CMI 192-6439 Installation guide

CMI
Brand
CMI
Model
192-6439
Category
Sanitary ware
Type
Installation guide

CMI 192-6439, a stylish and durable bathroom faucet, offers a wide range of features for an enhanced user experience. With its 3-hole installation design, it fits most standard bathroom sinks and provides a widespread reach for easy accessibility. The faucet's polished chrome finish adds a touch of elegance to your bathroom décor. It comes equipped with a brass pop-up drain and a variety of washers and gaskets for a secure and leak-free installation. Additionally, the faucet includes a flow restrictor to help conserve water without compromising performance.

CMI 192-6439, a stylish and durable bathroom faucet, offers a wide range of features for an enhanced user experience. With its 3-hole installation design, it fits most standard bathroom sinks and provides a widespread reach for easy accessibility. The faucet's polished chrome finish adds a touch of elegance to your bathroom décor. It comes equipped with a brass pop-up drain and a variety of washers and gaskets for a secure and leak-free installation. Additionally, the faucet includes a flow restrictor to help conserve water without compromising performance.

Aegean Wide Spread Bathroom Faucet With
Brass Pop-Up
Model No. : Polished Chrome
192-6438 Brushed Nickel
192-6439 Oil-Rubbed Bronze
192-6437
3 Hole Installation , to 6"-10" Center-Set
Revised 5/2/17
In the event that Freendo faucets are used in a Commercial Application, this warranty is limited for
a period of 5 years, unless otherwise specifically stated in the catalog and/or price book.
repair. Compass Manufacturing International will, at its discretion, provide new or equivalent replacement
parts for any product that proves to be defective under normal usage and service.
Screwdriver
C.A. B.
Warning:The supply valves and supply lines are not included.
Plumber's Putty
Handle
Handle Adapter
O-ring
Cartridge(Hot Water)
Cartridge Seat
O-ring
Brass Valve Body
O-ring
O-ring
Clamp
Locknut
Screw
Spout
Aerator
O-ring
Connect Hose
Clamp
Locknut
Quick Connect Hose
Allen Key
Cartridge(Cold Water)
Plastic Lock Ring
Clip
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
No. Part Name
24
25
26
27
28
29
31
32
30
Flange
Locknut
Drain Body
Lift Rod
Extend Rod
Horizontal Rod
Rod Guide Nut
Top Rubber Washer
Bottom Rubber Washer
Drain Stopper
Washer
Tailpiece
Rod Ball Plastic Gasket
33
34
35
36
37
38
39
40
41
42
43
44
Cartridge Locknut
Base
Extend Rod Screw
Spring Clip
Body
Screw
Screw
No. Part Name
Flow Restricter
Let both hot and cold water run for one minute.
This will help clean any debris that might clog
the system.
and/or Silicone
Faucet Installation
21
27
28
16
1
11
12
13
14
24
1. 2.
3.
1. Position spout 16 and O-ring 21 on countertop, from underneath of the
countertop, assemble clamp 27 and locknut 28 , tighten the locknut with
basin wrench.
2. Position the handle 1 as shown,and assemble the clamp 11 , locknut 12
and screw 13 .Tighten the locknut 12 by hand and secure the screws 13
by screwdriver. Repeat the above steps for the other handle.
3. Position the quick connect hose 24 as shown and fix it to faucet by using
the clip 14 .
33
34
35
36
37
38
39
40
42
43
41
44
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
1
rod guide nut 43rod ball
plastic
gasket 42
drain
stopper
hole
drain
body 39
o-ring
sink
drain stopper 33
flange 34
align hole in
drain stopper
with guide rod
opening
(pointed toward
back wall)
flange 34
drain body 39
top rubber washer 35
sink base
locknut 38
washer 37
bottom
rubber
washer 36
tailpiece 40
faucet
body
A. Remove pop-up drain stopper 33.
and flange 34 with top rubber
washer 35 for pop-up assembly.
B. Insert drain body from underneath
of sink drain hole.Replace flange 34
and top rubber washer 35 back to
drain body 39 .Tighten flange as far
as possible.
C. Slide bottom rubber washer 36
on drain body up against bottom
of sink. Tighten washer 37 and
locknut 38 firmly against base
for tight seal.
D. Remove tailpiece 40 from drain
body 39 ,add Teflon tape,replace
tailpiece 40.
A. Replace pop-up drain stopper 33
to drain body 39 with o-ring
in place, and align stopper hole
with guide rod opening.
A. Remove rod guide nut 43 and
rod ball plastic gasket 42 .
B. Insert horizontal rod 41 into
drain body 39 and through hole
in drain stopper 33 .
C. Replace rod guide nut 43 with
rod ball plastic gasket 42 and
tighten it.
horizontal rod 41
extend rod 31
horizontal rod 41
spring
clip 44
extend rod
hole
extend rod
screw 32
A. Insert lift rod 46 through hole on
faucet body. Connect horizontal
rod 41 to extend rod 31 using
spring clip 44 to hold and adjust.
B. Attach extend rod 31 with
lift rod 30 by inserting lift rod
through extend rod hole. Now
adjust lift rod 30 to correct height
and hand tighten extend rod
screw 32 .
lift rod 30
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4

CMI 192-6439 Installation guide

CMI
Brand
CMI
Model
192-6439
Category
Sanitary ware
Type
Installation guide

CMI 192-6439, a stylish and durable bathroom faucet, offers a wide range of features for an enhanced user experience. With its 3-hole installation design, it fits most standard bathroom sinks and provides a widespread reach for easy accessibility. The faucet's polished chrome finish adds a touch of elegance to your bathroom décor. It comes equipped with a brass pop-up drain and a variety of washers and gaskets for a secure and leak-free installation. Additionally, the faucet includes a flow restrictor to help conserve water without compromising performance.

Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents