Fujitsu RDG12KLLAP Installation guide

Brand: Fujitsu

Model: RDG12KLLAP

Type: Installation guide

This manual is also suitable for

En-1

WARNING

• The appliance shall be installed, operated and stored in a room with a ﬂ oor area larger

than X m².

Amount of refrigerant charge

M (kg)

Minimum room area

X (m

)

M ≤ 1.22

1.22 < M ≤ 1.23

1.45

1.23 < M ≤ 1.50 2.15

1.50 < M ≤ 1.75 2.92

1.75 < M ≤ 2.0 3.82

2.0 < M ≤ 2.5 5.96

2.5 < M ≤ 3.0 8.59

3.0 < M ≤ 3.5 11.68

3.5 < M ≤ 4.0 15.26

(IEC 60335-2-40)

• Installation of this product must be done by experienced service technicians or profes-

sional installers only in accordance with this manual. Installation by non-professional

or improper installation of the product might cause serious accidents such as injury,

water leakage, electric shock, or ﬁ re. If the product is installed in disregard of the

instructions in this manual, it will void the manufacturer’s warranty.

• Do not turn on the power until all work has been completed. Turning on the power be-

fore the work is completed can cause serious accidents such as electric shock or ﬁ re.

• If refrigerant leaks when you are working, ventilate the area. If the leaking refrigerant

is exposed to a direct ﬂ ame, it may produce a toxic gas.

• Installation must be performed in accordance with regulations, codes, or standards for

electrical wiring and equipment in each country, region, or the installation place.

• Do not use means to accelerate the defrosting process or to clean, other than those

recommended by the manufacturer.

• This appliance is not intended for use by persons (including children) with reduced

physical, sensory or mental capabilities, or lack of experience and knowledge, unless

they have been given supervision or instruction concerning use of the appliance by a

person responsible for their safety. Children should be supervised to ensure that they

do not play with the appliance.

• To avoid danger of suffocation, keep the plastic bag or thin ﬁ lm used as the packaging

material away from young children.

• The appliance shall be stored in a room without continuously operating ignition

sources (for example: open ﬂ ames, an operating gas appliance or an operating

electric heater).

• Do not pierce or burn.

• Be aware that refrigerants may not contain an odour.

CAUTION

• Read carefully all safety information written in this manual before you install or use the

air conditioner.

• Install the product by following local codes and regulations in force at the place of

installation, and the instructions provided by the manufacturer.

• This product is part of a set constituting an air conditioner. The product must not be

installed alone or be installed with a device not authorized by the manufacturer.

• Always use a separate power supply line protected by a circuit breaker operating on

all wires with a distance between contact of 3 mm for this product.

• To protect the persons, earth (ground) the product correctly, and use the power cable

combined with an Earth Leakage Circuit Breaker (ELCB).

• This product is not explosion proof, and therefore should not be installed in an explo-

sive atmosphere.

• To avoid getting an electric shock, never touch the electrical components soon after

the power supply has been turned off. After turning off the power, always wait 5 min-

utes or more before you touch the electrical components.

• This product contains no user-serviceable parts. Always consult experienced service

technicians for repairing.

• When moving or relocating the air conditioner, consult experienced service technicians

for disconnection and reinstallation of the product.

• Do not touch the aluminum ﬁ ns of heat exchanger built-in the indoor or outdoor unit to

avoid personal injury when you install or maintain the unit.

• Do not place any other electrical products or household belongings under the product.

Condensation dripping from the product might get them wet, and may cause damage

or malfunction to the property.

• Be careful not to scratch the air conditioner when handling it.

AIR CONDITIONER

Duct type

Contents

1. SAFETY PRECAUTIONS .................................................................. 1

1.1. Precautions for using R32 refrigerant ......................................... 2

2. PRODUCT SPECIFICATION ............................................................. 4

2.1. Installation tools .......................................................................... 4

2.2. Accessories ................................................................................ 4

2.3. Pipe requirement ........................................................................ 4

2.4. Electrical requirement ................................................................. 4

2.5. Optional parts ............................................................................. 5

3. INSTALLATION WORK ..................................................................... 5

3.1. Selecting an installation location ................................................ 5

3.2. Installation dimensions ............................................................... 5

3.3. Installing the unit ......................................................................... 5

3.4. Drain installation ......................................................................... 7

3.5. Pipe installation .......................................................................... 9

3.6. Electrical wiring ......................................................................... 10

3.7. Remote controller setting .......................................................... 13

4. OPTIONAL INSTALLATION WORK ................................................ 13

4.1. Optional kit installation .............................................................. 13

4.2. External input and output .......................................................... 13

4.3. Remote sensor (Optional parts) ............................................... 14

4.4. IR receiver unit (Optional parts) ................................................ 14

4.5. Auto louver grille (Optional parts) ............................................. 14

4.6. Other optional parts .................................................................. 14

4.7. Optional parts cable binding ..................................................... 15

5. REMOTE CONTROL INSTALLATION ............................................. 15

5.1. Group control ............................................................................ 15

5.2. Multiple remote control ............................................................. 16

5.3. DIP switch 101 setting .............................................................. 16

5.4. Simultaneous multi-system operation ....................................... 17

6. FUNCTION SETTING...................................................................... 17

6.1. Function details ........................................................................ 17

7. TEST RUN ....................................................................................... 19

7.1. Check items .............................................................................. 19

7.2. Operation method ..................................................................... 19

8. FINISHING ...................................................................................... 19

9. CUSTOMER GUIDANCE ................................................................ 19

10. ERROR CODES .............................................................................. 19

NOTES:

This manual describes how to install the air conditioner described above. Handling

and installation shall only be done by professionals as outlined in this manual.

1. SAFETY PRECAUTIONS

• Be sure to read this manual thoroughly before installation.

• The warnings and precautions indicated in this manual contain important information

pertaining to your safety. Be sure to observe them.

• Hand this manual, together with the operating manual, to the customer. Request the

customer to keep them on hand for future use, such as for relocating or repairing the

unit.

WARNING

Indicates a potentially or imminently hazardous situation

which, if not avoided, could result in death or serious injury.

CAUTION

Indicates a potentially hazardous situation that may result in

minor or moderate injury or damage to property.

INSTALLATION MANUAL

PART No. 9374342532

[Original instructions] For authorized service personnel only.

EnglishDeutschFrançaisEspañolItalianoEλληvIkάPortuguêsРусский

Türkçe

En-2

1.1. Precautions for using R32 refrigerant

The basic installation work procedures are the same as conventional refrigerant (R410A,

R22) models.

However, pay careful attention to the following points:

Since the working pressure is 1.6 times higher than that of refrigerant R22 models,

some of the piping and installation and service tools are special. (Refer to “2.1. Instal-

lation tools”.)

Especially, when replacing a refrigerant R22 model with a new refrigerant R32 model,

always replace the conventional piping and flare nuts with the R32 and R410A piping and

ﬂ are nuts on the outdoor unit side.

For R32 and R410A, the same ﬂ are nut on the outdoor unit side and pipe can be used.

Models that use refrigerant R32 and R410A have a different charging port thread diam-

eter to prevent erroneous charging with refrigerant R22 and for safety. Therefore, check

beforehand. [The charging port thread diameter for R32 and R410A is 1/2-20 UNF.]

Be more careful than R22 so that foreign matter (oil, water, etc.) does not enter the

piping. Also, when storing the piping ,securely seal the opening by pinching, taping, etc.

(Handling of R32 is similar to R410A.)

CAUTION

1-Installation (Space)

• That the installation of pipe-work shall be kept to a minimum.

• That pipe-work shall be protected from physical damage.

• The appliance shall not be installed in an unventilated space, if that space is smaller

than X m².

Amount of refrigerant charge

M (kg)

Minimum room area

X (m

)

M ≤ 1.22

1.22 < M ≤ 1.23

1.45

1.23 < M ≤ 1.50 2.15

1.50 < M ≤ 1.75 2.92

1.75 < M ≤ 2.0 3.82

2.0 < M ≤ 2.5 5.96

2.5 < M ≤ 3.0 8.59

3.0 < M ≤ 3.5 11.68

3.5 < M ≤ 4.0 15.26

(IEC 60335-2-40)

• That compliance with national gas regulations shall be observed.

• That mechanical connections shall be accessible for maintenance purposes.

• In cases that require mechanical ventilation, ventilation openings shall be kept clear

of obstruction.

• When disposing of the product is used, be based on national regulations, properly

processed.

2-Servicing

2-1 Service personnel

• Any person who is involved with working on or breaking into a refrigerant circuit

should hold a current valid certiﬁ cate from an industry-accredited assessment

authority, which authorises their competence to handle refrigerants safely in accor-

dance with an industry recognised assessment speciﬁ cation.

• Servicing shall only be performed as recommended by the equipment manufacturer.

Maintenance and repair requiring the assistance of other skilled personnel shall be

carried out under the supervision of the person competent in the use of ﬂ ammable

refrigerants.

• Servicing shall be performed only as recommended by the manufacturer.

2-2 Work

• Prior to beginning work on systems containing ﬂ ammable refrigerants, safety checks

are necessary to ensure that the risk of ignition is minimized. For repair to the refrig-

erating system, the precautions in 2-2 to 2-8 shall be complied with prior to conduct-

ing work on the system.

• Work shall be undertaken under a controlled procedure so as to minimize the risk of

a ﬂ ammable gas or vapour being present while the work is being performed.

• All maintenance staff and others working in the local area shall be instructed on the

nature of work being carried out.

• Work in conﬁ ned spaces shall be avoided.

• The area around the workspace shall be sectioned off.

• Ensure that the conditions within the area have been made safe by control of ﬂ am-

mable material.

2-3 Checking for presence of refrigerant

• The area shall be checked with an appropriate refrigerant detector prior to and during

work, to ensure the technician is aware of potentially ﬂ ammable atmospheres.

• Ensure that the leak detection equipment being used is suitable for use with ﬂ am-

mable refrigerants, i.e. nonsparking, adequately sealed or intrinsically safe.

2-4 Presence of ﬁ re extinguisher

• If any hot work is to be conducted on the refrigeration equipment or any associated

parts, appropriate ﬁ re extinguishing equipment shall be available at hand.

• Have a dry powder or CO

ﬁ re extinguisher adjacent to the charging area.

