Indesit CAA 55 NX User guide

Page is loading ...

GB

REFRIGERATOR/FREEZER COMBINATION

Operating Instructions

Contents

Installation, 12-13

Positioning and connection

Door reversal

Description of the appliance, 14

Overall view

Start-up and use, 15-16

Starting the appliance

Using the refrigerator to its full potential

Using the freezer to its full potential

Maintenance and care, 17

Switching the appliance off

Cleaning the appliance

Avoiding mould and unpleasant odours

Replacing the light bulb

Precautions and tips, 18

General safety

Disposal

Respecting and conserving the environment

Troubleshooting, 19

Assistance, 20

Italiano, 1 English, 11

GBI

Portuges, 31

P

Espanol, 21

E

Română, 41

RO

Polski,

51

PL

CA 55 NX

CAA 55 NX

Magyar, 61

HU

Česky, 71

CZ

Français, 81

F

GB

12

Installation

! Before placing your new appliance into operation

please read these operating instructions carefully. They

contain important information for safe use, for installation

and for care of the appliance.

! Please keep these operating instructions for future

reference. Pass them on to possible new owners of the

appliance.

Positioning and connection

Positioning

1. Place the appliance in a well-ventilated humidity-free

room.

2. Do not obstruct the rear fan grills. The compressor and

condenser give off heat and require good ventilation to

operate correctly and save energy.

3. Leave a space of at least 10 cm between the top part

of the appliance and any furniture above it, and at least

5 cm between the sides and any furniture/side walls.

4. Ensure the appliance is away from any sources of heat

(direct sunlight, electric stove, etc.).

5. In order to maintain the correct distance between

the appliance and the wall behind it, fit the spacers

supplied in the installation kit, following the instructions

provided.

Levelling

1. Install the appliance on a level and rigid floor.

2. If the floor is not perfectly horizontal, make the

necessary adjustments by tightening or loosening the

single foot at the front of the appliance.

Electrical connections

After the appliance has been transported, carefully place

it vertically and wait at least 3 hours before connecting it

to the electricity mains. Before inserting the plug into the

electrical socket ensure the following:

• The appliance is earthed and the plug is compliant

with the law.

• The socket can withstand the maximum power of the

appliance, which is indicated on the data plate located

on the bottom left side of the fridge (e.g. 150 W).

• The voltage must be in the range between the values

indicated on the data plate located on the bottom left

side (e.g. 220-240V).

• The socket is compatible with the plug of the

appliance.

If the socket is incompatible with the plug, ask an

authorised technician to replace it (see Assistance).

Do not use extension cords or multiple sockets.

! Once the appliance has been installed, the power

supply cable and the electrical socket must be easily

accessible.

! The cable must not be bent or compressed.

! The cable must be checked regularly and replaced by

authorised technicians only (see Assistance).

! The manufacturer declines any liability should these

safety measures not be observed.

GB

13

DOOR REVERSAL

Warning: Before attempting to remove the doors, switch off the electrical supply and pull out the mains plug.

It is recommended that you remove any loose items/fittings from inside the appliance and place food into insulated containers whilst

carrying out this operation.

You may require assistance to carefully lay the appliance onto its back onto suitable protective materials (i.e. original packaging).

Remove the doors

1. Lay down the appliance on its

back.

2. Unscrew, remove and retain the

bottom hinge.

3. Slightly open the bottom door

and slide downward remove and

carefully place to one side

4. Remove centre hinge and spacer

if fitted.

Slightly open the top door

and slide downwards, remove and

carefully place to one side.

5. The pin will be removed and fixed

to the

opposite side

6. Use a thin blunt instrument to

remove the top and bottom hinge

bushes and blanking plugs from

the doors, take care not to mark

the door handle. Reposition the

blanking plugs and bushes on the opposite side.

7. Fit the blanking plugs provided into the right hand two centre hinge holes.

8. Before changing hinge place from right side to left side, screw on left side panel should be disassemblied and after changing

hinge place, screw should be assemblied on right side panel.

Replacing the doors

1. Slide the top door upwards and locate the top hinge pin into the door bush. Reposition the centre hinge on the opposite side.

2. Carefully slide bottom door upward into the centre hinge pin.

3. Unscrew the bottom hinge pin and

refit it on the opposite side..

4. Fit the bottom hinge making sure that

the door is aligned to the cabinet.

5. Carefully stand the appliance upright

in it’s required location and make

sure it is sitting level on the floor.

Open and close the doors checking

that the gasket makes a good seal

without any gaps when the doors are

closed.

Note: Replace loose items/fittings back

into the appliance and leave for at least

15 minutes before switching back on.

