ZyXEL NAP102 Owner's manual

Category
Security device components
Type
Owner's manual
www.zyxel.com
QUICK START GUIDE
NWA1100
802.11g Business WLAN
Access Point
Firmware v1.00
Edition 1, 07/2008
DEFAULT LOGIN DETAILS
IP Address: http://192.168.1.2
Password: 1234
CONTENTS
ENGLISH 3
DEUTSCH 19
ESPAÑOL 35
FRANÇAIS 51
ITALIANO 67
РУССКИЙ 83
SVENSKA 99
简体中文
115
繁體中文
129
Copyright 2008 ZyXEL Communications Corporation
C
2
Front and Base Panels
ENGLISH
ENGLISH
3
Overview
This Quick Start Guide shows how to set up and configure the NWA1100
(marked Z in the figure) to allow wireless clients to securely access your
wired network. See your User’s Guide for more information.
You may need your Internet access information.
To set up your wireless network you need to:
• Connect the Hardware
• Access the Web Configurator
• Configure the NWA1100
• Install the Hardware
• Set Up Power over Ethernet (Optional)
Z
ENGLISH
ENGLISH
4
Connect the Hardware
1. Using the grey Ethernet cable, connect the ETHERNET port to a computer
for initial configuration.
2. Connect the POWER 12VDC socket to a power source using only the
included power adaptor.
Connect the NWA1100’s ETHERNET port to an Ethernet jack with
network access after you have completed the initial configuration.
ENGLISH
ENGLISH
5
LEDs
• The SYS LED blinks amber, then turns steady green when the power is
connected.
• One of the LEDs by the ETHERNET port turns on if the port is properly
connected, and blinks when there is traffic. The amber light shines if the
connection is at 100 Mbps. The green light shines if the connection is at
10Mbps.
If neither LED near the ETHERNET port turns on, check the cable
connections to the port. Ensure your computer’s network card is
working properly.
ENGLISH
6
Access the Web Configurator
Use Internet Explorer 6.0 and later or Netscape Navigator 7.0 and later
versions with JavaScript enabled and pop-up blocking disabled.
Set Up Your Computers IP Address
Note down your computer’s current IP settings before you change
them.
First, set your computer to use a static IP address in the 192.168.1.3 -
192.168.1.254 range with a subnet mask of 255.255.255.0. This ensures that
your computer can communicate with your NWA1100. See your User’s Guide
for information on setting up your computer’s IP address.
ENGLISH
ENGLISH
7
Log Into the Web Configurator
Even though you can connect to the NWA1100 wirelessly, it is
recommended that you connect your computer to the ETHERNET port
for initial configuration.
1. Launch your web browser.
Enter 192.168.1.2 (the
NWA1100’s default IP address)
as the address.
If you cannot access the Web configurator, make sure the IP
addresses and subnet masks of the NWA1100 and the computer
are in the same IP address range.
2. Enter 1234 (the default
password) in the Password
field and click Login.
ENGLISH
8
3. Change the login password by
entering a new password and
clicking Apply. Be sure to
record the new password and
keep it in a safe place.
If you change the password and then forget it, you will need to
reset the NWA1100. Refer to the User’s Guide for how to use the
RESET button.
4. The STATUS screen appears.
ENGLISH
ENGLISH
9
Configure the NWA1100
Configure System Settings
1. Click SYSTEM in the navigation panel.
2. The SYSTEM > General screen appears.
ENGLISH
10
System Name is for identifying the NWA1100 on your network. Choose a
distinctive name, or leave this at its default.
DNS Server(s): if your ISP gave you specific DNS (Domain Name
System) settings, select User-Defined and enter them here. Otherwise,
leave these fields at their defaults.
3. Click Apply.
ENGLISH
ENGLISH
11
Configure Wireless Settings
1. Click WIRELESS
in the navigation
panel. The
Wireless
Settings screen
displays.
The wireless stations and the NWA1100 must use the same SSID,
channel ID and encryption settings for wireless communication.
Operation Mode: Ensure that AP mode is selected.
Wireless Mode: Select the wireless standard you want your network to
use. If you are not sure which to select, select 802.11b+g.
Channel: Select the wireless channel you want your network to use.
2. Click Apply to save your settings.
ENGLISH
12
3. Click the
Security tab. If
you don’t
configure
wireless security,
anyone can
access your
network.
This is where you can enter the security settings for your wireless
network. The fields you fill in differ according to the type of security you
select in the Security Mode field. Select None if you do not wish to use
wireless security.
This example uses WPA2-PSK security, in which all wireless clients must
use the same pre-shared key to join the network.
Ensure that all your wireless clients support the type of security you set.
Click Apply when you have finished.
If the wireless clients cannot communicate with the network,
ensure that the clients and the NWA1100 are using the same
wireless security settings.