CAUTION

2-5 No ignition sources

• No person carrying out work in relation to a refrigeration system which involves

exposing any pipe work that contains or has contained ﬂ ammable refrigerant shall

use any sources of ignition in such a manner that it may lead to the risk of ﬁ re or

explosion.

• All possible ignition sources, including cigarette smoking, should be kept sufﬁ ciently

far away from the site of installation, repairing, removing and disposal, during which

ﬂ ammable refrigerant can possibly be released to the surrounding space.

• Prior to work taking place, the area around the equipment is to be surveyed to make

sure that there are no ﬂ ammable hazards or ignition risks. “No Smoking” signs shall

be displayed.

2-6 Ventilated area

• Ensure that the area is in the open or that it is adequately ventilated before breaking

into the system or conducting any hot work.

• A degree of ventilation shall continue during the period that the work is carried out.

• The ventilation should safely disperse any released refrigerant and preferably expel

it externally into the atmosphere.

2-7 Checks to the refrigeration equipment

• Where electrical components are being changed, they shall be ﬁ t for the purpose

and to the correct speciﬁ cation.

• At all times the manufacturer’s maintenance and service guidelines shall be followed.

• If in doubt consult the manufacturer’s technical department for assistance.

• The following checks shall be applied to installations using ﬂ ammable refrigerants.

- The charge size is in accordance with the room size within which the refrigerant

containing parts are installed.

- The ventilation machinery and outlets are operating adequately and are not

obstructed.

- If an indirect refrigerating circuit is being used, the secondary circuit shall be

checked for the presence of refrigerant.

- Marking to the equipment continues to be visible and legible. Markings and signs

that are illegible shall be corrected.

- Refrigeration pipe or components are installed in a position where they are unlikely

to be exposed to any substance which may corrode refrigerant containing compo-

nents, unless the components are constructed of materials which are inherently

resistant to being corroded or are suitably protected against being so corroded.

2-8 Checks to electrical devices

• Repair and maintenance to electrical components shall include initial safety checks

and component inspection procedures.

• If a fault exists that could compromise safety, then no electrical supply shall be con-

nected to the circuit until it is satisfactorily dealt with.

• If the fault cannot be corrected immediately but it is necessary to continue operation,

an adequate temporary solution shall be used.

• This shall be reported to the owner of the equipment so all parties are advised.

• Initial safety checks shall include.

- That capacitors are discharged: this shall be done in a safe manner to avoid pos-

sibility of sparking.

- That there no live electrical components and wiring are exposed while charging,

recovering or purging the system.

- That there is continuity of earth bonding.

3-Repairs to sealed components

• During repairs to sealed components, all electrical supplies shall be disconnected

from the equipment being worked upon prior to any removal of sealed covers, etc.

• If it is absolutely necessary to have an electrical supply to equipment during servic-

ing, then a permanently operating form of leak detection shall be located at the most

critical point to warn of a potentially hazardous situation.

• Particular attention shall be paid to the following to ensure that by working on electri-

cal components, the casing is not altered in such a way that the level of protection is

affected.

• This shall include damage to cables, excessive number of connections, terminals not

made to original speciﬁ cation, damage to seals, incorrect ﬁ tting of glands, etc.

• Ensure that apparatus is mounted securely.

• Ensure that seals or sealing materials have not degraded such that they no longer

serve the purpose of preventing the ingress of ﬂ ammable atmospheres.

• Replacement parts shall be in accordance with the manufacturer’s speciﬁ cations.

NOTES: The use of silicon sealant may inhibit the effectiveness of some types of leak

detection equipment.

Intrinsically safe components do not have to be isolated prior to working on

them.

4-Repair to intrinsically safe components

• Do not apply any permanent inductive or capacitance loads to the circuit without

ensuring that this will not exceed the permissible voltage and current permitted for

the equipment in use.

• Intrinsically safe components are the only types that can be worked on while live in

the presence of a ﬂ ammable atmosphere.

• The test apparatus shall be at the correct rating.

• Replace components only with parts speciﬁ ed by the manufacturer.

• Other parts may result in the ignition of refrigerant in the atmosphere from a leak.

En-3

CAUTION

5-Cabling

• Check that cabling will not be subject to wear, corrosion, excessive pressure, vibra-

tion, sharp edges or any other adverse environmental effects.

• The check shall also take into account the effects of aging or continual vibration from

sources such as compressors or fans.

6-Detection of ﬂ ammable refrigerants

• Under no circumstances shall potential sources of ignition be used in the searching

for or detection of refrigerant leaks.

• A halide torch (or any other detector using a naked ﬂ ame) shall not be used.

7-Leak detection methods

• Electronic leak detectors shall be used to detect ﬂ ammable refrigerants, but the

sensitivity may not be adequate, or may need re-calibration. (Detection equipment

shall be calibrated in a refrigerant-free area.)

• Ensure that the detector is not a potential source of ignition and is suitable for the

refrigerant used.

• Leak detection equipment shall be set at a percentage of the LFL of the refrigerant

and shall be calibrated to the refrigerant employed and the appropriate percentage of

gas (25 % maximum) is conﬁ rmed.

• Leak detection ﬂ uids are suitable for use with most refrigerants but the use of

detergents containing chlorine shall be avoided as the chlorine may react with the

refrigerant and corrode the copper pipe-work.

• If a leak is suspected, all naked ﬂ ames shall be removed/extinguished.

• If a leakage of refrigerant is found which requires brazing, all of the refrigerant shall

be recovered from the system, or isolated (by means of shut off valves) in a part of

the system remote from the leak.

Oxygen free nitrogen (OFN) shall then be purged through the system both before

and during the brazing process.

8-Removal and evacuation

• When breaking into the refrigerant circuit to make repairs – or for any other

purpose –conventional procedures shall be used.

However, it is important that best practice is followed since ﬂ ammability is a consid-

eration.

The following procedure shall be adhered to:

• remove refrigerant

• purge the circuit with inert gas

• evacuate

• purge again with inert gas

• open the circuit by cutting or brazing

• The refrigerant charge shall be recovered into the correct recovery cylinders.

• The system shall be “ﬂ ushed” with OFN to render the unit safe.

• This process may need to be repeated several times.

• Compressed air or oxygen shall not be used for this task.

• Flushing shall be achieved by breaking the vacuum in the system with OFN and

continuing to ﬁ ll until the working pressure is achieved, then venting to atmosphere,

and ﬁ nally pulling down to a vacuum.

• This process shall be repeated until no refrigerant is within the system.

• When the ﬁ nal OFN charge is used, the system shall be vented down to atmospheric

pressure to enable work to take place.

• This operation is absolutely vital if brazing operations on the pipe work are to take

place.

• Ensure that the outlet for the vacuum pump is not close to any ignition sources and

there is ventilation available.

9-Charging procedures

• In addition to conventional charging procedures, the following requirements shall be

followed.

- Ensure that contamination of different refrigerants does not occur when using

charging equipment.

Hoses or lines shall be as short as possible to minimize the amount of refrigerant

contained in them.

- Cylinders shall be kept upright.

- Ensure that the refrigeration system is earthed prior to charging the system with

refrigerant.

- Label the system when charging is complete (if not already).

- Extreme care shall be taken not to overﬁ ll the refrigeration system.

• Prior to recharging the system it shall be pressure tested with OFN.

• The system shall be leak tested on completion of charging but prior to commission-

ing.

• A follow up leak test shall be carried out prior to leaving the site.

CAUTION

10-Decommissioning

• Before carrying out this procedure, it is essential that the technician is completely

familiar with the equipment and all its details.

• It is recommended good practice that all refrigerants are recovered safely.

• Prior to the task being carried out, an oil and refrigerant sample shall be taken in

case analysis is required prior to re-use of reclaimed refrigerant.

• It is essential that electrical power is available before the task is commenced.

a) Become familiar with the equipment and its operation.

b) Isolate system electrically.

c) Before attempting the procedure ensure that:

• mechanical handling equipment is available, if required, for handling refriger-

ant cylinders;

• all personal protective equipment is available and being used correctly;

• the recovery process is supervised at all times by a competent person;

• recovery equipment and cylinders conform to the appropriate standards.

d) Pump down refrigerant system, if possible.

e) If a vacuum is not possible, make a manifold so that refrigerant can be removed

from various parts of the system.

f) Make sure that cylinder is situated on the scales before recovery takes place.

g) Start the recovery machine and operate in accordance with manufacturer’s

instructions.

h) Do not overﬁ ll cylinders. (No more than 80 % volume liquid charge).

i) Do not exceed the maximum working pressure of the cylinder, even temporarily.

j) When the cylinders have been ﬁ lled correctly and the process completed, make

sure that the cylinders and the equipment are removed from site promptly and all

isolation valves on the equipment are closed off.

k) Recovered refrigerant shall not be charged into another refrigeration system un-

less it has been cleaned and checked.

11-Labelling

• Equipment shall be labelled stating that it has been de-commissioned and emptied

of refrigerant.

• The label shall be dated and signed.

• Ensure that there are labels on the equipment stating the equipment contains ﬂ am-

mable refrigerant.

12-Recovery

• When removing refrigerant from a system, either for servicing or decommissioning, it

is recommended good practice that all refrigerants are removed safely.

• When transferring refrigerant into cylinders, ensure that only appropriate refrigerant

recovery cylinders are employed.

• Ensure that the correct number of cylinders for holding the total system charge are

available.

• All cylinders to be used are designated for the recovered refrigerant and labelled for

that refrigerant (i.e. special cylinders for the recovery of refrigerant).

• Cylinders shall be complete with pressure relief valve and associated shut-off valves

in good working order.

• Empty recovery cylinders are evacuated and, if possible, cooled before recovery

occurs.

• The recovery equipment shall be in good working order with a set of instructions

concerning the equipment that is at hand and shall be suitable for the recovery of

ﬂ ammable refrigerants.

• In addition, a set of calibrated weighing scales shall be available and in good working

order.

• Hoses shall be complete with leak-free disconnect couplings and in good condition.

• Before using the recovery machine, check that it is in satisfactory working order, has

been properly maintained and that any associated electrical components are sealed

to prevent ignition in the event of a refrigerant release.

Consult manufacturer if in doubt.

• The recovered refrigerant shall be returned to the refrigerant supplier in the correct

recovery cylinder, and the relevant Waste Transfer Note arranged.

• Do not mix refrigerants in recovery units and especially not in cylinders.

