Canon 7215 - LV XGA LCD Projector User manual

Category
Projectors
Type
User manual
E
English
Multimedia Projector
Owner’s Manual
LV-7215 LV-7210 LV-5210
2
Table of Contents
TRADEMARKS
Apple, Macintosh, and PowerBook are trademarks or registered trademarks of Apple Computer,Inc.
IBM, VGA, XGA, and PS/2 are trademarks or registered trademarks of International Business Machines, Inc.
Windows and PowerPoint are registered trademarks of Microsoft Corporation.
Each name of corporations or products in the owner's manual is a trademark or a registered trademark of its respective
corporation.
Features and Design 8
Basic Operation 19
Computer Input 24
Video Input 32
Setting 38
Appendix 45
Part Names and Functions 9
Front 9
Back 9
Bottom 9
Terminal 10
Top 11
Remote Control Unit 12
Laser Pointer Function 13
Pointer Function 13
Remote Control Code 14
Wireless Mouse Operation 14
Remote Control Operating Range 15
Remote Control Batteries Installation 15
Installation 16
Positioning the Projector 16
Adjustable Feet 16
Connecting to a Computer 17
Connecting to Video Equipment 18
Turning On the Projector 19
Turning Off the Projector 19
Zoom Adjustment 20
Focus Adjustment 20
Keystone Adjustment 20
Picture Freeze Function 20
No Show Function 21
P-Timer Function 21
Sound Adjustment 21
On-Screen Menu 22
Menu Bar 23
Input Source Selection 24
Computer System Selection 25
Computer Adjustment (Auto) 26
Computer Adjustment (Manual) 27
Image Level Selection 29
Image Level Adjustment 30
Screen Size Adjustment 31
Input Source Selection (Video, S-Video) 32
Input Source Selection (Component, RGB Scart 21-Pin) 33
Video System Selection 34
Image Level Selection 35
Image Level Adjustment 36
Screen Size Adjustment 37
Setting 38
Troubleshooting 45
Indicators and Projector Condition 47
Menu Tree 48
Compatible Computer Specifications 50
Technical Specifications 51
Configurations of Terminals 52
Optional Parts 53
Attaching the Lens Cover 54
Table of Contents 2
To the Owner 3
Safety Instructions 4
Compliance 6
Installing the Projector in Proper Position 5
Air Circulation 5
Moving the Projector 5
Connecting the AC Power Cord 7
Maintenance and Cleaning 41
Warning Indicator 41
Cleaning the Air Filters 42
Cleaning the Projection Lens 42
Cleaning the Projector Cabinet 42
Lamp Replacement 43
Lamp Replace Counter 44
3
To the Owner
CAUTION : TO REDUCE THE RISK OF ELECTRIC
SHOCK, DO NOT REMOVE COVER (OR
BACK). NO USER-SERVICEABLE PARTS
INSIDE EXCEPT LAMP REPLACEMENT.
REFER SERVICING TO QUALIFIED
SERVICE PERSONNEL.
THIS SYMBOL INDICATES THAT DANGEROUS
VOLTAGE CONSTITUTING A RISK OF ELECTRIC
SHOCK IS PRESENT WITHIN THIS UNIT.
THIS SYMBOL INDICATES THAT THERE ARE
IMPORTANT OPERATING AND MAINTENANCE
INSTRUCTIONS IN THE OWNER'S MANUAL WITH
THIS UNIT.
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
Before operating this projector, read this manual thoroughly
and operate the projector properly.
This projector provides many convenient features and
functions. Operating the projector properly enables you to
manage those features and maintains it in better condition for
a considerable time.
Improper operation may result in not only shortening the
product-life, but also malfunctions, fire hazard, or other
accidents.
If your projector seems to operate improperly, read this
manual again, check operations and cable connections and try
the solutions in the “Troubleshooting” section in the end of
this booklet. If the problem still persists, contact the dealer
where you purchased the projector or the service center.
Safety Precaution
WARNING : TO REDUCE THE RISK OF FIRE OR ELECTRIC
SHOCK, DO NOT EXPOSE THIS APPLIANCE
TO RAIN OR MOISTURE.
This projector produces intense light from the projection
lens. Do not stare directly into the lens as possible. Eye
damage could result. Be especially careful that children do
not stare directly into the beam.
Install the projector in a proper position. If not, it may
result in a fire hazard.
Provide appropriate space on the top, sides and rear of the
projector cabinet for allowing air circulation and cooling the
projector. Minimum clearance must be maintained. If the
projector is to be built into a compartment or similarly
enclosed, the minimum distances must be maintained. Do
not cover the ventilation slot on the projector. Heat build-
up can reduce the service life of your projector, and can
also be dangerous.
– The remote control, supplied to this projector, emits the
laser beam as the Laser pointer function from laser light
window while pressing the LASER button (for 1 minute /
Signal Emission indicator lights red to indicate laser
emission). Do not look into the laser light window or shine
the laser beam on a mirror, yourself or other people. Eye
damage may result.
Do not put any flammable object or spray can near the
projector, hot air is exhausted from the ventilation holes.
If the projector is not to be used for an extended time,
unplug the projector from the power outlet.
READ AND KEEP THIS OWNER'S MANUAL FOR LATER
USE.
SIDE and TOP REAR
4
Safety Instructions
All the safety and operating instructions should be read before
the product is operated.
Read all of the instructions given here and retain them for later
use. Unplug this projector from AC power supply before
cleaning. Do not use liquid or aerosol cleaners. Use a damp
cloth for cleaning.
Follow all warnings and instructions marked on the projector.
For added protection to the projector during a lightning storm,
or when it is left unattended and unused for long periods of
time, unplug it from the wall outlet. This will prevent damage
due to lightning and power line surges.
Do not expose this unit to rain or use near water... for
example, in a wet basement, near a swimming pool, etc...
Do not use attachments not recommended by the
manufacturer as they may cause hazards.
Do not place this projector on an unstable cart, stand, or table.
The projector may fall, causing serious injury to a child or
adult, and serious damage to the projector. Use only with a
cart or stand recommended by the manufacturer, or sold with
the projector. Wall or shelf mounting should follow the
manufacturer's instructions, and should use a mounting kit
approved by the manufacturers.
An appliance and cart combination should
be moved with care. Quick stops,
excessive force, and uneven surfaces
may cause the appliance and cart
combination to overturn.
Slots and openings in the back and bottom of the cabinet are
provided for ventilation, to insure reliable operation of the
equipment and to protect it from overheating.
The openings should never be covered with cloth or other
materials, and the bottom opening should not be blocked by
placing the projector on a bed, sofa, rug, or other similar
surface. This projector should never be placed near or over a
radiator or heat register.
This projector should not be placed in a built-in installation
such as a book case unless proper ventilation is provided.
Never push objects of any kind into this projector through
cabinet slots as they may touch dangerous voltage points or
short out parts that could result in a fire or electric shock.
Never spill liquid of any kind on the projector.
Do not install the projector near the ventilation duct of air-
conditioning equipment.
This projector should be operated only from the type of power
source indicated on the marking label. If you are not sure of
the type of power supplied, consult your authorized dealer or
local power company.
Do not overload wall outlets and extension cords as this can
result in fire or electric shock. Do not allow anything to rest
on the power cord. Do not locate this projector where the
cord may be damaged by persons walking on it.
Do not attempt to service this projector yourself as opening or
removing covers may expose you to dangerous voltage or
other hazards. Refer all servicing to qualified service
personnel.
Unplug this projector from wall outlet and refer servicing to
qualified service personnel under the following conditions:
a. When the power cord or plug is damaged or frayed.
b. If liquid has been spilled into the projector.
c. If the projector has been exposed to rain or water.
d. If the projector does not operate normally by following the
operating instructions. Adjust only those controls that are
covered by the operating instructions as improper
adjustment of other controls may result in damage and will
often require extensive work by a qualified technician to
restore the projector to normal operation.
e. If the projector has been dropped or the cabinet has been
damaged.
f. When the projector exhibits a distinct change in
performance-this indicates a need for service.
When replacement parts are required, be sure the service
technician has used replacement parts specified by the
manufacturer that have the same characteristics as the
original part. Unauthorized substitutions may result in fire,
electric shock, or injury to persons.
Upon completion of any service or repairs to this projector,
ask the service technician to perform routine safety checks to
determine that the projector is in safe operating condition.
Bij dit product zijn batterijen
geleverd.
Wanneer deze leeg zijn, moet
u ze niet weggooien maar
inleveren als KCA.
NL
For Use in Netherlands
5
Safety Instructions
Installing the Projector in Proper Position
USE CAUTION WHEN CARRYING OR TRANSPORTING THE PROJECTOR
Do not drop or bump the projector, otherwise damage or malfunction may result.
When carrying the projector, use a suitable carrying case.
Do not transport the projector by using a courier or transport service in an unsuitable transport case. This may cause
damage to the projector. To transport the projector through a courier or transport service, consult your dealer for their
information.
Moving the Projector
When moving the projector, replace the lens cover and retract the adjustable feet to prevent damage to the lens and
cabinet. When the projector is not in use for an extended period, put it into the carrying bag supplied with the projector.
The carrying bag is intended for protection from dust and scratches on the surface of a cabinet, and it is not designed to
protect the projector from external forces. Do not transport the projector through a courier or transport services with this
bag. The projector can be damaged. When handling the projector, do not drop, bump, subject it to strong forces or put
other things on the cabinet.
Install the projector properly. Improper installation may reduce the lamp life and cause a fire hazard.
20˚
20˚
Do not tilt the projector more than
20 degrees above and below.
