full

xi

About this Guide

Purpose of this Guide

This guide describes, in detail, how to configure the BECO2200 Data Collection

Application (DCA) for GE Energy Services products. The configuration information

customizes the behavior of the BECO2200 DCA for communications with the Beckwith

Electric BECO2200-M-0420 Multifunction Relays.

Each configurable parameter for the BECO2200 DCA is described along with the range

of valid entries and a typical entry, where applicable. The grouping of related parameters

is also described.

Who Should Use this Guide

This document is intended for use by individuals responsible for the configuration of the

BECO2200 DCA in GE Energy Services RTUs. These people should be familiar with

the operation and maintenance of RTUs in general, but may not be familiar with the GE

Energy Services family of products.

Before reading this document, you should have a basic understanding of the WESDAC

hardware environment, the configuration system, and the BECO2200 DCA.

GE Energy Services

BECCO2200 DCA

Configuration Guide

A164-0CG-1.00-2 Restricted

xii

Full

Additional Documentation

If you require more detail that this document provides, several supporting texts are

available. These include:

• BECO2200 DCA Functional Specification (A164-0FS.WES)

• This document provides detailed information on the functionality of the BECO2200

DCA.

• Introduction to the WESDAC D20 RTU (GEN-0003)

• This document provides introductory information into the components and operation

of a D20 RTU.

• WESMAINT II Maintenance Facility User’s Guide (B014-0UG.D20)

• This document describes the general usage of the WESMAINT MMI provided with

every RTU.

• WESMAINT II Maintenance Facility Configuration Guide (B014-0CG.D20)

• This manual provides information on how to configure the WESMAINT MMI

application.

• D20 M Monitor User’s Reference (S001-0UG)

• This manual describes the use of the monitor function available in all RTUs.

• Config Pro Configuration System User’s Guide (P012-0UG)

• This manual provides information on using the Config Pro configuration system to

configure applications.

• WESDAC Configuration System User’s Guide (P005-0UG)

• This manual provides information on using Configuration System 1 to configure

applications.

• WIN User’s Configuration Guide (B008-0CG.D20)

• This manual provides detailed information on configuring the WESDAC Interface

Node (WIN).

BECCO2200 DCA

Configuration Guide

GE Energy Services

Restricted A164-0CG-1.00-2

Full

xiii

How this Guide is Organized

This guide is organized into the following sections:

Overview: The Overview discusses the general operation of the BECO2200 DCA.

Chapter 1: Configuration Tables provides general information on the configuration

tables required by the BECO2200 DCA.

Chapter 2: Configuring Win for the BECO2200 DCA details the WESDAC points

allocation required by the BECO2200 DCA.

Chapter 3: Configuring the A164APPL Table provides detailed information on

configuring the BECO2200 DCA application configuration table.

Chapter 4: Configuring the A164PORT Table provides detailed information on

configuring the BECO2200 DCA communication port configuration

table.

Chapter 5: Configuring the A164UNIT Table provides detailed information on

configuring the BECO2200 DCA unit configuration table.

Chapter 6: Configuring the A164MODE Table provides detailed information on

configuring the BECO2200 DCA Mode Download Pseudo Control

configuration table.

Chapter 7: Configuring the A164DVCF Configuration Table provides detailed

information on configuring the BECO2200 DCA Device/Configuration

Map configuration table.

Chapter 8: Configuring the A164DTBL Configuration Table provides detailed

information on configuring the BECO2200 DCA Data Records

configuration table.

Appendix A: Messages Logged by the BECO2200 DCA lists all fatal, error, warning,

and information messages logged by the BECO2200 DCA. This section

also provides a definition of all output request return codes.

GE Energy Services

BECCO2200 DCA

Configuration Guide

A164-0CG-1.00-2 Restricted

xiv

Full

Restricted A164-0CG-1.00-2

Full

xv

Overview

The BECO2200 DCA is a custom software package that provides an interface to

Beckwith Electric M-0420 Multifunction Relays.

The communication system consists of a master-slave sequence of messages, where the

BECO2200 DCA acts as the master and the BECO2200 devices act as slaves.

The BECO2200 DCA is an application module intended to be integrated in a modular

software environment. Figure 1 shows the data flow between the software modules in a

typical integration. As shown in this figure, the WESDAC Interface Node (WIN)

provides the only interface between the BECO2200 and the other modules in the system.

GE Energy Services

BECCO2200 DCA

Configuration Guide

A164-0CG-1.00-2 Restricted

xvi

Full

Figure 1 System Overview

WESDAC

Interface

Node

(WIN)

Data

Processing

Application

(DPA)

Wesmaint

Local I/O

DCA

BECO2200

Master

Station

Wesmaint

Display

(VT100)

Local

Hardware

BECO

Devices

HOST

Command

DPA

Response

WIN Response

WIN Event

DPA Data

WESDAC

Tables

WIN

Command

Data

Request

Requested

Data

DCA

Command

DCA Event

DCA

Response

DCA Event

DCA

Response

BECO2200

DCA Data

DCA

Command

Data Update

WESDAC

Tables

WIN Response

WIN Event

Operator

Request

Display

Data

Local I/O

DCA Data

WIN

Command

Response

Data

Request

Device

Restricted A164-0CG-1.00-2

Full

1

Chapter 1: Configuration Tables

The BECO2200 DCA configuration contains all of the data structures necessary to configure an

RTU to communicate with BECO2200 slave devices.

1.1 BECO2200 DCA Configuration Tables

There are a total of six (6) configuration tables in the BECO2200 DCA configuration.

Each table is named according to a standard convention that is used for all tables commonly

found in GE Energy Services applications. The standard naming convention dictates that the

prefix (first four characters) of the table name consist of an application descriptor. This

descriptor is an arbitrary identification code chosen by GE Energy Services to indicate the

application with which the table is associated. The application descriptor for the BECO2200

DCA is A164. The last four characters of the name describe the function of the table. For

example, A164PORT defines the characteristics of the communication ports. The purpose of

each table is described below.

TABLE NAME DESCRIPTION

A164APPL

This table always contains a single record, defining parameters that affect the entire

operation of the BECO2200 DCA.

A164PORT

This table configures the communication characteristics of each serial port used.

Each record in this table defines one port.

A164UNIT

This table defines each BECO2200 device with which the BECO2200 DCA will

communicate. Each record in this table defines a single unit.

A164MODE

This table defines the associated action of each Mode Download Pseudo Control.

A164DVCF

This table defines the set of data table records to download to a range of

BECO2200 Relays.

A164DTBL

This table defines each data table record being written to the Data Table of the

BECO2200 Relays.

GE Energy Services

BECCO2200 DCA

Configuration Guide

A164-0CG-1.00-2 Restricted

2

Full

Table 1 BECO2200 DCA Configuration Tables

1.2 Configuration Sequence

The following is a list of the steps required to configure the BECO2200 DCA:

1. Edit the A164 configuration. Prepare it according to the guidelines in this document and the

specific use for which the BECO2200 DCA is required.

2. Edit the configuration for all other applications that will run on the product. Prepare them

according to their own configuration guides.

3. Generate the configuration and download it to the product using the GE Energy Services

Configuration System provided. The list of applications to be compiled must include A164.

4. Restart the product. The BECO2200 DCA will check the validity of its configuration

parameters and begin its initialization. If it determines that a configuration parameter is

incorrect or encounters an error during its initialization, it will log a message to the

WESMAINT Error Log and then, depending on the severity of the error, terminate or

continue with its run-time function. Self-termination of the BECO2200 DCA prevents it from

running using invalid data.

5. Check for error messages. Log into the WESMAINT maintenance interface, select the

System Functions item from the Main Menu, and then select the Error Log item from the

System Functions Menu. If any error messages are displayed, correct the problem as

described in Appendix A: Messages Logged by the BECO2200 , and repeat steps 3 through 5.

Configuration is complete when the BECO2200 DCA has successfully validated all

configuration parameters.

Restricted A164-0CG-1.00-2

Full

3

Chapter 2: Configuring Win for the

BECO2200 DCA

This chapter describes how to configure the WESDAC Interface Node (WIN) for the BECO2200

DCA. The application number for WIN is B008. Refer to the WIN User’s Configuration Guide

for more information on how to configure WIN. The functionality of all points required by the

BECO2200 DCA is defined in the BECO2200 DCA Functional Specification.

2.1 WESDAC Point Allocation

WESDAC data point allocation is accomplished by specifying the required number of points in

the WIN configuration tables. Any points allocated to the BECO2200 DCA are maintained

solely by the BECO2200 DCA. This means the BECO2200 DCA is the only application that

may modify the value or the status of those points. All points allocated to the BECO2200 DCA

are initialized to off-line and not communicating. If the WESDAC table is in NVRAM, points

are initialized to the current value (state) in NVRAM. If the WESDAC table is in RAM, the

points are initialized to zero (off).

Number of points required

WESDAC DATA TYPE

BECO 2200 M-0420

Binary Inputs 42

Binary Outputs 44+MDPC

Counters 38

Analog Input 281

Analog Outputs 78

Device Status 1

Table 2 Required Points BECO2200 Device

GE Energy Services

BECCO2200 DCA

Configuration Guide

A164-0CG-1.00-2 Restricted

4

Full

☞

☞☞

☞NOTE: The actual number of Binary Output points required must be incremented

by the number of Mode Download Pseudo Controls configured.

2.1.1 Binary Inputs

When communication is established with a device and valid data is returned for the binary input

point, the point is turned on-line and communication OK. If communication between the device

and the point fails, all binary input points associated with the device will be set off-line and

communication failed.

2.1.2 Binary Outputs

On startup, all pseudo controls associated with a valid device and all Mode Download Pseudo

Controls are placed on-line and communication OK. When communication is established with a

device, the remaining binary outputs are set on-line and communication OK. If communication

between the device and the points fails, all binary output points, excluding pseudo controls, will

be set off-line and communication failed.

2.1.3 Counters

When communication is established with a device and valid data is returned for the counter, the

point is turned on-line and communication OK. If communication between the device and the

point fails, all counters associated with the device will be set off-line and communication failed.

2.1.4 Analog Inputs

When communication is established with a device and valid data is returned for the analog input

point, the point is turned on-line and communication OK. If communication between the device

and the point fails, all analog input points associated with the device will be set off-line and

communication failed.

2.1.5 Analog Outputs

On startup, all analog outputs associated with a valid device are placed on-line and

communication OK. If communication between the device and the point fails, all analog output

points associated with the device will be set off-line and communication failed.

2.1.6 Device Status

When communication is established with a device, the device status point is set on-line and

communication OK. If communication between the device and the point fails, the device status

point will be set off-line and communication failed.

Page is loading ...

GE Webcam BECCO2200 User manual

This manual is also suitable for

GE Webcam BECCO2200 User manual

Related papers

Other documents