PEC-4655
Owner's manual
PROGRAMMABLE CYCLE
ME MAGNETIC
HO
Testing specification :
EN 957-1+A1, EN 957-5.
Features of product with GS-TUV mark :
Mechanica safety.
Symbol of high quality.
Reliability assurance.
INDEX . . . . . . . .
. . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Introduction / Safety Guideline
Information PEC-4655
Service Information
Assembly
Exploded View
Parts List
01~02
03
03
04~05
06
07
A. INTRODUCTION
Thank you very much for choosing PROTEUS products. To secure the safety, pls read the
manual and all suggestions carefully before using the product. While you get everything ready,
believe that you could enjoy the pleasure of exercise and healthy.
B. SAFETY GUIDELINE
a. READ THE OWNER'S MANUAL AND ALL ACCOMPANYING LITERATURE AND
FOLLOW IT CAREFULLY BEFORE USING YOUR MACHINE.
b. THIS MACHINE IS INTENDED FOR INDOOR HOME USE ONLY. IT IS NOT DESIGNED
FOR COMMERCIAL USE.
c. INSPECT YOUR EXERCISE MACHINE PRIOR TO EXERCISING TO ENSURE THAT ALL
NUTS AND BOLTS ARE FULLY TIGHTENED BEFORE EACH USE.
d. MAKE SURE MACHINE IS STABILIZED ON THE FLOOR AND UNEVEN SURFACES ARE
LEVELED BEFORE USE.
e. MOST EXERCISE EQUIPMENT IS NOT RECOMMENDED FOR SMALL CHILDREN.
CHILDREN SHOULD NOT USE THE MACHINE UNLESS THEY ARE UNDER ADULT
SUPERVISION.
f. EXERCISE EQUIPMENT HAS MOVING PARTS. IN THE INTEREST OF SAFETY, KEEP
OTHERS, ESPECIALLY CHILDREN, AT A SAFE DISTANCE WHILE EXERCISING.
g. MAKE SURE ALL ADJUSTMENT DEVICES ARE FULLY INSERTED AND PROPERLY
ADJUSTED BEFORE USE TO AVOID INJURY.
h. REMOVE ALL JEWELRY, INCLUDING RINGS, CHAINS AND PINS BEFORE
COMMENCING EXERCISE.
i. ALWAYS WEAR SUITABLE CLOTHING AND FOOTWEAR DURING EXERCISE. DO NOT
WEAR LOOSE FITTING CLOTHING THAT COULD BECOME ENTANGLED WITH THE
MOVING PARTS OF YOUR EXERCISE MACHINE.
j. WARM UP 5 TO 10 MINUTES BEFORE EACH WORKOUT AND COOL DOWN 5 TO 10
MINUTES AFTERWARD. THIS ALLOWS YOUR HEART RATE TO GRADUALLY
INCREASE AND DECREASE AND WILL HELP PREVENT STRAINING MUSCLES.
k. NEVER HOLD YOUR BREATH WHILE EXERCISING. BREATHING SHOULD REMAIN AT
A NORMAL RATE IN CONJUNCTION WITH THE LEVEL OF EXERCISE BEING
PERFORMED.
l. REST ADEQUATELY BETWEEN WORKOUTS. MUSCLES TONE AND DEVELOP
DURING THESE REST PERIODS. BEGINNERS SHOULD WORK OUT TWICE A WEEK
AND INCREASE GRADUALLY TO 4 OR 5 TIMES PER WEEK.
m.DO NOT "OVER TRAIN". INCORRECT OR EXCESSIVE TRAINING MAY RESULT IN
INJURY.
- 1 -
- 2 -
IMPORTANT : THE MAXIMUM RECOMMENDED WEIGHT CAPACITY FOR YOUR
EQUIPMENT IS 125 KG ( 275 BL ). ALL OF THE TEST STIPULATE
TO THE EN 957-1+A1 / -5, CLASS HB.
NOTE : THE EQUIPMENT IS SPEED-DEPENDENT ON BRAKING SYSTEM.
WARNING : BEFORE COMMENCING WITH ANY EXERCISE PROGRAM, PLEASE CONSULT
YOUR PHYSICIAN. IF AT ANY TIME DURING EXERCISE YOU FEEL FAINT, DIZZY
OR EXPERIENCE PAIN, STOP AND CONSULT YOUR PHYSICIAN. IN THE EVENT
ANY OF THE ABOVE MENTIONED WARNINGS ARE BREACHED BY THE
CONSUMER. THE MANUFACTURER MAY USE SAME AS A DEFENSE TO ANY
CLAIM FOR INJURIES, DAMAGE OR LOSS. THE ABOVE WARNINGS ARE IN NO
WAY INTENDED TO LIMIT OR MODIFY THE CONSUMER'S REMEDIES FOR
BREACH OF WARRANTIES PURSUANT TO APPLICABLE FEDERAL AND STATE
LAWS OF REGULATIONS. THEY ARE BEING SUPPLIED STRICTLY TO ENSURE
THE SAFETY OF THE INDIVIDUALS USING THIS PRODUCT.
