Summit VT65ML7BIMED Owner's manual

Brand: Summit

Model: VT65ML7BIMED

Type: Owner's manual

 FF6L/ FF7L MED Series

All-refrigerators with automatic defrost

 FF28L/ FF29BL/ FF32L/ FF511L/ FF521BL/ FF560L/ FFAR2L/

FFAR21L/ FFAR22L MED Series

Compact all-refrigerators with automatic defrost

 FFAR9L/ FFAR10 MED Series

Mid-size/ Full-size storage all-refrigerators

 SCR450L/ SCR500BL/ SCR600/ SP6DS2D7/ SP6DS7/ SP6DSSTB7

MED Series

Specialty all-refrigerators (drawers or glass doors)

 CM411L/ CM421BL/ CP35LL/ CT66L/ S19L MED Series

Compact refrigerator-freezers

 CP171MED

Two-door refrigerator-freezer with two compressors

 CF05/ CF07ES/ FS60L/ UF850L // FCL44/ FS407L/ FS408BL/

SCF401SS MED Series

Mid-size // Compact freezers

 FS62L/ VT65ML // SCFF55L MED Series

Low-temperature freezers // Built-in frost-free freezers

 FS20L/ FS21L/ FS22L MED Series

All-freezers (-20°C)

 VT/ VLT Series

Low temperature freezers

 SCUF/ SCUR Series

Full-size frost-free all-freezers and all-refrigerators

 SCFF/ SCFR Series

Frost-free chest freezers and refrigerators

SUMMIT APPLIANCE

MEDICAL, LABORATORY AND SCIENTIFIC REFRIGERATORS AND FREEZERS

If you need service or call with a question, please have this

information ready. We advise you to keep this Use & Care

Guide in your possession.

Model: ____ Serial number: _

Options added:

Date of purchase: Dealer:

For parts: visit our website www.summitappliance.com/support

USE & CARE GUIDE

Felix Storch, Inc.

APPLIANCE SAFETY

Your safety and the safety of others are very important to us.

We have provided many important safety messages in this manual and

on your appliance. Always read and obey all safety messages.

You can be seriously injured or even killed if you don’t follow instructions.

Safety messages will tell you what the potential hazard is, how to reduce

the chance of injury, and what can happen if the instructions are not

followed.

 Plug into a grounded 3-prong outlet.

 Do not remove ground prong, nor use a 3/2 adapter.

 Do not use an extension cord.

 Use care not to plug into outlets controlled by wall switches.

 Disconnect power before servicing.

 After servicing, replace all parts and panels before operating.

 Use nonflammable cleaners.

 Keep flammable materials and vapors, such as gasoline, away from

appliances.

 Use two or more people to move and install appliance.

Drawer refrigerators are provided with anti-tip brackets. Always install

prior to use.

Proper Disposal of Your Old Appliance e

Old appliances can represent a suffocation hazard to children.

Remove doors from your old appliance.

Leave shelves in place.

If an old appliance contains refrigerants, it must be recycled by a licensed

service or disposal company.

IMPORTANT SAFETY INSTRUCTIONS

WARNING: To reduce the risk of fire, electric shock, or injury

when using your appliance, follow these basic precautions:

Felix Storch, Inc.

Page 2

INSTALLATION INSTRUCTIONS

Excessive Weight Hazard !

Use two or more people to move and install your appliance.

Failure to do so can result in back or other injury.

ALLOW APPLIANCE TO SIT UPRIGHT FOR 24 HOURS BEFORE TURNING

ON, TO ALLOW THE COMPRESSOR LUBRICANT TO DRAIN.

1. Remove packaging materials.

2. Remove tape and glue residue from surfaces before turning on the

appliance. Rub a small amount of liquid dish soap over the adhesive

with your fingers. Rinse with warm water and dry.

3. Do not use sharp instruments, rubbing alcohol, flammable fluids, or

abrasive cleaners to remove tape or glue. These products can

damage the surface of your appliance.

4. When Moving Your Appliance

Your appliance is heavy. When moving the appliance for cleaning or

service, be sure to protect the floor. Always pull the appliance straight

out when moving it. Do not wiggle or “walk” the appliance when trying

to move it, because floor damage can occur.

5. Clean Before Using:

After you remove all of the packaging materials, clean the inside of

your appliance before using it. See cleaning instructions in Appliance

Care.

6. Some upright models have leveling legs. Level as necessary for best

operation.

7. If your appliance has casters, after moving into place, lock the brakes

on those casters supplied with brakes. Always unlock before moving

the appliance for cleaning.

Key Eject Lock (some models)

To lock or unlock the appliance, you must hold the key in the lock while

turning. The lock is spring loaded, so the key cannot be left in the lock.

If the key is lost, contact your dealer or SUMMIT APPLIANCE for a

replacement. Always give the model and serial number of your appliance

when requesting a replacement key. Keys for most models can be

ordered online at www.summitappliance.com/support

Felix Storch, Inc.

Page 3

LOCATION REQUIREMENTS

Keep flammable materials and vapors, such as gasoline,

away from appliances. Failure to do so can result in fire,

explosion or death.

IMPORTANT: Do not install the appliance near an oven, radiator, or

other heat source, nor in a location where the temperature will fall below

40°F (5°C). Do not place in direct sunlight.

Check the strength of the floor before installing your appliance. It should

hold the weight of a fully loaded appliance. Allow at least 1” (2.5 cm) of

airspace at the top and on both sides of the appliance and 1” (2.5 cm)

between the back of the appliance and the wall. If the appliance is going

to be placed against a wall, leave extra space on the hinge side so the

door can open wider than its width.

Note: This appliance may be installed side by side with another

appliance or appliances. Allow for a 3” (7.5 cm) clearance at the top

and sides and a ¼” (0.64 cm) clearance between the appliances. IF

YOUR MODEL HAS THE LETTERS “BI” IN THE SUFFIX, IT IS

DESIGNED FOR BUILT-IN USE, AND DOES NOT REQUIRE

CLEARANCE EXCEPT IN THE BACK.

Electrical Shock Hazard

 Plug into a grounded 3-prong outlet.

 Do not remove ground prong.

 Do not use an adapter.

 Do not use an extension cord.

Failure to follow these instructions can result in fire, electrical

shock or death.

Recommended grounding method

A 115 Volt (AC only) 60 Hz grounded electrical supply with a 15- or 20-

amp fuse or circuit breaker is required. It is recommended that a separate

circuit serving only your appliance be provided. Use outlets that cannot

be turned off by a switch or pull chain. Do not use an extension cord.

Felix Storch, Inc.

Page 4

1. Locate the two front leveling legs that may be taped among the packing

materials. In many models these legs are already mounted into the

underside of the appliance.

2. Screw these legs into the front holes on the bottom of the appliance. The

back of the appliance rests on two fixed supports. (Built-in models also

have rear level legs that can provide more precise leveling).

3. Adjust the front legs just enough to lift the cabinet up off the floor.

Note: If your model is equipped with front rollers, the front legs should be

lowered enough to lift the rollers off of the floor to ensure the appliance

does not roll forward when the door is opened.

4. Place a leveling tool on top of the appliance, first side to side, then front to

back. Turn leg counterclockwise to raise a corner. Turn leg clockwise to

lower a corner.

5. Repeat Step 4 until appliance is level.

6. After appliance is fully loaded, recheck with level as in Step 4.

7. If your appliance is equipped with casters, the two front casters have

brakes to prevent rolling. Keep brakes locked, and unlock for moving only.

Level your appliance (some upright models)

APPLIANCE USE

In order to ensure proper temperature, you need to permit proper airflow in

the appliance. Do not block off any air vents. If the vents are blocked, airflow

will be prevented, and temperature and moisture problems may occur. Always

position contents to allow some airflow between shelves or baskets.

Allow the appliance to cool at least 6 to 8 hours before adding contents. Allow

24 hours for temperature to stabilize.

Note: When the appliance is first started, the compressor will run constantly

until the appliance is cooled. It may take 6 to 8 hours (or longer),

depending on room temperature and the number of times the appliance

door is opened. After the appliance is cooled, the compressor will turn on

and off as needed to keep the appliance at the proper temperature.

The outside of your appliance may feel warm. This is normal. The appliance’s

design and main function is to remove heat from packages and air space

inside the appliance. The heat is transferred to the room air, making the

outside of the appliance feel warm. (In some models the condenser that gets

warm is just inside the side walls, making these walls warm to the touch.).

ENERGY-SAVING TIPS

 The more airflow you can provide around an appliance, the less energy it will

use.

 If your appliance requires manual defrosting, keep ice build-up to less than 1/2

inch.

 Keep doors open a minimum of time, and shut securely.

Felix Storch, Inc.

Page 5

REVERSING THE DOOR SWING

(Selected models)

If you find the direction of opening the door on your appliance inconvenient, you

can change it. Holes on the opposite side have already been prepared in the

factory.

For two-door units:

 Take off the upper hinge cover from the top door and

remove the screws that hold the top hinge.

 Lift the hinge straight up to free the hinge pin from the

socket in the top of the door.

 Lift the top door to free its bottom socket from the hinge

pin on the central hinge bracket.

 Remove the screws to the central hinge to free its pin

from the top of the lower door.

 Lift the door up and away from the bottom hinge

pin.

 Remove the screws to the bottom hinge.

 Remove the decorative caps from the opposite

side and install the bottom hinge. Plug the holes

from the original side with the decorative caps.

 Replace door onto the pin on the bottom hinge,

then install the central hinge into lower door.

 Insert screws into the central hinge and plug the

holes on the reverse side.



Replace the upper door onto the central hinge pin.

 Insert screws into the top hinge and tighten.

For one-door units:

 Take off the upper hinge cover from the door and

remove the screws that hold the top hinge.

 Lift the hinge straight up to free the hinge pin from

the socket in the top of the door.

 Lift the door up and away to free its bottom

socket from the hinge pin.

 Remove the screws to the bottom hinge.

 Remove the decorative caps from the opposite side and plug the holes from the

original side with the decorative caps.

 Move the bottom hinge to the opposite side and

tighten the screws. Install any lock washers or nuts

if they were used in the original installation.

 Replace door onto the hinge pin on the bottom

hinge. Place top hinge pin into door. Insert screws

into the top hinge and tighten.

Felix Storch, Inc.

Page 6

APPLIANCE CARE

Cleaning Your Frost-Free Refrigerator

(including models beginning with SCFF, SCFR, SCUF, SCUR)

Use nonflammable cleaners.

Frost-free means that you do not have to defrost your appliance. Frost is

removed by air moving and collecting any moisture and depositing it on the

cooling coil. The cooling coil periodically warms up enough to melt the frost,

and the water then flows down to the drain pan (located behind the base grill)

where it is evaporated.

Complete cleaning should be done at least once a year.

1. Unplug appliance or disconnect power.

2. Remove all substances.

3. Wash the inside walls with a solution of mild detergent in warm water or

2 tbs (26 g) baking soda to 1 qt (0.95 L) warm water.

 Do not use abrasive or harsh cleaners such as window sprays,

scouring cleansers, flammable fluids, cleaning waxes, concentrated

detergents, bleaches or cleansers containing petroleum products on

plastic parts, interior and door liners or gaskets. Do not use paper

towels, scouring pads, or other harsh cleaning tools. These can

scratch or damage surfaces.

4. Rinse well and wipe dry with a clean soft cloth.

5. Use the appropriate cleaning method for the exterior finish.

Painted metal

: Wash exteriors with a clean sponge or soft cloth and a

mild detergent in warm water. Do not use abrasive or harsh cleaners,

or cleaners designed for stainless steel. Dry thoroughly with a soft

cloth. For additional protection against damage to painted metal

exteriors, apply appliance wax (or auto paste wax) with a clean, soft

cloth. Do not wax plastic parts.

6. Plug in appliance or reconnect power.

7. Replace all containers.

Cleaning your cycle defrost or manual defrost refrigerator

Cycle defrost models utilize a system where ice builds up on the rear wall and

melts when the compressor is off. Manual defrost models continually build ice

on inner walls.

NEVER USE A METAL OBJECT TO REMOVE ICE FROM THE REAR WALL.

IF NEEDED, USE A PLASTIC ICE-SCRAPER OR A HAIR DRYER.

Clean surfaces using the same instructions as for frost-free models.

For CSS Models (completely stainless steel), only use cleaners

especially made for stainless steel.

Felix Storch, Inc.

Page 7

Base Grill (some models only)

To Remove and Replace the Base Grill:

1. Open the appliance door and remove the base grill by pulling down

and out from the top.

2. Replace the base grill by putting the clips in the openings in the

appliance panel. Push in until the base grill snaps into place.

Changing the Light Bulb (some models only)

NOTE: Not all appliance bulbs will fit your appliance. Be sure to replace

the bulb with one of the same size, shape, base size and wattage. You

can purchase bulbs from www.summitappliance.com/support

1. Unplug appliance or disconnect power.

2. Remove the light shield. Most models do not require tools.

3. Replace the light bulb with an appliance bulb of the same wattage.

4. Replace the light shield.

5. Plug in appliance or reconnect power.

Loss of Power

After the power is restored, unplug the appliance for 30 minutes to allow

the refrigeration system to equalize. During this time, keep the door

closed as much as possible.

Remember: A full appliance stays cold longer than a partially filled one.

Moving Care

1. Remove all containers.

2. Unplug the appliance.

3. Clean it thoroughly.

4. Tape the appliance shut and tape the electrical cord to the cabinet.

When you get to your new location, refer to the Installation Instructions

and Temperature Selection sections for information on installation and

setting the controls.

APPLIANCE CARE (cont’d)

Felix Storch, Inc.

Page 8

YOUR APPLIANCE MAY HAVE A MECHANICAL (DIAL) OR

DIGITAL THERMOSTAT. DIAL INSTRUCTIONS ARE BELOW.

DIGITAL INSTRUCTIONS ARE ON PAGE 10.

HOW TO ADJUST THE THERMOSTAT

Your refrigerator may be controlled with a thermostat knob located

inside the unit, towards the right-hand corner. Turn the knob

clockwise from the STOP (0) position toward the higher numbers

for colder temperatures.

Temperature Controls

 Higher settings on the knob (higher numbers) mean lower

temperatures (colder) in all compartments of the appliance. The

temperature inside a refrigerator may even drop below 32°F. Use

higher thermostat settings only when required or recommended.

When the ambient temperature is normal, we recommend a medium

setting.

 Changes of the ambient temperature affect temperature in the interior

of the appliance, so keep this in mind when choosing the setting of the

thermostat knob.

 In STOP (0) position, the appliance does not operate (the cooling

system is switched off), yet the power supply is not interrupted (the

light is on when you open the refrigerator door).

 The temperature in the refrigerator and in the freezer compartment

also depend on how often you open the door.

In all small refrigerators and freezers without interior fans, tempera-

tures are coldest near the bottom, and occasionally near the rear.

Place contents accordingly. It is best not to operate these units mostly

empty. If temperatures are erratic, try putting some water bottles or

freezer packs inside to create a load for the compressor.

TEMPERATURE SELECTION

Felix Storch, Inc.

Page 9

If you find that it is necessary to change the temperature setting for your

digital-thermostat controlled appliance, please refer to the following

instructions. The front panel of the thermostat is illustrated here:

melting

snowflake

UP & DOWN arrows

SET key

snowflake

To see the SET POINT:

Push and immediately release the SET key. The display will show the SET

POINT value. Wait 5 seconds and the probe value will display again.

To change the SET POINT:

Push and hold the SET key for more then 3 seconds to change the set point

value. The value of the set point will be displayed, and the “snowflake” LED

will start blinking.

To change the SET value:

Push the UP or DOWN arrow to the desired setting. The new setting will be

memorized after 15 seconds, provided no other keys are pushed.

Note: The minimum and maximum range of your thermostat is preset

and locked by us, so it cannot easily be accidentally moved between

freezer and refrigerator temperatures. To reset this range lock, either

call us or find information on our website under Troubleshooting.

DIGITAL THERMOSTAT INSTRUCTIONS

Resetting the Unit

Use a pointed object to push the RESET button on the back of

the alarm unit. It is necessary to reset the unit whenever a

change is made to °C/°F temperature or FAST/NORMAL

sampling rate, or if the probe sensor is plugged in or removed.