Do not point the projector up to
project an image.
Do not point the projector down
to project an image.
Do not put the projector on either
side to project an image.
Air Circulation
Openings in the cabinet are provided for ventilation and to ensure reliable operation of
the product and to protect it from overheating, and these openings must not be
blocked or covered.
CAUTION
Hot air is exhausted from the exhaust vent. When using or installing the projector,
the following precautions should be taken.
Do not put any flammable objects near the vent.
Keep the exhaust vent at least 3’(1m) away from any objects.
Do not touch a peripheral part of the exhaust vent, especially screws and metallic
part. This area will become hot while the projector is being used.
Do not put anything on the cabinet. The materials put on the cabinet will not only
get damaged but also cause fire hazard by heat.
Cooling fans are provided to cool down the projector. This projector monitors internal
temperature and control the running speed of the cooling fans.
Air Intake Vent
Air Intake VentExhaust Vent
(Hot air exhaust)
6
Compliance
The AC Power Cord supplied with this projector meets the requirement for use in the country you purchased it.
AC Power Cord for the United States and Canada :
AC Power Cord used in the United States and Canada is listed by the Underwriters Laboratories
(UL) and certified by the Canadian Standard Association (CSA).
AC Power Cord has a grounding-type AC line plug. This is a safety feature to be sure that the plug
will fit into the power outlet. Do not try to defeat this safety feature. Should you be unable to
insert the plug into the outlet, contact your electrician.
GROUND
THE SOCKET-OUTLET SHOULD BE INSTALLED NEAR THE EQUIPMENT AND EASILY ACCESSIBLE.
AC POWER CORD REQUIREMENT
Federal Communication Commission Notice
Multimedia Projector, Model : LV-7215, LV-7210, LV-5210
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that may cause undesired operation.
Note : This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of
the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential
installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee
that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures :
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.
Use of shielded cable is required to comply with class B limits in Subpart B of Part 15 of FCC Rules.
Do not make any changes or modifications to the equipment unless otherwise specified in the instructions. If such changes or
modifications should be made, you could be required to stop operation of the equipment.
Canon U.S.A., Inc.
One Canon Plaza, Lake Success, NY 11042, U.S.A.
Tel No. (516)328-5600
For use in Germany
This product is intended for use in residential, commercial and light industry environment.
Canadian Radio Interference Regulations
This Class B digital apparatus meets all requirements of the Canadian Interference-Causing Equipment
Regulations.
7
Compliance
Connecting the AC Power Cord
To the POWER CORD
CONNECTOR on the
projector.
Projector side AC Outlet side
Ground
NOTE ON THE POWER CORD
The AC Power Cord must meet the requirements of the country where you use the projector.
Confirm the AC plug type with the chart below. The proper AC power cord must be used.
If the supplied AC Power Cord does not match the AC outlet, contact your sales dealer.
To the AC Outlet.
(120 V AC)
For Continental Europe
For the U.S.A. and Canada
To the AC Outlet.
(200 - 240 V AC)
This projector uses nominal input voltages of 100-120 V or 200-240
V AC. This projector automatically selects the correct input
voltage. It is designed to work with single-phase power systems
having a grounded neutral conductor. To reduce risk of electrical
shock, do not plug into any other type of power system.
Consult your authorized dealer or service station if you are not sure
of the type of power being supplied.
Connect the projector with all peripheral equipment before turning
the projector on. (See page 17-18 for connection.)
CAUTION
For safety, unplug AC power cord when the projector is not in
use.
When this projector is connected to an outlet with AC power
cord, it is in Stand-by mode and consumes a little electric
power.
Connect AC power cord (supplied) to the projector.
The AC outlet must be near this equipment and must
be easily accessible.
8
Features and Design
This Multimedia Projector is designed with the most advanced technology for portability, durability, and ease of use. This
projector utilizes built-in multimedia features, a palette of 16.77 million colors, and matrix liquid crystal display (LCD)
technology.
Compatibility
The projector widely accepts various video and
computer input signals including;
Computers
IBM-compatible or Macintosh computer up to
1280 x 1024 resolution.
6 Color Systems
NTSC, PAL, SECAM, NTSC 4.43, PAL-M or PAL-N
color system can be connected.
Component Video
Component video signal, such as a DVD player
output high definition TV signals including 480i,
480p, 575i, 575p, 720p, 1035i or 1080i, can be
connected.
S-Video
S-Video signal, such as a S-VHS VCR output
signal, can be connected.
RGB Scart
RGB Scart signal can be connected.
Simple Computer System Setting
The projector has the Multi-scan system to conform to
almost all computer output signals quickly. (See page
25.)
Compact Design
This projector is extremely compact in size and weight. It is
designed to be carried and work anywhere you wish to use.