THE APPLIANCES ARE NOT FOR CHILDREN UNDER 14 YEARS OF AGES.
IMPORTANT : READ ALL INSTRUCTIONS CAREFULLY. ASSEMBLE THE UNIT IN
ACCORDANCE WITH THE STEPS IN THE MANUAL. LAY OUT ALL PARTS ON
THE FLOOR AND CHECK IF YOU HAVE ALL THE PARTS INCLUDED
COMPLETELY BEFORE BEGIN ASSEMBLY. IN CASE OF A DISCREPANCY,
PLEASE CALL CUSTOMER SERVICE OF THE STORE FOR HELP.
NOTE : SOME PARTS MAY BE FACTORY PRE-ASSEMBLED.
THE SAFETY LEVEL OF THE EQUIPMENT CAN BE MAINTAINED ONLY IF IT IS
EXAMINED REGULARLY FOR DAMAGED AND WEAR.
MINIMUM SAFE DISTANCE FRONT AND BACK NEED 50cm , LEFT AND
RIGHT SIDES NEED ABOUT 30cm.
THE " MAX INDICATOR LINE " WHICH MARKS ON THE SEAT TUBE
REPRESENT THAT THE MINIMUM INSERT DISTANCE , WHILE ADJUSTING THE
SEAT , PLEASE DO NOT CROSS THIS LINE.
THE PEDAL CRANK TRAINING EQUIPMENT OF CLASS B IS NOT SUITABLE
FOR THERAPEUTIC PURPOSES.
REPLACE DEFECTIVE COMPONENTS IMMEDIATELY AND KEEP THE
EQUIPMENT OUT OF USE UNTIL REPAIRED.
NOTE :DO NOT PLUG TO POWER SUPPLY BEFORE MACHINE IS
FULLY ASSEMBLED.
THE MACHINE IS REQUESTED TO USE DC TRANFORMER,
WHICH SHOULD BE WITH OUTPUT 6V/500 MA, PLEASE
ALSO REFER TO MONITOR INSTRUCTION FOR THE
PROPER SPECIFICATION INFORMATION.
BEFORE YOU BEGIN
THE MOST SUSCEPTIBLE TO WEAR PARTS ARE
DRUM MAGNETIC WHEEL / BELT
C. INFORMATION PEC-4655
E. SERVICE INFORMATION
PROTEUS SPORTS INC.
ADDRESS: 77-3, NANSHIN VILLAGE,
LINKOU, TAIPEI HSIEN, TAIWAN, R.O.C.
TEL : + 886-2-26093940 . 26090836
FAX : + 886-2-26093862 . 26002921
http : //www.proteusfitness.com
E-MAIL : [email protected]
- 3 -
Resistance Drum Magnetic Control
Driving Industrial Poly-V Belt 440-J6
Hub Industrial Double Sealed
Bearing 6004ZZ
Axle / Crank Three-Piece Type
User Weight 125 kg
Machine Size 102.0 x 70.0 x 130.0 cm
Carton Size 91.0 x 28.5 x 65.0 cm
NW / GW 36.9 / 40.3 kg
PEC-4655
WE ENCLOSE WITH THREE SIMPLE ASSEMBLING TOOLS FOR YOUR ASSEMBLY CONVENIENCE.
ONE SPANNER AND ONE ALLEN KEY AND ONE SCREWDRIVER
TOOLS REQUIRED FOR ASSEMBLY
D. CORRECT POSTURE FOR PEC-4655
STEP 1: ASSEMBLE STABILIZERS
a. ATTACH FRONT STABILIZER ( 02 )
TO THE MAIN FRAME ( 01 ) WITH
CARRIAGE BOLTS ( 27 ),
WASHERS ( 29 ) & DOME NUTS
( 33 ). THEN FULLY TIGHTEN THEM
WITH SPANNER.
b. ATTACH REAR STABILIZER ( 03 )
TO MAIN FRAME ( 01 ). FASTEN
WITH BOLTS ( 30 ), WASHERS ( 29 )
& DOME NUTS ( 33 ). THEN FULLY
TIGHTEN THEM WITH SPANNER.
NOTE : TO PREVENT DOME NUT ( 33 ) FROM
DAMAGING FLOOR, THE BOLT ( 27 )
& BOLT ( 30 ) MUST INSERT FROM
THE BOTTOM TO THE TOP.
STEP 2: ASSEMBLE PEDALS
a. ATTACH RIGHT PEDAL ( 18 ) TO
RIGHT CRANK ( 7R ), FULLY
TIGHTEN CLOCKWISE WITH
SPANNER.
b. ATTACH LEFT PEDAL ( 19 ) TO
LEFT CRANK ( 7L ), FULLY
TIGHTEN COUNTERCLOCKWISE
WITH SPANNER.
STEP 3: ASSEMBLE SADDLE & SEAT POST
a. ATTACH SADDLE ( 20 ) TO SADDLE
PLATE OF SLIDING TUBE ( 4b ).
