JL Audio SB-GM-ESCESV/10W1v2 User manual

Brand: JL Audio

Model: SB-GM-ESCESV/10W1v2

Category: Car speakers

Type: User manual

This manual is also suitable for

Thank you for choosing a JL Audio Stealthbox

for your automotive sound system. With proper

installation, your new vehicle-specific enclosed subwoofer system will deliver years of listening pleasure.

We strongly recommend that you have your new Stealthbox

installed by your authorized JL Audio

dealer. The installation professionals employed by your dealer have the necessary tools and experience

to disassemble and reassemble your vehicle properly. Also, keep in mind that your warranty coverage

extends to 2 years if your system is installed or approved by your authorized JL Audio dealer. If you

prefer to perform your own installation, please read this installation guide completely

before beginning the process.

If you choose to perform the installation yourself, it is absolutely vital that

the Stealthbox

be properly mounted to the vehicle according to these

instructions. Failure to mount the enclosure properly presents two problems:

1) The sub-bass performance will suffer due to the movement of the enclosure

caused by the force exerted by the woofer(s).

2) A loose enclosure presents a serious safety hazard in the event of a collision

or sudden deceleration.

S T E P 1

These instructions are for both the short and long

wheelbase versions of this popular SUV.

Empty out the back of the vehicle so that you have a clean

area to work in.

Remove the pocket in the rear quarter interior trim panel on

the drivers side of the vehicle by pulling it up and out. The

wire to power the Stealthbox® needs to come from this open

area, now would be a good time to run that wire. Leave

enough extra to make it easy to make the connection to the

Stealthbox® before it is permanently mounted.

Continued on Next Page

S T E P 2

Looking down through the hole where the pocket had been,

notice the three studs installed at the factory. These studs

will be used to hold down the enclosure.

S T E P 3

The Triangular Plate will be positioned as shown with center

the hole closest to the stud pointing towards the center of

the vehicle..

SB-GM-ESC(ESV)/10W1v2 INSTR_SKU# 011303

INSTALLATION

D I F F I C U LT Y :

OUT

ESTIMATED TIME:

2 HOURS

I N S T A L L A T I O N G U I D E

for the

SB-GM-ESCESV/10W1v2

SB-GM-ESC/10W1v2

SKU#94476-94479 & 94483-94486

2007+

Continued on Next Page

SB-GM-ESC(ESV)/10W1v2 INSTR_SKU# 011303

S T E P 7

Remove the upper rear quarter window trim molding.

S T E P 6

Remove the two woofers from the Stealthbox® and, set it

into place, with the extension going into the previous pocket

location.

Inside the Stealthbox®, where the arrow points, use a small

marker to mark the interior panel where the hole in the

enclosure wall lies.

Remove the Stealthbox®

S T E P 5

Install the Triangular Plate as shown, tighten down the

fasteners that secure the Triangular Plate, leave only the large

Flat washer on top of the Hex nut, Split Lock Washer and

3/8-16 x 1-3/4” Hex Head Bolt. The remaining Flat Washer,

Split Lock Washer and Hex Nut will be installed inside the

enclosure.

S T E P 4

This is a side view of the Bracket shown in STEP 3 with the

included hardware shown for illustration purposes. Install

the 3/8-16 x 1-3/4” Hex Head Bolt through the Triangular

Plate as shown, tighten the Hex Nut that the arrow points

towards. The hardware shown to the left of the 3/8 x 2”

Fender Washer will be inside the Stealthbox® once the

installation is complete.

Page 2 • JL Audio, Inc 2009

S T E P 9

Drill the mark made in STEP 6, enlarge the hole to 1/2 inch.

****CAUTION****

Before drilling, always make sure that you are not

going to be drilling into any gas lines, brake lines,

tires, transmission lines, electrical wiring, exhaust

systems or anything else that might cause a

reduction in your weekly pay.

Always wear eye protection when drilling!

S T E P 1 1

Bolt the bottom hole of the Custom Bracket to the rear

pillar through the hole where the wiring harness had been

secured (see STEP 8). Slide the supplied 3/8-16 Speed Nut

onto the Custom Bracket as shown, align the hole in the

Custom Bracket with the hole in the rear quarter trim panel.

S T E P 1 0

The 1/4” hardware will be installed in the order as shown as

the custom bracket is installed in the vehicle.

NOTE: The arrow points to the upper end of the bracket.

S T E P 8

The upper mount for the lift arm for the tailgate must be

disconnected as shown in order to remove the trim panel.

The wiring harness that runs along the rear pillar has a white

plastic plug (see arrow) that pushes through a hole in the

pillar to locate it. Pull the plug as this hole will be used to

secure the lower end of the Custom Bracket shown in

STEP 10.

SB-GM-ESC(ESV)/10W1v2 INSTR_SKU# 011303

S T E P 1 5

Install the mounting 3/8-16 x 1 3/4” Hex Head Bolt, Split Lock

Washer and Flat Washer through the enclosure wall into the

Speed Nut shown in STEP 11. Also install the Hex Nut, Split

Lock Washer and, Flat Washer on the stud that protrudes

into the bottom of the Stealthbox® from the Triangular

Plate installed in STEP 5. Re-install the woofers into the

Stealthbox®.

C O N G R A T U L A T I O N S !

You have completed the installation for this model!

Enjoy your new Stealthbox®! Please refer to the Power

Recommendation section for an amplifier recommendation

and basic set-up help.

D E T A I L

One way to get the Hex Head Bolt and Flat Washer installed

from the inside of the rear pillar out is to tape them to a

wrench and then guide them through the recently drilled

hole. Once this hardware is in place, tighten all of the

hardware that secures the Custom Bracket in location. With

the Custom Bracket securely installed, replace the upper rear

quarter window trim molding that was removed in STEP 7.

Connect the speaker cables from the amplifier and set the

Stealthbox® in place.

S T E P 1 3

From inside the rear pillar, feed the 1/4-20 x 1” Hex Head Bolt

and 1/4” Flat Washer through the hole drilled in STEP 12 as

shown.

A suggestion on how to get the hardware through the hole

and held in place is shown below.

S T E P 1 2

With the bottom of the Custom Bracket bolted in and

aligned as described in Step 11 drill a hole through the

pillar corresponding with the upper hole in the Custom

Bracket as shown.

****CAUTION****

Before drilling, always make sure that you are not

going to be drilling into any gas lines, brake lines,

tires, transmission lines, electrical wiring, exhaust

systems or anything else that might cause a

reduction in your weekly pay. Always wear eye

protection when drilling!

Page 3 • JL Audio, Inc 2009

All specifications are subject to change without notice. “JL Audio®” and the JL Audio logo, “Stealthbox” and the Stealthbox logo are registered

trademarks of JL Audio, Inc. “Ahead of the Curve” and its respective logo is a trademark of JL Audio, Inc.

#6,294,959 #6,501,844 #6,496,590 #6,441,685 #5,687,247 #6,219,431 #6,625,292 #D472,891 #D480,709 Other U.S. & Foreign patents pending.

For more detailed information please visit us online at www.jlaudio.com.

(954) 443-1100

w w w. j l a u d i o . c o m

1 0 3 6 9 N O R T H C O M M E R C E P A R K W A Y • M I R A M A R , F L O R I D A • 3 3 0 2 5 • U S A

I N C L U D E D H A R D W A R E

1) Triangular Plate 1) Custom Bracket

1/4” Flat Washer 3) 3/8” Split Lock Washer

2) 1/4-20 x 1” Hex Head Bolt 2) 1/4” Split Lock Washer

2) 3/8-16 x 1 3/4” Hex Head Bolt 2) 3/8-16 Hex Nut

2) 1/4-20 Speed Nut 2) 1/4-20 x 1” Hex Head Bolt

2) 3/8 x 1-1/4” Fender Washer 2) 3/8 x 2” Fender Washer

S P E C I F I C A T I O N S

Enclosure Type: Acoustic Suspension (sealed)

Driver Type: (2) 10W1v2-4

Nominal Impedance: 4Ohms per woofer, 2Ohm final load

Continuous Power Handling: 600 Watts

P O W E R R E C O M M E N D A T I O N

JL Audio recommends high quality amplifiers such as the JL Audio HD900/5, 500/1v2, XD600/1 or J2 500.1. The

diagram below shows the recommended crossover, infrasonic filter and equalizer settings for the 500/1v2. If

another amplifier is being used, please reference this illustration and use similar settings on that amplifier.

All JL Audio amplifiers are very versatile audio components. Please consult the owner’s manual for even more

detailed information about installing and tuning your amplifier.

C O N N E C T I O N S

Using quality power, signal and speaker wire is essential in ensuring the performance of your Stealthbox®.

JL Audio recommends using a 4 AWG power kit such as the XC-PCS4-1B for your Stealthbox® amplifier, other

kits are available should you be using more than one amplifier. Signal wire such as the JL Audio Premium

Audio Interconnect Cables should be used that will provide signal for both channels of the amplifier. JL Audio

reccommends using 12AWG speaker wire for subwoofers such as our XC-BCS12-25.

M I D / H I G H F R E Q U E N C Y D R I V E R F I T M E N T

A variety of JL Audio coaxial and component systems will fit in the factory speaker locations of you vehicle.

Front Speaker Size / Location: 6-1/2”- Front Doors

Fits JL Audio Models: TR650-CXi, C2-650x, C3-650, C5-650, C5-650x & ZR650-CSi

Rear Speaker Size / Location: 6-1/2”- Rear Door

Fits JL Audio Models: TR650-CXi, C2-650x, C3-650, C5-650, C5-650x & ZR650-CSi

+12VDC Ground Remote Preamp Output Section

Infrasonic Filter

“Q” Center Freq. Boost (dB)

Amp LP Filter

Advanced

Bass

Control

Amplifier Input Section

Subwoofer Output

MONO OUTP UT ONLY

Left Output Right Output Left Ch. Right Ch.Filter Freq. (Hz) Filter Freq. (Hz)Infrasonic Freq. (Hz) Remote Bass Port

Full Range

Amp Filter

Out Filter

Output Mode Filter Slope Mode

Mode

Slope

Input Voltage Input Sens. Signal Sensing

12dB

24dB

Filter Mode

Bass EQ

Off

12dB

24dB Low

High Off

OnOff

100

200 15

60 40

100

200

0.5

0.7

1.1

1.6

2.7

4.3

80 0

+10

+13

+15

50 0 /1v2

Monoblock Subwoofer Amplifier

JL Audio SB-GM-ESCESV/10W1v2 User manual

Brand: JL Audio

Model: SB-GM-ESCESV/10W1v2

Category: Car speakers

Type: User manual

This manual is also suitable for

Download PDF

report

JL Audio SB-GM-ESCESV/10W1v2 User manual

This manual is also suitable for

JL Audio SB-GM-ESCESV/10W1v2 User manual

Related papers

Other documents