Keystone Adjustment
Keystone distortion can be corrected vertically and
horizontally. The keystone correction function provides
you with additional flexibility. (See page 20 and 38.)
Multilanguage Menu Display
Operation menu is available in; English, German, French,
Italian, Spanish, Portuguese, Dutch, Swedish, Russian,
Chinese, Korean, or Japanese. (See page 38.)
Digital Zoom (for Computer)
The digital zoom function expands (to approx. 16 times
of screen size) or compress the image size, allowing you
to focus on crucial information at a presentation. (See
page 31.)
Wireless Mouse
The remote control unit supplied with this projector has
wireless mouse function for a connected computer.
This function enables you to operate both the projector
and the connected computer with the remote control
unit. (See page 14.)
Power Management
The Power management function reduces power
consumption and maintain the lamp life. (See page 39.)
Digital Visual Interface
The projector is equipped with DVI 29-pin terminal for
connecting DVI output from a computer or video
equipment. You can also enjoy digital entertainment
content protected by HDCP technology. (See page 24
for HDCP.)
Switchable Interface Terminal
The projector provides a switchable Interface terminal.
You can use the terminal as computer input or monitor
output conveniently. (See page 39.)
Pointer Function
The projector has a convenient function which displays
Spotlight or Pointer controlled by the remote control on a
projected image. The remote control also has the Laser
pointer function. These functions will make your
important presentation more effective. (See page 13,
40.)
Interlace Progressive Conversion
High-quality picture is available with this technology
which converts an interlace signal to a progressive
signal. (See page 36.)
Users Logo
A projected image can be captured and used for the
starting display of the projector with the Capture
function. You can also display the captured image in an
interval during your presentation instead of blackout
image with the No show function. (See page 21, 38.)
Multi Card Imager (optional)
The projector can be operated through wired/wireless
LAN by attaching the Multi Card Imager that is optionally
supplied. The Multi Card Imager is also used to view
digital images. It may be purchased at your Canon
authorized projector dealer.
Lamp Mode
Brightness of the projection lamp can be changed by
setting. The projector has the function to adjust the
brightness according to an input signal for the best
suited image. (See page 40.)
Wide Zoom Lens
This projector is equipped with Wide Zoom Lens which
is 1.6 times the zoom ratio, and it allows you to enjoy
100" screen size in range of 8.2' (2.5m) to 13.1' (4m).
9
Part Names and Functions
Back
Front
q Focus Ring
w Speaker
e Power Cord Connector
r Infrared Remote Receiver
t Zoom Lever
y Projection Lens
u Lens Cover (See page 54 for attaching.)
i Air Intake Vent
q w
e r t
q Exhaust Vent
q w e r
w Top Controls and Indicators
e Air Intake Vent
r Terminals and Connectors
CAUTION
Hot air is exhausted from the exhaust
vent. Do not put heat-sensitive
objects near this side.
q Air Intake Vent
w Air Filter
e Adjustable Feet
r Lamp Cover
Bottom
e
r
y u i
wq
q
10
Part Names and Functions
A built-in micro processor which controls this unit may rarely malfunction
and need to be reset. This can be done by pressing the RESET button
with a pen, which will shut down and restart the unit. Do not use the
RESET function excessively.
*
AUDIO
R IN L
VIDEO IN
DVI-I/
RGB IN-1
SERVICE PORT
S-VIDEO IN
COMPUTER
AUDIO IN
AUDIO OUT
RGB IN-2/
COMPONENT IN/
RGB OUT
RESET
MCI
q DVI-I / RGB IN-1
Connect computer output (Digital/Analog DVI-I type) or Multi
Card Imager (optional) to this terminal. (p17)
Terminal
q w e r t y
u i o
i S-VIDEO IN
Connect the S-VIDEO output from video equipment to this jack.
(p18)
e AUDIO IN
Connect the audio output from video equipment connected to
r or i to this jack. (When the audio output is monaural,
connect it to L (MONO) jack.) (p18)
y COMPUTER AUDIO IN
Connect the audio output (stereo) from a computer or video
equipment connected to q or u to this jack. (p 17, 18)
r
VIDEO IN
Connect the composite video output from video equipment to
VIDEO IN jack. (p18)
u RGB IN-2 /COMPONENT IN / RGB OUT
This terminal is switchable and can be used as computer input ,
component input, RGB Scart 21-Pin Video input, or monitor
output. Set the terminal up as either Computer input or
Monitor output properly before using this terminal. An optional
cable is required when using this terminal as component input
or RGB Scart 21-Pin Video input. (p17,18)
(This terminal outputs analog signal from DVI-I IN / RGB IN-1
terminal only when using as Monitor out.)
o AUDIO OUT
Connect an external audio amplifier to this jack. (p17, 18)
This terminal outputs sound from AUDIO IN terminal (e or y).
t USB (Series B)
When operating the connected computer with the remote
control unit, connect USB port of your computer to this
connector with a USB cable. (p17)
w SERVICE PORT
This jack is used to service this projector.
*
Do not press this button. This button is used for optional
accessories.
11
Part Names and Functions
INPUT
WARNING
LAMP REPLACE
MENU
POWER
KEY
STONE
SET
VOL
VOL
+
-
This projector has control buttons and indicators on its top.
To p
q w
r
t y u i
u LAMP REPLACE indicator
Turns yellow when the life of the projection lamp draws to an
end. (p43)
i WARNING indicator
Lights red when the projector detects abnormal condition. This
also flashes red when the internal temperature of the projector
exceeds the operating range. (p41)
r POWER ONOFF button
Turns the projector on or off. (p19)
POWER indicator
Flashes red until the projector gets ready to be turned on. It
turns red when the projector is in the stand-by mode. It
remains green while the projector is under operation.
t INPUT button
Selects input source. (p24, 32 )
q MENU button
Opens or closes the On-Screen Menu. (p22)
y POINT (Up/Down/Left/Right ) button
Selects an item or adjusts value in the On-Screen Menu. These
are also used to pan the image in the Digital zoom +/– mode.
(p31)
Point Left/Right buttons are used as VOL +/– button. (p21)
w SET button
Executes the item selected. It is also used to expand /
compress the image in Digital zoom +/– mode. (p31)
e KEYSTONE button
Corrects keystone distortion. (p20, 38)
e
12
Part Names and Functions
Remote Control Unit
q
w
e
r
t
y
u
i
o
!0
!1
!4
!5
!6
!7
!8
!9
@0
!2
!3
@1
@1 RESET/ON/ALL-OFF switch
When using the remote control, set this switch to “ON.” Set it to “ALL OFF” when
it is not used for energy saving. Slide this switch to the "RESET" to initialize the
remote control code. (p14)
w SIGNAL EMISSION indicator
The indicator lights red while the laser beam is being emitted from the Laser Light
Window or a signal is being sent from the remote control to the projector.
r AUTO PC button
Operates the Auto PC adjustment function. (p26)
!7 D.ZOOM button
Selects the Digital zoom +/– mode and resize the image. (p31)
!3 M
UTE button
Mutes sound. (p21)
y POINT (UP/DOWN/LEFT/RIGHT) button
Selects an item or adjusts value in the On-Screen Menu. These are also used to pan
the image in the Digital zoom +/- mode. (p31)
Point Left/Right button is also used as VOL +/- button. (p21)
!6 MENU button
Opens or closes the On-Screen Menu. (p22)
!0 LASER button
Operates the Laser pointer function. Laser beam is emitted while pressing this
button within 1 minute. When using this laser pointer for more than 1 minute,
release the LASER button and press it again. This button is also used as a
switching button to activate the Pointer function of the projector. (p13)
!4 POWER ON-OFF button
Turns the projector on or off. (p19)
!8 NO SHOW button
Turns the picture into black image. (p21)
!1 FREEZE button
Freezes the projected picture. (p20)
!2 IMAGE button
Selects image levels.(p29, 35)
i SET button
Executes the item selected, or to expand or compress image in the Digital zoom +/-
mode. (p31)
t COMPUTER button
Selects input source (COMPUTER 1 or COMPUTER 2). (p24)
@0
P-TIMER button
Operates P-Timer function. (p21)
o PAGE UP/DOWN button
Turns pages; the Up button to the previous page and the Down button to the next
page for an image from a computer. This function can be used to scroll pages in a
presentation. Connect the projector and your computer with a USB cable before
use. (See page 17.)
!9 R-CLICK button
Acts as right click for wireless mouse operation. (p14)
q L-CLICK button
Acts as left click for wireless mouse operation. (p14)
!5 VIDEO button
Selects input source (VIDEO). (p32)
e KEYSTONE button
Corrects keystone distortion. (p20, 38)
u PRESENTATION POINTER button
Move a pointer of the projector or a pointer for wireless mouse operation. (p13, 14)
13
Part Names and Functions
You can move Spotlight or Pointer of the projector with the remote control unit to emphasize a part of the projected image.
(See “Pointer” on page 40 for changing the patterns and sizes.)
While pressing the MENU button, hold down the NO SHOW
button for more than 7 seconds so that the Pointer function
can be available. (The Laser pointer function has switched to
the Pointer function.)
1
Spotlight
Press the LASER button on the remote control unit toward
the projector and see if the LASER button lights green, and
Spotlight or Pointer is displayed on the screen. Then you can
move Spotlight or Pointer with the PRESENTATION
POINTER button. If the LASER button does not light green
and still emits a laser beam, the Laser pointer function has
not switched to the Pointer function yet. Try these steps
until the LASER button lights green.
2
Pointer Function
To clear the Spotlight or Pointer displayed on the screen,
press the LASER button toward the projector and see if the
LASER button turns off.