• If compressors or compressor oils are to be removed, ensure that they have been

evacuated to an acceptable level to make certain that ﬂ ammable refrigerant does not

remain within the lubricant.

• The evacuation process shall be carried out prior to returning the compressor to the

suppliers.

• Only electric heating to the compressor body shall be employed to accelerate this

process.

• When oil is drained from a system, it shall be carried out safely.

Explanation of symbols displayed on the indoor unit or outdoor unit.

WARNING

This symbol shows that this appliance uses a ﬂ ammable

refrigerant.

If the refrigerant is leaked and exposed to an external igni-

tion source, there is a risk of ﬁ re.

CAUTION

This symbol shows that the operation manual should be

read carefully.

CAUTION

This symbol shows that a service personnel should be

handling this equipment with reference to the installation

manual.

CAUTION

This symbol shows that information is available such as

the operating manual or installation manual.

En-4

2. PRODUCT SPECIFICATION

2.1. Installation tools

Tool name Change from R22 to R32 (R410A)

Gauge manifold

Pressure is high and cannot be measured with a R22

gauge. To prevent erroneous mixing of other refrigerants,

the diameter of each port has been changed.

It is recommended to use gauge with seals -0.1 to 5.3 MPa

(-1 to 53 bar) for high pressure.

-0.1 to 3.8 MPa (-1 to 38 bar) for low pressure.

Charge hose

To increase pressure resistance, the hose material and base

size were changed. (R32/R410A)

Vacuum pump

A conventional vacuum pump can be used by installing a

vacuum pump adapter.

(Use of a vacuum pump with a series motor is prohibited.)

Gas leakage detector

Special gas leakage detector for HFC refrigerant R410A or

R32.

■

Copper pipes

It is necessary to use seamless copper pipes and it is desirable that the amount of residual

oil is less than 40 mg/10 m. Do not use copper pipes having a collapsed, deformed or

discolored portion (especially on the interior surface). Otherwise, the expansion value or

capillary tube may become blocked with contaminants.

As an air conditioner using R32 (R410A) incurs pressure higher than when using R22, it is

necessary to choose adequate materials.

WARNING

• Do not use the existing (for R22) piping and ﬂ are nuts.

If the existing materials are used, the pressure inside the refrigerant cycle will rise and

cause failure, injury, etc. (Use the special R32/R410A materials.)

• Use (reﬁ ll or replace with) speciﬁ ed refrigerant (R32) only. Use of unspeciﬁ ed refriger-

ant can cause product malfunction, burst, or injury.

• Do not mix any gas or impurities except speciﬁ ed refrigerant (R32). Inﬂ ow of air or ap-

plication of unspeciﬁ ed material makes the internal pressure of the refrigerant cycle too

high, and may cause product malfunction, burst of piping, or injury.

• For installation purposes, be sure to use the parts supplied by the manufacturer or

other prescribed parts. The use of non-prescribed parts can cause serious accidents

such as the unit falling, water leakage, electric shock, or ﬁ re.

• Do not turn on the power until all work has been completed.

CAUTION

This manual describes how to install the indoor unit only. To install the outdoor unit or

branch box, (if any), refer to the installation manual included in each product.

2.2. Accessories

WARNING

• For installation purposes, be sure to use the parts supplied by the manufacturer or

other prescribed parts. The use of non-prescribed parts can cause serious accidents

such as the unit to fall, water leakage, electric shock, or ﬁ re.

• Keep the Installation manual in a safe place and do not discard any other accessories

until the installation work has been completed.

The following installation accessories are supplied. Use them as required.

Name and Shape

Q’ty

Name and Shape

Q’ty

Operating manual

Cable tie (large)

Operating manual

(CD-ROM)

Cable tie (medium)

Installation manual

(This manual)

Filter (large)

[18 model]

Installation template

Filter (small)

[07, 09,12,14 model]

Washer

Drain hose

Coupler heat insulation (large)

Hose band

Coupler heat insulation(small)

Drain hose insulation B

Insulation

(for electrical wiring)

The following items are necessary to install this air conditioner. (The items are not includ-

ed with the air conditioner and must be purchased separately.)

Additional materials

Connection pipe assembly Wall cap

Connection cable (4-conductor)

Saddle

Wall pipe Drain hose

Decorative tape Tapping screws

Vinyl tape Putty

2.3. Pipe requirement

Model

Gas pipe size (thickness) [mm] Luquid pipe size (thickness) [mm]

07, 09, 12,14 Ø 9.52 (0.80) Ø 6.35 (0.80)

Ø 12.70 (0.80) Ø 6.35 (0.80)

CAUTION

Refer to the installation manual for the outdoor unit for description of allowable pipe

length and height difference.

• Use pipe with water-resistant heat insulation.

CAUTION

• Wrap heat insulation around both gas pipe and liquid pipe.

No heat-insulation work or incorrect heat-insulation work may cause water leaks.

• In a reverse cycle model, use heat insulation with heat resistance above 120 °C.

• If expected humidity of the installation location of refrigerant pipes is higher than

70 %, wrap the heat insulation around the refrigerant pipes.

If the expected humidity is between 70 % and 80 %, use heat insulation that has a

thickness of 15 mm or more.

If the expected humidity is higher than 80 %, use heat insulation that has a thickness

of 20 mm or more.

• The use of thinner heat insulation than speciﬁ ed above, may cause a condensation

on the surface of the insulation.

• Use heat insulation with thermal conductivity of 0.045 W/(

m•K

) or less, at 20

°C

2.4. Electrical requirement

The indoor unit is powered from the outdoor unit. Do not power indoor unit from separate

power source.

WARNING

Standard for electrical wiring and equipment differs in each country or region. Before you

start electrical working, conﬁ rm related regulations, codes, or standards.

Cable

Conductor size [

] Type

Remarks

Connection cable

1.5 (Min) Type 60245 IEC 57

3 cable + Earth (Ground),

1 Ø 230 V

Cable Length: Limit voltage drop to less than 2%. Increase cable gauge if voltage drop is

2% or more.

En-5

2.5. Optional parts

Refer to each installation manual for the method of installing optional parts.

Parts name Model No. Application

Wired remote controller

UTY-RNR



For air conditioner operation

(2-wired type)

UTY-RLR



UTY-RVN



For air conditioner operation

(3-wired type)

UTY-RNN



Simple remote controller

UTY-RSR



For air conditioner operation

(2-wired type)

UTY-RHR



UTY-RSN



For air conditioner operation

(3-wired type)

IR receiver unit UTY-LBT



M For the wireless remote controller

Remote sensor unit UTY-XSZX Room temperature sensor

Auto louver grille kit

UTD-GXTA-W

Air outlet grille with outo louver

(07, 09,12,14 models)

UTD-GXTB-W

Air outlet grille with outo louver

(18 model)

External connect kit

PCB terminal For control input port

UTY-XWZXZG For control output port

W-LAN interface UTY-TFSXZ1 For wireless LAN control

3. INSTALLATION WORK

WARNING

Do not move the appliance by holding the indoor unit pipes.

(The stress applied to the pipe joints may cause the ﬂ ammable gas to leak during

operation.)

3.1. Selecting an installation location

Especially, the installation place is very important for the split type air conditioner because it

is very difﬁ cult to move from place to place after the ﬁ rst installation.

WARNING

Select installation locations that can properly support the weight of the indoor. Install

the units securely so that they do not topple or fall.

CAUTION

• Do not install the unit in the following areas:

- Area with high salt content, such as at the seaside. It will deteriorate metal parts,

causing the parts to fail or the unit to leak water.

- Area ﬁ lled with mineral oil or containing a large amount of splashed oil or steam,

such as a kitchen. It will deteriorate plastic parts, causing the parts to fail or the

unit to leak water.

- Area where is close to heat sources.

- Area that generates substances that adversely affect the equipment, such as

sulfuric gas, chlorine gas, acid, or alkali. It will cause the copper pipes and brazed

joints to corrode, which can cause refrigerant leakage.

- Area that can cause combustible gas to leak, contains suspended carbon ﬁ bers or

ﬂ ammable dust, or volatile in ﬂ ammables such as paint thinner or gasoline.

- If gas leaks and settles around the unit, it can cause a ﬁ re.

- Area where animals may urinate on the unit or ammonia may be generated.

• Do not use the unit for special purposes, such as storing food, raising animals, grow-

ing plants, or preserving precision devices or art objects. It can degrade the quality

of the preserved or stored objects.

• Install the unit where drainage does not cause any trouble.

• Install the indoor unit, outdoor unit, power supply cable, transmission cable, and

remote control cable at least 1 m away from a television or radio receivers. The

purpose of this is to prevent TV reception interference or radio noise.

(Even if they are installed more than 1 m apart, you could still receive noise under

some signal conditions.)

• If children under 10 years old may approach the unit, take preventive measures so

that they cannot reach the unit.

• Decide the mounting position with the customer as follows:

(1) Install the indoor unit in a location having sufﬁ cient strength to support the weight of

the indoor unit.

(2) The inlet and outlet ports should not be obstructed; the air should be able to blow all

over the room.

(3) Leave the space required to service the air conditioner.

(4) Locate where the air can be distributed evenly throughout the room by the unit.

(5) Install the unit where connection to the outdoor unit is easy.

(6) Install the unit where the connection pipe can be easily installed.

(7) Install the unit where the drain pipe can be easily installed.

(8) Install the unit where noise and vibration is not ampliﬁ ed.

(9) Take servicing, etc., into consideration and leave the spaces. Also install the unit

where the ﬁ lter can be removed.

3.2. Installation dimensions

Provide a Service access for inspection purposes.

Do not place any wiring or illumination in the service space, as they will impede service.

Left

side

Strong and durable ceiling

Indoor unit

Right

side

150 mm

or more

400 mm

or more

Service access Ceiling

2500 mm or more

(When no ceiling)

Floor

240 mm or more

20 mm or more

300 mm or more

Adjust the wind direction in the room depending on the shape of blow out opening.

Service access

Unit

Control

box

400 mm

or more

100 mm

or more

300 mm

or more

Service space

3.3. Installing the unit

WARNING

• Install the air conditioner in a location which can withstand a load do at least 5 times

the weight of the main unit and which will not amplify sound or vibration. If the instal-

lation location is not strong enough, the indoor unit may fall and cause injuries.

• If the work is done with the panel frame only, there is a risk that the unit will come

loose. Please take care.

3.3.1. Unit installation example

■

Connect the locally purchased duct:

(1) Inlet side

• Connect the duct to the locally purchased inlet ﬂ ange.

• Connect the ﬂ ange to the body with the locally purchased tapping screws.

• Wind the inlet ﬂ ange connecting to the duct with the aluminum tape etc. to avoid the

air discharge.

CAUTION

When the duct is connected to inlet side, remove contained ﬁ lter and surely attach

locally purchased ﬁ lter at inlet opening.

(2) Outlet side

• Connect the duct with adjusting inside of outlet ﬂ ange.

• Wind the outlet ﬂ ange connecting to the duct with the aluminum tape etc. to avoid the

air discharge.

• Insulate the duct to avoid the dew condensation.

En-6

CAUTION

• Check that duct work does not exceed the range of external static pressure of equip-

ment.

• Make sure to insulate ducts to avoid the dew condensation.

• Make sure to insulate between ducts and walls if metal ducts are used.

•

Please explain handling and washing methods of locally purchased materials to the

customer.

• To prevent people from touching the parts inside the unit, be sure to install grilles on

the inlet and outlet ports. The grilles must be designed in such a way that cannot be

removed without tools.

• When connecting the duct to the outlet port of the indoor unit, be sure to insulate the

outlet port and the installation screws to prevent water from leaking around the port.

• Set the static pressure outside the unit to 90 Pa or less (the allowable range is be-

tween 0 and 90 Pa.)

■

Replace the cover as follows:

• Remove the screws, and then remove cover and fan guard.

• Install the cover with the screws as shown in the illustration below.

Model Screw

07, 09, 12, 14 9

18 11

Screw

Cover

Fan guard

Side inlet - Side outlet

Insulation material (Locally purchased)

Aluminum tape

Flange (Locally purchased)

Air

Duct

(Locally purchased)

Air

Intake grille

(Locally

purchased)

Side inlet - Side outlet (Duct)

Insulation material (Locally purchased)

Aluminum tape

Tapping screw for

ﬂ ange connection

(M4 x 10mm /

Locally

purchased)

Flange (Locally purchased)

Air

Duct

(Locally purchased)

Air

Intake grille

(Locally purchased)

Bottom inlet - Side outlet

Duct (Locally purchased)

Intake grille (Locally purchased)

Air

Outlet side

Inlet side

07, 09, 12,14 models 18 model

A 650 mm 850 mm

B P200×2=400 mm P200×3=600 mm

CAUTION

• Be sure to install the air inlet grille and the air outlet grille for air circulation. The cor-

rect temperature cannot be detected.

• Grills must be ﬁ xed so that man cannot touch indoor unit fan and exchanger, and

cannot be removed by only hand operation without tool.

• Be sure to install the air ﬁ lter in the air inlet.

If the air ﬁ lter is not installed, the heat exchanger may be clogged and its perfor-

mance may decrease.

3.3.2. Install the ﬁ lters

• Install the ﬁ lters to the unit.

Filter (accessories)

Unit

Filter

3.3.3. Position the ceiling hole and hanging bolts

• Using the installation template, drill holes for bolts (4 holes).

Drilling position

for bolts

Installation template

(accessory)

Air

377 mm

07, 09, 12, 14 models 18 model

A 734 mm 934 mm

En-7

3.4. Drain installation

3.4.1. Installing drain pipes

WARNING

• Do not insert the drain piping into the sewer where sulfurous gas occurs. (Heat ex-

change erosion may occur)

• Insulate the parts properly so that water will not drip from the connection parts.

• Check for proper drainage after the construction by using the visible portion of trans-

parent drain port and the drain piping ﬁ nal outlet on the body.

CAUTION

Do not apply adhesive agent on the drain port of the body.

(Use the attached drain hose and connect the drain piping)

■

When drain pump is used

• Use general hard polyvinyl chloride pipe (VP25) [outside diameter 32 mm].

• Do not perform a rise, trap and air bleeding.

• Provide a downward gradient (1/100 or more).

• Provide supporters when long pipes are installed.

• Use an insulation material as needed, to prevent the pipes from freezing.

• Install the pipes in a way that allows for the removal of the control box.

Gap of 1.5 to 2 m

700 mm or

less

Horizontal or

upward gradient

Supporter

Max. 300 mm

Locally arranged pipe

GOOD

VP25 [O.D

32 mm or more]

Rise

Air bleeding

PROHIBITED

Trap

Observe the following procedures to construct centralized drain pipe ﬁ ttings.

VP30 or more [O.D 38 mm or more]

Downward gradient 1/100 or more

700 mm or less

■

When drain pump is not used (natural drainage)

CAUTION

Set “Drainage function setting (DIP switch 101-1)” in “5.3. DIP switch 101 setting”

If the drain pump is not used, please replace with the drain cap.

• Use general hard polyvinyl chloride pipe (VP25) [outside diameter 32 mm].

• Do not perform a rise, trap and air bleeding.

3.3.4. Fix the unit

(1) Hang the unit

Hanger bolt

Nut A

(Locally purchased)

Nut B

(Locally purchased)

Washer

(accessories)

Hanger

Hanger bolt

Nut A

(Locally purchased)

Washer

(accessories)

Nut B

(Locally purchased)

Unit

Hanger

20mm

length

Cover

* It might become difﬁ cult to open and shut the Cover /control box cover when the length

exceeds 20mm.

(2) Leveling

Base horizontal direction leveling on top of the unit.

Ceiling

Level

PROHIBITED

10 mm or less

Level

Air

OK PROHIBITED

10 mm or less

CAUTION

• Leave a space of 100 mm or more between the inlet port and the ceiling.

• Fasten the unit securely with Special nuts A and B.

En-8

• Provide a downward gradient (1/100 or more).

• Provide supporters when long pipes are installed.

• Use an insulation material as needed, to prevent the pipes from freezing.

• Install the pipes in a way that allows for the removal of the control box.

Gap of 1.5 to 2 m

100 mm or more

ownward gradient

2.5-5.0 mm

Supporter

Locally arranged pipe

GOOD

VP25 [O.D 32 mm

or more]

Air bleeding

Rise

PROHIBITED

Trap

Observe the following procedures to construct centralized drain pipe ﬁ ttings.

VP30 or more

[O.D 38 mm or more]

Downward gradient

1/100 or more

3.4.2. Installing the drain hose (accsessory) and drain pipe (locally purchased)

(1) Be sure to use supplied Drain hose and Hose band

Hose band (accessory)

Drain

hole

Drain hose (accessory)

Hard PVC side

Hose band

4 mm or less

20 mm

Hose band

Drain hose

Fasten the Hose band at the position where

horizontal against ground.

The Hose band must be positioned at the right

side of the Drain hose as in the ﬁ gure.

(2) Be sure to connect Drain pipe with adhesive (polyvinyl chloride) so that there is no

leakage.

Applying

area of

adhesive

Joint pipe

(Locally purchased)

Drain pipe (VP25)

(Locally purchased)

4 mm or less

CAUTION

Do not connect to the Drain hole with adhesive. Using adhesive may cause damage

and water leaks.

(3) After installing the Drain hose, check if the drainage is smooth.

CAUTION

To prevent excessive force on Drain hose, avoid bends or twists. (To bend or twist

may cause water leaks.)

(4) After checking for drainage, attach the Drain hose insulation B to insulate, following

the instructions as in the ﬁ gures.

To avoid space with Drain hose and Hose band, press ﬁ rmly the Drain hose insulation B.

Drain hose

insulation B

(accessory)

Ensure there is

no space.

• STEP 1 to STEP 3

Butt the insulation

against the unit.

STEP 1

Unit

Slit

Press ﬁ rmly

STEP 2

Slit

Press ﬁ rmly

Roll the

insulation

over the joint.

Press ﬁ rmly

STEP 3

Press ﬁ rmly

Slit

• FINISH

Check that there is no gap between the unit and the drain hose insulation.

En-9

• When drain pump is used.

Do not cover the

panel window.

• When drain pump is not used. (Natural drainage)

Do not cover the

control box cover.

NOTES: Check for drainage

Pour about 1 liter of water from the position shown in the diagram or from the airﬂ ow

outlet to the dew tray. Check for any abnormalities such as strange noises and whether

the drain pump functions normally.

CAUTION

Make sure the drain water is properly drained.

3.5. Pipe installation

3.5.1. Pipe connection

CAUTION

Tighten the flare nuts with a torque wrench using the specified tightening method.

Otherwise, the ﬂ are nuts could break after a prolonged period, causing refrigerant to leak

and generate hazardous gas if the refrigerant comes into contact with a ﬂ ame.

■

Flaring

Use special pipe cutter and ﬂ are tool designed for R410A or R32 pipework.

(1) Cut the connection pipe to the necessary length with a pipe cutter.

(2) Hold the pipe downward so that cuttings will not enter the pipe and remove any burrs.

(3) Insert the ﬂ are nut (always use the ﬂ are nut attached to the indoor unit(s) and outdoor

unit or branch box respectively) onto the pipe and perform the ﬂ are processing with a

ﬂ are tool. Use the special R410A or R32 ﬂ are tool, or the conventional ﬂ are tool. Leak-

age of refrigerant may result if other ﬂ are nuts are used.

(4) Protect the pipes by pinching them or with tape to prevent dust, dirt, or water from

entering the pipes.

Die

Pipe

Check if [L] is flared uniformly

and is not cracked or scratched.

Pipe outside diameter

[mm (in.)]

Dimension A [mm]

Dimension B [mm]

Flare tool for R32, clutch

type

6.35 (1/4)

0 to 0.5

9.1

9.52 (3/8) 13.2

12.70 (1/2) 16.6

15.88 (5/8) 19.7

19.05 (3/4) 24.0

When using conventional ﬂ are tools to ﬂ are R32 pipes, the dimension A should be approx-

imately 0.5 mm more than indicated in the table (for ﬂ aring with R32 ﬂ are tools) to achieve

the speciﬁ ed ﬂ aring. Use a thickness gauge to measure the dimension A.

Width across

flats

Pipe outside diameter [mm (in.)]

Width across flats of Flare

nut [mm]

6.35 (1/4) 17

9.52 (3/8) 22

12.70 (1/2) 26

15.88 (5/8) 29

19.05 (3/4) 36

NOTES: The ﬂ are nut speciﬁ cation is compliant with ISO14903.

■

Bending pipes

CAUTION

• To prevent breaking of the pipe, avoid sharp bends.

• If the pipe is bent repeatedly at the same place, it will break.

• The pipes are shaped by your hands. Be careful not to collapse them.

• Bend R70 mm or more with a pipe bender.

• Do not bend the pipes in an angle more than 90°.

• When pipes are repeatedly bend or stretched, the material will harden, making it difﬁ cult

to bend or stretch them anymore.

• Do not bend or stretch the pipes more than 3 times.

• When bending the pipe, do not bend it as

is. The pipe will be collapsed. In this case,

cut the insulating pipe with a sharp cutter

as shown on the right, and bend it after

exposing the pipe. After bending the pipe

as you want, be sure to put the heat insu-

lating pipe back on the pipe, and secure it

with tape.

Pipe

Insulating

pipe

Cutter

Cut line

■

Flare connection

CAUTION

• Be sure to install the pipe against the port on the indoor unit correctly. If the center-

ing is improper, the ﬂ are nut cannot be tightened smoothly. If the ﬂ are nut is forced

to turn, the threads will be damaged.

• Do not remove the ﬂ are nut from the indoor unit pipe until immediately before con-

necting the connection pipe.

• Hold the torque wrench at its grip, keeping it in the right angle with the pipe, in order

to tighten the ﬂ are nut correctly.

• Tighten the ﬂ are nuts with a torque wrench using the speciﬁ ed tightening method.

Otherwise, the ﬂ are nuts could break after a prolonged period, causing refrigerant to

leak and generate hazardous gas if the refrigerant comes into contact with a ﬂ ame.

• Connect the piping so that the control box cover can easily be removed for servic-

ing when necessary.

• In order to prevent water from leaking into the control box, make sure that the pip-

ing is well insulated.

When the flare nut is tightened properly by your hand, hold the body side coupling with

a wrench, then tighten with a torque wrench. (Refer to the following table for the flare nut

tightening torques.)

Tighten with 2 wrenches.

Holding wrench

Flare nut

Connection pipe

Torque wrench

Indoor unit pipe

(Body side)

Flare nut [mm (in.)] Tightening torque [N·m (kgf·cm)]

6.35 (1/4) dia. 16 to 18 (160 to 180)

9.52 (3/8) dia. 32 to 42 (320 to 420)

12.70 (1/2) dia. 49 to 61 (490 to 610)

15.88 (5/8) dia. 63 to 75 (630 to 750)

19.05 (3/4) dia. 90 to 110 (900 to 1,100)

Do not remove the cap from the connection pipe before connecting the pipe.

En-10

3.6. Electrical wiring

WARNING

• Electrical work must be performed in accordance with this Manual by a person certiﬁ ed

under the national or regional regulations. Be sure to use a dedicated circuit for the

unit. An insufﬁ cient power supply circuit or improperly performed electrical work can

cause serious accidents such as electric shock or ﬁ re.

• Before starting work, check that power is not being supplied to the indoor unit and

outdoor unit.

• For wiring, use the prescribed type of cables, connect them securely, making sure

that there are no external forces of the cables applied to the terminal connections.

Improperly connected or secured cables can cause serious accidents such as over-

heating the terminals, electric shock, or ﬁ re.

• Securely install the electrical box cover on the unit. An improperly installed electrical

box cover can cause serious accidents such as electric shock or ﬁ re through exposure

to dust or water.

• Install sleeves into any holes made in the walls for wiring. Otherwise, a short circuit

could result.

• Use the included connection cables and power cables or ones speciﬁ ed by the

manufacturer. Improper connections, insufﬁ cient insulation, or exceeding the allowable

current can cause electric shock or ﬁ re.

• Do not modify the power cables, use extension cables, or use any branches in the

wiring. Improper connections, insufﬁ cient insulation, or exceeding the allowable current

can cause electric shock or ﬁ re.

• Match the terminal block numbers and connection cable colors with those of the

outdoor unit or branch box. Erroneous wiring may cause burning of the electric parts.

• Securely connect the connection cables to the terminal board. In addition, secure the

cables with wiring holders. Improper connections, either in the wiring or at the ends

of the wiring, can cause a malfunction, electric shock, or ﬁ re.

• Always fasten the outside covering of the connection cable with the cable clamp. (If

the insulator is chafed, electric leakage may occur.)

• Install an earth leakage breaker. In addition, install the earth leakage breaker so

that the entire AC main power supply is cut off at the same time. Otherwise, electric

shock or ﬁ re could result.

• Always connect the earth (ground) cable. Improper earthing (grounding) work can

cause electric shocks.

• Perform wiring work in accordance with standards so that the air conditioner can be

operated safely and positively.

• Connect the connection cable ﬁ rmly to the terminal board. Imperfect installation may

cause a ﬁ re.

• Use ring terminals and tighten the terminal screws to the speciﬁ ed torques, otherwise,

abnormal overheating may be produced and possibly cause heavy damage inside

the unit.

CAUTION

• Be careful not to generate a spark as follows for using a ﬂ ammable refrigerant.

- Do not remove the fuse while the power is on.

- Do not disconnect the wiring while the power is on.

- It is recommended to position the outlet connection in a high position. Place the

cords so that they do not get tangled.

• Earth (Ground) the unit. Do not connect the earth (ground) cable to a gas pipe, water

pipe, lightning rod, or a telephone earth (ground) cable. Improper earthing (ground-

ing) may cause electric shock.

• Install the remote controller cables so as not to be direct touched with your hand.

• Do not connect power supply cables to the transmission or remote controller termi-

nals, as this will damage the product.

• Never bundle the power supply cable and transmission cable, remote controller

cable together. Separate these cable by 50 mm or more. Bundling these cables

together will cause miss operation or breakdown.

• When handling PCB, static electricity charged in the body may cause malfunction of

the PCB. Follow the cautions below:

- Establish an earth (a ground) for the indoor and outdoor units and peripheral

devices.

- Cut power (breaker) off.

- Touch metal part of the indoor and outdoor units for more than 10 seconds to

discharge static electricity charged in the body.

- Do not touch terminals of parts and patterns implemented on PCB.

• Be sure to refer to the above diagram for do correct ﬁ eld wiring. Wrong wiring causes

malfunction of the unit.

• Check local electrical rules and also any speciﬁ c wiring instructions or limitation.

3.6.1. Wiring system diagram

■

Standard pair

Indoor unit

Remote

controller cable

Remote

controller cable

*Earth (Ground) the remote controller if it has a earth (ground) line.

Red

White

Black

Wired remote controller

Earth (Ground) line

Outdoor unit

Power line

Control line

Connection cable

2-wire type

3-wire type

Wired remote controller cable

■

Flexible multi

Indoor unit Outdoor unit

Indoor unit

Red

White

Black

Earth (Ground) line

Control line

Connection cable

2-wire type

3-wire type

Wired remote controller cable

Power line

Indoor unit

Remote controller cable

*Earth (Ground) the remote controller if it has a earth ground) line.

Wired remote controller

UNIT A

UNIT B

En-11

■

Simultaneous twin (18 model only)

Connection cable

Indoor unit

(Primary)

Outdoor unit

Indoor unit

(Primary)

Indoor unit

(Secondary)

Indoor unit

(Secondary)

Junction box (Locally purchased)

Earth (Ground) line

Control line

Power line

Earth (Ground) line

Wired remote controller cable

3-wire type only

Wired remote controller

Remote controller cable

Bus wire (Locally purchased,

remote controller cable)

Max length: 500 m

Red

White

Black

*Earth (Ground) the remote controller if it has a earth (ground) line.

• Connect the remote controller wires to the primary unit.

■

Simultaneous triple (18 model only)

Wired remote controller cable

3-wire type only

Connection cable

Indoor unit

(Primary)

Indoor unit

(Secondary)

Outdoor unit

Earth (Ground) line

Control line

Power line

Wired remote controller

Remote controller cable

Bus wire (Locally purchased,

remote controller cable)

Max length: 500 m

Junction box (Locally purchased)

Earth (Ground) line

Red

White

Black

Indoor unit

(Secondary)

Indoor unit

(Primary)

Indoor unit

(Secondary)

Indoor unit

(Secondary)

*Earth (Ground) the remote controller if it has a earth (ground) line.

• Connect the remote controller wires to the primary unit.

Wired remote controller is recommended using simultaneous twin or triple connection.

En-12

3.6.2. Connection cable preparation

■

Connection cable

Keep the earth (ground) wire longer than the other wires.

Connection cable

20 mm

30mm or more

Earth (Ground)

wire

• Use a 4-core wire cable.

■

Remote controller cable

For 2-wire type

For 3-wire type

30 mm 30 mm

3.6.3. How to connect wiring to the terminals

■

Caution when wiring cable

To strip off the insulation of a lead wire, always use a special tool such as a wire stripper.

If there is no special tool, carefully strip off the insulation by using a knife or other utensil.

(1) Use ring terminals with insulating sleeves as shown in the ﬁ gure to connect to the

terminal block.

(2) Securely clamp the ring terminals to the wires by using an appropriate tool so that the

wires do not come loose.

Strip : 10 mm

Ring terminal

Sleeve

(3) Connect speciﬁ ed wires securely, and fasten them so that there is no stress applied on

the terminals.

(4) Use a screwdriver with an appropriate bit size to tighten the terminal screws. Using of

screwdriver with inappropriate bit size will damage the screw heads, and the screws

will not be tightened properly.

(5) Do not overtighten the terminal screws. Otherwise, the screws may break.

Screw with special washer

Wire

Ring terminal

Terminal blocks

Wire

Screw with special washer

Ring terminal

(6) Refer to the table for the terminal screw tightening torques.

(7) Please do not ﬁ x 2 power supply cables with 1 screw.

Tightening torque [N·m (kgf·cm)]

M4 screw 1.2 to 1.8 (12 to 18)

3.6.4. Connection wiring

CAUTION

• Be careful not to mistake the power supply cable and connection wires when install-

ing.

• Install so that the wires for the remote controller will not come in contact with other

connection wires.

(1) Remove the control box cover

(2) Connect the connection cable.