ENGLISH
ENGLISH
13
Configure IP Settings
1. You need to set your
NWA1100’s IP address to
be in the same subnet as
your network. Click IP in
the navigation panel.
Select Get automatically
from DHCP if you want to
have a DHCP server on
your network assign an IP
address to the NWA1100.
If you have a specific IP
address to use, select
Use fixed IP address
and enter it along with the
subnet mask and gateway
IP address.
Click Apply. The
NWA1100 now uses the
new IP settings; you can
no longer connect to the
NWA1100 using the
default IP address.
ENGLISH
14
The NWA1100 is now ready to connect to your switch or router. You can do
this now, or once you have attached the antennas and mounted the
NWA1100.
If the NWA1100 cannot communicate with the network, ensure
that the NWA1100 is using an IP address on the same subnet as
the switch / router.
If you change the NWA1100’s IP address, you must use the new IP
address when you next access the web configurator. If you select Get
automatically from DHCP, check your DHCP server to determine the IP
address it assigns to the NWA1100. Refer to your DHCP server’s
documentation for more information.
2. If you changed your computer’s IP address, return it to its previous
setting.
3. Change the wireless settings in the wireless stations to match those of
the NWA1100, if necessary. Refer to your wireless adapter’s
documentation.
ENGLISH
ENGLISH
15
Install the Hardware
Figures in this section use generic icons. The ZyXEL Device in the picture is
not an exact representation of your device.
Attaching Antennas
Hardware Mounting
In general, the best location for the access point is at the center of your
intended wireless coverage area. For better performance, mount the
NWA1100 high up in an area that is free of obstructions.
Wall-mounting
Do the following to attach your NWA1100 to a wall.
Screw the antennas clockwise onto the antenna
connectors on the sides of your NWA1100. The
antennas should be perpendicular to the ground and
parallel to each other.
Make sure the antennas are securely screwed onto the
antenna connectors.
ENGLISH
16
1. Screw the two screws provided with your NWA1100 into the wall 60mm
apart (see the figure in step 3). Use screws with 6mm ~ 8mm (0.24" ~
0.31") wide heads. Do not screw the screws all the way in to the wall;
leave a small gap between the head of the screw and the wall.
The gap must be big enough for the screw heads to slide into the screw
slots and the connection cables to run down the back of the NWA1100.
Make sure the screws are securely fixed to the wall and strong enough
to hold the weight of the NWA1100 with the connection cables.
ENGLISH
ENGLISH
17
2. Adjust the cables.
Run the connection cables down the back of the NWA1100 as shown in
the following figure.
OR:
Run the connection cables upward and along the edge of the ceiling.
3. Align the holes on the
back of the NWA1100
with the screws on the
wall. Hang the
NWA1100 on the
screws.
6
0
m
m
ENGLISH
18
Set Up Power over Ethernet
(Optional)
Power over Ethernet (PoE) is the ability to provide power to your NWA1100
via an 8-pin CAT 5 Ethernet cable, eliminating the need for a nearby power
source.
A PoE injector (not included) is also needed to supply the Ethernet cable with
power. This feature allows increased flexibility in the location of your
NWA1100.
In the following figure, Z is your NWA1100, A is the CAT 5 Ethernet cable, B
is the PoE injector and C is the power cable.
ENGLISH
122
配置无线设置
1. 在导航面板中单
WIRELESS (
线)。此时会显示
下列屏幕。显示
Wireless Settings
(无线设置)
幕。
无线客户端与 NWA1100 必须使用相同的 SSID、频道 ID 和无线通信加密设
置。
WLAN Adaptor ( 广域网适配器 ):确保已经选择 WLAN1
Operation Mode ( 操作模式 )确保已选中 Access Point ( 访问点 )
式。
Wireless Mode ( 无线模式 ): 选择网络欲采用的无线标准。如果您不确
定选择哪一个,则选择 802.11b+g.
Channel ( 选择频道 ):选择网络欲采用的无线频道。
2. 单击 Apply ( 应用 ) 以保存设置。
ENGLISH
ENGLISH DEUTSCH ESPAÑOL
Viewing a Product’s Certification(s)
• Go to www.zyxel.com.
• Select your product from the drop-down list
box on the ZyXEL home page to go to that
product's page.
• Select the certification you wish to view from
this page.
Vorgehensweise zum Aufrufen einer
Produktzertifizierung
• Gehen Sie auf www.zyxel.com.
• Wählen Sie Ihr Produkt aus der Auswahlliste
auf der ZyXEL Homepage aus, um die Seite
des entsprechenden Produkts aufzurufen.
• Wählen Sie die Zertifizierung, die Sie von
dieser Seite aus aufrufen möchten.
Procedimiento para ver las
certificaciones de un producto
• Vaya a www.zyxel.com.
• Seleccione el producto que desea en el
cuadro de lista desplegable que se encuentra
en la página principal de ZyXEL para obtener
acceso a la página de dicho producto.
• Seleccione la certificación que desea ver en
esta página.
FRANÇAIS ITALIANO NEDERLANDS
Procédure permettant de consulter
une(les) Certification(s) du Produit
• Connectez vous sur www.zyxel.com.
• Sélectionnez votre produit dans la liste
déroulante se trouvant sur la page d'accueil
ZyXEL pour accéder à la page du produit
concerné.
• Sélectionnez sur cette page la certification
que vous voulez consulter.
Procedura per visualizzare le
certificazioni di un prodotto
• Andare alla pagina www.zyxel.com
• Nel sito ZyXEL, selezionare il proprio
prodotto dall’elenco a discesa per andare alla
pagina di quel prodotto.
• Da questa pagina selezionare la
certificazione che si vuole vedere.
Procedure voor het opvragen en het
inzien van product certificering(en)
• U gaat met uw browser naar de website:
www.zyxel.com
• U kunt nu de product pagina opvragen door
op de ZyXEL thuispagina het product te
selecteren uit de lijst
• Nu selecteert u de certificering die u wilt
inzien
SVENSKA РУССКИЙ
日本語
Procedur för att visa en produkts
certifikat
• Gå till www.zyxel.com
• Välj din produkt från rullgardinslistrutan på
ZyXEL:s hemsida för att gå till denna produkts
sida.
• Välj det certifikat du vill titta på från denna
sida.
Просмотр сертификата(ов)
продукта(ов)
Посетите сайт www.zyxel.com.
Выберите ваш продукт из выпадающего
списка на домашней странице ZyXEL и
перейдите на его страницу.
Выберите сертификат, который вы хотите
просмотреть.
製品情報をご覧になるには
・ www.zyxel.com へアクセスします。
・ ZyXEL のホームページにあるドロップダウンリスト
からご利用の製品を選択し、製品ページを開きます。
・ このページで製品保証についてご覧ください。
简体中文 繁體中文
查看产品的认证
* 访问 www.zyxel.cn。
* ZyXEL 首页的下拉列表框中选择您所购买的
产品以前往该产品的相关网页。
* 在该网页选择您想要查看的认证。
檢視產品的認證
* 前往 www.zyxel.com
* ZyXEL 首頁的下拉式清單方塊中選擇您所購
買的產品以前往產品的相關網頁。
* 由此網頁選擇您想要檢視的認證 °
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42
  • Page 43 43
  • Page 44 44
  • Page 45 45
  • Page 46 46
  • Page 47 47
  • Page 48 48
  • Page 49 49
  • Page 50 50
  • Page 51 51
  • Page 52 52
  • Page 53 53
  • Page 54 54
  • Page 55 55
  • Page 56 56
  • Page 57 57
  • Page 58 58
  • Page 59 59
  • Page 60 60
  • Page 61 61
  • Page 62 62
  • Page 63 63
  • Page 64 64
  • Page 65 65
  • Page 66 66
  • Page 67 67
  • Page 68 68
  • Page 69 69
  • Page 70 70
  • Page 71 71
  • Page 72 72
  • Page 73 73
  • Page 74 74
  • Page 75 75
  • Page 76 76
  • Page 77 77
  • Page 78 78
  • Page 79 79
  • Page 80 80
  • Page 81 81
  • Page 82 82
  • Page 83 83
  • Page 84 84
  • Page 85 85
  • Page 86 86
  • Page 87 87
  • Page 88 88
  • Page 89 89
  • Page 90 90
  • Page 91 91
  • Page 92 92
  • Page 93 93
  • Page 94 94
  • Page 95 95
  • Page 96 96
  • Page 97 97
  • Page 98 98
  • Page 99 99
  • Page 100 100
  • Page 101 101
  • Page 102 102
  • Page 103 103
  • Page 104 104
  • Page 105 105
  • Page 106 106
  • Page 107 107
  • Page 108 108
  • Page 109 109
  • Page 110 110
  • Page 111 111
  • Page 112 112
  • Page 113 113
  • Page 114 114
  • Page 115 115
  • Page 116 116
  • Page 117 117
  • Page 118 118
  • Page 119 119
  • Page 120 120
  • Page 121 121
  • Page 122 122
  • Page 123 123
  • Page 124 124
  • Page 125 125
  • Page 126 126
  • Page 127 127
  • Page 128 128
  • Page 129 129
  • Page 130 130
  • Page 131 131
  • Page 132 132
  • Page 133 133
  • Page 134 134
  • Page 135 135
  • Page 136 136
  • Page 137 137
  • Page 138 138
  • Page 139 139
  • Page 140 140
  • Page 141 141
  • Page 142 142
  • Page 143 143
  • Page 144 144

ZyXEL NAP102 Owner's manual

Category
Security device components
Type
Owner's manual

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI