Summit CM411LSSHH Owner's manual

Brand: Summit

Model: CM411LSSHH

Category: Fridges

Type: Owner's manual

This manual is also suitable for

Write the Serial Number here:

_________________________

REFRIGERATOR with CHILLER COMPARTMENT

Models CM405

CM411L

CM421BL

Owner's Manual

BEFORE USE, PLEASE READ AND FOLLOW

ALL SAFETY RULES AND OPERATING INSTRUCTIONS

FELIX STORCH, INC.

770 Garrison Avenue

Bronx, NY 10474

www.summitappliance.com

CM405 CM405BI

CM411L CM411LBI

CM421BL CM421BLBI

IMPORTANT SAFEGUARDS

Your safety and the safety of others are very important.

We have provided many important safety messages in this manual and on your

appliance. Always read and obey all safety messages.

This is the Safety Alert Symbol. This symbol alerts you to potential

hazards that can kill or injure you and others. All safety messages

will follow the Safety Alert Symbol and either the words ”DANGER”

or “WARNING”.

DANGER means that failure to heed

this safety statement may result in

severe personal injury or death.

WARNING means that failure to

heed this safety statement may

result in extensive product damage,

serious personal injury, or death.

Safety messages will alert you to what the potential hazard is, tell you how to reduce the

chance of injury, and let you know what can happen if the instructions are not followed.

Before the refrigerator is used, it must be properly positioned and

installed as described in this manual, so read the manual carefully.

To reduce the risk of fire, electrical shock or injury when using the

refrigerator, follow basic precautions, including the following:



Plug into a grounded 3-prong outlet. Do not remove grounding prong, do not use an

adapter, and do not use an extension cord.

 It is recommended that a separate circuit, serving only your refrigerator, be provided.

Use receptacles that cannot be turned off by a switch or pull chain.

 Never clean refrigerator parts with flammable fluids. These fumes can create a fire

hazard or explosion. And do not store or use gasoline or other flammable vapors and

liquids in the vicinity of this or any other appliance. The fumes can create a fire

hazard or explosion.

 Before proceeding with cleaning and maintenance operations, make sure the power

line of the unit is disconnected.

 Do not connect or disconnect the electric plug when your hands are wet.

 Unplug the refrigerator or disconnect the power before cleaning or servicing. Failure

to do so can result in electrical shock or death.

 Do not attempt to repair or replace any part of your refrigerator unless it is specifically

recommended in this material. All other servicing should be referred to a qualified

technician.



Use two or more people to move and install the refrigerator. Failure to do so can

result in back or other injury.

 To ensure proper ventilation for your refrigerator, the front of the unit must be

completely unobstructed. Choose a well-ventilated area with temperatures above

F (16

C) and below 90

F (32

C). This unit must be installed in an area protected

from the elements, such as wind, rain, water spray or drips.

 The refrigerator should not be located next to ovens, grills or other sources of high

heat.

 The refrigerator must be installed with all electrical connections in accordance with

state and local codes. A standard electrical supply (115V AC only, 60 Hz), properly

grounded in accordance with the National Electrical Code and local codes and

ordinances, is required.

 Do not kink or pinch the power supply cord of the refrigerator.

 The fuse (or circuit breaker) size should be 15 amperes.

 It is important for the refrigerator to be leveled in order to work properly. You may

need to make several adjustments to level it.

 Never allow children to operate, play with or crawl inside the refrigerator.

 Do not use solvent-based cleaning agents or abrasives on the interior. These

cleaners may damage or discolor the interior.

 Do not use this apparatus for other than its intended purpose.

Risk of child entrapment

Child entrapment and suffocation are not problems of the past. Junked or abandoned

refrigerators are still dangerous, even if they will “just sit in the garage a few days.”

 Before you throw away your old refrigerator: Take off the doors. Leave the

shelves in place so that children may not easily climb inside.

 Never allow children to operate, play with, or crawl inside the refrigerator.

- SAVE THESE INSTRUCTIONS -

Table of Contents

Important Safeguards ......................................................................................................... 1 - 2

Location of Parts ..................................................................................................................... 3

Technical Information .............................................................................................................. 4

Installation Instructions ....................................................................................................... 4 - 6

Before Using Your Refrigerator ................................................................................... 4

Installing the Refrigerator ....................................................................................... 4 - 5

Electrical Connection / Extension Cord ....................................................................... 5

Reversing the Door Swing / Door Handle Installation .................................................. 6

Operating Your Refrigerator .................................................................................................... 7

Temperature Control / Ice Cube Tray / The Chiller Compartment .............................. 7

Care and Maintenance ....................................................................................................... 8 - 9

Defrosting Your Refrigerator / Cleaning Your Refrigerator / Power Failure ................ 8

Vacation Time / Moving your Unit / Energy-Saving Tips ............................................. 9

Problems with Your Refrigerator? (Troubleshooting) ............................................................ 10

Limited Warranty ................................................................................................................... 11

Location of Parts

Temperature

control knob

Door

Chille

compartmen

(ice cube tray)

Drip tra

Crisper cove

Crispe

Leveling legs

Wire shelves

(white units)

Glass shelves

(black units)

Technical Information

Models: CM405 & CM405BI (white without lock)

CM411L & CM411LBI (white with lock)

CM421BL & CM421BLBI (black with lock)

Capacity: 4.1 cubic feet

Electrical Input: 115V AC / 60Hz

Rated Current: 1.4A

Power Input: 100W

Refrigerant: R134a, 1.75 oz

Installation: Free-standing (CM405, CM411L, CM421BL)

Built-in (CM405BI, CM411LBI, CM421BLBI)

Unit Weight: 57 lbs

Unit Dimensions: 19⅞"W x 23¼"D x 33¼"H*

* For built-in models (-BI suffix), height can be adjusted from 33¼" to 34½"

* For models with suffix ADA, height is modified to 32” for use under lower counters

Installation Instructions

Before Using Your Refrigerator:

 Remove the exterior and interior packing.

 Check to be sure you have all of the following parts:

 1 drip tray

 1 ice cube tray

 2 wire shelves (models CM405, CM405BI, CM411L & CM411LBI)

 2 glass shelves (models CM421BL & CM421BLBI)

 1 crisper drawer with glass cover

 1 handle with screws and handle seal

 2 keys (except models CM405 and CM405BI)

 Before connecting the unit to the power source, let it stand for approximately 2

hours. This will reduce the possibility of a malfunction in the cooling system from

handling during transportation.

 Clean the interior surface with lukewarm water using a soft cloth.

Installing the Refrigerator

 Place your unit on a floor that is strong enough to support the unit when it is fully

loaded. To level your unit, adjust the leveling legs at the bottom.

 Models CM405, CM411L and CM421BL are designed to be free-standing only,

and should not be recessed or built in. On the other hand, models CM405BI,

CM411LBI and CM421BLBI are specifically designed to be built in.

 Models CM405, CM411L and CM421BL: When installing, allow 5 inches of space

at the back and sides of the unit, which will allow the proper air circulation to cool

the compressor and condenser.

Improper use of the grounded plug can result in the risk of electrical shock. If the power

cord is damaged, have it replaced by an authorized service center.



Models CM405BI, CM411LBI and CM421BLBI: These built-in models are designed

to be installed under the counter in a 21-inch opening. When installing, provide the

following clearances to ensure the best operation and proper ventilation: 1/4” on

both sides, 2” at the rear and 1/16” at the top. Be sure that airflow under the

appliance is not blocked. If the appliance is going to be placed against a wall, if

possible, leave extra space on the hinge side so the door can open wider than its

width (to make it easier to remove shelves and crisper drawer).

 Locate the unit away from direct sunlight and sources of heat (stove, heater,

radiator, etc.). Direct sunlight may affect the acrylic coating and heat sources may

increase electrical consumption. Extremely cold ambient temperatures may also

affect the unit's performance.

 Avoid locating the unit in moist areas.

 Plug the unit into an exclusive, properly installed and grounded wall outlet. Do not

under any circumstances cut or remove the third (ground) prong from the power

cord. Any questions concerning power and/or grounding should be directed

toward a certified electrician or authorized service center.

 After plugging the appliance into a wall outlet, allow the unit to cool down for 2 to

3 hours before placing food in the refrigerator compartment.

Electrical Connection

This unit should be properly grounded for your safety. The power cord of this unit is

equipped with a three-prong plug which mates with a standard three-prong wall

outlet to minimize the possibility of electrical shock. Do not under any circumstances

cut or remove the third ground prong from the power cord supplied. For personal

safety, this appliance must be properly grounded.

This unit requires a standard 115-volt AC/60Hz electrical outlet with three-prong

ground. Have the wall outlet and circuit checked by a qualified electrician to make

sure the outlet is properly grounded. When a standard 2-prong wall outlet is

encountered, it is your responsibility and obligation to have it replaced with a

properly grounded 3-prong wall outlet.

To prevent accidental injury, the cord should be secured behind the unit and not left

exposed or dangling.

The unit should always be plugged into its own individual electrical outlet which has

a voltage rating that matches the rating label on the appliance. This provides the

best performance and also prevents overloading house wiring circuits that could

cause a fire hazard from overheated wires. Never unplug the unit by pulling on the

power cord. Always grip the plug firmly and pull straight out from the receptacle.

Repair or replace immediately any power cord that has become frayed or otherwise

damaged. Do not use a cord that shows cracks or abrasion damage along its length

or at either end. When moving the unit, be careful not to damage the power cord.

Extension Cord

: Do not use an extension cord. If the power cord is too short, have

a qualified electrician or service technician install an outlet near the appliance.

Reversing the Door Swing:

Figure 1 (Default position) Figure 2 (After door reversal)

1. Upper hinge cover 6. Screws

2. Screws 7. Hole cover

3. Upper hinge 8. Cabinet

4. Door 9. Pin cap

5. Lower door hinge

This refrigerator can be opened from either the right side or the left. By default, the door

hinge is on the right side. If you prefer it on the left, please follow these instructions:

NOTE: All of the parts that are removed must be kept for the reinstallation of the door.

1. Remove the three screws (6) holding lower door hinge (5). Keep hinge for later use.

2. Remove the door from the upper hinge (3), and keep the padded surface upward to

prevent scratching.

3. Remove the upper hinge cover (1), remove the two screws (2), remove the upper

hinge (3) and keep it for later use.

4. Remove the hole cover (7) and transfer it to the same location on the opposite side.

5. Insert the lower door hinge (5) into the left side, fixing the hinge into place by

tightening all the screws (6).

6. Remove the pin cap (9) from the left side of the upper door frame and then transfer it

to the same location on the opposite side.

7. Set the door on the lower door hinge (5), keep the door level, then fix the upper hinge

(3) to the body (8) by the screws (2).

8. Put on the upper hinge cover (1).

Door Handle Installation:

The door has two screw holes on each side, allowing you to install a handle (included).

To do so, align the handle with the screw holes on the side you prefer. Fix the handle in

place with the included screws, then cover the screw heads with the handle seal

(included).

Operating Your Refrigerator

Setting the Temperature Control

 Your unit has only one control for regulating the temperature in the

compartment. The temperature control is located on the upper right-hand side

of the compartment.



When turning the unit on for the first time, set the control to its coldest setting,

 The range of the temperature control is from the Off position to 6. After 24 to

48 hours, adjust the temperature control to the setting that best suits your

needs. The setting 3 should be appropriate for home or office use.

 To turn the appliance off, turn the temperature control to Off.

NOTES:

1. Turning the temperature control to Off stops the cooling cycle but does not

shut off the power to the unit.

2. If the unit is unplugged, has lost power, or is turned off, you must wait 3 to 5

minutes before restarting the unit. If you attempt to restart before this time

delay, the unit will not start.

Using Your Ice Cube Tray:

 The recommended thermostat setting for ice making is position 6.

 Fill the ice cube tray two-thirds full of cold water or with any liquid suitable for

freezing and place the tray on the floor of the chiller compartment to freeze

properly. Be sure to dry the bottom of the tray, or it may stick to the floor of the

chiller compartment.

 The best way to get ice cubes out of the tray is to hold the tray under cold tap

water for a second, then gently twist the tray over an ice bucket to eject the

cubes.

The Chiller Compartment

 This compartment is designed for production of ice cubes and for short-term

storage (3-4 days at most) of commercially frozen foods.

 The temperature in the compartment does not get cold enough to freeze food

safely for long periods of time and works best when the food is already frozen.

 By design, this compartment is not a true freezer and may not keep ice cream

frozen, or freeze items.

 A colder setting may be used for these items, but other items in the refrigerator

may also be affected.

 The chiller door is susceptible to breaking due to excessive ice buildup. This

part is not covered under your warranty. Be sure to defrost when the ice

reaches 1/4 inch thick.

Care and Maintenance

Defrosting Your Refrigerator:

1. Defrost the unit when the frost accumulating on the evaporator reaches a

thickness of about 1/4 inch. Turn the thermostat setting to Off.

2. Remove frozen or perishable foods from the chiller compartment and place

them in a cooler to protect the food.

3. During the defrost cycle, the ice melts into the drip tray.

4. To remove the water, empty the drip tray. Another collection container may be

placed under the freezer compartment in the meantime.

5. Use a sponge or towel to pick up the melting ice off the floor of the chiller

compartment. Never use a knife or other metal instrument to scrape ice/frost

from the evaporator.

6. Dry the water collection tray and place it back under the chiller compartment.

7. Defrosting usually takes a few hours. After defrosting, return the thermostat

dial to the desired position.

8. To defrost quickly, a container of warm water may be placed inside the chiller

compartment.

CAUTION: Do not use boiling water because it may damage the plastic parts.

In addition, using a sharp or metallic instrument to remove frost may

damage the cooling system and will void the warranty. We recommend

using a plastic scraper.

Cleaning Your Refrigerator:

1. Turn the temperature control to Off, unplug the unit and remove the food,

shelves and drip tray.

2. Wash the inside surfaces with a solution of warm water and baking soda. The

solution should contain about 2 tablespoons of baking soda to a quart of

water.

3. Wash the shelves and tray with a mild detergent solution.

4. Wash the outside cabinet with warm water and mild liquid detergent. Rinse

well and wipe dry with a clean soft cloth.

5. Wring excess water out of the sponge or cloth before cleaning the area of the

controls, or any electrical parts.

CAUTION

: Failure to unplug the unit could result in electrical shock or personal

injury.

Power Failure:

Most power failures are corrected within a few hours and should not affect the

temperature of your unit if you minimize the number of times the door is opened.

If the power is going to be off for a longer period of time, you need to take proper

steps to protect your food.

Vacation Time:

Short vacations: Leave the unit operating during vacations of less than three

weeks.

Long vacations: If the appliance will not be used for several months, remove all

food and unplug the power cord. Clean and dry the interior thoroughly. To

prevent odor and mold growth, leave the door open slightly, blocking it open if

necessary.

Moving Your Unit:

1. Remove all the food.

2. Securely tape down all loose items inside your unit.

3. Turn the leveling legs up to the base to avoid damage.

4. Tape the door shut.

5. Be sure the unit stays secure in the upright position during transportation.

Also, protect the outside of the unit with a blanket or similar covering.

Energy-Saving Tips:

 The unit should be located in the coolest area of the room, away from heat-

producing appliances and out of direct sunlight.

 Let hot foods cool to room temperature before placing in the unit. Overloading

the unit forces the compressor to run longer.

 Be sure to wrap foods properly and wipe containers dry before placing them in

the unit. This cuts down on frost build-up inside the unit.

 The unit's storage area should not be lined with aluminum foil, wax paper or

paper toweling. Liners interfere with cold air circulation, making the unit less

efficient.

 Organize and label food to reduce door openings and extended searches.

Remove as many items as needed at one time, and close the door as soon as

possible.

Problems with Your Refrigerator?

You can easily solve many common problems with your refrigerator, saving you

the cost of a possible service call. Try the suggestions below to see if you can

correct the problem before calling the service provider.

TROUBLESHOOTING GUIDE

Problem Possible Cause

Unit does not operate. Not plugged in.

The circuit breaker has tripped or the fuse

has blown.

The unit's temperature control is set at Off.

Turns on and off frequently. Room temperature is warmer than usual.

A large amount of food has been added to

the unit.

The door is opened too often.

The door is not closed completely.

The temperature control is not set correctly.

The door gasket does not seal properly.

The unit does not have the correct

clearances.

Vibrations Check to be sure the unit is level.

The unit seems to be making too

much noise.

A rattling noise may come from the flow of

refrigerant, which is normal.

As each cycle ends, you may hear gurgling

sounds caused by the flow of refrigerant

in your unit.

Contraction and expansion of the inside

walls may cause popping and crackling

noises.

The unit is not level.

The door will not close properly. The unit is not level.

The door was reversed and not properly

re-installed.

The gasket is dirty or bent.

The shelves or the crisper are out of

position.

For parts and accessory ordering,

troubleshooting and helpful hints, visit:

www.summitappliance.com/support

Limited Warranty

ONE-YEAR LIMITED WARRANTY

Within the 48 contiguous United States, for one year from the date of purchase, when this appliance is

operated and maintained according to instructions attached to or furnished with the product, warrantor will

pay for factory-specified parts and repair labor to correct defects in materials or workmanship. Service must

be provided by a designated service company. Outside the 48 states, all parts are warranted for one year

from manufacturing defects. Plastic parts, shelves and cabinets are warranted to be manufactured to

commercially acceptable standards, and are not covered from damage during handling or breakage.

5-YEAR COMPRESSOR WARRANTY

1. The compressor is covered for 5 years.

2. Replacement does not include labor.

ITEMS WARRANTOR WILL NOT PAY FOR:

1. Service calls to correct the installation of your appliance, to instruct you how to use your appliance, to

replace or repair fuses or to correct wiring or plumbing.

2. Service calls to repair or replace appliance light bulbs or broken shelves. Consumable parts (such as

filters) are excluded from warranty coverage.

3. Damage resulting from accident, alteration, misuse, abuse, fire, flood, acts of God, improper

installation, installation not in accordance with electrical or plumbing codes, or use of products not

approved by warrantor.

4. Replacement parts or repair labor costs for units operated outside the United States.

5. Repairs to parts or systems resulting from unauthorized modifications made to the appliance.

6. Expenses for travel and transportation for product service in remote locations.

7. The removal and reinstallation of your appliance if it is installed in an inaccessible location or is not

installed in accordance with published installation instructions.

DISCLAIMER OF IMPLIED WARRANTIES – LIMITATION OF REMEDIES

CUSTOMER'S SOLE AND EXCLUSIVE REMEDY UNDER THIS LIMITED WARRANTY SHALL BE

PRODUCT REPAIR AS PROVIDED HEREIN. IMPLIED WARRANTIES, INCLUDING WARRANTIES OF

MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE, ARE LIMITED TO ONE YEAR.

WARRANTOR SHALL NOT BE LIABLE FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES. SOME

STATES DO NOT ALLOW THE EXCLUSION OR LIMITATION OF INCIDENTAL OR CONSEQUENTIAL

DAMAGES, OR LIMITATIONS ON THE DURATION OF IMPLIED WARRANTIES OF MERCHANTABILITY

OR FITNESS, SO THESE EXCLUSIONS OR LIMITATIONS MAY NOT APPLY TO YOU. THIS WARRANTY

GIVES YOU SPECIFIC LEGAL RIGHTS AND YOU MAY ALSO HAVE OTHER RIGHTS, WHICH VARY

FROM STATE TO STATE.

FELIX STORCH, INC.

770 Garrison Avenue

Bronx, NY 10474

Phone: (718) 893-3900

Fax: (718) 842-3093

www.summitappliance.com

WARNING! This product may contain chemicals known to the state of California

to cause cancer or birth defects or other reproductive harm. For more information,

visit: www.summitappliance.com/prop65

Chemicals known by the manufacturer to be present in this product in concentrations

her than threshold limits: NONE.

Summit CM411LSSHH Owner's manual

Brand: Summit

Model: CM411LSSHH

Category: Fridges

Type: Owner's manual

This manual is also suitable for

Download PDF

report

Summit CM411LSSHH Owner's manual

This manual is also suitable for

Summit CM411LSSHH Owner's manual

Related papers

Other documents