Cover

Screw

■

Connection cable

Y1 Y2

TO REMOTE CONTROL UNIT Ex IN

Y3 1 2 Y1 Y2

TO REMOTE CONTROL UNIT Ex IN

Y3 1 2

12 3

Control line

Connection cable

(power supply)

Power line

Outdoor

unit

Earth (ground)

DIP switch

Print circuit board

(PCB)

2-wire type

White

Red

Remote

controller

cable

Remote controller

Factory setting “2 WIRE”

3-wire type

Black

White

Red

Remote

controller

cable

Remote controller

Set to “3 WIRE”

EarthEarth

Connecting the

Optional parts

■

Remote controller cable

*Earth (Ground) the remote controller if it has a earth (ground) wire.

NOTES: Be sure to change the DIP SW to the corresponding remote controller.

When a 2-wire remote controller is connected to a “3WIRE” setting, power will

not be supplied.

When a 3-wire remote controller is connected to a “2WIRE” setting, a

communication error will be detected.

(3) After wiring is complete, secure the remote controller cable, connection cable with

the cable clamps.

Y1 Y2

TO REMOTE CONTROL UNIT Ex IN

Y3 1 2

12 3

Connection cable

(power supply)

Remote controller

cable

Cable clamp

Cable tie

(medium, accessories)

Avoid covering the air

inlet with the wiring.

Avoid touching the ceiling

with the wiring

Ceiling

Connection cable

(power supply)

Do not bind the power supply cable and other cables together.

En-13

(4) Seal the cable outlet or other gaps with putty to prevent dew condensation or insect

from entering the electric control box.

(5) Replace the control box cover.

CAUTION

Do not bundle the remote controller cable, or wire the remote controller cable in par-

allel, with the indoor unit connection wire (to the outdoor unit) and the power supply

cable. It may cause erroneous operation.

3.7. Remote controller setting

To install and set the remote controller, refer to the installation manual of the remote

controller.

4. OPTIONAL INSTALLATION WORK

4.1. Optional kit installation

WARNING

Regulation of cable differs from each locality, refer in accordance with local rules.

Y1 Y2

TO REMOTE CONTROL UNIT Ex IN

Y3 1 2

12 3

CN65

CN11

CN47

CN48

CN8

This air conditioner can be connected with the following optional kits.

For details on how to install optional parts, refer to the installation manual included in each

item.

Connector No. Option type

CN47*1 Connect wire (UTY-XWZXZG)

CN8 Remote sensor (UTY-XSZX)

CN48 IR Receiver (UTY-LBTM)

CN11 Auto louver grille (UTD-GXT-W)

CN65*2 Other optional parts

*1: For external output terminal setting, refer to Function No.60 in “6. FUNCTION SET-

TING”.

*2: Other options (WLAN adapter, converters, etc.) may be connectable. Please refer to

the technical data for details.

NOTES:

Options connecting to CN65 cannot be used at the same time.

4.2. External input and output

4.2.1. External input

• Indoor unit functions such as Operation/Stop or Forced stop can be done by using

indoor unit terminals.

• “Operation/Stop” mode or “Forced stop” mode can be selected with function setting of

indoor unit.

•

A twisted pair cable (22 AWG) should be used. Maximum length of cable is 150 m (492 ft.).

• Use an external input and output cable with appropriate external dimension, depending

on the number of cables to be installed.

• The wire connection should be separate from the power cable line.

Y1 Y2

TO REMOTE CONTROL UNIT Ex IN

Y3 1 2

Connected device

Terminal

● Dry contact terminal

When a power supply is unnecessary at the input device you want to connect, use the Dry

contact terminal.

Terminal

(External in)

Connected device

*1: The switch can be used on the following condition: DC 12 V to 24 V, 1 mA to 15 mA.

■

Operation behavior

● Input signal type

Edge

OFF

When function setting is “Operation/Stop” mode 1.

Input signal Command

OFF → ON Operation

ON → OFF Stop

When function setting is “Forced stop” mode.

Input signal Command

OFF → ON Forced stop

ON → OFF Normal

* When the forced stop is triggered, indoor unit stops and Operation/Stop operation by a

remote controller is restricted.

When function setting is “Operation/Stop” mode 2.

Input signal Command

OFF → ON Operation

ON → OFF Stop (R.C. disabled)

4.2.2. External output

• A twisted pair cable (22AWG) should be used. Maximum length of cable is 25 m (82 ft.).

• Use an external input and output cable with appropriate external dimension, depending

on the number of cables to be installed.

• Output voltage: Hi DC12V±2V, Lo 0V.

• Permissible current: 50mA

■

Output select

When interlocking with external device

CN47

PCB

Connected

device

Relay (locally purchased)

When displaying “Operation/Stop”

CN47

PCB

Connected device

Resistor

LED

En-14

■Operation behavior

*If function setting “60” is set to “00”

Function setting Status Output voltage

Stop 0V

Operation DC 12 V

Normal 0V

Error DC 12 V

Indoor unit fan stop 0V

Indoor unit fan operation DC 12 V

External heater OFF 0 V

External heater ON DC 12V

4.2.3. Connection methods

■

Wire modiﬁ cation

• Remove insulation from wire attached to wire kit connector.

• Remove insulation from locally purchased cable. Use crimp type insulated butt

connector to join ﬁ eld cable and wire kit wire.

• Connect the wire with connecting wire with solder.

IMPORTANT:

Be sure to insulate the connection between the wires.

Locally purchased

Option parts

External output wire

Solder and insulate the connected parts.

• Connecting wires to the terminals.

Use ring terminals with insulating sleeves to connect to the terminal block.

• Connection terminals and wiring arrangement (Refer to “4.6. Other optional parts”)

4.3. Remote sensor (Optional parts)

4.3.1. Connection method

• Remove the existing connector and replace it with the remote sensor connector (ensure

that the correct connector is used).

• The original connector should be insulated to ensure that it does not come into contact

with other electrical circuitry.

• Connection terminals and wiring arrangement. (Refer to “4.6. Other optional parts”)

4.3.2. Setting for room temperature correction

When a remote sensor is connected, set the function setting of indoor unit as indicated

below.

• Function Number “30”:

Set the Setting Number to “00”. (Default)

• Function Number “31”:

Set the Setting Number to “02”.

* Refer to “6. FUNCTION SETTING” for details about Function number and Setting

value

4.4. IR receiver unit (Optional parts)

• For the installation method, please refer to the installation manual of IR receiver unit.

4.4.1. Connection method

• Use 7 pins for receiver unit cable.

• At ﬁ rst, connect the receiver unit cable to the controller PCB.

• Attach the core that comes between controller PCB and the clamp.

• Connection terminals and wiring arrangement. (Refer to “4.6. Other optional parts”).

4.5. Auto louver grille (Optional parts)

4.5.1. Connection method

• Wiring arrangement

Y1 Y2

TO REMOTE CONTROL UNIT Ex IN

Y3 1 2

12 3

CN11

Controller PCB

DIP SW 101

( " 2 " : ON)



CAUTION

To protect the cable insulation after opening a knockout hole, remove any burrs from

the edge of the hole.

(b) Bushing

(accessories of

optional parts)

Cable tie

(medium, accessories)

Auto louver grille cable

(accessories)

(a) Opening this

knockout hole

4.6. Other optional parts

4.6.1. Connection method

• Connection terminals and wiring arrangement

In following ﬁ gure, all the possible connections are done for description.

In actual installation, connections will differ according to each installation requirements.

Y1 Y2

TO REMOTE CONTROL UNIT Ex IN

Y3 1 2

12 3

CN8

CN65

CN47

CN48

Controller PCB

External output

External input

Core

En-15

4.7. Optional parts cable binding

Auto louver grille cable

Remote controller

cable

Other optional parts cables

Power supply cable

Avoid touching the ceiling with the wirings.

* Use an accessory of indoor unit or optional parts for cable tie.

** Use an accessory of optional parts for bushing.

Ceiling

Cable tie

(medium,

accessories)

Avoid covering the air

inlet with the wirings.

Air inlet

Bushing**

Insulation

• Do not bind the power supply cable and other cables together.

CAUTION

To protect the cable insulation after opening a knockout hole, remove any burrs from

the edge of the hole.

5. REMOTE CONTROL INSTALLATION

5.1. Group control

NOTES: Group control cannot be used together with W-LAN adapter.

A number of indoor units can be operated at the same time using a single remote controller.

*When different types of indoor units (such as wall mounted type and cassette type, cas-

sette type and duct type, or other combinations) are connected using group control sys-

tem, some functions may no longer be available.

(1) Connect up to 16 indoor units in a system.

BCDE

I.U. I.U. I.U. I.U.

Remote

controller

A, B, C, D, E : Remote controller cable.

A+B+C+D+E ≤ 500 m.

Example of wiring method (2-wire type)

123 123 123 123

123

1 Y2

Indoor unit 1 Indoor unit 2 Indoor unit 3 Indoor unit 4

Remote controller cable

Remote con-

troller cable

Remote controller

(2) Set the R.C. address (DIP switch setting)

Set the R.C. address of each indoor unit using the DIP switch on the indoor unit

circuit board.

Y1 Y2

TO REMOTE CONTROL UNIT Ex IN

Y3 1 2

12 3

SW100

(a) 2-wire type

DIP switch (RC AD SW)...Factory setting “00”

Since the remote controller address settings are automatically conﬁ gured, you do not

need to conﬁ gure them.

If conﬁ guring manually, it is necessary to conﬁ gure both the indoor unit and the remote

controller. For details, please refer to the remote controller installation manual.

(b) 3-wire type

DIP switch (RC AD SW)...Factory setting “00”

When connecting multiple indoor units to 1 standard wired remote controller, set the

address at RC AD SW in sequence from “00”.

Setting

range

Switch 100

Remote controller

address

00 to 15

Setting

example 00

1234

RC AD

Example

If 4 indoor units are connected.

RC AD SW

Indoor unit 1

Remote

controller

Indoor unit 2 Indoor unit 3 Indoor unit 4

Set the R.C. address in accordance with the table below.

Indoor unit

R.C. address

DIP SWITCH No.

1234

1 00 OFF OFF OFF OFF

2 01 ON OFF OFF OFF

3 02 OFF ON OFF OFF

4 03 ON ON OFF OFF

5 04 OFF OFF ON OFF

6 05 ON OFF ON OFF

7 06 OFF ON ON OFF

8 07 ON ON ON OFF

9 08 OFF OFF OFF ON

10 09 ON OFF OFF ON

11 10 OFF ON OFF ON

12 11 ON ON OFF ON

13 12 OFF OFF ON ON

14 13 ON OFF ON ON

15 14 OFF ON ON ON

16 15 ON ON ON ON

NOTES:

Be sure to set consecutive R.C. address.

The indoor units cannot be operated if a number is skipped.

00 01 02 03

R.C. address

(DIP switch setting)

Remote

controller

: Transmission cable, Power supply cable

: Connection cable

: Remote controller cable

Outdoor

unit 1

Indoor

unit 1

Indoor

unit 2

Indoor

unit 3

Indoor

unit 4

Outdoor

unit 2

Outdoor

unit 3

Outdoor

unit 4

En-16

■

Settings when simultaneous Multi is included

(3) Set the refrigerant circuit address (Remote controller setting)

1. Turn on all of the indoor units.

* Turn on the indoor unit with the R.C. address 00 last.

(Within 1 minute)

2. Set the refrigerant circuit address.

Assign the same number to all of the indoor units connected to an outdoor unit.

(The unit is factory-set to “00”)

Refrigerant circuit address

Function

Number

Setting Value

02 00 to 15

(4) Set the “primary” and “secondary” settings. (Remote controller setting)

(Set the indoor unit that is connected to the outdoor unit using a transmission cable as the

“primary”.)

Function Number

Setting Value

Primary

Secondary 01

After completing the function settings, turn off all of the indoor units,

and then turn them back on.

* If error code 21, 22, 24, or 27 is displayed, there may be an incorrect

setting. Perform the remote controller setting again.

NOTES:

• When different indoor unit models are connected using the group control system, some

functions may no longer be available.

• If the group control system contains multiple units that are operated simultaneously, con-

nect and set the units as shown below.

• Auto-changeover operates under the same mode with model R.C. address 00.

• It should not be connected to any other Gr that is not of the same series (A**G only).

R.C. address

Standard

pair

Standard

pair

Simultaneous

twin

Simultaneous

triple

Refrigerant circuit

address setting

Primary/Secondary setting

(DIP switch setting)

(Function number 02)

(Function number 51)

Remote

controller

: Transmission cable, Power supply cable

: Power supply cable

: Connection cable

: Remote controller cable

Outdoor

unit 1

Outdoor

unit 2

Outdoor

unit 3

Outdoor

unit 4

Indoor

unit 1

Indoor

unit 2

Indoor

unit 3

Indoor

unit 4

Indoor

unit 5

Indoor

unit 6

Indoor

unit 7

5.2. Multiple remote control

Up to 2 remote controllers can be used to operate one indoor unit

CAUTION

Multiple installation method described above is prohibited to combine 3 Wired type

with 2 Wired Type.

I.U.

Primary Primary Secondary

A, B : Remote controller cable. (Refer to “2.4. Electrical requirement”)

A ≤ 500 m, A+B ≤ 500 m

•

The timer and self-diagnosis functions cannot be used on the secondary units.

(1) Wiring method (indoor unit to remote controller)

Remote con-

troller cable

Indoor unit

Remote controller

Secondary unit

Primary unit

(2) Remote controller DIP switch 1 setting

Set the remote controller DIP switch 1 No. 2 according to the following table.

DIP SW 1-No. 2

Primary unit

OFF

Secondary unit

5.3. DIP switch 101 setting

If contained drain pump is not used, set the drainage function to “Disable” in the drainage

function switching.

The auto louver grille setting (optional parts) can be used when the it is mounted.

For the setting method, refer to “4.5. Auto louver grille (Optional parts)”.

The fan delay setting can be used when the auxiliary heater is mounted.

When the operation is stopped when the indoor unit is operating with an auxiliary heater,

the operation continues 1 minutes.

Change the following settings by using the DIP switch.

(♦... Factory setting)

DIP switch 101

DIP SW state

Details

ON OFF

1 Disable Enable ♦ Drainage function setting

2 Enable Disable ♦ Auto louver grille setting

3 Enable Disable ♦ Fan delay setting

● Switching position

Y1 Y2

TO REMOTE CONTROL UNIT Ex IN

Y3 1 2

12 3

DIP SW 101

En-17

5.4. Simultaneous multi-system operation

CAUTION

• When setting DIP switches, do not touch any other parts on the circuit board directly

with your bare hands.

• Be sure to turn off the main power.

• Ensure to use a 3-wire type wired remote controller. (Set the DIP switch to 3-wire type.)

• When using a simultaneous multi system, a WLAN adapter cannot be used.

• If connected to an indoor unit that supports R410A, an error message is displayed. Check

the machine type of the indoor unit to connect, and ensure to use an indoor unit support-

ing R32.

• By combining with an outdoor unit, 2 units for twin and 3 units for triple indoor units, can

be switched on/off simultaneously.

(1) Wiring method

• Refer to “3.6. Electrical wiring” for wiring procedure and wiring method.

• The indoor unit is connected the outdoor unit using a transmission cable is “primary”.

• Connect the remote controller wire to the primary unit.

■

Twin type ( 18 model only )

Outdoor

unit

Indoor

unit 1

Indoor

unit 2

Remote

controller

[Primary]

[Secondary]

■

Triple type ( 18 model only )

Outdoor

unit

Remote

controller

: Transmission cable, Power supply cable

: Power supply cable

: connection cable: Remote controller cable

Indoor

unit 1

[Primary]

Indoor

unit 2

[Secondary]

Indoor

unit 3

[Secondary]

(2) Set the R.C. address (DIP switch setting )

Set the R.C. address of each indoor unit using the DIP switches on the indoor unit

circuit board. (Refer to the following table and ﬁ gure.)

The DIP switches are normally set to make the R.C. address 00.

Indoor unit R.C. address DIP SWITCH No.

1234

1 00 OFF OFF OFF OFF

2 01 ON OFF OFF OFF

3 02 OFF ON OFF OFF

Y1 Y2

TO REMOTE CONTROL UNIT Ex IN

Y3 1 2

12 3

SW100

NOTES:

Be sure to set the R.C. address sequentially.

(3) Set the primary and secondary (Remote controller setting)

1. Turn on all of the indoor units.

2. Set the “primary” and “secondary” settings.

(Set the indoor unit that is connected to the outdoor unit using a transmission cable

as the “primary”.)

Function Number

Setting Value

Primary

Secondary 01

3. After completing the function settings, turn off all of the indoor units, and then turn

them back on.

* If error code 21, 22, 24 or 27 is displayed, there may be an incorrect setting.

Perform the remote controller setting again.

■

Twin type ( 18 model only )

R.C. address

Primary/Secondary setting

(DIP switch setting)

(Function number 51)

Outdoor

unit

Remote

controller

Indoor

unit 1

[Primary]

Indoor

unit 2

[Secondary]

■

Triple type ( 18 model only )

R.C. address

Primary/Secondary setting

(DIP switch setting)

(Function number 51)

Outdoor

unit

Remote

controller

: Transmission cable, Power supply cable

: Power supply cable

: Connection cable

: Remote controller cable

Indoor

unit 1

[Primary]

Indoor

unit 2

[Secondary]

Indoor

unit 3

[Secondary]

6. FUNCTION SETTING

6.1. Function details

■

Filter sign

Select appropriate intervals for displaying the ﬁ lter sign on the indoor unit according to the

estimated amount of dust in the air of the room.

If the indication is not required, select “No indication” (03).

(♦... Factory setting)

Function

number

Setting

value

Setting description

00 Standard (400 hours)

01 Long interval (1000 hours)

02 Short interval (200 hours)

03 No indication ♦

■

Static pressure

Select appropriate static pressure according to the installation conditions.

(♦... Factory setting

)

Function

number

Setting

value

Setting description

00 0 Pa

01 10 Pa

02 20 Pa

03 30 Pa

04 40 Pa

05 50 Pa

06 60 Pa

07 70 Pa

08 80 Pa

09 90 Pa

31 ♦ 25 Pa [Standard]

Range of static pressure is different from 1 model to other.

Range of static pressure 0 to 90 Pa

En-18

■

Room temperature control for indoor unit sensor

Depending on the installed environment, correction of the room temperature sensor may

be required.

Select the appropriate control setting according to the installed environment.

The temperature correction values show the difference from the “Standard setting” (00)

(manufacturer’s recommended value).

(♦... Factory setting)

Function number

Setting

value

Setting description

(For cooling)

(For heating)

00 Standard setting ♦

01 No correction 0.0 °C (0 °F)

02 -0.5 °C (-1 °F)

Cooling

Less

Heating

03 -1.0 °C (-2 °F)

04 -1.5 °C (-3 °F)

05 -2.0 °C (-4 °F)

06 -2.5 °C (-5 °F)

07 -3.0 °C (-6 °F)

08 -3.5 °C (-7 °F)

09 -4.0 °C (-8 °F)

10 +0.5 °C (+1 °F)

Less

Cooling

Heating

11 +1.0 °C (+2 °F)

12 +1.5 °C (+3 °F)

13 +2.0 °C (+4 °F)

14 +2.5 °C (+5 °F)

15 +3.0 °C (+6 °F)

16 +3.5 °C (+7 °F)

17 +4.0 °C (+8 °F)

■

Room temperature control for wired remote controller sensor

Depending on the installed environment, correction of the wire remote temperature sensor

may be required.

Select the appropriate control setting according to the installed environment.

To change this setting, set Function 42 to “Both” (01).

Ensure that the Thermo Sensor icon is displayed on the remote controller screen.

(♦... Factory setting)

Function number

Setting

value

Setting description

(For cooling)

(For heating)

00 No correction ♦

01 No correction 0.0 °C (0 °F)

02 -0.5 °C (-1 °F)

Cooling

Less

Heating

03 -1.0 °C (-2 °F)

04 -1.5 °C (-3 °F)

05 -2.0 °C (-4 °F)

06 -2.5 °C (-5 °F)

07 -3.0 °C (-6 °F)

08 -3.5 °C (-7 °F)

09 -4.0 °C (-8 °F)

10 +0.5 °C (+1 °F)

Less

Cooling

Heating

11 +1.0 °C (+2 °F)

12 +1.5 °C (+3 °F)

13 +2.0 °C (+4 °F)

14 +2.5 °C (+5 °F)

15 +3.0 °C (+6 °F)

16 +3.5 °C (+7 °F)

17 +4.0 °C (+8 °F)

■

Auto restart

Enable or disable automatic restart after a power interruption.