To use the Laser pointer function once again, while pressing
the MENU button, hold down the NO SHOW button for
more than 7 seconds.
3
After the Laser pointer function has
switched to the Pointer function, the
LASER button is used as the Pointer
function ON-OFF switch instead of the
Laser pointer function.
Press the LASER button toward the
projector and see if it lights green.
Pointer
This remote control unit emits a laser beam as the Laser pointer function from the laser light window. When the LASER
button is pressed, the laser light goes on. When the LASER button is being pressed for more than 1 minute or the LASER
button is released, light goes off. The signal emission indicator lights red and laser is emitted with red light to indicate laser
beam is being emitted.
The laser emitted is a class II laser; therefore, do not look into the laser light window or shine the laser beam on yourself or
other people. The marks below are caution labels for laser beam.
CAUTION : Use of controls, adjustments or performance of procedures other than those specified herein may result in
hazardous radiation exposure. Do not look into the laser light window while laser is emitting, otherwise eye
damage may result.
Laser Light Window
These caution labels are put on the remote control.
Signal Emission Indicator
Laser Pointer Function
NOTE
You can choose the size of Spotlight (Large, Middle, and Small) and the
pattern of Pointer (Arrow, Finger, and Dot) in the Setting Menu. See
“Pointer” on page 40.
Hold down the MENU button and the
NO SHOW button at the same time for
more than 7 seconds.
NO SHOW button
MENU button
PRESENTATION POINTER button
LASER button
PRESENTATION POINTER button
14
Part Names and Functions
This projector has eight different remote control codes (Code 1-Code 8); the factory-set, initial code (Code 1) and the other
seven codes (Code 2 to Code 8). This switching function prevents remote control unit interference when operating several
projectors or video equipment at the same time. (Change the remote control code for the projector first before changing
that for the remote control unit. See “Remote control” on page 40.)
While pressing the MENU button, press the IMAGE button
the number of times corresponding to each remote control
code number. Each time you press the IMAGE button, the
code is changed sequentially. (See the list below.)
1
To initialize the remote control code for the remote control
unit, slide the RESET/ON/ALL-OFF switch to the RESET, and
then to the ON. The initial code is Code 1.
2
Remote Control Code
While pressing the MENU button,
press the IMAGE button number of
times corresponding to the remote
control code for the projector.
Remote Control Code
Number of Times of
Pressing IMAGE Button
Code 1 1
Code 2 2
Code 3 3
Code 4 4
Code 5 5
Code 6 6
Code 7 7
Code 8 8
The remote control unit can be used as a wireless mouse for your computer. Before operating the wireless mouse, connect
your computer and the projector with the supplied USB cable. (See page 17 for connection.) When the Pointer function is
used, the wireless mouse is not available.
Wireless Mouse Operation
Move the pointer on the screen
with this button.
PRESENTATION POINTER button
R-CLICK button
L-CLICK button
MENU button
IMAGE button
Acts as left click while the
projector and a computer are
connected with a USB
cable.
Acts as right click while the
projector and a computer are
connected with a USB
cable.
15
Part Names and Functions
To guarantee safe operation, please observe the following precautions :
Use (2) AA, UM3 or R06 type alkaline batteries.
Replace two batteries at the same time.
Do not use a new battery with a used battery.
Avoid contact with water or liquid.
Do not expose the remote control to moisture, or heat.
Do not drop the remote control.
If a battery has leaked on remote control, carefully wipe case clean and install new batteries.
Risk of explosion if battery is replaced by an incorrect type.
Dispose of used batteries according to the instructions.
Press the lid down-
ward and slide it.
Remove the battery
compartment lid.
Slide the batteries into
the compartment.
Replace the compartment
lid.
Two AA size batteries
For correct polarity (+ and
–), be sure battery
terminals are in contact
with pins in compartment.
12 3
Point the remote control unit toward the projector (Infrared Remote Receiver) whenever pressing any button. Maximum
operating range for the remote control is about 16.4’ (5m) and 60° in front of the projector.
16.4’
(5 m)
60°
Remote Control Batteries Installation
Remote Control Operating Range
16
Installation
Projection angle can be adjusted up to 11.9 degrees with the adjustable feet.
Lift the front of the projector and pull the feet lock latches on
both sides of the projector.
1
Adjustable Feet
Feet Lock Latches
Release the feet lock latches to lock the adjustable feet and
rotate the adjustable feet to adjust the position and tilt.
2
To retract the adjustable feet, lift the front of the projector
and pull and undo the feet lock latches.
Keystone distortion of the projected image can be adjusted
by menu operation. (p20, 38)
3
CAUTION
Tilt the projector within the adjustable range in order to preserve
the life of the lamp. The proper angle should be set. See page 5.
Positioning the Projector
Adjustable Feet
NOTE
The brightness in a room has a great influence on picture quality. It is
recommended to limit ambient lighting in order to provide the best
image.
The values shown are approximate and may vary from the actual size.
100
150
190
300
190
122
95
62
40
A
B
25.3' (7.7m)
16.1' (4.9m)
12.5' (3.8m)
8.2' (2.5m)
Max. Zoom
Min. Zoom
A : B = 9 : 1
Screen Size
(W x H) mm
4 : 3 aspect ratio
Zoom (min)
40”
Zoom (max)
813 x 610
5.2' (1.6m)
3.3' (1.0m)
100”
2032 x 1524
13.1' (4.0m)
8.2' (2.5m)
150”
3048 x 2286
19.7' (6.0m)
12.5' (3.8m)
190”
3861 x 2896
25.3' (7.7m)
16.1' (4.9m)
300”
6096 x 4572
–––––
25.3' (7.7m)
(Inch Diagonal)
3.3' (1.0m)
This projector is designed to project on a flat projection surface and can be focused from 3.3’(1.0m) - 25.3'(7.7m). Refer to
the figure and the table below for the screen size and the distance between the projector and the screen.
(Center)
17
Installation
Connecting to a Computer
AUDIO
R IN L
VIDEO IN
DVI-I/
RGB IN-1
SERVICE PORT
S-VIDEO IN
COMPUTER
AUDIO IN
AUDIO OUT
RGB IN-2/
COMPONENT IN/
RGB OUT
RESET
MCI
ONON
ON
1
DIP
ON
OFF
2 3 4 5 6
13" MODE (640 x 480)
16" MODE (832 x 624)
19" MODE (1024 x 768)
OFF
ON
ON
OFF OFF OFF
OFF OFF OFF
OFF OFF OFF
34 56
OFF OFFON ON21" MODE (1152 x 870)
ON ON
ON
ON
OFF
OFF
12
ON ON
IBM-compatible computer or Macintosh computer (VGA / SVGA / XGA / SXGA)
DVI-VGA Cable
Monitor Output
Desktop type Laptop type
Audio Speaker
(stereo)
Audio Amplifier
Audio Cable
(stereo)
Audio Output
Audio Input
AUDIO OUT
COMPUTER
AUDIO IN
Cables used for connection (= These accessories are not supplied with this projector.)
Audio
Cable
(stereo)
NOTE :
When connecting the cable, the power
cords of both the projector and the
external equipment should be
disconnected from AC outlet.
USB port
MAC Adapter
Set slide switch-
es according to
the chart below.
• VGA Cable (HDB 15 pin)
• DVI-VGA Cable (HDB 15 pin)
• DVI-Digital Cable (for Single Link T.M.D.S.)
• USB Cable
• MAC Adapter (When connecting to Macintosh computer)
• Audio Cables ( Mini Plug (stereo) x 2)
External Audio Equipment
Terminals
of the Projector
VGA
Cable
Monitor Output
or
Monitor Input
USB
RGB IN-2 /
COMPONENT IN/
RGB OUT
Set switches as shown in the table
below depending on RESOLUTION
MODE that you want to use before
you turn on projector and computer.
MAC ADAPTER (Not supplied)
USB
Cable
DVI-I / RGB IN-1
DVI Cable
Monitor Output
NOTE
This terminal is switchable. Set the terminal
up as either Computer input or Monitor
output before using this terminal. (See Page
39.)
DVI-I / RGB IN-1
18
Installation
Connecting to Video Equipment
AUDIO
R IN L
VIDEO IN
DVI-I/
RGB IN-1
SERVICE PORT
S-VIDEO IN
COMPUTER
AUDIO IN
AUDIO OUT
RGB IN-2/
COMPONENT IN/
RGB OUT
RESET
MCI
Video Source (example)
Video Cassette Recorder
Digital Camcorder
S-VIDEO
Cable
Audio Amplifier
Audio Speaker
(stereo)
Audio Cable
(Stereo)
Terminals
of the Projector
S-VIDEO
Output
Audio Input
Video Cable (RCA x 1)
S-VIDEO Cable
Audio Cables (Mini Plug (stereo) x 2 or RCA x 2)
Scart-VGA Cable
Component-VGA Cable
NOTE :
When connecting the cable, the power
cords of both the projector and the
external equipment should be
disconnected from AC outlet.
Audio Output
Audio Cable
(Stereo)
External Audio Equipment
S-VIDEO IN VIDEO IN
AUDIO OUT
Component video output equipment.
(such as DVD player or high-definition TV source.)
Component Video Output
(Y, Pb/Cb, Pr/Cr)
Composite Video Output
Video Cable
(RCA x 1s)
Scart-VGA
Cable
RGB Scart
21-pin Output
Cables used for connection ( = These accessories are not supplied with this projector.)
