Danfoss VLT 6000 (Legacy Product) User guide
- Type
- User guide
Danfoss VLT 6000 (Legacy Product) is a frequency converter that offers precise control of AC motors, enabling variable speed operation and energy savings. Here are some key capabilities:
- Precise speed control for a wide range of applications
- Energy savings through optimized motor operation and reduced mechanical stress
- Built-in protection features to ensure reliable operation and prevent damage to the motor
- Flexible control options, including local keypad, fieldbus communication, and remote I/O
- Compact design for easy installation and space-saving
Danfoss VLT 6000 (Legacy Product) is a frequency converter that offers precise control of AC motors, enabling variable speed operation and energy savings. Here are some key capabilities:
- Precise speed control for a wide range of applications
- Energy savings through optimized motor operation and reduced mechanical stress
- Built-in protection features to ensure reliable operation and prevent damage to the motor
- Flexible control options, including local keypad, fieldbus communication, and remote I/O
- Compact design for easy installation and space-saving
Switching between mains supply and VLT
®
1MN.60.R1.02 - VLT is a registered Danfoss trademark
Switching between mains supply and VLT
®
In certain plants, e.g. pump or ventilation plants, the use of the same motor in two different ways may be
expedient:
A) Connected direct to the mains supply so that the motor is running at a fixed speed.
B) Connected to a frequency converter so that the speed of the motor is variable.
Fig. 1 illustrates how the motor "M1" can be connected either direct to the mains or to a VLT
®
6000
frequency converter:
Switching between mains supply and VLT
®
frequency converter by means of a change-over switch
Switching between mains supply and VLT
®
MN.60.R1.02 - VLT is a registered Danfoss trademark
2
Switching between mains supply and VLT
®
Advantages by switching between mains supply and VLT frequency converter by means of change-over
switch
■ The possibility of switching between mains operation and operation via VLT frequency converter can be
used to increase the reliability of the plant through a redundant system
■ Operating on the mains supply, the motor can yield a very high breakaway torque
The diagram below shows how the switchgear can be made:
Switching between mains supply and VLT
®
3MN.60.R1.02 - VLT is a registered Danfoss trademark
Switching between mains supply and VLT
®
Mains operation
■
Start:Start:
Start:Start:
Start: Turn the switch "S0" from position "0" to position "MAINS”. Then the relay
"K1M” is energized and the motor starts.
■
Stop:Stop:
Stop:Stop:
Stop: Turn the switch "S0" back to position "0". The relay "K1M” drops out and the
motor stops.
Operation via VLT frequency converter
■
Start:Start:
Start:Start:
Start: Turn the switch "S0" to position "VLT”. The relays "K2M” and "K3M”
are energized and the VLT frequency converter will power up and start the motor using
"Flying start”. If the motor may not start, when the drive is powered up, then an additional start
condition must be set, as described in the operating instructions. It is now possible to control the
speed and torque of the motor via the normal control inputs of the frequency converter.
■
Stop:Stop:
Stop:Stop:
Stop: Turn the switch "S0" back to position "0".Then the relays "K2M” and "K3M” fall and the motor
stops.
List of components
■
F1:F1:
F1:F1:
F1: 3 motor fuses
■
F2:F2:
F2:F2:
F2: 3 fuses for the VLT frequency converter. Size A = acording to MG60A202
■
F3:F3:
F3:F3:
F3: 1 control current fuse
■
F4:F4:
F4:F4:
F4: Thermal relay with stop, type CI
■
K1M:K1M:
K1M:K1M:
K1M: Contactor, type CI, with one NC auxiliary contacts
(NC = Normally closed)
■
K2M:K2M:
K2M:K2M:
K2M: Contactor, type CI, with one NC auxiliary contact
■
K3M:K3M:
K3M:K3M:
K3M: Contactor, type CI, with one NC auxiliary contact and a CBNO Code No. 037H0121 (gold plated
NO contact)
(NO = Normally open)
■
S0:S0:
S0:S0:
S0: 1-pole change-over switch with 3 positions
1 mechanical interlock to be placed between "K1M” and "K3M”, to prevent that somebody by hand pushes
down the contacter bridge.
F2 and K2M can be substituded if it is accepted acording to local code of Practicel with a "Circuit Breakers”
type CTI. For further information, see Application notes MN500102.
Further information:
Operating instructions VLT 6000 HVAC Code No. MG.60.AX.YY
Motor Control Gear Code No. IK40T202 and MN.90.KX.YY
X = version number
YY = language version
-
1
-
2
-
3
Danfoss VLT 6000 (Legacy Product) User guide
- Type
- User guide
Danfoss VLT 6000 (Legacy Product) is a frequency converter that offers precise control of AC motors, enabling variable speed operation and energy savings. Here are some key capabilities:
- Precise speed control for a wide range of applications
- Energy savings through optimized motor operation and reduced mechanical stress
- Built-in protection features to ensure reliable operation and prevent damage to the motor
- Flexible control options, including local keypad, fieldbus communication, and remote I/O
- Compact design for easy installation and space-saving
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Related papers
-
Danfoss VLT HVAC Drive FC 102 Installation guide
-
Danfoss VLT Compact Starter MCD 200 User guide
-
-
Danfoss VLT AutomationDrive FC 301 Operating instructions
-
CookTek MCD3000 Specification
-
-
-
-
-