(♦... Factory setting)

Function

number

Setting

value

Setting description

00 Enable ♦

01 Disable

* Auto restart is an emergency function such as for power outage etc. Do not attempt to

use this function in normal operation. Be sure to operate the unit by remote controller or

external device.

■

Room temperature sensor switching

(Only for wireless remote controller)

When using the Wired remote controller temperature sensor, change the setting to “Both” (01).

(♦... Factory setting)

Function

number

Setting

value

Setting description

00 Indoor unit ♦

01 Both

00: Sensor on the indoor unit is active.

01: Sensors on both indoor unit and wired remote controller are active.

Remote controller sensor must be turned on by using the remote controller

■

Remote controller custom code

(Only for wireless remote controller)

The indoor unit custom code can be changed. Select the appropriate custom code.

(♦... Factory setting)

Function

number

Setting

value

Setting description

00 A ♦

01 B

02 C

03 D

■

External input control

“Operation/Stop” mode or “Forced stop” mode can be selected.

(♦... Factory setting)

Function

number

Setting

value

Setting description

00 Operation/Stop mode 1 ♦

01 (Setting prohibited)

02 Forced stop mode

03 Operation/Stop mode 2

■

Room temperature sensor switching (Aux.)

To use the temperature sensor on the wired remote controller only, change the setting to “Wired

remote controller” (01). This function will only work if the function setting 42 is set at “Both” (01)

(♦... Factory setting)

Function

number

Setting

value

Setting description

00 Both ♦

01 Wired remote controller

■

Indoor unit fan control for energy saving for cooling

Enables or disables the power-saving function by controlling the indoor unit fan rotation when

the outdoor unit is stopped during cooling operation.

(♦... Factory setting)

Function

number

Setting

value

Setting description

00 Disable

01 Enable

02 Remote controller ♦

00: When the outdoor unit is stopped, the indoor unit fan operates continuously following

the setting on the remote controller.

01: When the outdoor unit is stopped, the indoor unit fan operates intermittently at a very

low speed.

02: Enable or disable this function by remote controller setting.

*When using a wired remote controller without Indoor unit fan control for energy saving for

cooling function, or when connecting a single split converter, the setting cannot be made

by using the remote controller. Set to (00) or (01).

To conﬁ rm if the remote controller has this function, refer to the operating manual of each

remote controller.

■

Switching functions for external output terminal

Functions of the external output terminal can be switched.

(♦... Factory setting)

Function

number

Setting

value

Setting description

00 Operation status ♦

01 to 08 (Setting prohibited)

09 Error status

10 Fresh air control

11 Auxiliary heater

■

Setting record

Record any changes to the settings in the following table.

Setting description Setting value

Filter sign

Static pressure

Room temperature control for indoor

unit sensor

Cooling

Heating

Room temperature control for

wired remote controller sensor

Cooling

Heating

Auto restart

Room temperature sensor switching

Remote controller custom code

External input control

Room temperature sensor switching (Aux.)

Indoor unit fan control for energy saving for cooling

Switching functions for external output terminal

After completing the Function Setting, be sure to turn off the power and turn it on again.

En-19

7. TEST RUN

7.1. Check items

□ Is operation of each button on the remote controller normal?

□ Does each lamp light normally?

□ Is the drain normal?

□ Do not have an abnormal noise and vibration during operation?

Do not operate the air conditioner in test run for a long time.

7.2. Operation method

Depending on your installation, choose from the following:

■

By the wireless remote controller (with [TEST RUN] button)

(1) To start test run, press [START/STOP] and [TEST RUN] on the remote controller.

(2) To end test run, press [START/STOP] on the remote controller.

■

By the indoor unit or IR receiver unit

(1) To start test run, press [MANUAL AUTO] of the unit for more than 10 seconds (forced

cooling).

(2) T

o end test run, press [MANUAL AUTO] for more than 3 seconds or press [START/STOP]

on the remote controller.



The Operation indicator lamp and Timer indicator lamp will simultaneously ﬂ ash during

the test run mode.

■

By the wired remote controller

(1) For the operation method, refer to the installation manual and the operating manual of

the wired remote controller.

Heating test run will begin in a few minutes when HEAT is selected by the remote control-

ler [reverse cycle model only].

8. FINISHING

Install the heat insulation material after performing a refrigerant leak check (Refer to the

Installation manual for the outdoor unit for details).

■

Coupler heat insulation

CAUTION

• After checking for gas leaks (refer to the Installation Manual of the outdoor unit),

perform this section.

• Install heat insulation around both the large (gas) and small (liquid) pipes. Failure to

do so may cause water leaks.

• Insulate with the coupler heat insulation (accessories) around the gas pipe and liquid

pipe at indoor unit.

• After installing the coupler heat insulation, wrap both ends with vinyl tape so that

there is no gap.

• After afﬁ xing the coupler heat insulation, secure it with 2 cable tie (large,

accessories), one on each end of the insulation.

• Make sure that the cable tie overlap the heat insulation pipe.

Coupler heat

insulation

(accessories)

Cover this portion with

heat insulation.

Cable tie

(large, accessories)

Heat insulation

9. CUSTOMER GUIDANCE

Explain the following to the customer in accordance with the operating manual:

(1) Starting and stopping method, operation switching, temperature adjustment, timer, air

ﬂ ow switching, and other remote controller operations.

(2) Cleaning and maintenance of the product, and other items such as air ﬁ lters and air

louvers if applicable.

(3) Give the operating and installation manuals to the customer.

(4) If the indoor unit custom code is changed, and the installation includes a wireless

remote controller, inform the customer the changed code. (On some wireless remote

controllers, the custom code may return to A when batteries are replaced.)

10. ERROR CODES

If you use a wireless remote controller, the lamp on the photo detector unit will output error

codes by way of blinking patterns. If you use a wired remote controller, error codes will ap-

pear on the remote control display. Refer to the lamp blinking patterns and error codes in

the table. An error display is displayed only during operation.

Error display

Error code Description

OPERATION

lamp

(green)

TIMER

lamp

(orange)

ECONOMY

lamp

(green)



(1)



(1)

Serial communication error



(1)



(2)

• Wired remote controller com-

munication error

• Server room control communica-

tion error



(1)



(5)

Check run unfinished

Automatic airflow adjustment error



(1)



(6)

Peripheral unit transmission PCB

connection error



(1)



(8)

External communication error



(2)



(1)

Unit number or Refrigerant

circuit address setting error

[Simultaneous Multi]



(2)



(2)

Indoor unit capacity error



(2)



(3)

Combination error



(2)



(4)

• Connection unit number

error (indoor secondary unit)

[Simultaneous Multi]

• Connection unit number error

(indoor unit or branch unit)

[Flexible Multi]



(2)



(6)

Indoor unit address setting error



(2)



(7)

Primary unit, secondary unit setup

error [Simultaneous Multi]



(2)



(9)

Connection unit number error in

wired remote controller system



(3)



(1)

Power supply interruption error



(3)



(2)

Indoor unit PCB model information

error



(3)



(3)

Indoor unit motor electricity

consumption detection error



(3)



(5)

Manual auto switch error



(3)



(9)

Indoor unit power supply error for

fan motor



(3)



(10)

Indoor unit communication circuit

(wired remote controller) error



(4)



(1)

Room temp. sensor error



(4)



(2)

Indoor unit heat ex. middle temp.

sensor error



(4)



(4)

Human sensor error



(5)



(1)

Indoor unit fan motor error



(5)



(3)

Drain pump error

●

(5)

●

(4)

Electric air cleaner reverse VDD

error

En-20

Error display

Error code Description

OPERATION

lamp

(green)

TIMER

lamp

(orange)

ECONOMY

lamp

(green)

●

(5)

●

(5)

Filter set error



(5)



(7)

Damper error

●

(5)

●

(8)

Intake grille error

●

(5)

●

(9)

Indoor unit fan motor 2 error

(Left side fan)

●

(5)

●

(10)

Indoor unit fan motor 3 error

(Right side fan)



(5)



(15)

Indoor unit error



(6)



(1)

Outdoor unit reverse/missing

phase and wiring error



(6)



(2)

Outdoor unit main PCB

model information error or

communication error



(6)



(3)

Inverter error



(6)



(4)

Active filter error, PFC circuit error



(6)



(5)

Trip terminal L error



(6)



(8)

Outdoor unit rush current limiting

resister temp. rise error



(6)



(10)

Display PCB microcomputers

communication error



(7)



(1)

Discharge temp. sensor error



(7)



(2)

Compressor temp. sensor error



(7)



(3)

Outdoor unit Heat Ex. liquid temp.

sensor error



(7)



(4)

Outdoor temp. sensor error



(7)



(5)

Suction Gas temp. sensor error



(7)



(6)

• 2-way valve temp. sensor error

• 3-way valve temp. sensor error



(7)



(7)

Heat sink temp. sensor error



(8)



(2)

• Sub-cool Heat Ex. gas inlet

temp. sensor error

• Sub-cool Heat Ex. gas outlet

temp. sensor error



(8)



(3)

Liquid pipe temp. sensor error



(8)



(4)

Current sensor error



(8)



(6)

• Discharge pressure sensor error

• Suction pressure sensor error

• High pressure switch error



(9)



(4)

Trip detection

Error display

Error code Description

OPERATION

lamp

(green)

TIMER

lamp

(orange)

ECONOMY

lamp

(green)



(9)



(5)

Compressor rotor position

detection error (permanent stop)



(9)



(7)

Outdoor unit fan motor 1 error



(9)



(8)

Outdoor unit fan motor 2 error



(9)



(9)

4-way valve error



(9)



(10)

Coil (expansion valve) error



(10)



(1)

Discharge temp. error



(10)



(3)

Compressor temp. error



(10)



(4)

High pressure error



(10)



(5)

Low pressure error



(13)



(2)

Branch boxes error

[Flexible Multi]

Display mode

●

: 0.5s ON / 0.5s OFF

◊

: 0.1s ON / 0.1s OFF

( ) : Number of flashing

Fujitsu RDG12KLLAP Installation guide

Brand: Fujitsu

Model: RDG12KLLAP

Type: Installation guide

This manual is also suitable for

Download PDF

report

Fujitsu RDG12KLLAP Installation guide

This manual is also suitable for

Fujitsu RDG12KLLAP Installation guide

Other documents