Note: HI/LO temperature alarm settings and MIN/MAX

memories will be cleared after resetting the unit.

DISPLAYING °F or °C

To display the temperature readings in Fahrenheit (°F) or Celsius (°C),

slide the switch on the back of the unit to °F or °C.

Note: The unit must be reset after changing the temperature unit.

SELECTING THE SAMPLING RATE

To select normal sampling rate (60 seconds) or fast sampling rate (10

seconds), slide the switch on back of unit to NORMAL or FAST.

Note: The unit must be reset after changing the sampling rate. Using the

NORMAL sam

lin

rate will extend batter

life.

ALARM INSTRUCTIONS (Selected Models)

Felix Storch, Inc.

Page 10

OPERATION MODES

SUMMIT alarms have two operating modes:

NORMAL DISPLAY MODE and ALARM

DISPLAY MODE. To change from one mode

to another, press the MODE button once.

NORMAL DISPLAY MODE - is indicated by the

display of current temperature and the MIN

(minimum) and MAX (maximum) temperatures.

These temperatures relate to internal (probe)

temperature if the probe is plugged in, and to

ambient temp if the sensor probe is removed.

ALARM DISPLAY MODE - is indicated by the

display of current temperature and the HI and LO

alarm settings. These temperatures relate to internal (probe) temperature if

the probe is plugged in, and to ambient temperature if the sensor probe is

removed.

RESETTING MIN/MAX MEMORIES

There are two ways to reset the memories:

1. To reset both minimum and maximum memories - press the MEMORY

CLEAR button.

2. To reset individual minimum and maximum memories - press either the

MIN or MAX button (on back of unit) once to reset the respective memory.

The other memory will remain unaffected.

Note: You must be in NORMAL Display Mode to reset the memories.

SETTING THE HIGH/LOW ALARM

1. Press the MODE button until unit is in the ALARM DISPLAY MODE

indicated by the display of current temperature and HI/LO alarm settings.

2. To set the HIGH temperature alarm limit, press the HI button to advance

the display in 1° increments, until the desired high temperature is displayed.

Press and hold the HI button to advance the display rapidly in 5° increments.

3. To set the LOW temperature alarm limit, press the LO button to advance

the display in 1° increments, until the desired low temperature is displayed.

Press and hold the LO button to advance the display rapidly in 5° increments.

ALARM

The unit will sound the alarm in both NORMAL DISPLAY MODE and ALARM

DISPLAY MODE. Slide the ALARM ON/OFF switch to ON. When the current

temperature display rises above the HI set point, or falls below the LO set

point, the alarm will sound for 1 minute and issue a 3-second repeater beep

every minute thereafter for up to 12 hours. The alarm will continue to sound

even if the current temperature display returns to an “in range” condition.

To temporarily silence the alarm, press either the HI or LO button on the back

of the unit. The unit is still active and the alarm will sound again if the

temperature goes out of range. To permanently silence the alarm, slide the

ALARM ON/OFF switch to the OFF position.

ALARM INSTRUCTIONS (cont’d)

Felix Storch, Inc.

Page 11

Factory-set default password:

The factory-set default password is 0123. If the default

password is lost, press the

key (located inside the battery

box) for 30 seconds, then wait for the warning sound which

signifies the factory-set default password has been restored.

To set the password: While door is open, press the key

(located inside the battery box) until it jingles, enter the 0123

password, then # within 10 seconds to confirm. Enter the

password (1-16 digits), then press # again to confirm. A total

of 10 passwords can be set.

Note:

Each password starts with a number from 0 to 9 in order. The first password

starting

with 0 is the default password. For example, use 1xxx, then 2xxx etc.

for 10 users.

Changing password

: While the door is open, press the key (located inside

the battery box) until it jingles, enter the old password and press # within 10

seconds to confirm. Enter the new password, then press # to confirm.

Note: The first digit cannot be changed.

To open the door

: While the door is closed, press the key, enter the

password, then press

again to confirm.

To lock door manually

: Press #.

