INSTRUCTIONS FOR MODELS
92-CPT-3000-R2
For additional assistance or service please contact:
SPEAKMAN
®
Company
400 Anchor Mill Road
New Castle, DE 19720
800-537-2107
customerser[email protected]
www.speakman.com
CPT-3000
TOOLS AND SUPPLIES
Phillips
Screwdriver
Silicone Caulk Gun
Additional warranty information can be found at:
www.speakman.com
WARRANTY
MAINTENANCE
Cover your drain to prevent loss of parts. Be sure to
wear eye protection while cutting pipe.
SAFETY TIPS
IMPORTANT
• Be sure to read instructions thoroughly before
beginning installation.
• Do not over-tighten any connections or damage
may occur.
• This valve has an operating range of 20-80 psi.
Your new Speakman Product is designed for years of
trouble-free performance. Keep it looking new by
cleaning it periodically with a soft cloth. The use of harsh
chemicals and abrasives on any of the Speakman custom
finish products may damage the finish and void the
product warranty. Please be sure to only use approved
cleaners. Please contact Speakman for any clarification
of acceptable cleaners.
1
Remove the Handle Button Screw by inserting one of the included Mounting Screws thru the hole in the Handle.
2
Be sure to have properly adjusted the Temperature Limiting
Stop (TLS) as per the Valve Installation Instructions before
installing Valve Trim. Ensure the Valve is in the “OFF”
position. Install Trim Sleeve (1) onto the valve while aligning
the window of the Trim Sleeve (1) with the Bonnet Lug (2) of
the Valve.
3
Clean wall surface. Orient Wall Plate as shown below. Apply clear silicone sealant to the backside outer flat
surface of the wall plate, while leaving a small area open at the bottom. This will allow for any moisture to drain.
4
Align the Wall Plate (3) as shown below. Secure to Valve with the included Mounting Screws (4). Take care to not
over tighten Mounting Screws. Remove excess sealant after securing Wall Plate to wall.
5
Remove protective film from Valve Index Plate.
6
Align Valve Index Plate with Wall Plate and secure with the
included #6 screw and washer.
7
Align Handle vertically as shown below. Secure Handle to Spindle
with the included #8 Screw.
8
Insert Handle Button into the Handle
CPT-3000 REPAIR PARTS
SPEAKMAN
®
ITEM NO. PART NO. DESCRIPTION
RPG04-0381-PC HANDLE ASSEMBLY
RPG48-0035 MOUNTING HARDWARE
RPG41-0108 INDEX PLATE
RPG10-0082 WALL PLATE
RPG05-0832-PC SPINDLE SLEEVE
CPT-3000 ROUGH-IN DIAGRAM
SPEAKMAN
®
DIMENSIONS SUBJECT TO CHANGE WITHOUT NOTICE.
VALVE MOUNTING IS SHOWN FOR REFERENCE ONLY.
VALVE IS NOT INCLUDED WITH CPT-3000
7
1
2
"
191mm
3
7
16
"
88mm
6'-6" [2 METERS]
TO FLOOR
1'-9" [533mm]
4"-6" [1.4 METERS]
TO FLOOR
(SHOWER
INSTALLATION
ONLY)
4" [102mm]
TO TOP OF
TUB LEDGE
1"
25mm
HOLE FOR
SHOWER ARM
1"
25mm
HOLE FOR
TUB SPOUT
A
A
1/2" SWEAT
CONNECTION
1/2" SWEAT
CONNECTION
1/2" NPT FEMALE
1/2" SWEAT
CONNECTION
5-1/2" (140MM) DIA.
HOLE FOR
VALVE ACCESS
3
3
4
"
95mm
2
5
8
"
66mm
1
3
16
"
29mm
2-1/2" MIN
[64mm]
3-1/2" MAX
[89mm]
(ADJUSTMENT)
/
