EN
User manual
Washing Machine
ZWF 1621
Contents
Safety information _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ 2
Safety instructions _ _ _ _ _ _ _ _ _ _ _ _ _ _ 3
Product description _ _ _ _ _ _ _ _ _ _ _ _ _ _ 4
Special accessories for installation _ _ _ _ _ _ 5
Control panel _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ 6
Programme chart _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ 8
Consumption values _ _ _ _ _ _ _ _ _ _ _ _ _ 11
Helpful hints and tips _ _ _ _ _ _ _ _ _ _ _ _ 12
First use _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ 13
Personalisation _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ 13
Daily use _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ 14
Care and cleaning _ _ _ _ _ _ _ _ _ _ _ _ _ _ 16
What to do if… _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ 19
Technical data _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ 22
Installation _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ 22
Environment concerns _ _ _ _ _ _ _ _ _ _ _ _ 24
Subject to change without notice.
Safety information
Before the installation and use of the appliance, carefully read the
supplied instructions. The manufacturer is not responsible if an incor-
rect installation and use causes injuries and damages. Always keep
the instructions with the appliance for future reference.
Children and vulnerable people safety
Warning! Risk of suffocation, injury or permanent disability.
• Do not let persons, children included, with reduced physical sen-
sory, reduced mental functions or lack of experience and knowl-
edge use the appliance. They must have supervision or instruction
for the operation of the appliance by a person who is responsible
for their safety.
• Do not let children play with the appliance.
• Keep all packaging away from children.
• Keep all detergents away from children.
• Keep children and pets away from the appliance door when it is
open.
• If the appliance has a child safety device, we recommend you acti-
vate it.
General Safety
• Before maintenance, deactivate the appliance and disconnect the
mains plug from the mains socket.
• Do not change the specification of this appliance.
2
www.zanussi.com
• Obey the maximum load volume of 6 kg (refer to the “Programme
chart” chapter).
• If the supply cord is damaged, it must be replaced by the manu-
facturer, its service agent or similarly qualified persons in order to
avoid a hazard.
•The operating water pressure (minimum and maximum) must be
between 0,5 bar (0,05 MPa) and 8 bar (0,8 MPa)
• The ventilation openings in the base (if applicable) must not be ob-
structed by a carpet.
• The appliance is to be connected to the water mains using the
new supplied hose-sets. Old hose sets must not be reused.
Safety instructions
Installation
• Remove all the packaging and the transit
bolts.
• Keep the transit bolts. When you move the
appliance again you must block the drum.
• Do not install or use a damaged appliance.
• Do not install or use the appliance where the
temperature is less than 0 °C or where it is
exposed to the weather.
• Obey the installation instruction supplied with
the appliance.
• Make sure that the floor where you install the
appliance is flat, stable, heat resistant and
clean.
• Do not install the appliance where the appli-
ance door can not be fully opened.
• Always be careful when you move the appli-
ance because it is heavy. Always wear safety
gloves.
• Make sure that there is air circulation be-
tween the appliance and the floor.
• Adjust the feet to have the necessary space
between the appliance and the carpet.
Electrical connection
Warning! Risk of fire and electrical shock.
• The appliance must be earthed.
• Make sure that the electrical information on
the rating plate agrees with the power supply.
If not, contact an electrician.
• Always use a correctly installed shockproof
socket.
• Do not use multi-plug adapters and extension
cables.
• Make sure not to cause damage to the mains
plug and to the mains cable. Contact the
Service or an electrician to change a dam-
aged mains cable.
• Connect the mains plug to the mains socket
only at the end of the installation. Make sure
that there is access to the mains plug after
the installation.
• Do not pull the mains cable to disconnect the
appliance. Always pull the mains plug.
• Do not touch the mains cable or the mains
plug with wet hands.
• This appliance complies with the E.E.C. Di-
rectives.
Water connection
• Make sure not to cause damage to the water
hoses.
• The appliance is to be connected to the wa-
ter mains using the new supplied hose-sets.
Old hose sets must not be reused.
3
www.zanussi.com
• Before you connect the appliance to new
pipes or pipes not used for a long time, let
the water flow until it is clean.
• The first time you use the appliance, make
sure that there is no leakage.
Use
Warning! Risk of injury, electrical shock,
fire, burns or damage to the appliance.
• Use this appliance in a household environ-
ment.
• Obey the safety instructions on the detergent
packaging.
• Do not put flammable products or items that
are wet with flammable products in, near or
on the appliance.
• Do not touch the glass of the door while a
programme operates. The glass can be hot.
• Make sure that you remove all metal objects
from the laundry.
• Do not put a container to collect possible wa-
ter leakage under the appliance. Contact the
Service to ensure which accessories can be
used.
Care and Cleaning
Warning! Risk of injury or damage to the
appliance.
• Do not use water spray and steam to clean
the appliance.
• Clean the appliance with a moist soft cloth.
Only use neutral detergents. Do not use
abrasive products, abrasive cleaning pads,
solvents or metal objects.
Disposal
Warning! Risk of injury or suffocation.
• Disconnect the appliance from the mains
supply.
• Cut off the mains cable and discard it.
• Remove the door catch to prevent children
and pets to get closed in the appliance.
Product description
1
Detergent dispenser drawer
2
Control panel
3
Door opening handle
4
Rating plate
5
Drain pump
6
Adjustable feet
1 2
3
4
5
6
4
www.zanussi.com
Detergent dispenser drawer
Compartment for detergent used for prewash
and soak phase or for stain remover used during
the stain action phase (if available). The prewash
and soak detergent is added at the beginning of
the wash programme. The stain remover is add-
ed during the stain action phase.
Compartment for powder or liquid detergent
used for main wash. If using liquid detergent
pour it just before starting the programme.
Compartment for liquid additives (fabric softener, starch).
Follow the product manufacturer’s recommendations on quantities to use and do not exceed the
«MAX» mark in the detergent dispenser drawer. Any fabric softener or starching additives must
be poured into the compartment before starting the wash programme.
Special accessories for installation
Rubber feet kit (4055126249)
Available from your authorized dealer.
The rubber feet are particularly recommended
on floating, slippery and wooden floors.
Mount the rubber feet to prevent vibration,
noises and displacement of the appliance dur-
ing operation.
Read carefully the instructions supplied with the
kit.
Fixing plate kit (4055171146)
Available from your authorized dealer.
If you install the appliance on a plinth, secure
the appliance in the fixing plates.
Follow the instructions supplied with the kit.
Child Safety device
Make sure that children or pets do not climb in-
to the drum. To prevent children and pets be-
coming trapped inside the drum this machine in-
corporates a special feature.
To activate this de-
vice, rotate the button
(without pressing it)
inside the door clock-
wise until the groove
is horizontal. If neces-
sary use a coin.
To disable this de-
vice and restore the
possibility of closing
the door, rotate the
button anti-clockwise
until the groove is ver-
tical.
5
www.zanussi.com
Control panel
On the following page there is a picture of the control panel. It shows the programme selector
dial as well as the buttons, pilot lights and the display. These are presented by relevant num-
bers on the following pages.
1 2 3 4 5 6 7 8
10
9
1
Programme selector dial
2
SPIN reduction button
3
OPTIONS button
4
PREWASH button
5
EASY IRON button
6
EXTRA RINSE button
7
START/PAUSE button
8
DELAY START button
9
DOOR LOCKED pilot light
10
Display
Programme selector dial, spin speed button and available options
Programme Selector Dial
It allows you to switch the appliance on/off and/
or to select a programme.
Spin Reduction
By pressing this button you can change the spin
speed of the selected programme.
Available options:
Rinse hold
By selecting this function the water of the last
rinse is not emptied out to prevent the fabrics
from creasing. Before opening the door it will be
necessary to empty out the water. To empty out
the water, please read the paragraph «At the
end of the programme».
Economy
Only for cottons and synthetic items lightly or
normally soiled at a temperature of 40°C or
higher. The washing time will be prolonged and
the washing temperature will be reduced. You
can use this option if you want to wash normally
soiled laundry and at the same time save ener-
gy.
Super Quick
Short cycle for lightly soiled items or for laundry
which needs only freshening up. We recom-
mend you to reduce the fabrics loading.
Prewash
By selecting this option the machine performs a
prewash cycle before the main wash phase. The
washing time will be prolonged. This option is
recommended for heavily soiled laundry.
Easy Iron
By selecting this option the laundry is gently
washed and spun to avoid any creasing. In this
6
www.zanussi.com
way ironing is easier. Furthermore the machine
will perform some additional rinses in some pro-
grammes. On cotton programmes the maximum
spin speed is reduced automatically.
Extra Rinse
This appliance is designed to save energy. If it
necessary to rinse the laundry using an extra
quantity of water (extra rinse), select this option.
Some additional rinses will be performed. This
option is recommended for people who are al-
lergic to detergents, and in areas where the wa-
ter is very soft.
Start Pause
This button allows you to start or to interrupt the
selected programme.
Delay Start
The programme can be delayed from 30 min -
60 min - 90 min, 2 hours and then by 1 hour up
to a maximum of 20 hours by means of this but-
ton.
Door locked pilot light
The pilot light 9 illuminates when the pro-
gramme starts and indicates if the door can be
opened:
• light on: the door cannot be opened. The ma-
chine is working or has stopped with water
left in the tub.
• light off: the door can be opened. The pro-
gramme is finished or the water has been
emptied out.
• light blinking: the door is opening in a few mi-
nutes.
Display (10)
10.1 10.2
The display shows the following information:
10.1: Child safety lock
This device permits you to leave the appliance
unattended during it's functioning.
10.2:
• Duration of the selected programme
After selecting a programme, the duration is
displayed in hours and minutes (for example
). The duration is calculated automati-
cally on the basis of the maximum recommen-
ded load for each type of fabric. After the
programme has started, the time remaining is
updated every minute.
• Delayed start
The Selected delay set by pressing the rele-
vant button appears on the display for a few
seconds, then the duration of the selected
programme is displayed again. The delay time
value decreases by one unit every hour and
then, when 1 hour remains, every minute.
• Alarm codes
In the event of operating problems, some
alarm codes can be displayed, for example
(see paragraph «What to do if...»).
• Incorrect option selection
If an option which is not compatible with the
set wash programme is selected, the mes-
sage Err is displayed at the bottom of the
display for a few seconds. The integrated red
light of button 7 starts flashing.
• End of programme
When the programme has finished the flash-
ing zero (
) is displayed. The pilot light 9
and the pilot light of button 7 go out. The
door can be opened.
7
www.zanussi.com
Programme chart
Programme
Maximum and Minimum Temperature
Cycle Description
Maximum Spin Speed
Maximum Fabrics Load
Type of Laundry
Options
Detergent
Compartment
COTTONS
90° - 30°
60°
— 40°
1)
Main wash - Rinses
Spin at the maximum speed
Max. load 6 kg - Reduced load 3 kg
White and coloured cotton (normally soiled items).
SPIN REDUCTION
RINSE HOLD
ECO
2)
SUPER QUICK
3)
PREWASH
4)
EASY IRON
5)
EXTRA RINSE
SYNTHETICS
60° - 30°
Main wash - Rinses
Maximum spin speed at 900 rpm
Max. load 3 kg - Reduced load 1.5 kg
Synthetic or mixed fabrics: underwear, coloured gar-
ments, non-shrink shirts, blouses.
SPIN REDUCTION
RINSE HOLD
ECO
2)
SUPER QUICK
3)
PREWASH
4)
EASY IRON
5)
EXTRA RINSE
DELICATES
40° - 30°
Main wash - Rinses
Maximum spin speed 700 rpm
Max. load kg 3 - Reduced load kg 1.5
Delicate fabrics: acrylics, viscose, polyester.
SPIN REDUCTION
, if available
RINSE HOLD
SUPER QUICK
3)
PREWASH
4)
EXTRA RINSE
HANDWASH
40° - Cold
Main wash - Rinses
Maximum spin speed at 900 rpm
Max. load 2 kg
Special programme for delicate fabrics with «hand wash-
ing» care symbol.
SPIN REDUCTION
RINSE HOLD
8
www.zanussi.com
Programme
Maximum and Minimum Temperature
Cycle Description
Maximum Spin Speed
Maximum Fabrics Load
Type of Laundry
Options
Detergent
Compartment
WOOL
40°
Main wash - Rinses
Maximum spin speed at 900 rpm
Max. load 2 kg
Washing programme for machine washable wool as well
as for hand washable woollens and delicate fabrics. Note:
A single or bulky item may cause imbalance. If the appli-
ance doesn’t perform the final spin phase, add more items,
redistribute the load manually and then select the spinning
programme.
SPIN REDUCTION
RINSE HOLD
JEANS
40°
Main wash - Rinses
Maximum spin speed at 1200 rpm
Max. load 3 kg
With this programme it is possible to wash items like trou-
sers, shirts or jackets in denim and also jersey realized
with hi-tech materials. (The Extra Rinse option will be acti-
vated automatically).
SPIN REDUCTION
RINSE HOLD
PREWASH
4)
EASY IRON
5)
CURTAINS
40°
Prewash - Main wash - Rinses
Maximum spin speed at 700 rpm
Max. load 2.5 kg
This programme it is possible to wash with an extra water
load. The machine will add automatically a prewash phase
before the main wash to eliminate the dust. (Do not put
any detergent in the prewash compartment).
