CleanShot 2050PSI Owner's manual

2050PSI
Brand
CleanShot
Model
2050PSI
Category
High-pressure cleaners
Type
Owner's manual

This manual is also suitable for

CleanShot TM ,
__lw POWERPRODUCTS
2050PSI
Owner's Manual/Manual del Propietario
Questions? Help isjust a moment away!
Preguntas? La ayudaes justaun momento lejos!
Call: Pressure Washer Helpline
Llame:Linea Directa del Lavador a Presi6n - 1-800-743-4115 M-F 8-5 CT
CleanShotTM isa trademark of Briggs& Stratton Power Products.
CleanShotTM es una marca registrada de Briggs& Stratton Power Products.
BRIGGS & STRATTON POWER PRODUCTS GROUP, LLC
IU!!!U!!U!!,,EFFERSO,,,,W,SCONS,,,,,U.S.A.
0 3 Model No.020206-0 (2050 PSIPressureWasher) ManualNo. 194140GS Revision I (01/26/2004)
CleanShotTM 2050 PSIPressureWasher
TABLE OF CONTENTS
SafetyRules.................................... 2-4
Know Your PressureWasher........................ 5
Assembly...................................... 6-7
Operation .................................... 8- I0
Product Specifications ............................ I I
Maintenance................................. I I- 13
Storage........................................ 14
Troubleshooting ................................. 15
Replacement Parts ............................ 16-17
Notes ......................................... 18
Warranty ...................................... 19
EQUIPMENT
DESCRIPTION
_Read this manual carefully and become familiar
with your pressure washer.Know its
applications, its limitations and any hazards
involved.
This manualcontains informationfor a pressure washer
that operates at 2,050 PSIat a flow rate of 2.0gallonsper
minute.This high quality residential system features axial
cam pump with stainless steel pistons, automatic cool down
system,chemical injection system,adjustable spray nozzle,
turbo nozzle, utility brush with adapter,tool bag,safety
goggles,heavyduty 25' hose,andmore.
Every effort hasbeen madeto ensure that information in
this manualis accurate and current. However, we reserve
the right to change,alter or otherwise improve the product
and this document at anytime without prior notice.
In the State of California a spark arrester is required by lawI
(Section 4442 of the California PublicResourcesCode). I
Other states may havesimilar laws.Federallawsapply on
federal lands.If you equip the muffler with a spark arrester,
it must be maintained in effective working order.
SAFETY RULES
This is the safety alert symbol. It is used to
alert you to potential personal injury hazards.
Obey all safety messages that follow this
symbol to avoid possible injury or death.
The safety alert symbol (_,) is used with a signalword
(DANGER, CAUTION,WARNING), a pictorial and/or a
safety messageto alert you to hazards.DAN('_I'R indicates
a hazard which, if not avoided,will result in death or serious
injury. WARNING indicatesa hazardwhich, if not avoided,
couldresult in death or serious injury. CAUTION
indicates a hazardwhich, if not avoided,might result in
minor or moderate injury. CAUTION, when used
without the alert symbol, indicates a situation that could
result in equipment damage.Follow safety messagesto
avoid or reduce the risk of injury or death.
WARNING I
The engine exhaust from this product contains I
chemicals known to the State of California to cause
cancer, b rth defects, or other reproduct ve harm.
Hazard Symbols and Meanings
Toxic Fumes Electrical Shock
Slippery Surface Fall Fluid Injection
Fire Explosion Hot Surface
Moving Parts FlyingObjects Kickback
/
2
CleanShotTM 2050 PSIPressureWasher
CleanShor
DANGER
Operate pressure washer ONLY outdoors.
Use a respirator or mask whenever there isa chance that
vapors may be inhaled.
Readall instructionswith maskso you are certain the maskwill
provide the necessaryprotection againstinhalingharmful vapors.
WARNING
Keepwater sprayawayfrom electric wiring or fatal electric
shock may result.
WARNING
Keepspray nozzle between 8 to 24 inchesawayfrom cleaning
surface.
Operate this unit on a stable surface.
The cleaning area should have adequate slopes and drainage to
reduce the possibility of afall due to slippery surfaces.
Beextremely careful ifyou must usethe pressure washer from
a ladder,scaffolding or anyother relatively unstable location.
Firmly grasp spraygun with both handswhen usinghigh
pressure sprayto avoid iniuryif gun kicks back.
WARNING
WHEN ADDING FUEL
Turn pressure washer OFF and let it cool at least 2 minutes
before removing gas cap.
Fill fuel tank outdoors.
DO NOT overfill tank.Allow space for fuel expansion.
Keep fuel away from sparks, open flames, pilot lights, heat, and
other ignition sources.
DO NOT light a cigarette or smoke.
¢VHEN OPERATING EQUIPMENT
DO NOT tip engine or equipment at angle which causes fuel
to spill.