FASTEN IT WITH WASHERS ( 31 )
AND NYLON NUTS ( 32 ). FULLY
TIGHTEN WITH SPANNER.
b. SLIDE THE SLIDING TUBE ( 4b )
INTO SEAT POST ( 4a ) AND
SECURE WITH KNOB ( 4c ), THEN
ATTACH SEAT POST ( 4a ) TO MAIN
FRAME ( 01 ).
c. ADJUST SADDLE ( 20 ) TO
DESIRED HEIGHT, TIGHTEN WITH
KNOB ( 26 ).
d. TO RELEASE THE KNOB ( 4c ) TO
ADJUST THE SADDLE ( 20 ) BACK
AND FORTH AT YOU DESIRED
POSITION. THEN FASTEN THE
KNOB ( 4c ).
- 4 -
ASSEMBLY
STEP 1
29
33
2
27
1
33
29
3
30
STEP 2
19
7R
18
STEP 3
20
4d
4c
4a
4b
26
32
31
1
IMPORTANT : READ STEP 2 BEFORE
ASSEMBLE PEDALS.
- 5 -
STEP 4: ASSEMBLE HANDLEBAR POST
CONNECT EXTENSION MONITOR
CABLE ( 09 ) AND LOWER MONITOR
CABLE ( 10 ), THEN FIT HANDLEBAR
POST ( 05 ) TO MAIN FRAME ( 01 )
WITH BOLTS ( 28 ) AND WASHERS
( 29 ), FULLY TIGHTEN THEM WITH
ALLEN KEY.
STEP 5: ASSEMBLE HANDLEBAR
INSERT PULSE WIRE ( 36 ) INTO
HANDLEBAR POST ( 05 ) AND LET IT
THROUGH THE TOP OF MONITOR
MOUNTING PLATE. ATTACH
HANDLEBAR ( 06 ) ONTO
HANDLEBAR POST ( 05 ), FIX WITH
WASHERS ( 29 ) AND BOLTS ( 28 ).
FULLY TIGHTEN THEM WITH ALLEN
KEY.
STEP 6: ASSEMBLE CYCLE MONITOR
a. CONNECT PULSE WIRE ( 36 ) &
EXTENSION MONITOR CABLE ( 09 )
TO MONITOR ( 08 ), THEN ATTACH
MONITOR ( 08 ) TO HANDLEBAR
POST ( 05 ), FASTEN WITH SCREW
( 22 ). THEN TIGHTEN THEM WITH
SCREWDRIVER.
b. TENSION ADJUSTMENT
OPERATING BY THE MOTOR.
PLEASE REFERS TO THE
OPERATING INSTRUCTION OF
MONITOR.
NOW YOUR PEC-4655 HAS BEEN FULLY
ASSAMBLED. THANK YOU FOR CHOOSING
PROTEUS PRODUCT !
STEP 4
28
29
5
9
10
1
STEP 5
5
6
36
29
28
STEP 6
5
9
22
36
8
17
23
6
29
33
30
25
4e
29
27
2
12
11
22
5
9
8
16
29
28
4a
24
13
1
7R
28
26
4b
10
29
9
32
31
33
18
3
19
4c
4d
15
4f
20
37
35
36
34
- 6 -
EXPLODED VIEW
GB
PEC4655-040126GB-GS
PARTS LIST
- 7 -
KEY DESCRIPTION Q'TY
1. MAIN FRAME 1
2. FRONT STABILIZER 1
3. REAR STABILIZER 1
4a. SEAT POST 1
4b. SLIDING TUBE 1
4c. KNOB W/ CLAMP (SMALL) 1
4d. 30 X 60 SLEEVE (75mm) 2
4e. 23 X 53 PLUG 1
4f. 25.4 ROUND PLUG 2
5. HANDLEBAR POST 1
6. HANDLEBAR 1
7R. CRANK (R) 1
7L. CRANK (L) 1
8. CYCLE MONITOR 1
9. EXTENSION MONITOR CABLE 1
10. LOWER MONITOR CABLE 1
11. CHAIN COVER (R-1) 1
12. CHAIN COVER (L-1) 1
13. CHAIN COVER (R-2) 1
14. CHAIN COVER (L-2) 1
15. 30 X 60 SLEEVE (210mm) 1
16. HANDLEBAR END CAP 2
17. FOAM GRIP 2
18. PEDAL (R) 1
19. PEDAL (L) 1
20. SADDLE 1
22. M5 SCREW X 10mm 4
23. WHEEL 2
24. FOOT CAP 2
25. FOOT ADJUSTER BASE 2
26. KNOB W/ CLAMP 1
27. M8 CARRIAGE BOLT X 90mm 2
28. M8 SOCKET BOLT X 15mm 6
29. M8 WASHER 8
30. M8 CARRIAGE BOLT X 55mm 2
31. M8 WASHER 3
32. M8 NYLON NUT 3
33. M8 DOME NUT 2
34. POWER TRANSFORMER 1
35. M4 SCREW 2
36. PULSE WIRE 1
37. GRIP PULSE 2
38. POWER TRANSFORMER 1
/
