Chicco Fun Travel Safari Car Toy Owner's manual

Page is loading ...

8

9

Instruction manual SAFARI CAR TOY

GB

USA

Age: 12 Months +

• Please read these instructions carefully before using the toy and keep for future reference.

• The toy is battery operated as follows: 3 x 1.5 Volt AA batteries for the panel (included), 2 x 1.5

Volt AAA batteries for the infrared remote control (included). The batteries supplied with this

product, at the point of sale, are intended for demonstration purposes only; please replace them

immediately after completing your purchase.

WARNINGS

For your child's safety: WARNING!

• Before using the product remove and dispose of any plastic bags and any other packaging (e.g.

fasteners and xing ties etc) and keep them out of reach of children. Suffocation hazard.

• Check the toy regularly for signs of wear and damage and to ensure that it is assembled correctly.

Should any part be damaged, do not use the toy and keep it out of reach of children.

• This toy must only be used under adult supervision.

• Always use the toy with the child car seat facing forwards.

• This car panel must only be assembled and tted by an adult.

• The panel can only be installed on the back of front car seats which have a head rest.

• Make sure the panel is tted correctly and rmly attached to the head rest. Check it regularly to

ensure it has not come loose.

• Never leave the panel on a vehicle seat without fastening it securely in place; it could hurt or

injure other passengers in the car.

• Remember never to turn your head to switch the toy on, or pick up the infrared remote control

while you are driving the car.

• When the rear seat is empty, the infrared remote control can be fastened to the panel using the

relative slot. When the child is sitting in the car seat, fasten the infrared remote control to the

child car seat harness only.

• This product must not be modied in any way; never fasten other ties or straps to it.

INSTALLING THE PANEL IN THE CAR

Open the buckles (A. Diag. 1) found on the back of the panel and fasten them to the supports on

the head rest. Pull the straps (B, Diag. 2) to fasten the panel rmly to the seat.

FASTENING THE INFRARED REMOTE CONTROL TO THE CAR SEAT

Fasten the infrared remote control (C, Diag. 3) to the child car seat safety harness strap (D, Diag.

3) using the velcro fastener strap. This aims to prevent the toy from falling onto the oor when

travelling by car.

HOW TO USE THE TOY

Switching it ON and Off

• To switch the toy panel ON, move the switch E (Diag. 4) from the 0 position to the I position

(Relax) or II (Fun) position according to the game mode desired.

• To adjust the volume level, move the switch F (Diag. 4) from the <)) (low) position to the <)))

(high) position.

• In order to avoid using up the batteries for no reason, it is recommended to switch off the toy by

moving the switch E (Diag. 4) to the 0 position.

• Insert the batteries in the walkie-talkie style infrared remote control before using it; it only works

when the toy panel is set to Fun mode.

• To start the game functions, point the sensor on the infrared remote control at the panel (Diag.

4.1).

Play modes

1. RELAX: to enable this play mode, move the switch E (Diag. 4) to the I position.

The low lights and soft music gently soothe your baby. The infrared remote control does not work

when the toy is operating in this play mode. The toy will switch off automatically after 15 minutes.

To restart it, switch it off by moving the switch to the 0 position. Then switch it back on and set

the desired play mode.

2. FUN: to enable this play mode, move the switch E (Diag. 4) to the II position. A jingle will con-

rm the play mode choice. When set to Fun mode, every time the child presses one of the buttons

on the infrared remote control (Diag. 5) the relative sound effect will play. If the same button is

pressed a number of times, a tune will play. In both cases, the images linked to the buttons will be

displayed on the panel so your baby will learn to recognise them. When set to FUN mode, if the

toy is not used for about 20 minutes, it will play a sound effect and switch off automatically. To

restart it, switch it off by moving the switch to the 0 position. Then switch it back on and set the

play mode of your choice.

HOW TO FIT AND REMOVE THE REPLACEABLE BATTERIES

• To replace the panel batteries: loosen the screw on the battery compartment cover (G, Diag. 6)

on the back with a screwdriver and remove the cover; then remove the at batteries and t new

ones, ensuring that the battery polarity is correct (as shown on the product), close the battery

compartment cover, and tighten the screw rmly.

• To replace spent batteries inside the infrared remote control: open the velcro fastener on the

back, loosen the screw on the battery compartment cover (H, Diag. 7) on the back with a screw-

driver and remove the cover; then remove the at batteries and t new ones, ensuring that the

battery polarity is correct (as shown on the product), close the battery compartment cover, and

tighten the screw rmly. Close the velcro fastener rmly when you have nished changing the

batteries.

WARNING

• Batteries must only be tted by an adult.

• Always keep batteries and tools out of the reach of children.

• Always remove spent batteries from the toy to avoid the danger of leakage from the battery

damaging the product.

• Always remove the batteries if the product will not be used for a long period of time

8

9

Age: 12 Months +

• Please read these instructions carefully before using the toy and keep for future reference.

• The toy is battery operated as follows: 3 x 1.5 Volt AA batteries for the panel (included), 2 x 1.5

Volt AAA batteries for the infrared remote control (included). The batteries supplied with this

product, at the point of sale, are intended for demonstration purposes only; please replace them

immediately after completing your purchase.

WARNINGS

For your child's safety: WARNING!

• Before using the product remove and dispose of any plastic bags and any other packaging (e.g.

fasteners and xing ties etc) and keep them out of reach of children. Suffocation hazard.

• Check the toy regularly for signs of wear and damage and to ensure that it is assembled correctly.

Should any part be damaged, do not use the toy and keep it out of reach of children.

• This toy must only be used under adult supervision.

• Always use the toy with the child car seat facing forwards.

• This car panel must only be assembled and tted by an adult.

• The panel can only be installed on the back of front car seats which have a head rest.

• Make sure the panel is tted correctly and rmly attached to the head rest. Check it regularly to

ensure it has not come loose.

• Never leave the panel on a vehicle seat without fastening it securely in place; it could hurt or

injure other passengers in the car.

• Remember never to turn your head to switch the toy on, or pick up the infrared remote control

while you are driving the car.

• When the rear seat is empty, the infrared remote control can be fastened to the panel using the

relative slot. When the child is sitting in the car seat, fasten the infrared remote control to the

child car seat harness only.

• This product must not be modied in any way; never fasten other ties or straps to it.

INSTALLING THE PANEL IN THE CAR

Open the buckles (A. Diag. 1) found on the back of the panel and fasten them to the supports on

the head rest. Pull the straps (B, Diag. 2) to fasten the panel rmly to the seat.

FASTENING THE INFRARED REMOTE CONTROL TO THE CAR SEAT

Fasten the infrared remote control (C, Diag. 3) to the child car seat safety harness strap (D, Diag.

3) using the velcro fastener strap. This aims to prevent the toy from falling onto the oor when

travelling by car.

HOW TO USE THE TOY

Switching it ON and Off

• To switch the toy panel ON, move the switch E (Diag. 4) from the 0 position to the I position

(Relax) or II (Fun) position according to the game mode desired.

• To adjust the volume level, move the switch F (Diag. 4) from the <)) (low) position to the <)))

(high) position.

• In order to avoid using up the batteries for no reason, it is recommended to switch off the toy by

moving the switch E (Diag. 4) to the 0 position.

• Insert the batteries in the walkie-talkie style infrared remote control before using it; it only works

when the toy panel is set to Fun mode.

• To start the game functions, point the sensor on the infrared remote control at the panel (Diag.

4.1).

Play modes

1. RELAX: to enable this play mode, move the switch E (Diag. 4) to the I position.

The low lights and soft music gently soothe your baby. The infrared remote control does not work

when the toy is operating in this play mode. The toy will switch off automatically after 15 minutes.

To restart it, switch it off by moving the switch to the 0 position. Then switch it back on and set

the desired play mode.

2. FUN: to enable this play mode, move the switch E (Diag. 4) to the II position. A jingle will con-

rm the play mode choice. When set to Fun mode, every time the child presses one of the buttons

on the infrared remote control (Diag. 5) the relative sound effect will play. If the same button is

pressed a number of times, a tune will play. In both cases, the images linked to the buttons will be

displayed on the panel so your baby will learn to recognise them. When set to FUN mode, if the

toy is not used for about 20 minutes, it will play a sound effect and switch off automatically. To

restart it, switch it off by moving the switch to the 0 position. Then switch it back on and set the

play mode of your choice.

HOW TO FIT AND REMOVE THE REPLACEABLE BATTERIES

• To replace the panel batteries: loosen the screw on the battery compartment cover (G, Diag. 6)

on the back with a screwdriver and remove the cover; then remove the at batteries and t new

ones, ensuring that the battery polarity is correct (as shown on the product), close the battery

compartment cover, and tighten the screw rmly.

• To replace spent batteries inside the infrared remote control: open the velcro fastener on the

back, loosen the screw on the battery compartment cover (H, Diag. 7) on the back with a screw-

driver and remove the cover; then remove the at batteries and t new ones, ensuring that the

battery polarity is correct (as shown on the product), close the battery compartment cover, and

tighten the screw rmly. Close the velcro fastener rmly when you have nished changing the

batteries.

WARNING

• Batteries must only be tted by an adult.

• Always keep batteries and tools out of the reach of children.

• Always remove spent batteries from the toy to avoid the danger of leakage from the battery

damaging the product.

• Always remove the batteries if the product will not be used for a long period of time

10

11

• Only use alkaline batteries of the same type or equivalent to the type recommended for the

correct function of this product.

• Never mix new and old batteries.

• If the batteries happen to leak liquid, replace them immediately, making sure you clean the

compartment beforehand; wash your hands thoroughly if you come into contact with any such

liquid.

• Remove the batteries from the toy before disposing of the product.

• Do not burn or dispose of old batteries into the environment. Dispose of them at an appropriate

differentiated collection point.

• Never mix alkaline, standard (zinc-carbon) or rechargeable batteries.

• This product is not designed for use with lithium batteries. WARNING: Improper use could be

hazardous

• Do not short-circuit the battery terminals.

• Do not attempt to recharge non-rechargeable batteries: they might explode.

• The use of rechargeable batteries is not recommended as the toy may not work properly.

• If using rechargeable batteries, remove them from the toy before recharging them. Batteries

must always be recharged under adult supervision.

This product complies to EU directive 2002/96/EC.

The crossed bin symbol on the appliance indicates that the product, at the end of its

life, must be disposed of separately from domestic waste, either by taking it to a sepa-

rate waste disposal site for electric and electronic appliances or by returning it to your

dealer when you buy another similar appliance. The user is responsible for taking the appliance to

a special waste disposal site at the end of its life. If the disused appliance is collected correctly as

separate waste, it can be recycled, treated and disposed of ecologically; this avoids a negative im-

pact on both the environment and health, and contributes towards the recycling of the product’s

materials. For further information regarding the waste disposal services available, contact your

local waste disposal agency or the shop where you bought the appliance.

This product complies to EU directive 2002/95/EC.

This product complies with EC directive 2006/66/EC.

The crossed bin symbol on the batteries or product pack indicates that, at the end

of their life, they must not be disposed of as urban refuse. They must be disposed of

separately from domestic waste, either by taking them to a separate waste disposal site for bat-

teries or by returning them to your dealer when you buy similar rechargeable or non-rechargeable

batteries.

The chemical symbols Hg, Cd, Pb, printed under the crossed bin symbol, indicate the type of

substance contained in the batteries: Hg=Mercury, Cd=Cadmium, Pb=Led.

The user is responsible for taking the batteries to a special waste disposal site at the end of their

life, so that they can be treated and recycled. If the spent batteries are collected correctly as

separate waste, they can be recycled, treated and disposed of ecologically; this avoids a negative

impact on both the environment and human health, and contributes towards the recycling of the

batteries’ substances. Non-compliance with the norms on battery disposal damages the environ-

ment and human health. For further information regarding the waste disposal services available,

contact your local waste disposal agency or the shop where you bought the batteries.

CLEANING, CARE & MAINTENANCE OF THE TOY

• The toy should only be cleaned using a soft, dry or moistened fabric or microbre cloth to avoid

damage to its electric circuit. Do not clean the toy with detergents or solvents.

• Protect the toy against heat, dust, sand, humidity and water.

Fabric used for the toy panel and infrared remote control:

Outer cover: 100% Polyester

Padding: 100 % Polyester

Do not wash in water

Do not bleach

Do not tumble dry

Do not iron

Do not dry clean

Made in China.