Component-
VGA Cable
Audio Cable
(RCA x 2)
Audio Output
(R, L)
AUDIO IN
NOTE
The S-VIDEO IN jack has priority over the VIDEO IN jack under
the condition of connecting both the S-VIDEO IN jack and the
VIDEO IN jack when selecting AUTO in the Input Menu.
Select COMPUTER 2 in the Setting Menu when the RGB IN-2/
COMPONENT IN/ RGB OUT terminal is used as RGB Scart 21-
Pin video input or Component video input. (See "Terminal" on
page 39.)
Input sound to the COMPUTER AUDIO IN terminal when
using the RGB IN-2/ COMPONENT IN/ RGB OUT terminal as
input.
RGB IN-2 /
COMPONENT IN/
RGB OUT
RGB IN-2 /
COMPONENT IN/
RGB OUT
COMPUTER
AUDIO IN
19
Basic Operation
Connect the projector's AC power cord into an AC outlet. The
POWER indicator flashes red in a moment and turns on red.
Press the POWER ON-OFF button on the top control or on the
remote control unit. The POWER indicator turns green, and the
cooling fans start to operate. The preparation display appears on
the screen and the count down starts.
2
3
Press the POWER ON-OFF button on the top control or on the
remote control unit, and a message "Power off?" appears on the
screen.
Press the POWER ON-OFF button again to turn off the
projector. The POWER indicator starts to flash red, and it
continues while the cooling fans are operating (for about 90
seconds).
1
2
TO MAINTAIN THE LIFE OF LAMP, ONCE YOU TURN
PROJECTOR ON, WAIT AT LEAST 5 MINUTES BEFORE
TURNING IT OFF.
DO NOT DISCONNECT AC POWER CORD WHILE
COOLING FANS ARE RUNNING OR BEFORE POWER
INDICATOR LIGHTS RED. OTHERWISE IT WILL RESULT
IN SHORTENING LAMP LIFE.
1
3
When the projector has cooled down enough to be turned on
again, the POWER indicator lights red. Then you can disconnect
the AC power cord.
4
After the count-down, the image level that was selected last and
the Lamp mode status icon appear on the screen for 4 seconds,
and the signal from Computer or Video source appears.
Turning On the Projector
Turning Off the Projector
NOTE
The projector cannot be turned on during the cooling period with the
POWER indicator flashing red. You can turn it on again after the POWER
indicator lights red.
When the On start function is on, this projector is turned on automatically by
connecting the AC power cord to an AC outlet. (See page 39 for the On
start function.)
Do not use the projector for more than 24 hours continuously. Turn off the
projector at least once in 24 hours and give it a rest. Continuous use may
result in shortening the lamp life.
This projector monitors internal temperature and automatically controls the
speed of the cooling fans.
If the WARNING indicator flashes or lights red, see “Warning Indicator” on
page 41.
Complete peripheral connections (with a computer, VCR, etc.)
before turning on the projector.
26
The preparation display disappears after 30 seconds.
(See page 40 for Lamp mode.)
Selected Image Level and Lamp Mode
Lamp mode
The message disappears after 4 seconds.
20
If a projected picture has keystone distortion, correct the image with KEYSTONE adjustment.
Basic Operation
The arrows are blue when there is no correction.
The arrows disappear at the maximum correction.
The direction of the arrow being corrected turns light
blue.
If you press the KEYSTONE button on the top control
or on the remote control unit once more while the
keystone dialog box is being displayed, the keystone
adjustment will be canceled.
Keystone Adjustment
Zoom Adjustment
Focus Adjustment
1
Press the KEYSTONE button on the remote control unit or
select Keystone in the Setting Menu (p38). The keystone dialog
box appears.
2
Correct keystone distortion by pressing the Point
Up/Down/Left/Right button. Press the Point Up button to
reduce the upper part of the image, and press the Point Down
button to reduce the lower part. Press the Point Left button to
reduce the left part, and press the Point Right button to reduce
the right part.
Keystone adjustment can be memorized. (p38)
Move the Zoom Lever upward to make the image larger. Move the
Zoom Lever downward to make the image smaller.
Rotate the Focus Ring to adjust the projected picture focus.
Zoom Lever
Focus Ring
Press the FREEZE button on the remote control unit to freeze the
picture on the screen. To cancel the FREEZE function, press the
FREEZE button again or press any other button.
Picture Freeze Function
Reduce the upper width
with Point Up button.
Reduce the lower width
with Point Down button.
Reduce the left part with
Point Left button.
Reduce the right part with
Point Right button.
FREEZE button
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42
  • Page 43 43
  • Page 44 44
  • Page 45 45
  • Page 46 46
  • Page 47 47
  • Page 48 48
  • Page 49 49
  • Page 50 50
  • Page 51 51
  • Page 52 52
  • Page 53 53
  • Page 54 54
  • Page 55 55
  • Page 56 56

Canon 7215 - LV XGA LCD Projector User manual

Category
Projectors
Type
User manual

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI