Digital Watchdog DWC-V7253TIR Installation guide

Brand: Digital Watchdog

Model: DWC-V7253TIR

Type: Installation guide

Digital Watchdog DWC-V7253TIR is an ultra low-profile vandal dome camera that offers high-definition video surveillance with a resolution of 1080p. It features a 2.8-12mm motorized lens that provides a wide field of view and allows for flexible adjustment of the camera's angle. Additionally, this camera comes equipped with built-in infrared LEDs that enable night vision capabilities, making it suitable for 24/7 surveillance. The DWC-V7253TIR also supports multiple signal formats, including HD-TVI, HD-CVI, and HD-Analog, providing compatibility with various surveillance systems.

Quick Start Guide Quick Start Guide

1. The mounting surface must withstand ﬁve times the weight of your

camera.

2. Pay attention to the cables. The can easily become caught and

damaged. Any damage may cause a short or ﬁre.

3. Detach the camera’s dome cover by loosening the three (3) screws on

the dome using the included torque wrench.

4. Use the mounting template to mark and drill the necessary holes in

the mounting surface.

STEP 1 – PREPARING TO MOUNT THE CAMERA

Pass the wires through the mount bracket and make all necessary

connections. Connect the BNC cable and power cables to the

camera.

STEP 2 – CABLING THE CAMERA TO

EXTERNAL DEVICES

Power requirements Power consumption

12VDC O NLY !

CAUTION! The camera supports

DC power supply only

DC12V (LED o): 1.92W

DC12V (LED on): 3.12W

Tel: +1 (866) 446-3595 / (813) 888-9555

Technical Support Hours:

9:00AM – 8:00PM EST, Monday thru Friday

digital-watchdog.com

WHAT’S IN THE BOX

Mounting bolt

and nuts

1 Set

Mounting

templates

Hex Allen

wrench

Quick set up

guide

Screws

and plastic

anchors-2pcs

1 Set

Test video

cable

Protective sheet

Manual

Template Sheet

for installing by Bolt & Nut

Mount Bolt & Nut

Screw &

Plasc Anchor-2pcs

Torx Wrench

Test Video Cable

Manual

Template Sheet

for installing by Bolt & Nut

Mount Bolt & Nut

Screw &

Plasc Anchor-2pcs

Torx Wrench

Test Video Cable

Manual

Template Sheet

for installing by Bolt & Nut

Mount Bolt & Nut

Screw &

Plasc Anchor-2pcs

Torx Wrench

Test Video Cable

Manual

Template Sheet

for installing by Bolt & Nut

Mount Bolt & Nut

Screw &

Plasc Anchor-2pcs

Torx Wrench

Test Video Cable

Manual

Template Sheet

for installing by Bolt & Nut

Mount Bolt & Nut

Screw &

Plasc Anchor-2pcs

Torx Wrench

Test Video Cable

Manual

Template Sheet

for installing by Bolt & Nut

Mount Bolt & Nut

Screw &

Plasc Anchor-2pcs

Torx Wrench

Test Video Cable

Attention: This document is intended to serve as a quick reference for initial

set up. It is recommended that the user read the entire instruction manual for

complete and proper installation and usage.

NOTE: Download all your support materials and tools in one place.

1. Go to: http://www.digital-watchdog.com/resources

2. Search your product by entering the part number in

the ‘Search by Product’ search bar. Results for

applicable part numbers will populate automatically

based on the part number you enter.

3. Click ‘Search’. All supported materials, including manuals

and quick start guide (QSGs) will appear in the results.

DW® Universal HD over Coax®

ultra low-proﬁle vandal dome cameras

DWC-V7253TIR

Mounting template

Protective sheet

Quick Start Guide

1. The camera supports HD-Analog, HD-CVI and HD-TVI signals. To

switch between the signals:

a. Remove the camera’s dome to access the joystick and OSD

control on the base of the camera.

b. Use the OSD Switch to switch the camera’s signal.

1. Once all cables have been connected, use the screws included with

the camera to properly mount and secure the camera to the mounting

surface.

2. Adjust the camera’s pan, tilt and position to achieve the desired view.

The cameras’ max angles are:

Pan: 0° ~ 360°

Tilt: 0° ~ 70°

Rotation: 0° ~ 360°

3. Once the installation is complete, remove the protective ﬁlm from the

camera’s dome cover.

4. The camera has a manual IR switch, located under the camera’s lens.

You can use this switch to manually turn the IR LED board on or o

according to the installation needs.

STEP 4 – INSTALLING THE CAMERASTEP 3 – CHANGING THE SIGNAL IN

THE CAMERA

Rev Date: 08/19

Speciﬁcations and pricing are subject to change without notice.

Mounting template

1. Using the bolt and nut mounting template, mark and drill the

necessary holes in the mounting surface.

2. Pass wires through and make all connections (see STEP 2 for more

information).

3. Secure the two long mounting screws to the camera’s base.

4. Mount the camera to the mounting surface by using the 2 mounting

nuts.

5. Rotate the locking discs over the screws until the camera is held

tightly from the mounting surface.

For a bolt and nut installation:

Rotation 360°

Titling 70°

Panning 360°

On/o

- To switch the camera to

HD-TVI mode, press OSD

joystick to the left

for 5 seconds.

- To switch the camera to

HD-Analog mode, press OSD

joystick to the right

for 5 seconds.

- To switch the camera to CVBS

mode, press OSD joystick up

for 5 seconds.

- To switch the camera to

HD- CVI mode, press OSD

joystick down for 5 seconds.

DOWN

Digital Watchdog DWC-V7253TIR Installation guide

Digital Watchdog DWC-V7253TIR Installation guide

Digital Watchdog DWC-V7253TIR Installation guide

Related papers