GB

14

Description of the

appliance

TEMPERATURE

REGULATING

Knob

SHELVES

•

FRUIT and

VEGETABLE bin

FREEZER and

STORAGE

compartment

STORAGE

compartment

ICE tray

•

Removable lidded shelf

with EGG TRAY

*

Removable

multipurpose

SHELVES•

BOTTLE shelf

Compartment for a

2 LITRE BOTTLE

Levelling FOOT

Overall view

The instructions contained in this manual are applicable to different model refrigerators. The diagrams may not directly represent

the appliance purchased. For more complex features, consult the following pages.

There is only one adjustable foot.

• Varies by number and/or position.

* Available only on certain models.

GB

15

Start-up and use

Starting the appliance

! Before starting the appliance, follow the installation

instructions (see Installation).

! Before connecting the appliance, clean the compartments and

accessories well with lukewarm water and bicarbonate.

1. Insert the plug into the socket and ensure that the internal

light illuminates.

2. Turn the TEMPERATURE ADJUSTMENT knob to an average

value. After a few hours you will be able to put food in the

refrigerator.

Using the refrigerator to its full potential

The temperature inside the refrigerator compartment

automatically adjusts itself according to the position of the

thermostat knob.

1 = warmest 5 = coldest

We recommend, however, a medium position.

The cooling section of the refrigerator is located inside the

back wall of the refrigerator compartment for increased space

and improved aesthetics. During operation, the back wall will

be covered in frost or water droplets depending on whether

the compressor is operating or paused. Do not worry, the

refrigerator is functioning normally.

If the TEMPERATURE ADJUSTMENT knob has been set on

high values with large quantities of food and with a high ambient

temperature, the appliance can operate continuously, resulting

in excessive frost formation and excessive energy consumption:

compensate for this by shifting the knob towards lower values

(defrosting will occur automatically).

In static appliances, the air circulates in a natural way: the

colder air tends to move downwards as it is heavier. The food

should be stored as follows:

Food

Arrangement inside the

refrigerator

Fresh fish and meat

Above the fruit and vegetable bins

Fresh cheese

Above the fruit and vegetable bins

Cooked food

On any shelf

Salami, loaves of bread,

chocolate

On any shelf

Fruit and vegetables

In the fruit and vegetable

compartment bins

Eggs

On the shelf provided

Butter and margarine

On the shelf provided

Bottles, drinks, milk

On the shelves provided

• Place only cold or lukewarm foods in the compartment, not

hot foods (see Precautions and tips).

• Remember that cooked foods do not last longer than raw

foods.

• Do not store liquids in open containers. They will increase

humidity in the refrigerator and cause condensation to form.

SHELVES: with or without grill.

Due to the special guides the shelves are removable and

the height is adjustable (see diagram), allowing easy storage

of large containers and food. Height can be adjusted without

complete removal of the shelf.

TEMPERATURE Indicator light

*: to identify the coldest area in

the refrigerator.

1. Check that OK appears clearly on the indicator light (see

diagram).

2. If the word “OK” does not appear it means that the

temperature is too high: adjust the REFRIGERATOR

OPERATION knob to a higher position (colder) and wait

approximately 10 hours until the temperature has been

stabilised.

3. Check the indicator light again: if necessary, readjust it

following the initial process. If large quantities of food have

been added or if the refrigerator door has been opened

frequently, it is normal for the indicator not to show OK.

Wait at least 10 hours before adjusting the REFRIGERATOR

OPERATION knob to a higher setting.

GB

16

Using the freezer to its full potential

• Do not re-freeze food that is defrosting or that has already

been defrosted. These foods must be cooked and eaten

(within 24 hours).

• Fresh food that needs to be frozen must not come into

contact with food that has already been defrosted.

Fresh food must be stored above the grill in the freezer

compartment and if possible be in direct contact with the

walls (side and rear), where the temperature drops below

-18°C and guarantees rapid freezing.

• Do not place glass bottles which contain liquids, and which

are corked or hermetically sealed in the freezer because

they could break.

• The maximum quantity of food that may be frozen

daily is indicated on the plate containing the technical

properties located on the bottom left side of the refrigerator

compartment (for example: Kg/24h: 4)

• In order to obtain a greater amount of space in the freezer

compartment, you may remove the bins (except the lowest

bin and the special COOL CARE ZONE bin, which has an

adjustable temperature) and place the food directly onto the

evaporator plates.

! Do not open the door during freezing.

! If there is a power cut or malfunction, do not open the freezer

door. This will help maintain the temperature inside the freezer,

ensuring that foods are conserved for at least 9 -14 hours.

! If the room temperature drops below 14°C for an extended

period of time, the ideal temperature will not be reached in the

freezer compartment and food preservation will be reduced.

Ice tray

The fact that they are situated on the top part of the freezer

drawers ensures greater cleanliness: the ice no longer

comes into contact with the food placed inside the freezer

compartment; furthermore, the dripping of the water during

filling is avoided (a lid to cover up the hole after filling with water

is also provided).

1. Pull out the tray by pushing it up.

Check that the tray is completely empty and fill it with water

through the opening provided.

2. Take care not to exceed the level indicated (MAX WATER

LEVEL). Excess water prevents the ice cubes from dispensing

(if this happens, wait for the ice to melt and empty the tray).

3. Turn the tray 90°: due to the connected compartments each

mould fills with water (see diagram).

4. Close the opening with the lid provided and put the tray back.

5. When the ice has formed (minimum time approximately 8

hours) knock the tray against a hard surface and wet the

outside so that the ice cubes come loose and take them out

through the opening.

MAX

WATER LEVEL

MAX

WATER LEVEL

GB

17

Maintenance and care

Switching the appliance off

During cleaning and maintenance it is necessary to disconnect

the appliance from the electricity supply:

It is not sufficient to set the temperature adjustment knobs on

(appliance off) to eliminate all electrical contact.

Cleaning the appliance

• The external and internal parts, as well as the rubber seals

may be cleaned using a sponge that has been soaked in

lukewarm water and bicarbonate of soda or neutral soap. Do

not use solvents, abrasive products, bleach or ammonia.

• The removable accessories may be soaked in warm water

and soap or dishwashing liquid. Rinse and dry them

carefully.

• The back of the appliance may collect dust which can be

removed by delicately using the hose of a vacuum cleaner

set on medium power. The appliance must be switched

off and the plug must be pulled out before cleaning the

appliance.

Avoiding mould and unpleasant odours

• The appliance is manufactured with hygienic materials which

are odour free. In order to maintain an odour free refrigerator

and to prevent the formation of stains, food must always be

covered or sealed properly.

• If you want to switch the appliance off for an extended period of

time, clean the inside and leave the doors open.

Defrosting the appliance

! Follow the instructions below.

Do not use objects with sharp or pointed edges to defrost the

appliance as these may damage the refrigeration circuit beyond

repair.

Defrosting the refrigerator compartment

The refrigerator has an automatic defrosting function: water is

ducted to the back of the appliance by a special discharge

outlet (see diagram) where the heat produced by the

compressor causes it to evaporate. It is necessary to clean the

discharge hole regularly so that the water can flow out easily.

Defrosting the freezer compartment

If the frost layer is greater than 5 mm, it is necessary to defrost

manually:

1. Set the TEMPERATURE ADJUSTMENT knob to the position

.

2. Wrap frozen foods in newspaper and place them in another

freezer or in a cool place.

3. Leave the door open until the frost has melted completely.

This can be made easier by placing containers with lukewarm

water in the freezer compartment.

4. Clean and dry the freezer compartment carefully before

switching the appliance on again.

5. Certain appliances are fitted with the DRAIN SYSTEM

to lead the water outside: let the water flow into a

container (see diagram).

6. Wait for approximately 2 hours, i.e. until the ideal storage

conditions have been restored, before placing food in the

freezer compartment.

Replacing the light bulb

To replace the light bulb in the refrigerator compartment, pull

out the plug from the electrical socket. Follow the instructions

below.

Access the light bulb by removing the cover as indicated in the

diagram. Replace it with a similar light bulb within the power

range indicated on the cover (15W or 25W).

GB

18

Precautions and tips

! The appliance was designed and manufactured in compliance

with international safety standards. The following warnings are

provided for safety reasons and must be read carefully.

This appliance complies with the following Community

Directives:

- 73/23/EEC of 19/02/73 (Low Voltage) and subsequent

amendments;

-89/336/EEC of 03.05.89 (Electromagnetic

Compatibility) and subsequent amendments;

- 2002/96/CE..

General safety

• The appliance was designed for domestic use inside the home

and is not intended for commercial or industrial use.

• The appliance must be used to store and freeze food products

by adults only and according to the instructions in this manual.

• The appliance must not be installed outdoors, even in covered

areas. It is extremely dangerous to leave the appliance exposed

to rain and storms.

• Do not touch the appliance with bare feet or with wet or moist

hands and feet.

• Do not touch the internal cooling elements: this could cause

skin abrasions or frost/freezer burns.

• When unplugging the appliance always pull the plug from the

mains socket, do not pull on the cable.

• Before cleaning and maintenance, always switch off the

appliance and disconnect it from the electrical supply. It is

not sufficient to set the temperature adjustment knobs on

(appliance off) to eliminate all electrical contact.

• In the case of a malfunction, under no circumstances should

you attempt to repair the appliance yourself. Repairs carried

out by inexperienced persons may cause injury or further

malfunctioning of the appliance.

• Do not use any sharp or pointed utensils or electrical

equipment - other than the type recommended by the

manufacturer - inside the frozen food storage compartments.

• Do not put ice cubes taken directly from the freezer into your

mouth.

• This appliance is not intended for use by persons (including

children) with reduced physical, sensory or lack of experience

and knowledge unless they have been given supervision

or instruction concerning use of the appliance by a person

responsible for their safety. Children should be supervised to

ensure that they do not play with the appliance.

• Keep packaging material out of the reach of children! It can

become a choking or suffocation hazard.

Disposal

• Observe local environmental standards when disposing

packaging material for recycling purposes.

• The European Directive 2012/19/EU on Waste Electrical and

Electronic Equipment (WEEE), requires that old household

electrical appliances must not be disposed of in the normal

unsorted municipal waste stream. Old appliances must be

collected separately in order to optimise the recovery and

recycling of the materials they contain and reduce the impact

on human health and the environment. The crossed out

“wheeled bin” symbol on the product reminds you of your

obligation, that when you dispose of the appliance it must be

separately collected.

Consumers may take their old appliance to public

waste collection areas, other communal collection

areas, or if national legislation allows return it to a

retailer when purchasing a similar new product.

All major household appliance manufacturers are

active in the creation of systems to manage the

collection and disposal of old appliances.

Respecting and conserving the environment

• Install the appliance in a fresh and well-ventilated room.

Ensure that it is protected from direct sunlight and do not

place it near heat sources.

• Try to avoid keeping the door open for long periods or

opening the door too frequently in order to conserve energy.

• Do not fill the appliance with too much food:

cold air must circulate freely for food to be preserved

properly. If circulation is impeded, the compressor will work

continuously.

• Do not place hot food directly into the refrigerator. The

internal temperature will increase and force the compressor

to work harder and will consume more energy.

• Defrost the appliance if ice forms (see Maintenance). A thick

layer of ice makes cold transference to food products more

difficult and results in increased energy consumption.

• Regularly check the door seals and wipe clean to ensure they

are free of debris and to prevent cold air from escaping (see

Maintenance).

GB

19

Troubleshooting

If the appliance does not work, before calling for Assistance (see Assistance), check for a solution from the following list.

Malfunctions:

The internal light does not illuminate.

The refrigerator and the freezer do not cool

well.

The food inside the refrigerator is

beginning to freeze.

The motor runs continuously.

The appliance makes a lot of noise.

Some of the external parts of the

refrigerator become hot.

The back wall of the refrigerator unit is

covered in frost or droplets of water.

There is water at the bottom of the

refrigerator.

Excess moisture / Ice at rear of the Fridge

Warm Fridge

Possible causes / Solutions:

• The plug has not been inserted into the electrical socket, or not far enough to make

contact, or there is no power in the house.

• The doors do not close properly or the seals are damaged.

• The doors are opened too frequently.

• The TEMPERATURE ADJUSTMENT knob is not in the correct position

• The refrigerator or the freezer have been over-filled.

• The atmospheric temperature of the area surrounding the appliance is lower than

14°C.

• The TEMPERATURE ADJUSTMENT knob is not in the correct position.

• The food is in contact with the back inside wall of the refrigerator.

• The door is not closed properly or is continuously opened.

• The outside ambient temperature is very high.

• The thickness of the frost exceeds 2-3 mm (see Maintenance).

• The appliance has not been installed on a level surface (see Installation).

• The appliance has been installed between cabinets that vibrate and make noise.

• The internal refrigerant makes a slight noise even when the compressor is off. This is

not a defect, it is normal.

• These raised temperatures are necessary in order to avoid the formation of

condensation on certain parts of the product.

• This shows the appliance is operating normally.

• The water discharge hole is blocked (see Maintenance).

• Excess moisture / Ice will occur if the Larder door is opened for prolonged periods.

This will disappear once the door is closed and the Larder allowed to defrost

and drain the moisture away. This is normal for cooling function of the Larder

compartment, especially in summer period.

• If room temperature is 16 C or lower, (for example the product is located in a garage

or out building), for the refrigerator to operate correctly the “Fast Freeze switch” must

be in the ‘ON’ position.

Switch

GB

20

Assistance

Before calling for Assistance:

• Check if the malfunction can be solved on your own (see Troubleshooting).

• If after all the checks, the appliance still does not operate or the problem persists, call the nearest Service Centre

Communicating:

• type of malfunction

• appliance model (Mod.)

• serial number (S/N)

This information can be found on the data plate

located on the bottom left side of the refrigerator

compartment.

Never call on unauthorized technicians and always refuse spare parts which are not originals.

model serial number

195083720.10

10/2014

Page is loading ...

Indesit CAA 55 NX User guide

Indesit CAA 55 NX User guide

in other languages

Related papers

Other documents