DO NOT spray flammable liquids.
'HEN TRANSPORTING OR REPAIRING EQUIPMENT
Transport/repair with fuel tank EMPTY or with fuel shutoff
valve OFE
_HEN STORING FUEL OR EQUIPMENT WITH FUEL
IN TANK
Store away from furnaces, stoves, water heaters, clothes
dryers or other appliances that have pilot light or other
ignition source because they can ignite fuel vapors.
WARNING
NEVER aim spray gunat people, animalsor plants.
DO NOT allow CHILDREN to operate pressure washe_
NEVER repair high pressure hose.Replaceit.
Keep high pressure hose connected to pump and spray gun
while system is pressurized.
ALWAYS RELIEVEwater pressure each time engine is stopped
by squeezingtrigger on spray gun.
/
3
CleanShotTM 2050 PSIPressureWasher
WARNING
DO NOT touch hot surfaces.
Stay dear of exhaust gases.
Allow equipment to cool before touching.
WARNING
DO NOT wear loose clothing, jewelry or anything that may
be caught in the starter or other rotating parts.
Tie up long hair and remove jewelry.
WARNING
Always wear eye protection when using this equipment or in
vicinity of where equipment is in use.
WARNING
Disconnect spark plug wire from spark plug and place wire
where it cannot contact spark plug.
CAUTION
DO NOT tamper with governed speed.
DO NOT operate pressure washer above rated pressure.
CAUTION
DO NOT secure spraygun in open position.
DO NOT leavespray gun unattended while machine is
running.
NEVER use aspray gunwhich does not haveatrigger lock or
trigger guard in placeand in working orde_
Always be certain spraygun,nozzles and accessories are
correctly attached.
CAUTION
DO NOT point spraygun at glasswhen in iet spray mode.
NEVER aim spray gunat plants.
CAUTION
tf you have questions about intended use,askdealer or
contact Briggs& Stratton Power Products.
NEVER operate units with broken or missing parts, or
without protective housing or covers.
DO NOT by-pass any safetydevice on this machine.
Before starting pressure washer in cold weather, check all
parts of the equipment to be sure ice has not formed there.
NEVER move machine by pulling on high pressure hose.Use
handle provided on unit.
Check fuel system for leaksor signsof deterioration, such as
chafed or spongy hose,loose or missingclamps,or damaged
tank or cap.Correct all defects before operating pressure
washe_
This equipment is designed to be used with Briggs& Stratton
Power Products authorized parts ONLY. If equipment isused
with parts that DO NOT comply with minimum specifications,
user assumesall risks and liabilities.
/
4
CleanShotTM 2050 PSIPressureWasher
CleanShot
KNOWYOUR PRESSURE WASHER
Read this owner's manual and safety rules before operating your pressure washer.
Compare the illustrationswith your pressure washer to familiarize yourself with the locations of various controls and
adjustments. Savethis manualfor future reference.
Air Cleaner
Recoil Starter
\
Primer Bulb
High Pressure Outlet
& Water Inlet
FueiTank
Air Cleaner-- Dry type filter element limits the amount
of dirt and dust that gets in the engine.
Automatic Cool Down System -- Cycles water
through pump when water reaches 125°-155°F.Warm
water will discharge from pump onto ground.This
system prevents internal pump damage.
Fuel Tank- FIlltank with regular unleaded fuel.
High Pressure Hose (not shown) -- Connect one end
to water pump and the other end to spraygun.
High Pressure Outlet -- Connection for high pressure
hose.
Pump equipped with
Automatic Cool Down System
DataTag (not shown, near rear of base plate) -
Provides model and serial number of pressure washer.
Pleasehavethese readily availableifcalling for assistance.
Primer Bulb -- Preparesa cold enginefor starting.
Pump -- Devetops high water pressure.
Recoil Starter -- Used for starting the engine manually.
Spray Gun (not shown) -- Controls the application of
water onto cleaningsurfacewith trigger device.Includes
safety latch.
Water Inlet -- Connection for garden hose.
I
5
CleanShotTM 2050 PSIPressureWasher
CleanShot
ASSEMBLY
IMPORTANT: Readentire owner's manualbefore you
attempt to assembleor operate your new pressure washer.
Remove Pressure Washer From
Carton
I. Removethe parts bag,accessories,and insertsincluded
with pressure washer.
2. Slicetwo corners at the end of carton from top to
bottom so the panel can be folded clown fiat.
3. Removepressure washer from carton.
Carton Contents
Items in the carton include:
Main Unit
High Pressure Hose
SprayGun
Nozzle Extension
Turbo Nozzle
Utility Brushwith Adapter
Accessory Storage Bag
SafetyGoggles
Oil Bottle
Parts Bag(which includesthe following):
Owner's Manual
EngineManual
Owner's Registration Card
PREPARING PRESSURE
WASHER FOR USE
If you haveanyproblems with the assemblyof your
pressure washer or if parts are missingor damaged,callthe
pressure washer helpline at 1-800-743-4115. If callingfor
assistance,pleasehavethe model, revision, and serial
number from the data tag available.
To prepare your pressure washer for operation, you
will need to perform these tasks:
I. Fill out and sendin registration card.
2. Add oil to engine crankcase.
3. Add fuel to fuel tank.
4. Connect high pressure hoseto spraygun and pump.
5. Connect water supply to pump.
6. Attach nozzle extension to spray gun.
Add Engine Oil and Fuel
• Placepressure washer on a level surface.
CAUTION
• Refer to engine manualfor oil andfuel fill information.
• Damage to equipment resulting from failure to follow this
instructionwill void warranty.
• Refer to engine owner's manual and follow oil and fuel
recommendations and instructions.
NOTE: Check oil often during engine break-in. Refer to
engine owner's manual for recommendations.
/
6
CleanShotTM 2050 PSIPressureWasher
Connect Hose and Water Supply to
Pump
IHPORTANT: To avoid pump damage,you must assemble
the nozzle extension to the spray gun and attach atl hoses
before you start the engine.
I. Uncoil high pressure hose and attach one end of hose
to baseof spray gun (Figure I).Tighten by hand.
Connect high pressure
hose here
NOTE: Remove and discard alt pump shippingcaps before
attaching hoses.
2. Attach other end of high pressure hoseto high
pressure outlet on pump (Figure 2).Tighten by hand.
4. Run water through your garden hose for 30 seconds
to cleanout any debris.
IMPORTANT: DO NOT siphon standing water for the
water supply.Use ONLY cold water (less than IO0°E).
5. Connect the garden hose (not to exceed 50 feet in
length)to the water inlet.Tightenby hand (Figure 3).
CAUTION
• Damage to equipment resulting from failure to follow this
instructionwill voidwarranty.
6. Turn ON the water and squeezethe trigger on the
gun to purge the pump system of air and impurities.
WARNING
Always wear eye protection when usingthis equipment or in
vicinity of where equipment isin use.
Before starting the pressure washer,be sure you are wearing
adequate eye protection.
.
Before connectinggarden hoseto water inlet,inspect
inlet screen (Figure 3). Clean screen if it contains
debris or haveit replaced ifdamaged.DO NOT RUN
PRESSUREWASHERIF INLET SCREENISDAMAGED.
Inspectintet
screen,DONOT
useif damaged;
cleanif dirty.
CHECKLIST BEFORE
STARTING ENGINE
Review the unit's assemblyto ensure you haveperformed
altof the following.
I. Check that oit hasbeen added to proper level in the
engine crankcase.
2. Add proper gasoline to fuel tank.
3. Check for properly tightened hose connections.
4. Check to make sure there are no kinks,cuts, or
damageto high pressure hose.
5. Provide a proper water supply at an adequateflow.
6. Be sure to read "Safety Rules" and"HowTo UseYour
PressureWasher" before usingpressure washer.
/
7
CleanShotTM 2050 PSIPressureWasher
CleanShot
HOW TO USE YOUR
PRESSURE WASH ER
If you haveanyproblems operating your pressurewasher,
pleasecall the pressurewasher helpline at 1-800-743-4115.
How to StartYour Pressure Washer
To start your pressure washer for the first time, follow
these instructions step-by-step.This starting information
also appliesif you havelet the pressure washer sit idlefor
at least a day.
I. Placepressure washer near an outside water source
capableof supplying water at a flow rate greater than
3.0gallons per minute and no lessthan 20 PSIat
pressure washer end of garden hose.
2. Check that high pressure hose is tightly connected to
spray gun and pump. See"PreparingPressureWasher
for Use" for illustrations.
3. Make sure unit is in a level position.
4. Connect garden hose to water inlet on pressure
washer pump. Turn ON water.
CAUTION
• Damage to equipment resulting from failure to follow this
instruction will void warranty.
5. Attach adjustable nozzle extension to spray gun
(Figure 4).Tighten by hand.
6.
Position nozzle in low pressure mode (see"How to
Use the Adjustable Nozzle") andsqueezetrigger on
spray gun to relieve air pressure caused by turning ON
water.Water will flow out of spray gun in a thin
stream. Continue to hold trigger until there is a steady
stream of water and no air remains in system.This wilt
make it easier to pull start engine.Releasetrigger.
7. Engage safety latch to spray gun trigger (Figure 5).
SafetyLatch
8. Start engine according to instructions given in engine
owner's manual.
• Squeezetriggeron sprayguneachtime recoilstarter is
pulledandenginefailsto start.
NOTE: Always keep the throttle lever in the "Fast"
position when operating the pressure washer.
How to StopYour Pressure Washer
I. Let engine idle for two minutes.
2. Turn engine off according to instructions given in
engine owner's manual.
3. Squeeze trigger on the spray gun to relieve
pressure in the hose.
NOTE: A small amount of water will squirt out when you
releasethe pressure.
How to Use the Adjustable Nozzle
You should now know how to START and STOP your
pressure washer.The information in this section will tell
you how to adjust the spray pattern and to apply detergent
or other cleaningchemicals.
CAUTION
I.
NEVER adjust spray pattern when spraying.
NEVER put handsin front of nozzle to adiust spray pattern.
Slide nozzle forward when you wish to adjust spray to
low pressure mode (Figure 6). Slide nozzle backward
to achieve high pressure.
I
8
CleanShotTM 2050 PSIPressureWasher
CleanShot
2.
Slide nozzle backward
for High Pressure
Mode
Slide nozzle forward for low
pressure mode and
detergent application
Point nozzle down towards a firm surface and press
trigger to test pattern (Figure 7).
3. Twisting nozzle adjusts spray pattern from a narrow
pattern to a fan pattern (Figure 8).
Rotate nozzle
counterclockwise for fan
spray pattern
Rotate nozzle clockwise
for narrow spray pattern
4. For most effective cleaning,keep spraynozzle from
8 to 24 inches awayfrom cleaning surface.
5. If you get spray nozzle too close,especiallyusinghigh
pressure mode, you may damagesurfacebeing cleaned.
6. DO NOT get closer than 6 inches when cleaningtires.
Using the Turbo Nozzle
The turbo nozzle rotates the high pressure stream in a
rapid circular pattern.The high pressure spray is most
effective when the tip of the nozzle extension is held
between 8 to 24 inches from the surface being cleaned.
CAUTION
Always make sure the surface you will clean will not be
damaged by the high pressure spray by testing in a hidden area.
To attach the turbo nozzle to the spray gun:
I. Engagesafety latch to sprayguntrigger.
2. Remove the nozzle extension from the spray gun,if
attached.
3. Attach the turbo nozzle extension to spray gun
(Figure 9).Tighten by hand.
4.
5.
\
Disengagesafety latch to spray gun trigger.
Always start the turbo nozzle at a distance,gradually
getting closer to the surface until you get the cleaning
force you want.
NOTE: Detergent cannot be applied with turbo nozzle.
Using the Utility Brush
The utility brush allows you to scrub surfaces with water
filtering through the bristles.
To attach the utility brush to the spray gun:
I. Engagesafety latch to spraygun trigger.
2. Tighten the adapter to the brush base.
3. Remove the nozzle extension from the spray gun,if
attached.
/
9
CleanShotTM 2050 PSIPressureWasher
CleanShot
4. Attach the brush with the adapter to the spray gun.
Tighten by hand (Figure 10).
NOTE:You must usethe adapter to attach the brush to
the spray gun.
5. Disengagesafety latch to spray gun trigger.
Applying Detergent with the
Adjustable Nozzle
IMPORTANT: Use soaps designed specifically for
pressure washers. Household detergents could damage
the pump.
CAUTION
• Starting the engine without all the hosesconnected and
without the water turned ON will damagethe pump.
• Damage to equipment resulting from failure to follow this
instruction will void warranty.
To apply detergent, follow these steps:
I. Reviewuse of adjustable nozzles.
2. Preparedetergent solution asrequired by job.
3. Placefilter end of chemical injection hose into
detergent container.
CAUTION
• When inserting the filter into a detergent solution bottle,
route the tube so asto keep it from inadvertentlycontacting
the hot mufflen
4. Slide adjustable nozzle forward to low pressure mode.
Detergent cannot be applied with nozzle in high
pressure position.
5. Makesure garden hose is connected to water inlet.
Check that high pressure hose isconnected to spray
gun and pump. Start engine.
6. Apply detergent to a dry surface,starting at lower
portion of area to be washed and work upward, using
long,even,overlapping strokes.
7. Allow detergent to "soak in"for 3-5 minutes before
washingand rinsing. Reapplyas needed to prevent
surface from drying. DO NOT allow detergent to dry
on (prevents streaking).
IMPORTANT:You must flush the chemical injection
system after eachuse by placingthe filter into a bucket of
cleanwater, then run the pressure washer in low pressure
for I-2 minutes.
Pressure Washer Rinsing
For Rinsing:
I. Slide the nozzle backward to high pressure, pressthe
trigger and wait for the detergent to clear.
NOTE:You can also stop detergent from flowingby simply
removing chemical injection hose from bottle.
2. Keep the spraygun a safe distancefrom the area you
plan to spray.
WARNING
Keepspray nozzle between 8 to 24 inchesawayfrom cleaning
surface.
Operate this unit on a stable surface.
Be extremely careful if you must usethe pressurewasher from
a ladder,scaffolding or anyother relatively unstable location.
Firmlygrasp spraygunwith both handswhen using high
pressure sprayto avoid iniuryif gun kicks bac!c
3. Apply a high pressure spray to a small area,then check
the surfacefor damage.If no damageisfound, it isokay
to continuecleaning.
4. Start at the top of the areato be rinsed,working
down with same overlapping strokes asyou usedfor
washingand applyingdetergent
Automatic Cool Down System
(Thermal Relief)
If you run the engine on your pressure washer for
3-5 minutes without pressingthe trigger on the spray gun,
circulating water in the pump can reachtemperatures
above 125°EThe system engagesto cool the pump by
discharging the warm water onto the ground.
/
10
SPECIFICATIONS
Outlet Pressure ..... 2050 psi
Flow Rate .......... 2.0 gallonsper minute (gpm)
Detergent .......... Use detergent approvedfor
pressure washers
Water Supply ...... Not to Exceed 100°F
Temperature
Automatic Cool .... Willcyclewhen water
Down System reaches 125°-155°F
ShippingWeight .... 48 Ibs.
GENERAL MAINTENANCE
RECOMMENDATIONS
The pressure washer warranty does not cover items that
have been subjected to operator abuse or negEgence.To
receive full value from the warranty, the operator must
maintain the pressure washer as instructed in this manual
• Some adjustments witl need to be made periodically to
properly maintain your pressure washer.
• All maintenance in this manual and the engine owner's
manual should be made at least once each season.
• Once a year you should clean or replace the spark plug,
clean or replace the air filter and check the spray gun
and adjustable nozzle extension assembly for wear.A
new spark plug and clean air filter assure proper fuel-air
mixture and help your engine run better and last longer.
Please refer to your engine owner's manual for more
details.
• If equipped with inflatabletires, keep the air pressure at
the value marked on the tire or within 15 and 40 psi.
Before Each Use
I. Check engine oil level.
2. Check water inletscreen for damage.
3. Check in-line filter for damage.
4. Check high pressure hose for leaks.
5. Check chemical injectionhose and filter for damage.
6. Check spray gun and adjustable nozzle extension
assemblyfor leaks.
7. Rinseout gardenhose to flush out debris.
PRESSURE WASH ER
MAINTENANCE
Check and Clean Inlet Screen
Examinethe screen on the water inlet.Clean it ifthe
screen isclogged or replace it ifscreen is damaged.
Check High Pressure Hose
The high pressure hose can develop leaksfrom wear,
kinking,or abuse.Inspect the hoseeach time before using
it. Check for cuts,leaks,abrasions or bulging of cover,
damageor movement of couplings.If anyof these
conditions exist, replacethe hose immediately.
WARNING
NEVER repair high pressure hose. Replace it.
Replacement hose rating MUST exceed maximum pressure
rating of unit.
Check Chemical Injection Hose
Examinethe filter on the detergent tube and clean if
clogged.The tube should fit tightly on the barbed fitting.
Examine the tube for leaks or tears. Replace the filter or
tube if either is damaged.
Check Gun and Adjustable Nozzle
Extension
Examinethe hose connection to the spray gun and make
sure it is secure.Test the trigger by pressingit and making
sure it "springs back" into place when you releaseit. Put
the safety latch in the ON position and test the trigger.You
should not be able to press the trigger.
Purge Pump of Air and
Contaminants
To remove air from the pump, follow these steps:
I. Set up pressure washer asdescribed in"Preparing
PressureWasher For Use". Connect water supply and
turn water on.
I
II
CleanShot TM 2050 PSI Pressure Washer
CleanShot
2. Pulltrigger on spray gun and hold.
3. When water supply is steadyand constant, engage
safety latch.
To remove contaminants from the pump, follow
these steps:
I. Set up pressure washer asdescribed in"Preparing
PressureWasher For Use". Connect water supply and
turn water on.
2. Remove nozzle extension from spray gun.
3. Start engine according to instructions in"HowTo Use
Your Pressure Washer".
4. Squeeze trigger on spray gun and hold.
5. When water supply is steadyand constant, engage
safety latch and refasten nozzle extension.
Check In-Line Filter
Refer to Figure I I and service the in-linefilter if it
becomes dogged, asfottows:
I.
2.
iB_l_lrl1_g_ m_ i_l'_'_r_
.
4.
O-tin
Detachspray gun and nozzle extension from high
pressure hose. Detach nozzle extension from spray
gun and remove o-ring and screen from nozzle
extension. Flush screen,spraygun,and adjustable
nozzle extension with cleanwater to clear debris.
Placein-line filter screen into threaded end of nozzle
extension. Direction does not matter. Pushscreen in
with eraser end of pencil until it rests flat at bottom of
opening.Takecare not to bend the screen.
Placeo-ring into recess.Pusho-ring snugly againstin-
line filter screen.
Assemble nozzle extension to spray gun,asdescribed
earlier in manual.
Nozzle Maintenance
A pulsingsensation felt while squeezingthe spraygun
trigger may be caused by excessivepump pressure.The
principal cause of excessivepump pressure is a nozzle
cloggedor restricted with foreign materials, such asdirt,
etc.To correct the problem, immediately cleanthe orifice
following these instructions:
I. Shut off engine and turn off water supply.
2. Remove orifice from end of nozzle extension. Separate
nozzle extension from spray gun.Twist nozzle
clockwise to stream position. Using a 2mm (5/64) allen
wrench, remove orifice from end of nozzle extension
(Figure 12).
Orifice
3. Remove in-line filter from other end of nozzle
extension.
4.
5.
Use a small paper clip to free anyforeign material
cloggingor restricting orifice (Figure 12).
Using a garden hose, remove additional debris by back
flushing water through nozzle extension (Figure 13).
Back flush between 30 to 60 seconds.Turn adjustable
nozzle extension to stream spray and move nozzle
from low to high while flushing.
/
12
CleanShotTM 2050 PSIPressureWasher
CleanShot
6. Reinstallorifice and in-line filter into nozzle extension.
DO NOT overtighten orifice with allen wrench.
7. Reconnect nozzle extension to spraygun.
8. Reconnect water supply,turn on water,and start
engine.
9. Test pressure washer by operating with nozzlein high
and low positions.
O-Ring Maintenance
Purchasean O-Ring/Maintenance Kit, part number
191922GSby contacting the nearest authorized service
center. It is not included with the pressure washer.This kit
includes replacement o-rings, rubber washer and water
inlet filter. Refer to the instruction sheet provided in the kit
to service your unit's o-rings.
Cleaning Chemical Injection Hose
Ifyou used the chemical injectionhose,you must flush it
with cleanwater before stopping the engine.
I. Placechemical injection hose in a bucket full of clean
w_ter.
2. Slide adjustable nozzle forward to low pressure
position. Flushfor I-2 minutes.
3. Shut off engine.
IMPORTANT: Simply shutting OFF engine will not
releasepressure in the system.When the engine has
shut down, squeeze the trigger on the spray gun to
relieve the pressure in the hose.
Pump Maintenance
Changing Pump Oil
Change oil every 50 hours or once yearly, whichever
occurs first.
NOTE: Purchase a premeasured bottle of pump oit, item
number 190586GS, by contacting the nearest authorized
service center.
Change pump oil as follows:
I. Drain engine oil and fuel from pressure washer.
2. Use a 8mm allen wrench to remove black pump oil
capbetween high pressure outlet and garden hose
inlet (Figure 14).
Cap
3. Tilt pressure washer to drain oil into an approved
container until it drips slowly from pump.
4. Tilt pressure washer in opposite direction andempty
premeasured pump oil bottle into sameopening (a
small funnel may be helpful).
5. Install black pump oil cap and tighten firmly.
6. Set pressure washer in upright position.Acid fuel and
engine oil.
ENGINE MAINTENANCE
See the engine owner's manual for instructions on how to
properly maintain the engine.
CAUTION
Used motor oil has been shown to cause skin cancer in
certain laboratory animals.
Thoroughly wash exposed areaswith soap and water.
i_ KEEPOUT OF REACH OF CHILDREN. DON'T
POLLUTE.CONSERVE RESOURCES.RETURN
USED OIL TO COLLECTION CENTERS.
/
13
CleanShotTM 2050 PSIPressureWasher
CleanShot
PREPARING THE UNIT
FOR STORAGE
Water should not remain in the unitfor longperiods of
time. Sedimentsor minerals candeposit on pump parts and
"freeze" pump action. If you do not plan to usethe
pressure washer for more than 30 days,follow this
procedure:
I. Flushchemical injectionhose by placing filter into a pail
of cleanwater while running pressure washer in low
pressure mode (adjustable nozzle inforward position).
Flushfor one to two minutes.
2. Shut off engine and let it cool, then remove high
pressure and garden hoses.Disconnect spark plug wire
from spark plug.
3. Placethe spray gun,nozzle extension, turbo nozzle,
utility brush with adapter and high pressure hose in the
accessory storage bag.
4. Empty pump of allpumped liquids by pulling recoil
handle about 6 times.This should remove most liquid
in pump.
5. Use PumpSaverto prevent corrosion build up and
freezing of pump.
6. Store unitin a clean,dry area.
Protecting the Pump
To protect the pump from damagecaused by mineral
deposits or freezing,use PumpSaverto treat pump.This
prevents freeze damageand lubricates pistons and seals.
NOTE: PumpSaveris availableas anoptional accessory.It
is not included with the pressure washer.Contact the
nearestauthorized servicecenter to purchasePumpSaver.
CAUTION
• Failure to do so will permanently damage your pump and
renderyour unit inoperable.
• Freezedamageisnot coveredunderwarranty.
CAUTION
Always wear eye protection when using PumpSaver.