SPIN REDUCTION
, if available
RINSE HOLD
EXTRA RINSE
9
www.zanussi.com
Programme
Maximum and Minimum Temperature
Cycle Description
Maximum Spin Speed
Maximum Fabrics Load
Type of Laundry
Options
Detergent
Compartment
SOAK
30°
Prewash - Soak for about 40 minutes - Stop with water in the tub
Max. load 6 kg
Special programme for heavily soiled laundry. The machine performs a soak at
30°C. At the end of this time the machine will stop automatically with water left in
the tub.
Before starting a new washing phase, it is necessary to empty out the water by:
• Draining only: turn the programme selector dial to Drain programme. (Press
the button 7).
• Draining and spinning: turn the programme selector dial to programme Spin,
reduce the spin speed by pressing the button 2, and then press button 7.
Important! This programme cannot be used for very delicate fabrics as silk or
wool. Pour the detergent for the soak programme into the appropriate compart-
ment. At the end of the soak (after having emptied out the water) you can select
the washing programme (first turn the programme selector dial to
, then to the
programme and press the button 5).
MINI PROGRAMME 30
Main wash - Rinses
Maximum spin speed at 700 rpm
Max. load 3 kg
Quick washing programme for cotton and synthetic items
which are lightly soiled or only need freshening up.
SPIN REDUCTION,
if available
RINSE
Rinses
Spin at the maximum speed
Max. load 6 kg
With this programme it is possible to rinse and spin cotton
garments which have been washed by hand. The machine
performs 3 rinses, followed by a final long spin. The spin
speed can be reduced.
SPIN REDUCTION
RINSE HOLD
EASY IRON
5)
EXTRA RINSE
DRAIN
Draining of water
Max. load 6 kg
For emptying out the water of the last rinse in programmes
with the Rinse Hold option selected.
SPIN
Drain and long spin
Spin at the maximum speed
Max. load 6 kg
Separate spin for hand washed cotton garments and after
programmes with the Rinse Hold option selected. You can
choose the spin speed by pressing the relevant button to
adapt it to the fabrics to be spun.
SPIN REDUCTION
10
www.zanussi.com
Programme
Maximum and Minimum Temperature
Cycle Description
Maximum Spin Speed
Maximum Fabrics Load
Type of Laundry
Options
Detergent
Compartment
= OFF
For cancelling the programme which is running or to switch the machine off .
1) Standard programmes for the Energy Label consumption values. According to regulation 1061/2010, these
programmes at 40°C and 60° C + the option Eco
set, are respectively the «standard 60° C cotton
programme» and the «standard 40° C cotton programme». They are the most efficient programmes in terms of
combined energy and water consumption for washing normally soiled cotton laundry.
The water temperature of the washing phase may differ from the temperature declared for the selected pro-
gramme.
2) This option is not active at a temperature lower than 40° C.
3) If you select the Super Quick option by pressing button 4, we recommend that you reduce the maximum load
as indicated. Full loading is possible however with somewhat reduced cleaning results.
4) If using liquid detergents, a programme without PREWASH must be selected.
5) With «Easy Iron» option Max. load 1.5 kg
Consumption values
The data of this table are approximate. Different causes can change the data: the quantity and
type of laundry, the water and ambient temperature.
Programmes Load
(kg)
Energy con-
sumption
(kWh)
Water con-
sumption (litre)
Approximate
programme du-
ration (mi-
nutes)
Remaining
moisture
(%)
1)
Cottons 60 °C 6 1.30 58 125 44
Cottons 40 °C 6 0.70 58 120 44
Synthetics 40 °C 3 0.50 45 95 37
Delicates 40 °C 3 0.55 60 65 37
Wool/Hand wash
30 °C
2 0.25 53 55 37
Standard cotton programmes
Standard 60 °C
cotton
6 0.90 54 175 44
Standard 60 °C
cotton
3 0.68 35 150 44
Standard 40 °C
cotton
3 0.60 37 141 44
1) At the end of spin phase.
11
www.zanussi.com
Off Mode (W) Left On Mode (W)
0.10 0.98
The information given in the charts above are in compliance with the EU Commission regulation 1015/2010
implementing directive 2009/125/EC.
Helpful hints and tips
Sorting out the laundry
Follow the wash code symbols on each garment
label and the manufacturer’s washing instruc-
tions. Sort the laundry as follows: whites, col-
oureds, synthetics, delicates, woollens.
Before loading the laundry
Never wash whites and coloureds together.
Whites may lose their «whiteness» in the wash.
New coloured items may run in the first wash;
they should therefore be washed separately the
first time.
