GE AGM24DHM1 Owner's manual

Brand: GE

Model: AGM24DHM1

Category: Mobile air conditioners

Type: Owner's manual

This manual is also suitable for

www. GEAppliances.com

Safety Instructions ........ 2, 3

Operating Instructions ..... 4, 5

Care and Cleaning

Air Fiher . ................. 6

Grille and Case ............. 6

Outdoor (;oils .............. 6

Installation Instructions

Preparing to Install the

Air Conditioner . ............ 7

Window Installation ....... 8-19

Troubleshooting Tips ... 13, 14

Normal ()perating Sounds . . .14

Consumer Support

Consumer Support ......... 18

Product Registration ..... 15, 16

_A'arranty ................. 17

A GM24

Write the model and serial numbers here:

Model #

Serial #

Find these nmnbers on a label on the

side of the air conditioner.

3828A20514H 49-7498 02-05JR

IMPORTANTSAFETYINFORMATION.

READALLINSTRUCTIONSBEFOREUSING.

a, WARNING!

For your safety;,the information in this manual must be followed to minimize the risk of fire, electric shock

or personal injury.

SAFETYPRECAUTIONS

iiiiiiiiiiii_iii

Use this appliance only %r its intended

pull)ose as described in this Owner's

Manual.

This air conditioner must be properly

installed in accordance with d_e Installation

h_structions before it is used.

Turn the mode control to 0fFand unplug

your air conditioner before making any

repairs or cleaning.

NOTE.'XA:estrongly recommend that any

servicing be perforated by a qualified

individual.

iiiiiiiiiiii_iii

Never unplug your air conditioner by

pulling on the power cord. Mwws grip

plug firefly and pull straight out from the

receptacle.

Replace immediamly all electric setMce

cords that haxe become flayed or ofl_erwise

damaged. Do not use a cord that shows

cracks or abrasion damag_ along its length

or at either the ping or connector end.

For your safety...do not store or use

combustible mamrials, gasoline or oilier

flammable vapors or liquids in the vicinity

of this or any other appliance.

All air conditioners contain refrigerants,

which under federal law must be remoxed

plJor to product disposal. If you are getting

rid of an old product with refrigerants, check

with the company handling disposal about

what to do.

HOWTOCONNECTELECTRICITY

Do not, under any circumstances, cut or remove

the third (ground) prong from the power cord. For

personal safe_ this appliance must be properly

grounded.

The power cord of dais appliance is equipped

with a 3-prong (grounding) plug which mates

with a standard 31)iong (grounding) wall

outlet m minimize the possibility of electric

shock hazard from this appliance.

Power coM includes a cnnent intemq)ter

device. A rest and reset button is provided on

the plug case. The device should be rested on a

periodic basis by first pressing tim TESTbntton

and then the RESErbutton. If the TESTbutton

does not trip or if fl_e RESETbutmn will not

stay eng_aged, discontinue use of file air

conditioner and contact a qualified

service mchnician.

Hme the wall outlet and circuit checked by a

qualified electrician to make sure the outlet is

properly grounded.

Where a 9-prong wall outlet is encounmred,

it is your personal responsibility and obligation

to haxe it replaced with a properly grounded

31)iong wall outlet.

The air conditioner should always be

plugged into its own individual elecuical

outlet which has a x_ltag> rating flint matches

the rating plato.

This provides the best perfommnce and also

prexents oxerloading house wiring circuits

which could cause a fire hazard from

oxeflleated wires.

See the Installation Instructions, Electrical

Requirementssection for specific elecuqcal

connection requirements.

www.GEAppliances.com

WARNING!

USEOFEXTENSIONCORDS--115-Vo/tmode/son/y

Because of potential safety hazards under certain..^CAUTION:

conditions, we strongly recommend against the

use of an extension cord.

Howex_. if you must use an extension cord,

it is absolumly necessai T that it be a UiAismd,

14 gauge, 3-wire grounding type appliance

extension cord having a grounding type plug

and outlet and that the elecuJcal rating of tile

cord be 15 ami)eres (minimum) and 195 volts.

DO NOT use an extension cord with any ofthe

230/208volt models.

USEOFADAPTERPLUGS--115-Vo/tmode/son/y

Because of potential safety hazards under certain

conditions, we strongly recommend against the

use of an adapter plug.

Howex_i; if you must/lse all adapmi; where

local codes pemfit, a temporaryconnection may

be made m a i)roi)erly grounded 2-prong wall

outlet 1)yuse of a UL-lismd adaptor available

at most local hardware stoles.

Tile larger slot ill tile adaptor must be aligned

with tile larger slot in the wall outlet to I)rovide

i)roi)er polarity in tile connection of tile

i)ower cord.

'iA]mn disconnecting dm power cord flom tile

adaptel, alwws hold the adaptor ill place with

one hand while I)ulling tile power cord I)lug

with tile other hand. If this is not done, tile

adaptor ground te.rminal is veU likely to 1)reak

with repeamd use.

If tile adapter ground terminal breaks, DO NOT

USEtile air coI/ditioI/er m/ti] a proper grom/d

has been established.

Attachingthe adaptergreundterminalto a waftoutlet

coverscrewdoesnot groundtheapplianceunlessthe

coverscrewis metal,andnot insulated,andthe waft

outlet isgroundedthreughthe housewiring. Youshould

havethecircuitcheckedby a qualifiedelectricianto

makesuretheoutlet is properlygrounded.

READANDFOLLOWTHISSAFETYINFORMATIONCAREFULLY.

SAgETHESEINSTRUCTIONS

Aboutthe controlsontheair conditioner.

Features and appearance may vary.

Lights next to

the touch pads

on the air

conditioner

Energy

control panel saveron

indicate the

selected

settings.

Fan on

Coolon Timeron

I COOL!

Air ConditionerControls

-0

RemoteControl

Controls

ON/OFFPad

TtlYns air conditioner on and off.

TEMP/TIME Increase •/Decrease • Pads

Use to set teinperature when in COOL Inode

or tile time when using tile TIMER feature.

MODE

Use to set tile air conditioner to COOL,

ENERGYSAVERor FANmode.

FAN SPEEDPad

Use to set tile tim speed to LOW(F1),

MED(F2)or HIGH(F3).

TIMER Pad

ON--When tile air conditioner is off,

it can be set to automatically cOiile on in

1 to 24 houI_ at its previous setting. Each

touch of tile Increase •/Decrease • pads

will set tile timer in hom_.

OFF--_A]len tile air conditioner is on,

it can be set to automatically ttlrn off' in

1 to 24 horns. Each touch _ff tile Increase • /

Decrease • pads will set tile timer in hom_.

Tocancel _e timer, press tile TIMERpad

tmtil tile display time disappears.

Remote ControlSignal Receiver

Display

Shows tile set temperature or time remaining

on _I//eY.

Power Outage Recovery Feature

In tile case of a power outage or interruption, tile

refit will automatically re-start in tile settings last

used after tile power is restored. Tile TlMERleatm'e

xfill reset to tile off *inal setting You max need to set

a new time if desired.

Remote Control

To enstli'e proper opei'ation, aill/ tile i'elllote

control at tile signal receiver on tile air

conditionei:

Tile remote control signal has a range of

up to 21 feet.

Make sure nothing is between tile air conditioner

and tile remote control that could block tile

signal.

Make sure batmries are fresh and installed

correctly as indicated on the remote control

wvvw.GEAppliances.com

COOLMode

Usethe COOLmode with HIGH(F3),MED(F2)or

LOW(FI) tim for cooling. Use tile Increase • /

Decrease • pads to set tile desired temperature

between 60°F and 86°F in l °F increments,

An electronic them_ostat is used to maintain tile

room temperature, The (_)mpressor will cycle on and

off to keep the room at the set level of comfi)rt. Set

the them/ostat at a lower number and the indoor air

will become cooler. Set the them_ostat at a higher

number and tile indoor air will become wam/e_;

NOTE"ff theair conditioneris off and isthentumed on

whileset to COOL,it will take approximately3 minutes

for the compressorto startand coolingtobegin.

CoolingDescriptions

ForNormalCooling--Select tile COOLmode and

HIGH(F3)or MED(F2)fimwith a middle set

temperature,

ForMaximumCooling--Select the COOLmode

and HIGH (F3)tim with a lower set temperatm'e.

ForQuieter& NighttimeCooling--Select the

COOL mode and LOW (FI)tim with a middle set

temperature,

NOTE:If youswitch from a COOLsettingto OFForto

a fan setting,wait at least3 minutesbeforeswitching

back to a COOLsetting.

Energy Saver

The energy saver switch controls the Lm.

O/_-The tim and compressor cycle on and off

together; This results in wider \m_iafions of room

temperature and hmnidity. Nommlly used when

the room is m_occupie(l. NOTE:Thefanwill continue

to run fora shorttime after thecompressorcycles off.

OFF The tim runs all the time, while the

compressor cycles on and ofl_

This switch Inust be set at OFFin order to rise

tile tim settings (on tile mode control),

FAN Mode

Use the FAN at HIGH (F3), MED (F2) or LOW(F1) to Since tim only settings do not provide cooling,

provide air circulation and filtering without cooling, a temperature setting will not be displayed.

Vent Control

Tile vent control is located above tile control

panels.

When set at CLOSE, only the air inside the room

will be circulated and conditioned, _'hen set at

OPEN,solne inside air is exhausted outside.

Toopenthe vent,pull thelever toward you.

Toclose it, push it hT.

Air Direction--Side-to-Side

The side-to-side air direction is a(!i usted 1)y moving

tile lever to tile left or fight.

Air Direction--Up and Down

Fingertip pressm'e on tile horizontal louve_

a(!justs tile air direction up or down.

Careand cleaning oftheair conditioner.

Grille and Case

Turn the......air conditioner off and remo'_e the I)lug, To clean, use water and a mild detergent. Do not

from the wall outlet betore cleaning, use bleach or abrasixes.

Outdoor Coils

The coils on the outdoor side ot the air conditioner

should be checked regtflarly. If they are clogged

with dirt or soot, they may be protessionally

cleaned.

Air Filter

The air filter behind the h'ont grille should be

checked and cleaned at least exe_'_ 30 days or

II/OI'e oJ[[en i[ necess_li'v.

Toremove:

[ _ 0/1[

[_] Open the inlet grille dowmvard b) )ullin,,

the top corne_ of the inlet grille.

] Pull up slightly on the filter to release it and

pull it out.

Clean the filter with wam_, soapy water: Rinse and

let the filmr dry before replacing it.

A CAUTION:DONOroperate bea,

conditionerwithouta filterbecausedirtandlintwillclogit

and reduce performance.

Installation

Instructions

Air Conditioner

I I'_'1 Questions? Call 800.GE.CARES (800.432.2737) or Visit our Website at: www.GEAppliances.com I

BEFORE YOU BEGIN

Read these instructions completely

and carefully.

• IMPORTANT - Savethese

instructions for local inspector's use.

• IMPORTANT - Observeall

governing codes and ordinances.

• Note to Installer - Be sure to leave these

instructions with the Consumer.

• Note to Consumer - Keep these

instructions for future reference.

• Skill level - Installation of this appliance

requires basic mechanical skills,

• Completion time - Approximately 1 hour

• We recommend that two people install

this product.

• Proper installation is the responsibility

of the installer.

• Product failure due to improper installation

is not covered under the Warranty.

(_ ELECTRICAL REQUIREMENTS

Some models require a 115/120-volt a.c.,

60 Hz grounded outlet protected with a

15-amp time delay fuse or circuit breaker.

The 3-prong grounding plug minimizes the

possibility of electric shock hazard. If the wall

outlet you plan to use is only a 2-prong outlet,

it is your responsibility to have it replaced with

a properly grounded 3-prong wall outlet.

Some models require 230/208-volt a.c.,

protected with a time delay fuse or circuit

breaker. These models should be installed

on their own single branch circuit for

best performance and to prevent

overloading house or apartment wiring

circuits, which could cause a possible

fire hazard from overheating wires.

CAUTION:

Do not, under any circumstances, cut or

remove the third (ground) prong from the

power cord.

Do not change the plug on the power cord

of this air conditioner.

Aluminum house wiring may present special

problems--consult a qualified electrician.

TOOLS YOU WILL NEED

Phillips head screwdriver

Flat-blade screwdriver

Pencil Ruler or tape measure

Level Scissors or knife

Power cord includes a current interrupter

device. A test and reset button is provided on

the plug case. The device should be tested on a

periodic basis by first pressing the TEST button

and then the RESET button, If the TEST button

does not trip or if the RESET button will not stay

engaged, discontinue use of the air conditioner

and contact a qualified service technician.

Installation Instructions

PARTS INCLUDED

(Appearance may vary)

Window

;ash seal

Left Top. ___

accordion mount,ng Foam top /___':.._-

panel rail\ window gasket __. "_.

To0_ount,n0\ _ __"

--, railsealstri _ _ _

Frame _d_. (2) "" i ac!!_dhei/n

"_ S b k 2 _llllllll

Window locking " IltlJl upport rac et( )

bracket [Jr,_

Type A (14)

Type B (7)

Type C (5) Type D (2) Carriage Bolt (2)

Lock Nut (4)

Installation Instructions

[] WINDOW REQUIREMENTS

• These instructions are for a standard

double-hung window. You will need to

modify them for other types of windows.

• The air conditioner can be installed

without the accordion panels if needed

to fit in a narrow window. See the

window opening dimensions.

• All supporting parts must be secured

to firm wood, masonry or metal.

• The electrical outlet must be within

reach of the power cord.

I /P" I

B===8

19"rnin. 1

29"to41"

(Withaccordionpanels)

'i- i

26W' rain.

(Withoutaccordionpanels)

[]

STORM WINDOW REQUIREMENTS

A storm window frame will not allow the

air conditioner to tilt toward the outside,

and will keep it from draining properly.

To adjust for this, attach a piece of wood

to the stool.

WOOD PIECES-

WIDTH: 2"

LENGTH: Long enough to fit inside the

window frame.

THICKNESS: To determine the thickness,

place a piece of wood on the stool to

make it 1/2" higher than the top of the

storm window frame.

Attach securely with nails or screws

provided by the installer.

1/2" hi

than frame Stool

Storm

window

fra me

Installation Instructions

[] REMOVE THE AIR CONDITIONER

FROM THE CASE

IAq Remove the 2 shipping screws from the

back of the case.

[] Remove the 2 screws on each side of the

case. Keep these for later use.

[] Slide the air conditioner from the case by

gripping the base pan handle and pulling

forward while bracing the case.

[] PREPARE THE WINDOW AND

THE CASE

[] Cut the window sash seal to the proper

length. Peel off the backing and attach the

seal to the underside of the window sash.

[] PREPARE THE WINDOW AND

THE CASE (CONT.)

[] Carefully insert the plastic frame guides

into the bottom of the case on each side.

Bottomofcase /_

_ Frameguide

[] Remove the backing from the top mounting

rail seal strip and attach it to the bottom of

the top mounting rail.

[]

Install the top mounting rail with 3 type A

screws on the inside of the case. Insert the

frames for the accordion panels into the top

mounting rail and the frame guides. Attach

the accordion panels to the side of the case

using 5 type A screws on each side.

Topmountingrail

Frameguides

Installation Instructions

[] PREPARE THE WINDOW

I_] Loosely attach the sill brackets to the

"L_2J

support brackets using the 2 carriage bolts

and 2 lock nuts.

[]

Support bracket

Carriage I

bolt

_ _..,,.. _,. _jock nut

Sillbracket/

Open the window and mark the centerline

of the window stool. Measure and mark 11"

to the left and right of the centerline.

Centerline

[] INSTALL THE CASE IN THE

WINDOW

[] Align the inside edge of the sill brackets

with the 11" marks from the centerline and

attach them to the window sill using 2 type

B screws on each side.

[]

Carefully place the case on the window

stool aligning the center front on the

bottom with the centerline marked on the

window stool. Close the window making

sure the window sash is behind the top

mounting rail.

Using the larger diameter hole in the case,

attach the brackets to the case using two

type D screws and 2 lock nuts on each side.

[] INSTALL THE CASE IN THE

WINDOW (CONT.)

[] Adjust the carriage bolts and the lock nuts

in each support so that the case is installed

with a slight tilt to the outside. Use a level;

about 1/3 bubble will be the correct case

slant to the outside. Tighten the bolts.

CAUTION: DO NOT drill a hole in the base pan.

The unit is designed to operate with

approximately 1/2" of water in the base pan.

[] Secure the case to the window stool by

using 3 type B screws.

[] Pull the accordion panels to each window

sash track. Attach them on each side to the

window sash and the window stool using

4 type C screws.

