1
ADI16-4(FIT)GY
ADI16-4(FIT)GY
First Step Guide
CONTEC CO.,LTD.
Thank you for purchasing the CONTEC product.
This product is a device module of the F&eIT series that converts analog data into digital data to input.
Create a stack connection with our micro controller unit of [CPU-SBxx/xxx(FIT)GY] (xx shows figure)
or I/O controller unit of [CPU-CAxx(FIT)GY] (xx shows figure) to utilize this product.
Check, with the following list, that your package is complete. If you discover damaged or missing items,
contact your retailer.
Product Configuration List
- Module ...1 - First Step Guide (this booklet) …1
- CD-ROM [F&eIT Series Setup Disk] ...1 - Warranty Certificate …1
- Interface connector plug ...1 - Serial number label …1
About a User’s Manual
The User’s Manual of this product is offered as the PDF file in the bundled CD-ROM. With it, since
information such as a setup of hardware, connection (signal arrangement of a connector) with external
devices and product specification is indicated, please refer to it if needed. You can display the User’s
Manual from the boot screen of the bundled CD-ROM.
PDF file storing place:\UsersGuide
Adobe Reader is required in order to read a description.
The reference place of the installation method
Note that the softwares required to use the device module vary depending on the controller to which the
device module is connected.
- If you use the micro controller unit [CPU-SBxx/xxx(FIT)GY]
Information Reference place
Installation by Windows
(Driver : API-SBP(W32))
See below for more information
\APISBP\READMEU.HTML file
- If you use the I/O controller unit [CPU-CAxx(FIT)GY]
Information Reference place
Installation by Windows
(Driver : API-CAP(W32))
See below for more information
\APICAP\READMEU.HTML file
Installation by Linux
(Driver : API-CAP(LNX))
See below for more information
\APICAP\Linux\readmee.txt file
Product information
Visit the CONTEC’s Web site for more information on this product.
Inquiry
Contact your retailer.
ADI16-4(FIT)GY First Step Guide
Copyright 2006 CONTEC CO., LTD. ALL RIGHTS RESERVED.
CONTEC CO., LTD. September 2012 Edition
3-9-31, Himesato, Nishiyodogawa-ku, Osaka 555-0025, Japan
Japanese http://www.contec.co.jp/
English http://www.contec.com/ A-51-185 (LYFU432)
Chinese http://www.contec.com.cn/ 09052012_rev2 [01112006]
No part of this document may be copied or reproduced in any form by any means without prior written
consent of CONTEC CO., LTD.
Handling Precautions
CAUTION
- Do not modify the module. CONTEC will bear no responsibility for any problems, etc., resulting
from modifying this module.
- Do not use or store the module in a hot or cold place, or in a place that is subject to severe
temperature changes.
(Operating temperature range: 0 - 50°C)
- Do not use or store the module in a place subject to direct sunlight or near a heating device, such as
a stove.
- Do not use or store the module in a dusty or humid place.
(Operating humidity range: 10 - 90%RH, No condensation)
- As this module contains precision electronic components, do not use or store it in environments
subject to shock or vibration.
- Do not use or store the module near equipment generating a strong magnetic field or radio waves.
- If you notice any strange odor or overheating, please unplug the power cable immediately.
- In the event of an abnormal condition or malfunction, please consult the dealer from whom the
module was purchased.
- To avoid electric shock, please do not touch the module with a wet hand.
- Do not open the module casing. CONTEC will disclaim any responsibility for module whose casing
has been opened.
- Do not strike or bend the module. Doing so could damage the module.
- To prevent contact malfunction, please do not touch the metallic pins on the external module
connector.
- The module contains switches that need to be properly set. Before using the module, please check
its switch settings.
- To avoid malfunction, please do not change the module switch settings in an unauthorized manner.
- Do not connect the device module to the controller module already energized. To avoid malfunction,
please be sure to turn off the control module before connecting the device module to it.
-
1
-
2
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Related papers
-
Contec ADI12-8(FIT)GY Owner's manual
-
Contec ADI16-4(FIT)GY Owner's manual
-
-
-
Contec DAI16-4(FIT)GY Owner's manual
-
-
-
-
-