Barco ULTRA REALITY 7000 R9002810 User manual

BARCO PROJECTION

BARCO ULTRA REALITY 7000

R9002810

OWNER’S MANUAL

30062003 R5976455/02

Product revision

Software version: 1.10

Barco nv Intelligent Displays

Noordl

aan 5, 8520 Kuurne

Phone: +32 56.36.82.11

Fax: +32 56.35.86.51

E-mail:

[email protected]

Visit us at the web: www.barco.com

Printed in Belgium

Federal Communication Commission (FCC Statement)

This equipment has been tested and found to comply with the limits for a class A digital device, pursuant to Part 15 of the FCC rules.

These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial

environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with

the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area may

cause harmful interference, in which case the user will be responsible for correcting any interference.

Trademarks

Brand and product names mentioned in this manual may be trademarks, registered trademarks or copyrights of their respective holders.

All brand and product names mentioned in this manual serve as comments or examples and are not to be understood as adverti

sing for

the products or their manufactures.

Table of contents

TABLE OF CONTENTS

1. Packaging and Dimensions ...................................................................................... 3

1.1 Lens Packaging........................................................................................................................ 3

1.2 Dimensions............................................................................................................................. 3

2. Installation Guidelines............................................................................................. 5

2.1 Safety warnings........................................................................................................................ 5

2.2 Installation guidelines.................................................................................................................. 5

2.3 Projector configurations................................................................................................................ 6

2.4 Lenses.................................................................................................................................. 8

2.4.1 Lenses ........................................................................................................................... 9

2.4.2 Lens selection ................................................................................................................... 9

2.4.3 Lens formulas ................................................................................................................... 9

2.4.4 Lens installation . . ...............................................................................................................10

2.4.5 Cleaning the lens . ...............................................................................................................11

3. Connections.........................................................................................................13

3.1 Input Source connection ............................................................................................................... 13

3.1.1 Input facilities . ...................................................................................................................13

3.1.2 5-cable input (BNC1) . ...........................................................................................................13

3.1.3 5-cable data input (BNC2) ......................................................................................................14

3.1.4 Video input.......................................................................................................................14

3.1.5 S-Video input .................................................................................................................... 15

3.1.6 Digital Visual Interface (DVI) input . . ............................................................................................ 16

3.1.7 SDI input . . . . . . ...................................................................................................................17

3.1.8 HDSDI input ..................................................................................................................... 17

3.1.9 Communications.................................................................................................................18

3.1.9.1 RS232 IN connection.....................................................................................................18

4. Getting started......................................................................................................21

4.1 RCU & Local keypad...................................................................................................................21

4.2 Terminology overview..................................................................................................................21

4.3 Switching on............................................................................................................................ 23

4.4 Lamp runtime...........................................................................................................................24

4.5 Quick set up adjustments..............................................................................................................25

4.5.1 Quick lens Adjustment ..........................................................................................................25

4.5.2 Using the RCU................................................................................................................... 25

4.5.3 Projector address................................................................................................................27

4.5.3.1 Address setting ...........................................................................................................27

4.5.3.2 Displaying and Programming addresses into the RCU..................................................................28

4.5.4 Controlling the projector.........................................................................................................28

4.5.5 Using the menu..................................................................................................................29

4.5.6 Using the Dialogboxes . . . . . . ....................................................................................................30

5. Source Selection ...................................................................................................31

5.1 Source selection .......................................................................................................................31

5.2 Composite Video ......................................................................................................................32

5.3 S-Video selection ......................................................................................................................32

6. General Menu .......................................................................................................35

6.1 Pause...................................................................................................................................35

6.2 Freeze..................................................................................................................................35

6.3 Standby Timer..........................................................................................................................36

6.4 Identification............................................................................................................................37

6.5 Network Card reboot ...................................................................................................................38

6.6 Runtimes ............................................................................................................................... 38

6.7 History..................................................................................................................................39

6.8 Reset runtime ..........................................................................................................................40

6.9 Runtime warning.......................................................................................................................40

6.10Lamp Dimming.........................................................................................................................41

7. Image Menu .........................................................................................................43

7.1 Settings.................................................................................................................................43

7.1.1 Contrast.......................................................................................................................... 44

7.1.2 Brightness ....................................................................................................................... 44

