“WET LOOK” GREEN
Concrete & Masonry Lacquer
®
DESCRIPTION
Glaze ‘N Seal “Wet Look” GREEN is a revolutionary super-
low VOC formula (75% lower than previous formulas) that
complies with the strictest air quality regulations in the nation
including South Coast AQMD. It is suitable for use in any
“Green” building project.
This crystal clear acrylic offers the ultimate stain protection in
a high gloss finish indoors and outdoors. It brings life, luster
and a fresh WET appearance to all decorative concrete,
masonry and porous tile. The unique, proprietary deep
penetrating formula provides superior bonding to the surface
reducing the risk of peeling.
USES
“Wet Look” GREEN protects and beautifies all decorative
concrete surfaces, pavers, masonry and porous tile. Ideal for
driveways, patios and garage floors. Also suitable for garden
ponds, fountains and water features.
Prevents oil and grease staining, eliminates concrete dusting
and freeze/thaw problems. Resists UV fading, abrasion and
efflorescence. Enhances true “WET LOOK” of sealed surfaces.
FEATURES
• Non-Yellowing
• Use Indoors or Outdoors
• Fast Drying and Long Lasting
• Re-coatable
• Easy to apply with brush or sprayer
PREPARATIONS
All surfaces must be free of efflorescence, dirt, oil, wax, grease
and defective paint or sealers. If acid has been used, neutralize
surface with a product like Glaze ‘N Seal Neutralizing Rinse
and allow surface to dry thoroughly before applying lacquer.
When water is used, allow surface to dry 72 hours before
sealing.
APPLICATION
Apply 2-4 thin, even coats (depending on porosity of surface)
of “Wet Look“ Green Lacquer with a natural bristle brush,
lamb’s wool applicator or low pressure sprayer (must be solvent
resistant). Allow 1-3 hours between coats or until surface is
dry to touch.
Apply in temperatures between 55º and 80º. Avoid applying
in direct, warm sunlight. Use only in well ventilated areas.
Clean up with lacquer thinner or xylene.
®
Quality Products for Concrete, Tile and Masonry
Glaze ’N Seal Products, Irvine, CA • www.glaze-n-seal.com
FS 70-01/09
IMPORTANT: Product contains petroleum distillates. Read
product label carefully or consult with dealer for more detailed
preparation, application and caution information.
SPECIFICATIONS
GLASS TRANSITION RATE +50º F
DENSITY 7.2 lbs.
TUKON HARDNESS 12-13
CLEAN UP LACQUER THINNER
DRYTIME 1 HOUR
FLASH POINT +34º F
APPLICATIONTEMP 50º F TO 80º F
SPECIAL NOTES
Always test a small area of surface to be sealed to verify
protection and appearance. NOT RECOMMENDED for dense
or presealed surfaces such as glazed tile, quarry tile, marble,
dense brick, dense slate or polished granite.
Do not use if hydrostatice pressure is likely due to heavy
watering runoff, poor drainage or a waterproof membrane
under the surface.
Sealed surface may be slippery when wet. For additional slip
resistance, use Glaze ‘N Seal Grip ‘N Seal additive.
Product coverage will be 100 – 400 square feet per gallon for
the first coat depending on surface porosity. Second coat will
go up to 50% further. DO NOT over apply. Do not allow
Lacquer to puddle on surface.
For added abrasion and wear protection and to extend the
life of the sealer use Glaze ‘N Seal Floor Polish (High Gloss
or Matte) as a traffic coat. Sweep or wash sealed area routinely
to minimize wear from dirt and soil.
Lacquer may be resealed as necessary.
If it is ever necessary to completely remove the existing sealer,
use Glaze ’N Seal Paint, Sealer & Coating Stripper.
GREEN Low VOC formula
protects and beautifies
all decorative concrete,
masonry, porous stone
and more!
Longer Lasting
Professional Results . . . GUARANTEED!
• 75% Lower VOC
• Meets all Air Quality
Requirements
• Deeper Penetrating
Formula
• Non-yellowing
Concrete &
Masonry
Lacquer
Concrete &
Masonry
Lacquer
800/486 -1414
www.glaze-n-seal.com
®
®
IDEAL FOR GREEN PROJECTS!
IDEAL FOR GREEN PROJECTS!
“Wet Look” GREEN
UNSEALED SEALED
“WET LOOK” GREEN
Concrete & Masonry Lacquer
®
DESCRIPTION
Glaze ‘N Seal “Wet Look” GREEN is a revolutionary super-
low VOC formula (75% lower than previous formulas) that
complies with the strictest air quality regulations in the nation
including South Coast AQMD. It is suitable for use in any
“Green” building project.