Installation Instructions

[] INSTALL THE WINDOW LOCKING

BRACKET AND THE FOAM TOP

WINDOW GASKET

[] Attach a support bracket with a Type C

screw.

[] Cut the foam top window gasket to the

window width.

[] Stuff the foam between the glass and the

window to prevent air and insects from

getting into the room.

[] INSTALL THE AIR CONDITIONER

IN THE CASE

I_q Slide the air conditioner into the case.

Inl

Reinstall the 2 screws removed earlier on

each side of the case.

Screw Screw

[] INSTALL THE AIR CONDITIONER

IN THE CASE (CONT.)

[] Before installing the front grille, pull out the

vent control lever located above the unit

control knobs, as shown.

[] Attach the front grille to the case by inserting

the tabs on the grille into the slots on the

front of the case. Push the grille in until it

snaps into place.

[]

, ._=_

Guidethe lever carefully

flTroughthe grille as you

push it in.

Lower the inlet grille and secure the front

frame with a type A screw through the

front grille. Raise the inlet grille back

into place.

Troubleshootingtips. www.GEAppliances.com

Troubleshooting -tips.

Save time and money! Review the chart below first

and you may not need to call for service.

Possible Causes What To Do

Air conditioner The air conditioner • Make sure tile air conditioner phtg is pushed completely

does notstart is unplugged, into the outlet.

The fuse is blown/circuit • Check tile house fllse/circuit breaker box and replace

breaker is tripped, the fl/se or reset the breaker:

Power failure. •/f power tifilure occtu_, turn the air conditioner OFF.

_lwn power is restored, wait 3 minutes to restart the

air condifi(mer t() prevent tril)ping ()t the c()mpress()r

()verload.

The current interrupter • Press the RESErbutton h)cated on the l)ower cord l)lug.

device is tripped. •/f the RESETbutton will not stay en _a,,ed discontinue

use ()t the air c(mditioner and contact a qualified service

tech nicia n.

Air conditioner does not Airflow is restricted. • Make sure there are no curtains, blinds or flmfiture

cool as itshould blocking the fl'ont of the air condifione_:

The temperature control may •/n COOLm()de, press the Decrease Vl)ad.

not be set correctly.

The air f'dter is dirty. • Clean the filter at least eve U 30 days.

See the Operating Instructions section.

The room may have been hot. • _4]/ell the air conditioner is fil_t turned on, you need to

allow time fin" the room to cool down.

Cold air is escaping. • (;he('k fi)r oI)en flU'hate floor registe_ and cold air

I'ett/Yns.

• Set the air conditioner's vent to the closed position.

Cooling coils have iced up. • See "Air conditioner freezing up"beh)w.

Air conditioner lee blocks the air flow and • Set the c(mtr(>ls at HIGH (F3)FAN or HIGH (F3) COOLand

freezing up stops the air conditioner set the them_(>stat to a higher temperature.

from cooling the room.

The remote control The batteries are haserted • Check the position of the batteries. They shotfld be

is not working incorrectly, inserted in the ol)posite (+) and (-) direction.

The batteries may be dead. • Rel)lace the batteries.

Waterdrips outside Excessively hot and • This is nom, al.

hmnid weather.

Water drips indoors The air conditioner is not • F()r l)r()per water disl)()sal, make stu'e the air c(mdifi(mer

tilted to the outside, slants slightly t]'om the case fl'(mt t(>the re:u:

Watercollectsin

basepan

Moisture is removed from

indoor air and drains into

rear of a cabinet where a fan

blows it against the outdoor

condenser coil.

• This is nomml for a short period in areas Mth little

lmmidity; nom_al fin" a longer period in \'e_' humid areas.

TIMERfeaturenot

working properly

A power outage or interruption

occurred,

• In the case of a power outage or interruption, the unit

77MERteature will reset to the original setting. Ybu may

need to set a new time if desired.

Troubleshootingtips.

Normal Operating Sounds

You nlav hear a i_inging noise caused bv water

being picked up and thrown against the

condenser Oil rainy days or when the huniidiP,'

is high, This design _eatui'e helps relnove

inoisture and iniprove efficiency.

You nlav hear the thei_nostat click when the

COIlll)I'essof cycles on _lIl(1 oJZ{ '.

_,V_ter will collect in the base pan dui'ing high

huiniditv or on rainy days. The water nlav

ovei-flow and drip ti'oin the outdoor side/)t

the unit.

; The J[ilIl Ill,IV I'{lIl even when the COIlll)I'essoI"

does not,

GE Service Protection Plus 'M

GE, a name recognized worldwide %r quality and dependability, of{ers you

Service Protection Plus'_--comprehensive protection on all your appliances--

No Matter What Brand!

Benefits Include:

• Backed by GE

• All brmads covered

• Unfimited service calls

• All parts mid labor costs included

• No out-of-pocket expenses

• No hidden deductibles

• One 800 nmnber to call

We71 CoverAnyAppliance.

Anywhere. Anytime.*

You will be completely satisfied with our service protection or )ou ma) request }our inone) back

on the remaining value of your contract. No questions asked. It's that simple.

Protect yore" refrigerator, dishwasher, washer and dryer, range, TV, VCR and much more--any brand!

Plus there's no extra charge tor emergency service and low monthly financing is available. Even icemaker

coverage and tood spoilage protection is offered. You can rest eas> knowing that all vom" valuable

household products are protected against expensive repairs.

Place vot,r confidence in (;E and call us in the U.S. toll-free at _tlII.DZD.ZZZ_

for uloi'e ii_torlnation,

*All brands cmered, up to 20 }ears old. in the contin_ real [.S.

._(_t/I here

Please place in envelope and mail to:

General Electric Company

Warranty Registration Department

P.O. Box 32150

Louisville, KY 40232-2150

Consumer Product Ownership Registration

Deal Customer:

Thank you for purchasing our product and thank you for placing your confidence in us.

_:e are proud to haxe you as a customer!

Follow these three steps to protect your new appliance investment:

Complete mid mail

your Consumer

Product Ownership

Registration today:

Ilavc the pcm'c ot

nlind of knowing we

Call COlltaCt yOl/ ill

the unlikelx event of a

saf}:tv modification.

After mailing the

registration below,

store this document

in a sat;:, place. It

contains intormation

vou will need should

you reqtfire service.

Our service numl)er is

800.(;E.CARES

(800.432.2737).

Read vour Owner's

Manual careftflly.

It will help you

operate yollr llew

appliance properl>

Model Number Serial Number

Important: If you did not get a registration card with your

product, detach and return the form below to

ensure that your product is registered, or register

online at GEAppliances.com.

._Cut here

Consumer Product Ownership Registration

Model Number Serial Number

M*: Ms. Mrs. Miss

FirstI I L_stl

Nam( I I I I I I I I I Nam( I I I I I I I I I I I I

Sir( et I

Address I I I I I I I I I I I I I I I I I I I I I I I I

AI,,.#I' ' ' ' I ' ' I E-mailAddress*

Daw 1'1_c( d

Pholle

Month I I

GEAppliances

BE Consomor & htdustrial

Louisville, Kentucky

wwv_aEAppliances, com

* Please proxide your eqnail address to receive, xia e-mail, discomlts, special ott;:rs and other important

comnmnications ti-om GE Appliances ((;EA).

[ Check here if you do not want to receive communications from (;EA's careftllly selected partner',.

FAIIMRE TO COMPIA{TE AN[) RETI JRN TIIIS CARD DOES NOT DIMINIStt YO[ R

_,i \RI_ \N'IY RIGI fFS.

For infkn-mation about GEA's privacy and data usage policy, go to x_a_v.(;EAppliances.com and click

on 'Privacy Policy" or call 800.626.2224.

Air ConditionerWarranty.

Aft warranty service provided by our Factory Service Centers,

or an authorized Customer Care®technician. Toschedule service,

on-line, 24 hours a day, visit us at GEAppliances.com, or carl

800.GE.CARES (800.432.2737).

Staple your receipt here.

Proofof the original purchase

date is needed to obtain service

under the warrantg

Fromthedateof the

origina!purchase

Fromthedateof the

originalpurchase

We Will Replace:

Anypartof the air conditioner which thils due to a defect in materials or workmanship,

During this full one-year warranty, we will also provide, free of charge, all lab(n" and in-home

serxice to replace the (lefecti',e part,

Any part ofthe sealed refrigerating system (the comi)ressot; condenset; evaporator and

all connecting tubing) which fifils due to a defect in materials or workmanship, During this

four-year additional warranty, we will also provide, free of charge, all labor and in-home service

to replace the defecti\'e part,

Service trips to your home to teach you how to

use the product.

hnproper h_staJlation, delivery or maintenance. If you

have ml installation problem, or if the air conditioner

is of improper cooling capacity for the intended use,

contact your dealer or installer. You are responsible

for providing adeqwate electrical cmmecth_g facilities.

Failure of the product restflth_g from modifications to

the product or due to mlreasonable use including failure

to provide reasonable mad necessary maJntenmace.

In commerciaJ locations labor necessary to move the

unit to a location where it is accessible for service

by an individual technician.

Replacement of house fuses or resetting of circuit

breakers.

Failure due to corrosion on models not corrosion-

protected.

Dmnage to the product caused by hnproper power supply

voltage, accident, fire, floods or acts of God.

Incidental or consequentiaJ dmnage caused by possible

defects with this air conditioner.

Dmnage caused after delivery.

This warranty is extended to the original purchaser and any succeeding owner for products purchased for home

use within the USA. In Alaska, the warranty excludes the cost of shipping or service calls to your home.

Some states do not allow the exclusion or limitation of incidental or consequential damages. This warranty gives

you specific legal rights, and you may also have other rights which vary from state to state. Toknow what your

legal rights are, consult your local or state consumer affairs office or your state's Attorney General.

Warrantor: General Electric Company. Louisville, KY 40225

ConsumerSupport.

q l gEAppliancesWebsite www.GEAppliances.com

Haxe a question or need assistance with your appliance? Try the (;E Appliances _4'ebsite 24 hotn_ a day

' any day of the xear'. For greater comenience and faster service, you can now download Owner's Manuals,

O " S i.order parts, catalogs, or exert schedule set\ice on-line. You can also "_&skOur Team f Expert.

V(//II" questions, and so IIltlch iiloi'e...

ScheduleService

www.GEAppliances.com

Expert (;E repair sels,ice is onl) one step away fl'om your dooi; Get on-line and schedule v,'mr service at

your, conxenience 24 h{/ui_ am {lm of the xear! Or call 800.GE.CARES (800.432.2737) dining n{mnal

business houi_.

RealLifeDesignStudio www.GEAppliances.com

GE supports the Univei_al Design concel)t--products, services and environments that can be used by

people of all ages, sizes and capabilities. We recognize the need to design fin" a wide range of physical and

mental abilities and impaimmnts. For details of GE's Univelsal Design applications, including kitchen

design ideas fin" people with disabilities, check out our _,Vebsim today. For the hearing impaired, please call

800.TDD.GEAC (800.833.4322).

Extended Warranties www.GEAppliances.com

Purchase a GE extended warran_ and learn about special discounts that are axailable while _our warrant'

is still in effect. Yell C_lllpurchase it on-line an) time, or call 800.626.2224 during nomml business hom_.

(;E (_onsulner Home Serxices will still be there alter your warrant} expires.

PartsandAccessories www.GEAppliances.com

Individuals qualified to service their own appliances can have parts or accessories sent directly to their

homes (VISA, MasterCard and Discover cards are accepted). Order on-line today, 24 hom_ evela' day

or by phone at 800.626.2002 during nomml business hom_.

Instructions contained in this manual cover procedures tobe performed byany user. Otherservicing generally

should be referred to qualified service personnel. Cautionmust be exercised, since improper servicing may cause

unsafe operation.

ContactUs www.GEAppliances.com

If you are not satisfied with the service you receive from GE, contact us on our _.Vebsite with all the details

including your phone ntlIllbeI; oF write to: General Managei; Customer Relations

GE Appliances, Appliance Park

I,ouisville, KY 40225

RegisterYourAppliance www.GEAppliances.com

enhanced communication and prompt service under the terms of,,our warranty should the need alise.

You may also mail in the pre-printed registration card included in the packing material.

] o° Printed inKorea

Page is loading ...

GE AGM24DHM1 Owner's manual

Brand: GE

Model: AGM24DHM1

Category: Mobile air conditioners

Type: Owner's manual

This manual is also suitable for

Download PDF

report

in other languages

español: GE AGM24DHM1 El manual del propietario

GE AGM24DHM1 Owner's manual

This manual is also suitable for

GE AGM24DHM1 Owner's manual

in other languages

Related papers

Other documents