7.1.3 Color ............................................................................................................................. 44

7.1.4 Tint (hue). . .. . . ...................................................................................................................44

7.1.5 Sharpness .......................................................................................................................45

7.1.6 Gamma ..........................................................................................................................45

7.1.7 Phase............................................................................................................................ 45

7.2 Aspect ratio............................................................................................................................. 45

7.3 Show native resolution.................................................................................................................46

7.4 Blanking ................................................................................................................................47

7.5 Keystone ...............................................................................................................................49

R5976455 BARCO ULTRA REALITY 7000 30062003

1

Table of contents

7.6 Color temperature......................................................................................................................49

7.7 Filmmode detection....................................................................................................................50

7.8 Advanced settings .....................................................................................................................51

7.8.1 Noise reduction .. ...............................................................................................................51

7.9 Input balance...........................................................................................................................52

7.10AGC on Video ......................................................................................................................... 52

7.11Manual Gain Control................................................................................................................... 52

8. Tools Menu ..........................................................................................................53

8.1 Introduction to PiP . . ................................................................................................................... 53

8.2 PiP select...............................................................................................................................55

8.3 PiP add window . . . . . ...................................................................................................................55

8.4 PiP remove window....................................................................................................................56

8.5 PiP layout...............................................................................................................................57

8.5.1 PiP Save......................................................................................................................... 57

8.5.2 PiP rename layout...............................................................................................................58

8.5.3 PiP delete layout ................................................................................................................58

8.6 PiP Adjust ..............................................................................................................................59

8.7 Diagnostics . . . ..........................................................................................................................60

9. Signal Menu .........................................................................................................63

9.1 Switching mode ........................................................................................................................63

9.2 Background . . ..........................................................................................................................63

10.Image files menu ...................................................................................................65

10.1Load file................................................................................................................................ 65

10.2Auto Image............................................................................................................................. 66

10.3Edit file .................................................................................................................................67

10.4Rename file . . .......................................................................................................................... 70

10.5Copy ...................................................................................................................................70

10.6Delete..................................................................................................................................71

11.Display setup........................................................................................................73

11.1Full screen representation.............................................................................................................73

11.2Startup screen .........................................................................................................................73

11.3Textbox.................................................................................................................................74

11.4Take screenshot .......................................................................................................................74

11.5Menu bar position......................................................................................................................75

11.6Status bar position.....................................................................................................................75

11.7Sliderbox position......................................................................................................................76

11.8AutoImage Setup ...................................................................................................................... 77

12.Installation menu...................................................................................................79

12.1Lens adjustments......................................................................................................................79

12.2Projector address . . . ................................................................................................................... 80

12.3Orientation .............................................................................................................................81

12.4Language ..............................................................................................................................82

12.5Quick access keys.....................................................................................................................82

12.6RS232 baudrate .......................................................................................................................83

12.7Network configuration .................................................................................................................83

12.8Change password . . ...................................................................................................................84

12.9Auto file load...........................................................................................................................85

A. Standard Image Files...............................................................................................87

A.1 Table overview .........................................................................................................................87

B. Cleaning the Dustfilter.............................................................................................91

B.1 Cleaning . . ..............................................................................................................................91

Glossary .................................................................................................................93

2 R5976455 BARCO ULTRA REALITY 7000 30062003

1. Packaging and Dimensions

1. PACKAGING AND DIMENSIONS

This chapter handles about the way the projector is packed and gives an overview of the dimensions.

• Lens Packaging

• Dimensions

1.1 Lens Packaging

Way of Packaging

Lenses are supplied as an individual item.

Theyarepackedinacartonbox.

Save the original shipping carton and packing material, they will be necessary if you ever have to transport

the lens.

Never transport the projector with the lens mounted on it !

Always remove the lens before transporting the projector.

1.2 Dimensions

Dimensions overview

Dimensions are given in mm (1 inch = 25.4 mm)

187.2

202.4

371

.

2

53.5

29.6

53.5

97.6

120.2

245.1

152.6

6

107.5

min 12

max

24

Image 1-1

R5976455 BARCO ULTRA REALITY 7000 30062003 3

1. Packaging and Dimensions

46 82.7 211.4

169.5

139.6

14

148.9

380.6

526.8

60

43

124.1

217.2

147.8

124.4

42

Image 1-2

184.4

368.7

Image 1-3

4 R5976455 BARCO ULTRA REALITY 7000 30062003

2. Installation Guidelines

2. INSTALLATION GUIDELINES

Overview

• Safety warnings

• Installation guidelines

• Projector configurations

• Lenses

2.1 Safety warnings

Before installing the projector, read first the safety instructions in the safety manual (R5975258) delivered with

the projector.

Insure that the projector is installed in an easy to evacuate room in case of a lamp explosion.

2.2 Installation guidelines

Ambient temperature check

Careful consideration of things such as image size, ambient light level, projector placement and type of screen to use are critical to

the optimum use of the projection system.

Max. ambient temperature : 40 °C or 104 °F

Min. ambient temperature : 0 °C or 32 °F

The projector will not operate if ambient air temperature falls outside this range (0°C- 40°C or 32°F-104°F).

Environment

Do not install the projection system in a site near heat sources such as radiators or air ducts, or in a place subject to direct sunlight,

excessive dust or humidity. Be aware that room heat rises to the ceiling; c

heck that temperature near the installation site is not

excessive

Harmful Environmental Contamination Precaution

Environment condition check

A projector must always be mounted in a manner which ensures the free flow of clean air into the projectors ventilation inlets as well

as free flow at the ventilation outlets. The installati

on must also allow easy access to the consumable parts ( dustfilters, lamps, ...)

For installations in environments where the projector is subject to airborne contaminants such as that produced by smoke machines

or similar (these deposit a thin layer of greasy residue upon the projectors internal optics and imaging electronic surfaces, degrading

performance), then it is highly advisable and desi

rable to have this contamination removed prior to it reaching the projectors clean

air supply. Devices or structures to extract or shield contaminated air well away from the projector are a prerequisite, if this is not

a feasible solution then measures to relocate the projector to a clean air environment should be considered. Make sure that the

projector never runs with dirty dustfilters as

this will dramatically reduce the lifetime of the consumables. It is advised to clean the

dustfilters on a regular basis and to replace them at any lamp change. Barco reserves itself the right to refuse warranty replacement

of consumables if they have been used in a projector with dirty airfilters. Only use the manufactures recommended cleaning kit which

has been specifically designed for clea

ning optical parts, never use industrial strength cleaners on a projectors optics as these will

degrade optical coatings and damage sensitive optoelectronics .

Failure to take suitable precautions to protect the projector from the effects of persistent and prolonged air contaminants will culmi-

nate in extensive and irreversible ingrained optical damage. At this stage cleaning of the internal optical units will be non-effective

and impracticable. Damage of this nature is under no circumstances covered under the manufactures warranty and may deem the

warranty null and void. In such a case the client shall be held solely responsible for all costs incurred during any repair. It is the

clients responsibility to ensure at all times that the projector is protected from the harmful effects of hostile airborne particles in the

environment of the projector. The manufacture reserves the right to refuse warranty repair if a projector has been subject to wantful

neglect, abandon or improper use.

What about ambient light ?

The ambient light level of any room is made up of direct or indirect sunlight and the light fixtures in the room. The amount of ambient

light will determine how brig

ht the image will appear. So, avoid direct light on the screen. Windows that face the screen should be

R5976455 BARCO ULTRA REALITY 7000 30062003

5

2. Installation Guidelines

covered by opaque drapery while the set is being viewed. It is desirable to install the projection system in a room whose walls and

floor are of non-reflecting material. The use of recessed ceiling lights and a method of dimming those lights to an acceptable level

is also important. Too much ambient light will ‘wash out’ of the projected image. This appears as less contrast between the darkest

and lightest parts of the image. With bigger screens, the ‘wash out’ becomes more important. As a general rule, darken the room to

the point where there is just sufficient light to read or write comfortably. Spot lighting is desirable for illuminating small areas so that

interference with the screen is minimal.

Which screen type ?

There are two major categories of screens used for projection equipment. Those used for front projected images and those for rear

projection applications. Screens are rated by how much light they reflect (or transmit in the case of rear projection systems) given a

determined amount of light projected toward them. The ‘GAIN’ of a screen is the term used. Front and rear screens are both rated

in terms of gain. The gain of screens range from a white matte screen with a gain of 1 (x1) to a brushed aluminized screen with a

gain of 10 (x10) or more. The choice between higher and lower gain screens is largely a matter of personal preference and another

consideration called the Viewing angle. In considering the type of screen to choose, determine where the viewers will be located

and go for the highest gain screen possible. A high gain screen will provide a brighter picture but reduce the viewing angle. For

more information about screens, contact your local screen supplier.

Image size

The projector is designed for projecting an image size with a screenwidth from 1.00m (3.3ft) to 6.00m (19.7ft) with an aspect ratio of

4to3.

2.3 Projector configurations

The different configurations

1. Rear/Ceiling

2. Rear/Table

3. Front/Ceiling

4. Front/Table

6

R5976455 BARCO ULTRA REALITY 7000 30062003

2. Installation Guidelines

Positioning the projector

P

PD

x

F

a

b

c

S

B

SH

SW

SH

SW

F

CD=SH/2+B-A

A

Image 2-1

R5976455 BARCO ULTRA REALITY 7000 30062003 7

2. Installation Guidelines

a

b

c

SH

SW

F

PD

x

F

S

B

SH

SW

CD=B-A

A

Image 2-2

2.4 Lenses

Overview

• Lenses

• Lens selection

• Lens formulas

• Lens installation

• Cleaning the lens

8

R5976455 BARCO ULTRA REALITY 7000 30062003

2. Installation Guidelines

2.4.1 Lenses

Available lenses

The following lenses are available, or will become available (contact a BARCO service center) as an option :

Lenses

Standard version

QFD(1.27:1)

R9840400

QFD(2.5:1)

R9840290

QFD(1.4-2.1:1)

R9840380

QFD(2.1-3.0:1)

R9840390

QFD(3.5-4.5:1)

R9840060

QFD(4.5-6.0:1)

R9840100

QFD(7:1)

R9840410

QGD (0.8:1) / SW: (1–1.4)m

R9829800

QGD (0.8:1) / SW: (1.7–2.4)m

R9840040

QGD(0.86:1)

R9840491

2.4.2 Lens selection

How to select ?

1. Determine the required screen width.

2. Determine the approximate position of the projector in the projection room with regard to the screen and measure the projector-

screen distance (PD).

3. Use the lens formulas to find the best corresponding PD with regard to the measured projector-screen distance for the required

screen width.

2.4.3 Lens formulas

Formulas

Lenses

Metric Formulas (meter) Inch Formulas (inch)

QFD(1.27:1) PD = 1.29 x SW — 0,0195 + 0,00276 /

SW

PD = 1.29 x SW — 0.768 + 4.278 / SW

QFD(2.5:1) PD = 2.427 x SW + 0,025 + 0,022 / SW PD = 2.427 x SW +0.984 + 34.10 / SW

QFD(1.4-2.1:1) PD

min

= 1,44 x SW + 0,0287 — 0,022 /

SW

PD

max

= 2,20 x SW — 0,01 + 0,020 / SW

PD

min

= 1.44 x SW + 1.13 — 34.10 / SW

PD

max

= 2.20 x SW — 0.39 + 31.00 / SW

QFD(2.1-3.0:1) PD

min

= 2,13 x SW — 0,10 + 0,056 / SW

PD

max

= 2,90 x SW + 0,10 — 0,0745 /

SW

PD

min

=2.13xSW—3.937+86.80/

SW

PD

max

= 2.90 x SW + 3.937 — 115.48 /

SW

QFD(3.4-4.5:1) PD

min

= 3,374 x SW — 0,115 + 0,0575 /

SW

PD

max

= 4,433 x SW — 0,133 + 0,0556

/SW

PD

min

= 3.374 x SW — 4.53 + 89.13 /

SW

PD

max

= 4.433 x SW — 5.24 + 86.18 /

SW

QFD(4.5-6.0:1) PD

min

= 4,29 x SW — 0,02 + 0,0009

/

SW

PD

max

= 5,86 x SW + 0,15 + 0,0121 /

SW

PD

min

= 4.29 x SW — 0.787 + 1.395

/

SW

PD

max

= 5.86 x SW + 5.906 + 18.755 /

SW

QFD(7.0:1) PD = 6,882 x SW — 0,045 + 0,048 / SW PD = 6.882 x SW — 1.772 + 74.4 / SW

R5976455 BARCO ULTRA REALITY 7000 30062003 9

2. Installation Guidelines

Lenses

Metric Formulas (meter) Inch Formulas (inch)

QGD(0.8:1) / SW: (1-1.4)m PD = 0,775 x SW — 0,048 + 0,0074 /

SW

PD = 0.775 x SW — 1.89 + 11.47 / SW

QGD(0.8:1) / SW: (1.7-2.4)m PD = 0,775 x SW — 0,048 + 0,0072 /

SW

PD = 0.775 x SW — 1.89 + 11.47 / SW

QGD(0.86:1) PD = 0,8376 x SW + 0,00254 — 0,0150

/SW

PD = 0.8376 x SW + 0.1 — 23.25 / SW

Lens program to calculate the projector distance

is available on the BARCO web site :

h

ttp://www.barco.com/projection_systems/customer_services/lens_program.asp

2.4.4 Lens installation

How to install ?

Follow the next procedure :

1. Open the lens cover of the projector by pivoting it up and take it off. (image 2-3)

2. Pull the lens locks levers backwards t

o open the lens locks. (image 2-4)

3. Put the lens on the lens holder. (image 2-5)

4. Push the lens locks back in position and lock the levers.

5. Plug the wires of the motor unit into the connector (image 2-6)

6. Re-install the lens cover.

Image 2-3

Image 2-4

Ima

ge 2-5

Image 2-6

10 R5976455 BARCO ULTRA REALITY 7000 30062003

2. Installation Guidelines

The procedure for the mounting of a Scheimpflug lens is different.

Refer to the installation manual of the lens.

Never transport the projector with the lens mounted on it !

Always remove the lens before transporting the projector.

2.4.5 Cleaning the lens

To minimize the possibility of damaging the optical coating or scratching exposed lens surface, we have de-

veloped recommendations for cleaning the lens. FIRST, we recommend you try to remove any material from

the lens by blowing it off with clean, dry deionized air. DO NOT use any liquid to clean the lenses.

Necessary tools

Tor a ys ee

TM

cloth (delivered together with the lens kit). Order number : R379058.

Howtocleanthelens?

Proceed as follow :

1. Always wipe lenses with a CLEAN Toraysee

TM

cloth.

2. Always wipe lenses in a single direction.

Warning: Do not wipe back and forwards across the lens surface as this tends to grind dirt into the coating.

3. Do not leave cleaning cloth in either an open room or lab coat pocket, as doing so can contaminate the cloth.

4. If smears occur when cleaning lenses, replace the cloth. Smears are the first indication of a

dirty cloth.

Do not use fabric softener when washing the cleaning cloth or softener sheets whe

n drying the cloth.

Do not use liquid cleaners on the cloth as doing so will contaminate the cloth.

Other lenses can also be cleaned safely with this Toraysee

TM

cloth.

R5976455 BARCO ULTRA REALITY 7000 30062003 11

2. Installation Guidelines

12 R5976455 BARCO ULTRA REALITY 7000 30062003

3. Connections

3. CONNECTIONS

Overview

• Input Source connection

3.1 Input Source connection

3.1.1 Input facilities

Overview input facilities

• 5-cable input (BNC1)

• 5-cable Data input (BNC2)

• Composite Video

•S-Video

• SDI: Serial Digital Interface (I/O)

• DVI : Digital Visual Interface

• HDSDI: High Definition SDI

3.1.2 5-cable input (BNC1)

Wheretofind?

Slot 1 has 5 BNC input terminals, located as shown on the image.

SDI

SDO

S-VIDEO

VIDEO

R

GB

V

7

2

43

10Base-T

G/Y B/PB H/C

V

1

HDSDI

HDSDO

9

RS 232 IN

RS 232 OUT

RC

DVI

H/C

R/PR

95

Image 3-1

Which signals can be connected to the 5 cable input.

The following signals can be connected to these BNC connectors :

Connector name

R

G

B H V

RGBHV

R

G

B H V

RGBS

R

G

B

S

-

RG

S

B

R

G

S

B

- -

Composite video

-

Video

- - -

R5976455 BARCO ULTRA REALITY 7000 30062003 13

3. Connections

Connector name

R

G

B H V

Super Video

-

Y

- -

C

Component Video - SS

R-Y Y B-Y

S

-

Component Video - SOY

R-Y Y

S

B-Y

- -

How to select slot 1

1. Press key 1 on the RCU or the local keypad or use the menu

The selection of a composite video connected to the 5 cable input happens by pressing “3”, the composite

video configuration has to be done in the source selection menu.

3.1.3 5-cable data input (BNC2)

What can be connected ?

The following signals can be connected to these BNC connectors :

Connector name

R

G

B H V

RGBHV

R

G

B H V

RGBS

R

G

B

S

-

RG

S

B

R

G

S

B

- -

How to connect a computer to the input?

1. Connect the output of the graphical card of the computer to the Computer input of the projector (image 3-2)

SDI

SDO

S-VIDEO

VIDEO

R

GB

V

7

2

43

10Base-T

G/Y B/PB H/C

V

1

HDSDI

HDSDO

9

RS 232 IN

RS 232 OUT

RC

DVI

H/C

R/PR

95

Image 3-2

How to select slot 2

1. Press key 2 on the RCU or the local keypad or use the menu

3.1.4 Video input

Video

Composite Video is a single video signal that contains luminance, color and synchronization information. NTSC, PAL

and SECAM are examples of composite video systems.

14 R5976455 BARCO ULTRA REALITY 7000 30062003

3. Connections

What can be connected to the Video input?

Composite video signals from a VCR, OFF air signal decoder, etc... No loop through.

How to connect a Video source.

1. Connect the video output of your source to the video input of the projector (slot 3). 1 x BNC or cinch 1.0Vpp ± 3 dB. (image 3-3)

Note: No loop through ava ilable.

SDI

SDO

S-VIDEO

VIDEO

R

GB

V

7

2

43

10Base-T

G/Y B/PB H/C

V

1

HDSDI

HDSDO

9

RS 232 IN

RS 232 OUT

RC

DVI

H/C

R/PR

95

Image 3-3

How to select slot 3

1. Key in 3 on the RCU or the local keypad or use the menu

The cinch connector and the BNC connector are internaly connected together.

A video signal can also be connected on the 5 cable input (BNC1)

3.1.5 S-Video input

What can be connected?

Separate Y-luma/C-chroma signals for higher quality playback of Super VHS-signals.

How to connect the S-Video signal.

1. Connect the S-video output of your source to the S-video input of the projector (slot 4)

Pin configuration of the mini DIN plug.

1 ground luminance

2 ground chrominance

3 luminance 1.0Vpp ± 3dB

4 chrominance 282 mVpp ± 3dB

How to select slot 4?

1. Key in 4 on the RCU or the local keypad or use the menu (image 3-4)

R5976455 BARCO ULTRA REALITY 7000 30062003

15

3. Connections

SDI

SDO

S-VIDEO

VIDEO

R

GB

V

7

2

43

10Base-T

G/Y B/PB H/C

V

1

HDSDI

HDSDO

9

RS 232 IN

RS 232 OUT

RC

DVI

H/C

R/PR

95

Image 3-4

3.1.6 Digital Visual Interface (DVI) input

DVI

Digital Visual Interface is a display interface developed in response to the proliferation of digital flat panel displays. It

uses a high speed serial interface with TMDS (Transition Minimized d

ifferential signalling) to send data to the display.

DVI can be single or dual link.

Input specifications

Single link DVI

Differential input voltage: 200 mV - 800mV

SDI

SDO

S-VIDEO

VIDEO

R

GB

V

7

2

43

10Base-T

G/Y B/PB H/C

V

1

HDSDI

HDSDO

9

RS 232 IN

RS 232 OUT

RC

DVI

H/C

R/PR

95

Image 3-5

DVI-I type connector analog link (4 pins at the right side of the connector) not supported

How to select the DVI Input ?

1. Press 5 on the RCU or the locol keypad or use the menu

16

R5976455 BARCO ULTRA REALITY 7000 30062003

Page is loading ...

Barco ULTRA REALITY 7000 R9002810 User manual

This manual is also suitable for

Barco ULTRA REALITY 7000 R9002810 User manual

Related papers

Other documents