Button up pillowcases, close zip fasteners,
hooks and poppers. Tie any belts or long tapes.
Remove persistent stains before washing.
Rub particularly soiled areas with a special de-
tergent or detergent paste.
Treat curtains with special care. Remove hooks
or tie them up in a bag or net.
Removing stains
Stubborn stains may not be removed by just
water and detergent. It is therefore advisable to
treat them prior to washing.
Blood: treat fresh stains with cold water. For
dried stains, soak overnight in water with a spe-
cial detergent then rub in the soap and water.
Oil based paint: moisten with benzine stain
remover, lay the garment on a soft cloth and dab
the stain; treat several times.
Dried grease stains: moisten with turpentine,
lay the garment on a soft surface and dab the
stain with the fingertips and a cotton cloth.
Rust: oxalic acid dissolved in hot water or a rust
removing product used cold. Be careful with
rust stains which are not recent since the cellu-
lose structure will already have been damaged
and the fabric tends to hole.
Mould stains: treat with bleach, rinse well
(whites and fast coloureds only).
Grass: soap lightly and treat with bleach
(whites and fast coloureds only).
Ball point pen and glue: moisten with ace-
tone
1)
, lay the garment on a soft cloth and dab
the stain.
Lipstick: moisten with acetone as above, then
treat stains with methylated spirits. Treat any re-
sidual marks with bleach.
Red wine: soak in water and detergent, rinse
and treat with acetic or citric acid, then rinse.
Treat any residual marks with bleach.
Ink: depending on the type of ink, moisten the
fabric first with acetone
1)
, then with acetic acid;
treat any residual marks on white fabrics with
bleach and then rinse thoroughly.
Tar stains: first treat with stain remover, methy-
lated spirits or benzine, then rub with detergent
paste.
Detergents and additives
Good washing results also depend on the
choice of detergent and use of the correct
quantities to avoid waste and protect the envi-
ronment.
Although biodegradable, detergents contain
substances which, in large quantities, can upset
the delicate balance of nature.
The choice of detergent will depend on the type
of fabric (delicates, woollens, cottons, etc.), the
colour, washing temperature and degree of soil-
ing.
All commonly available washing machine deter-
gents may be used in this appliance:
• powder detergents for all types of fabric
• powder detergents for delicate fabrics (60°C
max) and woollens
• liquid detergents, preferably for low tempera-
ture wash programmes (60°C max) for all
types of fabric, or special for woollens only.
1) do not use acetone on artificial silk
12
www.zanussi.com
The detergent and any additives must be placed
in the appropriate compartments of the dis-
penser drawer before starting the wash pro-
gramme.
If using liquid detergents, a programme without
prewash must be selected.
Your appliance incorporates a recirculation sys-
tem which allows an optimal use of the concen-
trated detergent.
Follow the product manufacturer’s recommen-
dations on quantities to use and do not ex-
ceed the «MAX» mark in the detergent dis-
penser drawer.
Quantity of detergent to be used
The type and quantity of detergent will depend
on the type of fabric, load size, degree of soiling
and hardness of the water used.
Follow the product manufacturers’ instructions
on quantities to use.
Use less detergent if:
• you are washing a small load
• the laundry is lightly soiled
• large amounts of foam form during washing.
Degrees of water hardness
Water hardness is classified in so-called “de-
grees” of hardness. Information on hardness of
the water in your area can be obtained from the
relevant water supply company, or from your lo-
cal authority. If the water hardness degree is
medium or high we suggest you to add a water
softener following always the manufacturer’s in-
structions. When the degree of hardness is soft,
readjust the quantity of the detergent.
First use
• Ensure that the electrical and water con-
nections comply with the installation in-
structions.
• Remove the polystyrene block and any
material from the drum.
• Pour 2 litres of water into the main wash
compartment
of the detergent drawer
in order to activate the ECO valve. Then
run a cotton cycle at the highest temper-
ature without any laundry in the machine,
to remove any manufacturing residue
from the drum and tub. Pour 1/2 a
measure of detergent into the main wash
compartment and start the machine.
Personalisation
Acoustic signals
The machine is provided with an acoustic de-
vice, which sounds in the following cases:
• at the end of the cycle
• if there is a fault.
By pressing the 4 and 5 buttons simultaneously
for about 6 seconds, the acoustic signal is de-
activated (except if there is a fault). By pressing
these 2 buttons again, the acoustic signal is re-
activated.
Child safety lock
This device permits you to leave the appliance
unattended so you do not need to worry that
children might be injured by or cause damage to
the appliance. This function remains enabled al-
so when the washing machine is not working.
There are two different ways to set this option:
1. Before pressing button 7: it will be impossi-
ble to start the machine.
2. After pressing button 7: it will be impossi-
ble to change any other programme or op-
tion.
To enable or disable this option press simulta-
neously for about 6 seconds buttons 2 and 3
until on the display, the icon
appears or dis-
appears.
13
www.zanussi.com
Daily use
Load the laundry
Open the door by
carefully pulling the
door handle out-
wards. Place the
laundry in the drum,
one item at a time,
shaking them out as
much as possible.
Close the door.
Make sure that no
laundry stays be-
tween the seal and
the door. There is a
risk of water leakage
or damage to the
laundry.
Measure out the detergent and the fabric
softener
Pull out the dispenser drawer until it stops.
Measure out the amount of detergent re-
quired, pour it into the main wash compart-
ment
or in the appropriate compartment if
the selected programme/option it requires
(see more details in "Detergent dispenser
drawer").
If required, pour fabric softener into the com-
partment marked
(the amount used must
not exceed the «MAX» mark in the drawer).
Close the drawer gently.
Select the required programme by means
of the programme selector dial (1)
Turn the programme selector dial to the re-
quired programme.
The green pilot light of button 7 starts to flash.
The selector dial can be turned either clockwise
or anticlockwise.
Turn the selector dial to position
to reset the
programme/to switch the machine OFF.
At the end of the programme the selector
dial must be turned to position
, to
switch the machine off.
Important! If you turn the programme selector
dial to another programme when the machine is
working, the red pilot light of button 7 will blink
3 times and the messageErr is displayed to
indicate a wrong selection. The machine will not
perform the new selected programme.
Select the spin speed by pressing button 2
When selecting a programme, the appliance
proposes automatically the maximum spin
speed provided for that programme. (See
"Washing programmes" for the maximum al-
lowed spin speed).
Press this button repeatedly to change the spin
speed, if you want your laundry to be spun at a
different speed. The relevant pilot light illumi-
nates.
Select the available options by means of
buttons 3, 4, 5 and 6
Depending on the programme, different options
can be combined. These must be selected after
choosing the desired programme and before
starting the programme. When these buttons
are pressed, the corresponding pilot lights illu-
minate. When they are pressed again, the pilot
lights go out. If an incorrect option is selected,
the integrated red pilot light of the button 7
flashes 3 times and the message Err is dis-
played.
For the compatibility among the washing pro-
grammes and the options see chapter «Wash-
ing programmes».
14
www.zanussi.com
Start the programme by pressing button 7
To start the selected programme, press this
button; the corresponding green pilot light
stops blinking.
The pilot light 9 illuminates to indicate that the
appliance starts operating and the door is
locked.
If you have chosen a delayed start, the machine
will begin the countdown.
Important! If an incorrect option is selected,
the message Err is displayed for a few seconds
and the red pilot light of this button blinks 3
times.
Select the Delay Start by pressing button
8
Before you start the programme, if you wish to
delay the start, press this button to select the
desired delay.
The selected delay time value will appear on the
display for a few seconds, then the duration of
the programme will appear again.
You must select this option after you have set
the programme and before you start the pro-
gramme.
You can cancel or modify the delay time at any
moment, before you press button 7.
Selecting the delay start :
1. Select the programme and the required op-
tions.
2. Select the delay start by pressing button 8.
3. Press button 7:
- the machine starts its hourly countdown.
- the programme will start after the selected
delay has expired.
Cancelling the Delay Start after having started
the programme:
1. Set the washing machine to PAUSE by
pressing button 7.
2. Press button 8 once. On the display will
appear
'.
3. Press button 7 again to start the pro-
gramme.
Important!
• The selected delay can be changed only after
selecting the washing programme again.
• The door will be locked throughout the delay
time. If you need to open the door, you must
first set the washing machine to PAUSE by
pressing button 7 and wait a few minutes be-
fore opening the door. After you have closed
the door, press the same button again.
Important! The Delay Start cannot be
selected with the draining programme.
Altering an option or a running
programme
It is possible to change some options before the
programme carries them out.
Before you make any change, you must pause
the washing machine by pressing button 7.
Changing a running programme is possible only
by resetting it. Turn the programme selector dial
to
and then to the new programme position.
Start the new programme by pressing button 7
again.
The washing water in the tub will be not emp-
tied out.
Interrupting a programme
Press the button 7 to interrupt a programme
which is running, the corresponding pilot light
starts blinking. Press the button again to restart
the programme.