This crystal clear acrylic offers the ultimate stain protection in
a high gloss finish indoors and outdoors. It brings life, luster
and a fresh WET appearance to all decorative concrete,
masonry and porous tile. The unique, proprietary deep
penetrating formula provides superior bonding to the surface
reducing the risk of peeling.
USES
“Wet Look” GREEN protects and beautifies all decorative
concrete surfaces, pavers, masonry and porous tile. Ideal for
driveways, patios and garage floors. Also suitable for garden
ponds, fountains and water features.
Prevents oil and grease staining, eliminates concrete dusting
and freeze/thaw problems. Resists UV fading, abrasion and
efflorescence. Enhances true “WET LOOK” of sealed surfaces.
FEATURES
• Non-Yellowing
• Use Indoors or Outdoors
• Fast Drying and Long Lasting
• Re-coatable
• Easy to apply with brush or sprayer
PREPARATIONS
All surfaces must be free of efflorescence, dirt, oil, wax, grease
and defective paint or sealers. If acid has been used, neutralize
surface with a product like Glaze ‘N Seal Neutralizing Rinse
and allow surface to dry thoroughly before applying lacquer.
When water is used, allow surface to dry 72 hours before
sealing.
APPLICATION
Apply 2-4 thin, even coats (depending on porosity of surface)
of “Wet Look“ Green Lacquer with a natural bristle brush,
lamb’s wool applicator or low pressure sprayer (must be solvent
resistant). Allow 1-3 hours between coats or until surface is
dry to touch.
Apply in temperatures between 55º and 80º. Avoid applying
in direct, warm sunlight. Use only in well ventilated areas.
Clean up with lacquer thinner or xylene.
®
Quality Products for Concrete, Tile and Masonry
Glaze ’N Seal Products, Irvine, CA • www.glaze-n-seal.com
FS 70-01/09
IMPORTANT: Product contains petroleum distillates. Read
product label carefully or consult with dealer for more detailed
preparation, application and caution information.
SPECIFICATIONS
GLASS TRANSITION RATE +50º F
DENSITY 7.2 lbs.
TUKON HARDNESS 12-13
CLEAN UP LACQUER THINNER
DRYTIME 1 HOUR
FLASH POINT +34º F
APPLICATIONTEMP 50º F TO 80º F
SPECIAL NOTES
Always test a small area of surface to be sealed to verify
protection and appearance. NOT RECOMMENDED for dense
or presealed surfaces such as glazed tile, quarry tile, marble,
dense brick, dense slate or polished granite.
Do not use if hydrostatice pressure is likely due to heavy
watering runoff, poor drainage or a waterproof membrane
under the surface.
Sealed surface may be slippery when wet. For additional slip
resistance, use Glaze ‘N Seal Grip ‘N Seal additive.
Product coverage will be 100 – 400 square feet per gallon for
the first coat depending on surface porosity. Second coat will
go up to 50% further. DO NOT over apply. Do not allow
Lacquer to puddle on surface.
For added abrasion and wear protection and to extend the
life of the sealer use Glaze ‘N Seal Floor Polish (High Gloss
or Matte) as a traffic coat. Sweep or wash sealed area routinely
to minimize wear from dirt and soil.
Lacquer may be resealed as necessary.
If it is ever necessary to completely remove the existing sealer,
use Glaze ’N Seal Paint, Sealer & Coating Stripper.
GREEN Low VOC formula
protects and beautifies
all decorative concrete,
masonry, porous stone
and more!
Longer Lasting
Professional Results . . . GUARANTEED!
• 75% Lower VOC
• Meets all Air Quality
Requirements
• Deeper Penetrating
Formula
• Non-yellowing
Concrete &
Masonry
Lacquer
Concrete &
Masonry
Lacquer
800/486 -1414
www.glaze-n-seal.com
®
®
IDEAL FOR GREEN PROJECTS!
IDEAL FOR GREEN PROJECTS!
“Wet Look” GREEN
UNSEALED SEALED
-
1
-
2
Glaze 'N Seal 114 User manual
- Type
- User manual
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Related papers
Other documents
-
Canton CD1050 W Datasheet
-
-
The Cement Store YELLOW LABEL ANTI SLIP User guide
-
M-Rock BROOKSHIRECORNERS User manual
-
The Cement Store Black Label High Gloss Specification
-
M-Rock 5098 User guide
-
Seal-Krete 334656 User manual
-
Rust-Oleum Automotive 253307 User manual
-
Pond Armor SKU-GRAY-GA User manual
-
Pond Armor SKU-FGREEN-3GA Operating instructions
