Assembly
Fitting the accessories (g. A & C)
These models are supplied with the following
accessories:
- a crevice tool (7) for conned spaces
- a brush tool (8) for furniture and stairs
To t an accessory, proceed as follows:
•Take the accessories from the appliance.
•Insert the appropriate accessory into the front
of the appliance.
Use
•Before charging, preferably discharge the
battery by operating the appliance until motor
slows (DO NOT run until the motor stops)
•Before rst use, the battery must be charged
for at least 16 hours. Place the appliance on
the charging base whenever it is not in use.
Charging the battery (g. B)
•Make sure that the appliance is switched off.
The battery will not be charged with the on/off
switch in the on position.
•Place the appliance on the charging base as
shown.
•Plug in the charger. Switch on at the mains.
The charging indicator (6) will be lit.
•Leave the appliance to charge for at least 16
hours.
Whilst charging, the charger may become Warm. This is
normal and does not indicate a problem. The appliance
can be left connected to the charger indenitely. The
charging indicator will be lit as long as the appliance is
connected to the plugged-in charger.
Warning! Do not charge the battery at ambient
temperatures below 4 °C or above 40 °C.
Switching on and off (g. D)
•1 Speed Model: To start, slide on/off switch
forward to “1”(ie 0=off 1=on). To stop slide
the switch back to “0”.
•2 Speed Model: To start, slide on/off switch
forward (ie 0=off, 1 = low speed, 2= high speed). To stop
slide back to position “0”
CV9605/CV1205/CHV9600/CHV1200/CHV1440
- Optimising the suction force (g. E)
In order to keep the suction force optimised, the lter
must be cleared regularly during use.
•Rotate the wheel (5) a few turns to shake out
dust clogging the lter (9).
Cleaning and maintenance
Warning! Regularly clean the lters.
Cleaning the dust bowl and lters
(g. F - I)
The lters are re-usable and should be cleaned regularly.
•Press the release button (2) and remove the
dust bowl (3) (g. F).
•Empty the dust bowl (g. G).
•Remove the lters (9 & 10) by twisting them
clockwise (g. H).
•Brush any loose dust off the lters.
•
Wash the lters in warm, soapy water (g. I).
The bowl can also be washed if necessary.
Do not immerse the appliance in water (g. J).
•Make sure the dust bowl and lters are dry.
•Ret the lters (9 & 10) onto the appliance,
twisting them counterclockwise until they lock
into place.
•Ret the dust bowl onto the appliance. Make
sure the dust bowl clicks into place.
Warning! Never use the appliance without the lters.
Optimum dust collection will only be achieved with clean
lters and an empty dust bowl.
CV7205/CV9605/CV1205/CHV7200/
CHV9600/CHV1200/CHV1440-
Cleaning
the exhaust lter (g. K)
•Open the lid (11).
•Remove the lter (12) from the recess.
•Wash the lter in warm, soapy water.
•Make sure the lter is dry.
•Ret the lter (12).
•Close the lid.
Replacing the lters
The lters should be replaced every 6 to 9 months and
whenever worn or damaged. Replacement lters are
available from your Black & Decker dealer (cat. no.
VF40).
Remove the old lters as described
above. Fit the new lters as described above.
Protecting the environment
Should you nd one day that your Black &
Decker product needs replacement, or if it is of
no further use to you, think of the protection of
the environment. Black & Decker repair agents
will accept old Black & Decker products and ensure that
they are disposed of in an environmentally safe way.
Battery (g. L - N)
If you want to dispose of the product yourself, the
battery must be removed as described below and
disposed of in accordance with local regulations.
•Preferably discharge the battery by perating
the appliance until the motor stops.
The battery is located under the back end of the
appliance.
•Take the accessories from the appliance.
•Remove the screws (13).
•Unlock the tabs (14) holding the accessory
holder in place.
•Remove the accessory holder (15).
•Remove the screws (16) holding the battery
in place.
•Slide the battery (17) backward as shown.
•Remove the battery.
•Place the battery in a suitable packaging