Cancelling a programme
Turn the selector dial to
to cancel a pro-
gramme which is running. Now you can select a
new programme.
Opening the door after the programme
has started
First set the machine to pause by pressing the
button 7.
If the pilot light 9 blinks and after a few minutes
goes off, the door can be opened.
If the pilot light 9 remains lit, this means that the
machine is already heating or that the water lev-
el is too high. In any case, do not try to force the
door open!
If you cannot open the door but you need to
open it, you have to switch the machine off by
turning the selector dial to
. After a few mi-
nutes the door can be opened.
(Pay attention to the water level and tem-
perature!).
15
www.zanussi.com
After closing the door, it is necessary to select
the programme and options again and to press
button 7.
At the end of the programme
The machine stops automatically. Some acous-
tic signals sound and a blinking
appears on
the display. The pilot light of button 8 and the
pilot light 9 go off.
If you have set a programme or an option that
ends with water left in the tub, the pilot light 9
remains on. The door is locked to indicate that
the water must be emptied out. During this time
the drum continues to turn at regular intervals
until water draining.
Follow the below instructions to empty out the
water:
1.
Turn the programme selector dial to
.
2. Select the draining or spinning programme.
3. Reduce the spin speed if needed, by press-
ing the relevant button.
4. Press button 8.
At the end of the programme, the door is re-
leased and can be opened. Turn the programme
selector dial to
to switch the machine off.
Remove the laundry from the drum and carefully
check that the drum is empty. If you do not in-
tend to carry out another wash, close the water
tap. Leave the door open to prevent the forma-
tion of mildew and unpleasant smells.
Stand by : once the programme has finished
after a few minutes the energy saving system
will be enabled. The brightness of the display is
reduced. By pressing any button the appliance
will come out of the energy saving status.
Care and cleaning
Warning! You must DISCONNECT the
appliance from the electricity supply,
before you can carry out any cleaning or
maintenance work.
Descaling
The water we use normally contains lime. It is a
good idea to periodically use a water softening
powder in the machine. Do this separately from
any laundry washing, and according to the soft-
ening powder manufacturer's instructions. This
will help to prevent the formation of lime depos-
its.
External cleaning
Clean the exterior cabinet of the appliance with
soap and water only, and then dry thoroughly.
Cleaning the dispenser drawer
The washing powder and additive dispenser
drawer should be cleaned regularly.
Remove the drawer
by pressing the catch
downwards and by
pulling it out. Flush it
out under a tap, to re-
move any traces of
accumulated powder.
To aid cleaning, the
top part of the addi-
tive compartment
should be removed.
16
www.zanussi.com
Cleaning the drawer recess
Having removed the
drawer, use a small
brush to clean the re-
cess, ensuring that all
washing powder resi-
due is removed from
the upper and lower
part of the recess.
Replace the drawer and run the rinse pro-
gramme without any clothes in the drum.
Cleaning the pump
The pump should be inspected regularly and
particularly if:
• the appliance does not empty and/or spin;
• the appliance makes an unusual noise during
draining due to objects such as safety pins,
coins etc. blocking the pump;
• a problem with water draining is detected
(see chapter “What to do if...” for more de-
tails).
Warning!
1.
Disconnect the mains plug from the mains
socket.
2. Do not remove the filter while the appliance
operates. Do not clean the drain pump if
the water in the appliance is hot. The water
must be cold before you clean the drain
pump.
Proceed as follows:
Open the pump door.
Put a container below the recess of the drain
pump to collect the water that flows out.
Press the two levers and pull forward the
drainage duct to let the water flow out.
When the container is full of water, put the
drainage duct back again and empty the con-
tainer. Do steps 3 and 4 again and again until
no more water flows out from the drain pump.
1
2
Pull back the drainage duct.
Unscrew the filter and remove it.
Remove fluff and objects from the pump.
17
www.zanussi.com
Make sure that the impeller of the pump can
turn. If this does not occur, contact the service
centre.
2
1
Clean the filter under the water tap and put it
back in the pump into the special guides.
Make sure that you tighten correctly the filter
to prevent leakages.
Close the pump door.
Caution! When the appliance is in use
and depending on the programme selected
there can be hot water in the pump.
Never remove the pump cover during a wash
cycle, always wait until the appliance has
finished the cycle, and is empty. When refitting
the pump cover, ensure it is securely re-
tightened so as to stop leaks and young
children being able to remove it.
Cleaning the water inlet filters
Important! If the appliance doesn't fill, takes
long to fill with water, the starting button blinks
yellow or the display (if available) shows the
relevant alarm (see chapter "What to do if..." for
more details), check if the water inlet filters are
blocked .