Function setting of automatic lock

: Setting of the auto-lock time: Press the

key (inside the battery box), enter a number (any number between 10-99),

then press # to confirm. The auto-lock time can be set between 10-99 seconds

after opening the door. If the time is set less than 10 seconds, the door will not lock

automatically, only manually.

Deleting the door-opening passwords

: Press the key, enter default

password followed by 0000, then press # and all the door-opening passwords will

be deleted except for the default password.

Note: To access the battery box you need to remove only the two small screws on

the top and bottom of that cover. Do not remove the 4 screws holding the

keypad and cover to the appliance door.

KEYPAD LOCK (Optional on most models)

OPERATION OF SPECIFIC MODELS

SCFF55LMED Series

These are built-in, frost-free units that do not require defrosting. At the top of the unit is a

cooling system that uses a fan to provide cold air. For best operation, do not block the

air flow with contents. The thermostat is located at the top right of the unit.

Felix Storch, Inc.

Page 12

FF6L, FF7L, FF28L, FF29BL, FF32L, FF511L, FF521L, FF560L, FFAR2L,

FFAR9L, FFAR10, FFAR21L, FFAR22L, SCR450L, SCR500BL, SCR600L,

SP6DS2D7, SP6DS7, SP6DSSTB7 MED Series

These models are all-refrigerator (no freezer compartment) with automatic defrost. All have cold

plates on the rear wall, and the coldest spots in the refrigerator will be in the rear and toward the

bottom. All except FF511LMED, FF521BLMED, FFAR21L and FFAR22L have interior fans to promote

even cooling. In the rear bottom above the step, there is a drain line to allow defrost water to exit the

refrigerator. Keep this drain line clear, or icing inside the refrigerator will occur. FF7 and SCR series

models have lights that are not door-activated, and are controlled by a rocker switch on the top right.

The light generates a small amount of heat, so keep the light off for best operation and energy

savings. FF6 models, FF560L models, FFAR9L models and FFAR10L models all have door-activated

lights. Smaller models and drawer models do not have interior lights.

NOTE

: Models with BI in the model number, and all drawer units, are designed for built-in operation

and do not need clearance on the sides or above the units. All other models

require 1 inch of airflow

on the sides and above the units. All models operate best when 1 inch is provided between the rear

wall and the back of the unit.

CF05, CF07ES, FCL44, FS20L, FS21L, FS22L, FS60L, FS62L, FS407L,

FS408BL, SCF401SS, UF850L, VT65ML MED Series

These are manual defrost all-freezers. No internal fans are present, and ice will build up along the

cooling coils. Periodically defrost the ice (recommended when the ice level reaches a thickness of 1/4

to 1/2 inch). NEVER USE A METAL INSTRUMENT as you can damage the cooling coils, which will

void your warranty and often cannot be repaired. To defrost, disconnect from the power supply, empty

the contents, provide a tray in the bottom to collect water, and use a hairdryer or other source of warm

air to melt the ice (or leave the door open and the power off for 24 to 48 hours). (Chest freezer

CF07ESMED has a built-in drain outlet.)

For built-in (BI) models and clearance information, see Note above.

SCFF Series / SCFR Series (except SCFF55 series – See page 12)

These models are chest freezers or chest refrigerators, all completely frost-free with forced air

cooling. No defrosting is normally needed. For best operation, allow free airflow within the interior (do

not overfill). The thermostat is located on the bottom rear on the right side of the unit. Large sizes may

have lid-activated lights. The lights will generate some heat, so be careful to close lids securely to

deactivate.

SCUF18, SCUF20, SCUF25, SCUR18, SCUR20, SCUR25

The thermostat for these models is located on the exterior top of the units, and is always digital (see

Page 10 for instructions). All units are fully frost-free and normally never require defrosting. If supplied

with casters (standard), operate with at least two in the locked position, and never move units with

contents inside. If supplied with 6-inch legs (optional), the hex nut on the bottom of the legs can be

rotated to level the unit.

VT, VLT Low-Temperature freezer models

These models are all manual defrost, upright or chest type freezers. Keep door closed for best

operation, and follow defrosting instructions at the top of this page. The thermostats for these models

are always digital, so follow directions on Page 10. VERY LOW TEMPERATURE FREEZERS CAN

DAMAGE UNPROTECTED SKIN, SO ALWAYS WEAR GLOVES WHEN OPENING FREEZERS,

AND NEVER DISCARD THE WARNING LABELS ON THE FRONT OF THE FREEZER! These

freezers will operate best when adequate airflow is provided on the top, sides and rear of the unit. The

compressor on some models is fan-cooled, so be sure not to block the air vents on the compressor

housing. The refrigerant in low temperature freezers is different from that used in household

appliances, so never have unqualified technicians attempt to repair these units. These units will

operate best under some load, so try to avoid operating empty or nearly empty. If needed, fill with ice-

packs to at least 25% of the volume of the freezer.

SPECIFIC MODELS (cont’d)

Felix Storch, Inc.

Page 13

TROUBLESHOOTING

CP35LL, CT66L MED Series

These models are cycle defrost refrigerator-freezers. The freezers are designed to operate at 0°F

(-18°C), suitable for medical or laboratory uses. Both models have dual evaporators to maintain

separate temperatures in the freezer and refrigerator. Defrost the freezer carefully, as directed on the

previous page for manual defrost. The refrigerator section operates in the normal range (35 to 45°F,

or 2 to 7°C) and defrosts automatically.

For built-in (BI) models and clearance information, see Note on page 13.

CM411LMED, CM421BLMED, S19LMED

These models are manual defrost refrigerator-freezers. The freezers in these models are designed to

operate at 25°F (-4°C) to keep ice frozen, and not for medication or products needing colder

temperatures. Defrost carefully, following directions on the previous page. The refrigerator section will

operate in the normal range (35 to 45°F, or 2 to 7°C) and is suitable for most refrigerated products.

For built-in (BI) models and clearance information, see Note on page 13.

CP171MED

This model has a separate refrigerator (top) section with automatic defrost, and a freezer (lower)

section with manual defrost, each with its own compressor and thermostat for totally independent

control. The thermostats are both located on the top, on the exterior of the unit, and are more easily

accessed with the refrigerator door opened. This unit has no internal fans. Defrost as needed (see

page 13). For clearance information, see Note on page 13.

Try these solutions first to avoid the cost of an unnecessary service call.

Your appliance will not operate:



Has a household fuse blown or circuit breaker tripped?

Replace the fuse or reset the circuit breaker.

 Is the freezer defrosting (on some models)?

Recheck to see whether the freezer is operating in 30 minutes. Your freezer will regularly

run an automatic defrost cycle.

There is water in the defrost drain pan (on some models):



Is the freezer defrosting?

The water will evaporate. It is normal for water to drip into the defrost pan.

 Is it more humid than normal?

When it is humid, expect that the water in the defrost pan will take longer to evaporate.

The motor seems to run too much:



Is there excessive frost or a package preventing the door from closing?

Defrost and clean the freezer, or move the package so the door closes properly.

 Is the room temperature hotter than normal?

The motor will run longer under warm conditions. At normal room temperatures, the motor

will run about 40% to 80% of the time. Under warmer conditions, it will run even more.

 Has a large amount of food just been added to the freezer?

Adding a large amount of food warms the freezer. The motor normally will run longer to cool

the freezer back down.

 Is the door closed completely?

Push the door firmly shut. If it will not shut all the way, see The door will not close completely

later in this section.

SPECIFIC MODELS (cont’d)

Felix Storch, Inc.

Page 14

 Are the condenser coils dirty (on some models)?

This prevents heat transfer and makes the motor work harder. Clean the condenser

coils.

 Is the door gasket sealed all the way around?

If not, contact a qualified technician.

Note: If the problem is not due to any of the above, remember that the compressor on your

new appliance will operate longer than your old one due to its high-efficiency motor.

Temperature is too warm:



Are the air vents blocked?

This prevents cold air movement. Move objects away from the air vents.

 Is the door opened often?

Be aware that the freezer will warm when this occurs. In order to keep the freezer

cool, try to get everything you need out of the freezer at once, keep food organized so

it is easy to find, and close the door as soon as the food is removed.

 Has a large amount of food just been added to the freezer?

