American Standard Moments T506.740 User manual
- Category
- Sanitary ware
- Type
- User manual
American Standard Moments T506.740 is a central thermostat with volume control. It has been certified to comply with ANSI A112.18.1M and ASSE 1016 standards. The device comes with a trim kit and has roughing-in dimensions of 160mm x 220mm x 100mm. It can be installed with either 1/2" NPT or 3/4" NPT inlets, and the fitting must be installed with the volume control on top. The device includes a plaster guard, caps, an escutcheon holder, an escutcheon, a fixation plate, handles, and a handle adapter.
American Standard Moments T506.740 is a central thermostat with volume control. It has been certified to comply with ANSI A112.18.1M and ASSE 1016 standards. The device comes with a trim kit and has roughing-in dimensions of 160mm x 220mm x 100mm. It can be installed with either 1/2" NPT or 3/4" NPT inlets, and the fitting must be installed with the volume control on top. The device includes a plaster guard, caps, an escutcheon holder, an escutcheon, a fixation plate, handles, and a handle adapter.
MOMENTS T506.740
Installation
Instructions
M968026
Thank you for selecting American-Standard...the
benchmark of fine quality for over 100 years.
To ensure that your installation proceeds smoothly--please
read these instructions carefully before you begin.
Certified to comply with ANSI A112.18.1M
ASSE 1016
ROUGHING-IN DIMENSIONS
Recommended Tools
Flat Blade Screwdriver
Phillips Screwdriver
Remove as much surface dirt and film using clear
water and soft cotton cloth (as described above).
Use any of the following to remove tough surface
film and build-up:
Mild liquid detergents
Clear ammonia free liquid glass cleaners
Non-acidic, non-abrasive gentle liquid or fully
dissolved powder cleansers mixed according to
manufacturers directions.
Non-abrasive liquid polishers
Once clean, rinse faucet again with clear water to
thoroughly remove cleaner or polish and blot dry with
a soft cotton cloth.
To keep your new faucet looking new, please follow
these simple care instructions:
DO: Simply rinse the faucet clean with clear water.
Dry the faucet with a soft cotton cloth.
DO NOT:
Do not use any abrasive cleaners, cloths, or
paper towels.
Do not use any cleaning agents containing
acids, polish abrasives, or harsh cleaners or
soaps.
Regular and routine cleaning will reduce the need for
heavy cleaning and polishing. If heavy cleaning is
required, the following procedures are recommended:
CARE INSTRUCTIONS:
Failure to follow these care instructions may
damage the Faucet's finish.
CENTRAL THERMOSTAT
WITH VOLUME CONTROL
TRIM KIT
186mm
(7-3/8)
100mm
(3-7/8)
220mm
(8-5/8)
48mm to 68mm
(2 to 2-5/8)
170mm
(6-3/4)
NOTE: FITTING
MUST BE INSTALLED
WITH VOLUME CONTROL
ON TOP.
R520
1/2" NPT INLETS
or
R540
3/4" NPT INLETS
25mm
(1)
FINISHED
WALL
160mm
(6-1/4)
M968026
12
INSTALL HANDLES
Should the hot and cold water supply pipes have been transposed making
adjustment impossible, proceed as follows:
TRANSPOSED SUPPLY PIPING
OR BACK TO BACK INSTALLATION
3
Remove check stops and re-install them transposed.
Shut off water supply.
Remove handle and rim. (Reverse steps 1 and 2).
CHECK STOP
(RED TO BLUE)
Turn the water supply back on and perform the temperature adjustment in step 4.
Assemble HANDLES and TRIM.
CHECK STOP
(BLUE TO RED)
Important note: RED CHECK STOP is now on the right of the mixer body and the BLUE
CHECK STOP is now on the left.
8
8
1
9
2
7
4
4a
3
Thread HANDLE SCREW (1) into VALVE STEM (2) and tighten
to secure KNOB MOUNT (3).
Align HANDLE (4) and push onto KNOB MOUNT (3).
Tighten SET SCREW (5) in handle with HEX WRENCH (6) SUPPLIED.
Install HANDLE ADAPTER (7) onto TEMPERATURE CONTROL KNOB (8)
and tighten with SCREW (9).
Align HANDLE (4a) and push onto TEMPERATURE CONTROL KNOB (8).
Tighten SET SCREW (5a) in handle with HEX WRENCH (6) SUPPLIED.
5a
6
5
TOP
1
Remove PLASTER GUARD (1) if attached.
Push CAPS (2 & 2a) as shown onto CONTROL
VALVES (3).
Push ESCUTCHEON HOLDER (4) with lightly greased
O-RING SEALS (5) over CAPS (2, 2a).
Attach the FIXATION PLATE (7) to the ESCUTCHEON
HOLDER (4) with the two SCREWS (6) provided.
Push ESCUTCHEON (8) flush against finished wall.
1
TRIM INSTALLATION
2
2a
1
4
5
6
3
7
M968026
3
3
4
TEMPERATURE ADJUSTMENT
SET HOT LIMIT STOP
Check that arrow marking B points to the 12 o'clock position. If not, push the BLACK CLAMP on the SECURING RING to
the right, pull off KNOB MOUNT (3) and reinstall KNOB MOUNT (3) with arrow "B" 12 o'clock position. See Figure 1.
For 100 F adjustment, turn the water supply on. Turn KNOB MOUNT (3) until the spout temperature is 100˚F. Check
that arrow "A" on the KNOB MOUNT (3) still points 12 o'clock position after adjusting the thermostat to 100˚F.
If not, pull out the RED LOCKING DEVICE. Remove KNOB MOUNT (3) by pulling it towards you while standing directly in
front of the valve.
Reinstall the KNOB MOUNT (3) with arrow "A" 12 o'clock position.
The maximum mixed water temperature is set at 109˚F at the factory. This setting can be changed if desired.
Remove the TEMPERATURE LIMIT STOP (H shaped Black Plastic part). Reinstall it at the desired notch as indicated in
the diagram to limit the maximum mixed water temperature to 104˚F or 112˚F.
Reinstall RED LOCKING DEVICE.
See Step 2 for HANDLE (2) installation.
Loosen SET SCREW (1). Pull off HANDLE ASSEMBLY (2).
ARROW
"A"
BLACK
CLAMP
ARROW
"B"
RED LOCKING
DEVICE
TEMPERATURE
LIMIT STOP
ARROWS AT 12 O'CLOCK
POSITION
Figure 1
KNOB MOUNT
112
109
104
1
2
MOMENTS
M968026
MODEL NUMBER
A907090-YYY0A
CAP
M908024-YYY0A
ESCUTCHEON
M909438-YYY0A
HANDLE SCREW
M962727-YYY0A
HANDLE KIT
CENTRAL THERMOSTAT
WITH VOLUME CONTROL
TRIM KIT
For toll-free information and answers to your questions, call:
1-800-442-1902
Weekdays 8:00 a.m. to 6:00 p.m. EST
IN CANADA 1-800-387-0369 (TORONTO 1-905-306-1093)
Weekdays 8:00 a.m. to 7:00 p.m. EST
IN MEXICO 01-800-839-12-00
Product names listed herein are trademarks of American Standard Inc.
© AS America, Inc. 2008
HOT LINE FOR HELP
M918038-0070A
ADAPTER
M918990-0070A
SELF TAPPING SCREW
Replace the "YYY" with
appropriate finish code
CHROME
STAINLESS STEEL
002
075
T506.740
M962635-YYY0A
ESCUTCHEON AND SCREWS
023774-0070A
SCREWS
A924335-0070A
FIXATION PLATE
Page is loading ...
Page is loading ...
Page is loading ...
M968026
NUMÉRO DU MODÈLE
A907090-YYY0A
CAPUCHON
M908024-YYY0A
ROSACE
M909438-YYY0A
VIS DE LA POIGNÉE
M962727-YYY0A
TROUSSE DE
LA POIGNÉE
THERMOSTAT CENTRAL
AVEC RÉGLAGE DE DÉBIT
JEU DE GARNITURE
T064.740
MOMENTS
Pour obtenir des renseignements ou une réponse
à vos questions, composez sans frais le :
1-800-442-1902
Jours de la semaine 8 h à 18 h HNE
AU CANADA 1-800-387-0369 (TORONTO 1-905-306-1093)
Jours de la semaine 8 h à 19 h HNE
AU MEXIQUE 01-800-839-12-00
Les noms des produits nommés ci-après sont des marques de commerce
déposées d’American Standard Inc.
© AS America, Inc. 2008
LIGNE D’URGENCE
M918038-0070A
ADAPTATEUR
M918990-0070A
VIS À AUTO-FILETAGE
Remplacer les lettres “YYY” par
le code de finition approprié
CHROME
ACIER INOXYDABLE
002
075
M962635-YYY0A
ROSACE ET VIS
A924335-0070A
PLAQUE DE FIXATION
023774-YYY0A
VIS DU SUPPORT À ROSACE
Page is loading ...
Page is loading ...
Page is loading ...
MOMENTS
M968026
NÚMERO DE MODELO
A907090-YYY0A
TAPA
M908024-YYY0A
CHAPETÓN
M909438-YYY0A
TORNILLO DE LA
MANIJA
M962727-YYY0A
JUEGO DE
LA MANIJA
TERMOSTATO CENTRAL
CON CONTROL DE VOLUMEN
JUEGO DE MOLDURA
T064.740
Llame sin costo para obtener información y respuestas a sus preguntas:
1-800-442-1902
De lunes a viernes de 8:00 a.m. a 6:00 p.m. hora del este de EE.UU.
EN CANADÁ 1-800-387-0369 (TORONTO 1-905-306-1093)
De lunes a viernes de 8:00 a.m. a 7:00 p.m. hora del este de EE.UU.
EN MÉXICO 01-800-839-12-00
Los nombres de productos que aparecen en este documento son marcas
comerciales de American Standard Inc.
© AS America, Inc. 2008
ASISTENCIA TELEFÓNICA
M918038-0070A
ADAPTADOR
M918990-0070A
TORNILLO AUTOROSCANTE
Reemplace las "YYY" con el código de
acabado correspondiente
CROMO
ACERO INOXIDABLE
002
075
M962635-YYY0A
CHAPETÓN Y TORNILLOS
023774-0070A
TORNILLOS
A924335-0070A
FIXATION PLATE
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
-
12
American Standard Moments T506.740 User manual
- Category
- Sanitary ware
- Type
- User manual
American Standard Moments T506.740 is a central thermostat with volume control. It has been certified to comply with ANSI A112.18.1M and ASSE 1016 standards. The device comes with a trim kit and has roughing-in dimensions of 160mm x 220mm x 100mm. It can be installed with either 1/2" NPT or 3/4" NPT inlets, and the fitting must be installed with the volume control on top. The device includes a plaster guard, caps, an escutcheon holder, an escutcheon, a fixation plate, handles, and a handle adapter.
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
in other languages
Related papers
-
American Standard T506.740.002 Installation guide
-
-
-
-
-
-
-
-
-