To clean the water inlet filters:
• Turn off the water
tap.
• Unscrew the hose
from the tap.
• Clean the filter in
the hose with a stiff
brush.
• Screw the hose back onto the tap. Make
sure the connection is tight.
• Unscrew the hose from the machine. Keep
a rag nearby because some water may flow.
• Clean the filter in the valve with a stiff brush
or with the piece of cloth.
35°
45°
• Screw the hose back to the machine and
make sure the connection is tight.
• Turn on the water tap.
Frost precautions
If the machine is installed in a place where the
temperature could drop below 0°C, remove the
remaining water from the inlet hose and the
drain pump.
18
www.zanussi.com
1. disconnect the mains plug from the mains
socket.
2. close the water tap
3. unscrew the water inlet hose from the tap;
4. put the two ends of the inlet hose in a con-
tainer and let the water flow out of the
hose.
5. empty the drain pump as described in the
‘Emergency emptying out’ section.
6. when the drain pump is empty, install the
water inlet hose again.
Warning!
Make sure that the temperature is more than 0
°C before you use the appliance again.
The manufacturer is not responsible for dam-
ages caused by low temperatures.
Emergency emptying out
If the appliance cannot drain the water, proceed
as follows to empty out the machine:
1. pull out the plug from the power socket;
2. close the water tap;
3. if necessary, wait until the water has cooled
down;
4. open the pump door;
5. place a container on the floor below the re-
cess of the drain pump;
6. press the two levers and pull forward the
drainage duct to let the water flow out;
7. when the container is full of water, put the
drainage duct back again and empty the
container;
repeat this operation until water stops flow-
ing out;
8. if necessary clean the pump (refer to the
section ‘Cleaning the pump’ );
9. close the drain pump door.
When you drain the water with the emergency
drain procedure, you must activate again the
drain system:
1. Put 2 litres of water in the main wash com-
partment of the detergent dispenser.
2. Start the programme to drain the water.
What to do if…
Certain problems are due to lack of simple
maintenance or oversights, which can be solved
easily without calling out an engineer. Before
contacting your local Service Centre, please
carry out the checks listed below.
During machine operation it is possible that the
red pilot light of button 7 blinks, one of the fol-
lowing alarm codes appears on the display and
some acoustic signals sound every 20 seconds
to indicate that the machine is not working:
•
: problem with the water supply.
•
: problem with the water draining.
•
: door open.
Once the problem has been eliminated, press
the button 7 to restart the programme. If after all
checks, the problem persists, contact your local
Service Centre.
19
www.zanussi.com
Problem Possible cause/Solution
The machine does not start:
The door has not been closed.
• Close the door firmly.
The plug is not properly inserted in the power socket.
• Insert the plug into the power socket.
There is no power at the socket.
• Please check your domestic electrical installation.
The main fuse has blown.
• Replace the fuse.
The selector dial is not correctly positioned and/or the button 7 has not
been pressed.
• Please turn the selector dial and press the button 7 again.
The delay start has been selected.
• If the laundry are to be washed immediately, cancel the delay start.
The Child Safety Lock has been activated.
• Deactivate the Child Safety Lock.
The machine does not fill:
The water tap is closed.
• Open the water tap.
The inlet hose is squashed or kinked.
• Check the inlet hose connection.
The filter in the inlet hose or the inlet valve filter are blocked.
• Clean the water inlet filters. (See "Cleaning the water inlet filters" for
more details).
The door is not properly closed.
• Close the door firmly.
The machine does not empty
and/or does not spin:
The drain hose is squashed or kinked.
• Check the drain hose connection.
The drain filter is clogged.
• Clean the drain filter.
An option or a programme that ends with the water still in the tub or a
that eliminates all the spinning phases has been selected.
• Select the draining or spinning programme.
The laundry is not evenly distributed in the drum.
• Redistribute the laundry.
There is water on the floor:
Too much detergent or unsuitable detergent (creates too much foam) has
been used.
• Reduce the detergent quantity or use another one.
Check whether there are any leaks from one of the inlet hose fittings. It is
not always easy to see this as the water runs down the hose; check to
see if it is damp.
• Check the water inlet hose connection.
The drain or inlet hose is damaged.
• Replace it with a new one.
The filter has not been properly screwed in after cleaning action.
• Screw the filter fully in.
20
www.zanussi.com
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
-
19
-
20
-
21
-
22
-
23
-
24
-
25
-
26
-
27
-
28