Adding a large amount of food warms the freezer. It can take several hours for the

freezer to return to the normal temperature.

The door will not close completely or is difficult to open:



Are food packages blocking the door?

Rearrange containers so that they fit more tightly and take up less space.

 Are the shelves or drawers out of position (on some models)?

Put the shelves and drawers back into their correct positions.

TROUBLESHOOTING (cont’d)

ASSISTANCE OR SERVICE

Before calling for assistance or service, please check Troubleshooting. It

may save you the cost of a service call. If you still need help, follow the

instructions below.

When calling, please know the purchase date and the complete model

and serial numbers of your appliance. This information will help us to

respond better to your request.

If You Need Replacement Parts

If you need to order replacement parts, we recommend that you only use

factory-specified parts. Factory-specified parts will fit right and work right

because they are made with the same precision used to build every new

SUMMIT® appliance.

Call customer service toll free in the USA:

1-800-287-8799 Monday to Friday 9:00 a.m. – 5:00 p.m. (ET)

Order parts online at www.summitappliance.com/support

Felix Storch, Inc.

Page 15

ONE YEAR LIMITED WARRANTY FOR APPLIANCE

Within the 48 contiguous United States, for one year from the date of purchase, when this

appliance is operated and maintained according to instructions attached to or furnished with

the product, warrantor will pay for factory-specified parts and repair labor to correct defects in

materials or workmanship. Service must be provided by a designated service company.

Outside the 48 states, all parts are warranted for one year from manufacturing defects. Plastic

parts, shelves and cabinets are warranted to be manufactured to commercially acceptable

standards, and are not covered from damage during handling or breakage.

5-YEAR COMPRESSOR WARRANTY

1. The compressor is covered for 5 years.

2. Replacement does not include labor.

ITEMS WARRANTOR WILL NOT PAY FOR:

1. Service calls to correct the installation of your appliance, to instruct you how to use your

appliance, to replace or repair fuses or to correct wiring or plumbing.

2. Service calls to repair or replace appliance light bulbs or broken glass shelves.

Consumable parts (such as filters) are excluded from warranty coverage.

3. Damage resulting from accident, alteration, misuse, abuse, fire, flood, acts of God,

improper installation, installation not in accordance with electrical or plumbing codes, or

use of products not approved by warrantor.

4. Replacement parts or repair labor costs for units operated outside the United States.

5. Repairs to parts or systems resulting from unauthorized modifications made to the

appliance.

6. Expenses for travel and transportation for product service in remote locations.

7. The removal and reinstallation of your appliance if it is installed in an inaccessible location

or is not installed in accordance with published installation instructions.

DISCLAIMER OF IMPLIED WARRANTIES – LIMITATION OF REMEDIES

CUSTOMER’S SOLE AND EXCLUSIVE REMEDY UNDER THIS LIMITED WARRANTY

SHALL BE PRODUCT REPAIR AS PROVIDED HEREIN. IMPLIED WARRANTIES,

INCLUDING WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR

PURPOSE, ARE LIMITED TO ONE YEAR. WARRANTOR SHALL NOT BE LIABLE FOR

INCIDENTAL OR CONSEQUENTIAL DAMAGES. SOME STATES DO NOT ALLOW THE

EXCLUSION OR LIMITATION OF INCIDENTAL OR CONSEQUENTIAL DAMAGES, OR

LIMITATIONS ON THE DURATION OF IMPLIED WARRANTIES OF MERCHANTABILITY OR

FITNESS, SO THESE EXCLUSIONS OR LIMITATIONS MAY NOT APPLY TO YOU. THIS

WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS AND YOU MAY ALSO HAVE OTHER

RIGHTS, WHICH VARY FROM STATE TO STATE.

WARRANTY

FELIX STORCH, INC.

770 Garrison Avenue

Bronx, New York 10474

Phone: (718) 893-3900

Fax: (718) 842-3093

www.summitappliance.com

For parts and accessory ordering,

troubleshooting and helpful hints,

visit:www.summitappliance.com/support

Revised December 2011

Summit VT65ML7BIMED Owner's manual

Summit VT65ML7BIMED Owner's manual

Summit VT65ML7BIMED Owner's manual

Related papers

Other documents