To use PumpSaver, make sure the pressure washer is
turned off and disconnected from supply water. Read and
follow all instructions and warnings given on the PumpSaver
container.
NOTE: PumpSaverwill drip from pump after treatment
and will stain wood and concrete.
NOTE: If PumpSaveris not available,draw RVantifreeze
(non-alcohol) into the pump by pouring the solution into a
3-foot section of garden hose connected to inlet adapter
and pulling recoil handle twice.
STORING THE ENGINE
See the engine owner's manual for instructions on how to
properly prepare the engine for storage.
I
14
CleanShot TM 2050 PSI Pressure Washer
CleanShor
TROUBLESHOOTING
Problem
Pump has following problems:
failure to produce pressure, erratic
pressure, chattering, loss of
pressure, low water volume.
Detergent fails to mix with spray.
Cause
I. Nozzle in low pressure mode.
2. Water inlet isblocked.
3. Inadequatewater supply.
4. Inlet hose iskinked or leaking.
5. Clogged inlet hosestrainer.
6. Water supply isover 100°E
7. High pressure hose isblocked or
leaks.
8. Gun leaks.
9. Nozzle isobstructed.
10. Pump isfaulty.
I.
2.
3.
4.
Detergent siphoning tube isnot
submerged.
Chemical filter isclogged or
cracked.
Dirty in-line filter.
Nozzle is in high pressure mode.
Correction
I. Pull nozzle backward for high
pressure mode.
2. Clear inlet.
3. Provide adequate water flow.
4. Straighten inlet hose, patch leak.
5. Check and clean inlet hose
strainer.
6. Provide cooler water supply.
7. Clear blocks in outlet hose.
8. Replacegun.
9. Clean nozzle.
10. Contact Briggsand Stratton Power
Products service facility.
I. Insert detergentsiphoning tube
into detergent.
2. Clean or replace filter/detergent
siphoning tube.
3. See"Check In-Line Filter".
4. Push nozzle forward for low
pressure mode.
Engine speed istoo slow. Move throttle control to FAST
Engine runs good at no-load but position. If engine still "bogs down",
"bogs" when load is added, contact Briggsand Stratton service
facility.
Pressure washer stops during Out of gasoline. Fill fuel tank.
operation.
/
15
CleanShotTM 2050 PSIPressureWasher
I
i
EXPLODED VIEWAND PARTS LIST- MAIN UNIT
2
7
11_1 8
Item Part #
I 194494GS
2 B5693GS
3 192525GS
4 88935GS
5 192310GS
6 88185GS
7 193482GS
Description
ASSY,BASE
HOSE
KIT,Pump/EngineMounting
Hardware
ADAPTER, Extension Brush
KIT,Vibration Mount
BRUSH,Utility
GUN
Item Part #
8 194344DGS
9 194343BGS
l0 BI236DGS
I1 23139GS
12 194216GS
13 BI237DGS
900 NSP
Description
ASSY,Wand, Hi-Lo
ASSY,Wand,Turbo
ORIFICE
KEY
ASSY,Pump (see page 17)
ORIFICE
ENGINE
Items Not Illustrated:
Part#
194140GS
191460GS
194481GS
BB3061BGS
Description
MANUAL, Owner's
MANUAL, Engine
KIT,Decals,SRV
OIL, Engine
/
16
I
i
CleanShotTM 2050 PSIPressureWasher
CleanShot
EXPLODEDVIEWAND PARTS LIST- PUMP
E
®
H
Item Part #
19 190571GS
28 190627GS
29 190575GS
30 190576GS
34 190577GS
45 190578GS
46 190629GS
47 190630GS
62 190581GS
68 190582GS
69 190584GS
76 194298GS
Description
CAP,Oil
MANIFOLD
O-RING
SCREW
CONNECTION, Chemical Inlet
PIN
VALVE,Seat Plate,Plastic
VALVE,Seat,Plastic
CAP
BALL,SS
O-RING
THERMO RELIEF
Item Part #
A NSP
B 190632GS
C 190634GS
E 190591GS
F 190592GS
G 190593GS
H 190628GS
J 189971GS
K 190636GS
Description
ASSY,CASE,PISTON
KIT,WATER INLET,ALUM
KIT,OUTLET,ALUM
KIT,CHECK VALVES
KIT,INLET CHECK
KIT,CHEMICAL INJECTION
KIT,UNLOADER STEM
KIT,CHEMICAL HOSE
KIT,SEALSET
NOTE: Item letters B - K are service kits and include a((
parts shown within the box.
/
17
CleanShotTM 2050 PSIPressureWasher
NOTES
/
18
Effective January 1, 2003 replaces all undated Warranties and all Warranties dated before January 1, 2003
LIMITED WARRANTY
Briggs & Stratton Power Products Group, LLC will repair or replace, free of charge, any part(s), of the equipment that is defective in material
or workmanship or both. Transportation charges on parts submitted for repair or replacement under this warranty must be borne by
purchaser. This warranty is effective for the time periods and subject to the conditions stated below. For warranty service, find the nearest
Authorized Service Dealer in our dealer Iocator map at www.briggspowerproducts.com.
THERE IS NO OTHER EXPRESS WARRANTY. IMPLIED WARRANTIES, INCLUDING THOSE OF MERCHANTABILITY AND FITNESS
FOR A PARTICULAR PURPOSE, ARE LIMITED TO ONE YEAR FROM PURCHASE, OR TO THE EXTENT PERMITTED BY LAW ANY
AND ALL IMPLIED WARRANTIES ARE EXCLUDED. LIABILITY FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES ARE EXCLUDED
TO THE EXTENT EXCLUSION IS PERMITTED BY LAW. Some states or ceuntries do not allow limitations on how long an implied warranty
lasts, and some states or countries do not allow the exclusion or limitation of incidental or consequential damages, so the above limitation
and exclusion may not apply to you. This warranty gives you specific tsgal rights and you may also have other rights which vary from state
to state or country to country.
OUTBOARD
¸¸¸¸¸¸¸¸¸¸¸¸¸MOTOR¸¸¸¸¸¸¸¸¸¸¸¸¸¸¸
WELDER
Consumer Use
Commercial Use
The engine and starting batteries are warranted solely by the manufacturers of those products.
2 years for all consumer products in the European Union Parts only on 2nd year for consumer use of Portable Generator and
Home Generator System - Less than 10 KW, outside of European Union
The warranty period begins on the date of purchase by the first retail consumer or commercial end user, and continues for the period of time
stated in the table above. "Consumer use" means personal residenfia] household use by a retail consumer. "Commercial use" means all other
uses, including use for commercial, income producing or rental purposes. Once equipment has experienced commercial use, it shall thereafter
be considered as commercial use for purposes of this warranty. Equipment used for Prime Power in place of utility are not applicable to
this warranty. Electric Powered Pressure Washers used for commercial purposes are not warranted.
NO WARRANTY REGISTRATION IS NECESSARY TO OBTAIN WARRANTY ON BRIGGS & STRATTON PRODUCTS. SAVE YOUR
PROOF OF PURCHASE RECEIPT. IF YOU DO NOT PROVIDE PROOF OF THE INITIAL PURCHASE DATE AT THE TIME WARRANTY
SERVICE iS REQUESTED, THE MANUFACTURING DATE OF THE PRODUCT WILL BE USED TO DETERMINE THE WARRANTY
PERIOD.
We welcome warranty repair and apologize to you for being inconvenienced. Any Authorized Service Dealer may perform warranty repairs. Most
warranty repairs are handled routinely, but sometimes requests for warranty service may not be appropriate. For example, warranty service would not
apply if equipment damage occurred because of misuse, lack of routine maintenance, shipping, handling, warehousing or improper installation.
Similarly, the warranty is void if the manufacturing date or the serial number on the equipment has been removed or the equipment has been altered
or modified. During the warranty pedod, the Authorized Service Dealer, at its option, will repair or replace any part that, upon examination, is found to
be defective under normal use and service. This warranty will not cover the following repairs and equipment:
Normal Wear: Outdoor Power Equipment, like all mechanical devices, needs periodic parts and service to perform well. This warranty does not
cover repair when normal use has exhausted the life of a part or the equipment.
Installation and Maintenance: This warranty does not apply to equipment or parts that have been subjected to improper or unauthorized
installation or alteration and modification, misuse, negligence, accident, overloading, overspeeding, improper maintenance, repair or storage so as,
in our judgment, to adversely affect its performance and reliability. This warranty also does not cover normal maintenance such as adjustments,
fuel system cleaning and obstruction (due to chemical, dirt, carbon, lime, etc.).
Other Exclusions: This warranty excludes wear items such as quick couplers, oil gauges, belts, o-rings, filters, pump packing, etc., pumps that
have been run without water supplied or damage or malfunctions resulting from accidents, abuse, modifications, alterations, or improper servicing
or freezing or chemical deterioration. Accessory parts such as guns, hoses, wands and nozzles are excluded from the product warranty. Also
excluded is used, reconditioned, and demonstration equipment; equipment used for prime power in place of utility power and equipment used in
life support applications.
BRIGGS & STRATTON POWER PRODUCTS GROUP, LLC
JEFFERSON, WI, USA
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Lavadorade Presi6n 2050 PSIde CleanShotTM
CleanShot
NOTAS
/
33
Page is loading ...
Page is loading ...
Page is loading ...
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36

CleanShot 2050PSI Owner's manual

2050PSI
Brand
CleanShot
Model
2050PSI
Category
High-pressure cleaners
Type
Owner's manual
This manual is also suitable for
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

in other languages

Other documents