Snapper 331723BVE (7084954) User manual

Brand: Snapper

Model: 331723BVE (7084954)

Category: Lawnmowers

Type: User manual

Safety Instructions & Operator’s Manual for

REAR ENGINE RIDING MOWER

SERIES 23

MODELS

281123BV

2811523BV

281223BVE

2812523BVE

2813523BVE

301123BV

3011523BV

301223BVE

3012523BVE

3013523BVE

331323HVE

331523KVE

331623BVE

331723BVE

MODEL NUMBER EXPLANATION

33 15 23 K V E

CUTTING WIDTH ENGINE OPTIONS

ENGINE HP * ENGINE TYPE

SERIES DESIGNATION ENGINE MODEL

28 - 28” Cutting Deck

- 30” Cutting Deck

- 33” Cutting Deck

11 – 11.0 HP Engine

115 – 11.5 HP Engine

12 – 12.0 HP Engine

125 – 12.5 HP Engine

13 – 13.0 HP Engine

135

- 13.5 HP Engine

15 – 15.0 HP Engine

16 – 16.0 HP Engine

17 – 17.0 HP Engine

- Series Designation B - Briggs Engine

K - Kohler Engine

H - Honda Engine

- Over Head Valve

- Electric Start

Thank you for buying a SNAPPER Product! Before operating your machine, read this manual carefully and pay

particular attention to the “IMPORTANT SAFETY INSTRUCTIONS” on Pages 2 thru 4. Remember that all power

equipment can be dangerous if used improperly. Also keep in mind that SAFETY requires careful use in

accordance with the operating instructions and common sense!

NOTE: Specifications are correct at time of printing and are subject to change without notice.

* Actual sustained equipment horsepower will likely be lower due to operating limitations and environmental factors.

SNAPPER – A DIVISION OF SIMPLICITY MFG., INC.

MANUAL No. 7100310 (I.R. 7/14/2005)

IMPORTANT SAFETY INSTRUCTIONS

WARNING: This powerful cutting machine is capable of amputating hands and feet and can throw objects that

can cause injury and damage! Failure to comply with the following SAFETY instructions could result in serious

injury or death to the operator or other persons. The owner of the machine must understand these instructions

and must allow only persons who understand these instructions to operate machine. Each person operating

the machine must be of sound mind and body and must not be under the influence of any substance, which

might impair vision, dexterity or judgment. If you have any questions pertaining to your machine which your

dealer cannot answer to your satisfaction, call or write the Customer Service Department at SNAPPER,

McDonough, Georgia 30253. Phone: (1-800-935-2967).

PROTECTION FOR CHILDREN

Tragic accidents can occur if the operator is not alert to the

presence of children. Children are often attracted to the

machine and the mowing activity. Children who have been

given rides in the past may suddenly appear in the mowing

area for another ride and be run over or backed over by the

machine. Never assume that children will remain where you

last saw them.

1. KEEP children out of the mowing area and under the

watchful care of a responsible adult other than the

operator.

2. DO NOT allow children in yard when machine is

operated (even with the blade OFF).

3. DO NOT allow children or others to ride on machine,

attachments or towed equipment (even with the blades

OFF). They may fall and be seriously injured.

4. DO NOT allow pre-teenage children to operate

machine.

5. ALLOW only responsible adults & teenagers with

mature judgment under close adult supervision to

operate machine.

6. DO NOT operate blades in reverse. STOP BLADES.

LOOK and SEE behind and down for children, pets and

hazards before and while backing.

7. USE EXTRA CARE when approaching blind corners,

shrubs, trees, or other objects that may obscure vision.

PROTECTION AGAINST TIPOVERS

Slopes are a major factor related to loss-of-control and tip-

over accidents, which can result in severe injury or death.

All slopes require extra CAUTION. If you cannot back up

the slope or if you feel uneasy on the slope, DO NOT mow

it. Use extra care with grass catchers or other attachments;

these affect the handling and the stability of the machine.

1. DO NOT operate machine on slopes exceeding 15

degrees (27% grade).

2. Exercise EXTREME CAUTION on slopes above 10

degrees (18% grade). Turn blades OFF when traveling

uphill. Use a slow speed and avoid sudden or sharp

turns.

3. DO NOT operate machine back and forth across face

of slopes. Operate up and down. Practice on slopes

with blades off.

4. AVOID starting, stopping or turning on slopes. If

machine stops going uphill or tires lose traction, turn

blades OFF and back slowly straight down the slope.

PROTECTION AGAINST TIPOVERS

(Continued From Previous Column)

5. STAY ALERT for holes and other hidden hazards. Tall

grass can hide obstacles. Keep away from ditches,

washouts, culverts, fences and protruding objects.

6. KEEP A SAFE DISTANCE (at least 3 feet) away from

edge of ditches and other drop offs. The machine

could turn over if an edge caves in.

7. Always begin forward motion slowly and with caution.

8. Use weights or a weighted load carrier in accordance

with instructions supplied with a grass catcher. DO

NOT operate machine on slopes exceeding 10 degrees

(18% grade) when equipped with grass catcher.

9. DO NOT put your foot on the ground to try to stabilize

the machine.

10. DO NOT operate machine on wet grass. Reduced

traction could cause sliding.

11. Chose a low enough speed setting so that you will not

have to stop or shift on a slope. Tires may lose traction

on slopes even though the brakes are functioning

properly.

12. DO NOT operate machine under any condition where

traction, steering or stability is doubtful.

13. Always keep the machine in gear when going down

slopes. DO NOT shift to neutral (or actuate hydro roll

release) and coast downhill.

PREPARATION

1. Read, understand, and follow instructions and

warnings in this manual and on the machine, engine

and attachments. Know the controls and the proper

use of the machine before starting.

2. Only mature, responsible persons shall operate the

machine and only after proper instruction.

3. Data indicates that operators age 60 and above, are

involved in a large percentage of mower-related

injuries. These operators should evaluate their ability

to operate the mower safely enough to protect

themselves and others from serious injury.

4. Handle fuel with extra care. Fuels are flammable and

vapors are explosive. Use only an approved fuel

container. DO NOT remove fuel cap or add fuel with

engine running. Add fuel outdoors only with engine

stopped and cool. Clean spilled fuel from machine. DO

NOT smoke.

5. Practice operation of machine with BLADES OFF to

learn controls and develop skills.

IMPORTANT SAFETY INSTRUCTIONS

PREPARATION

(Continued From Previous Page)

6. Check the area to be mowed and remove all objects

such as toys, wire, rocks, limbs and other objects

that could cause injury if thrown by blade or

interfere with mowing.

7. Keep people and pets out of mowing area.

Immediately STOP blades, STOP engine, and

STOP machine if anyone enters the area.

8. Check shields, deflectors, switches, blade

controls and other safety devices frequently for

proper operation and location.

9. Make sure all safety decals are clearly legible.

Replace if damaged.

10. Protect yourself when mowing and wear safety

glasses, long pants and substantial footwear.

11. Know how to STOP blades and engine quickly

in preparation for emergencies.

12. Use extra care when loading or unloading the

machine into a trailer or truck.

13. Check grass catcher components frequently for

signs of wear or deterioration and replace as

needed to prevent injury from thrown objects

going through weak or worn spots.

SAFE HANDLING OF GASOLINE

To avoid personal injury or property damage, use

extreme care in handling gasoline. Gasoline is

extremely flammable and the vapors are explosive

1. Extinguish all cigarettes, cigars, pipes and

other sources of ignition.

2. Use only an approved fuel container.

3. DO NOT remove fuel cap or add fuel with the

engine running. Allow the engine to cool before

refueling.

4. DO NOT refuel the machine indoors.

5. DO NOT store the machine or fuel container

inside where there is an open flame, spark or

pilot light such as on a water heater or other

appliances.

6. DO NOT fill fuel containers inside a vehicle or

on a truck or trailer bed with a plastic liner.

Always place the containers on the ground

away from the vehicle before filling.

7. Remove gas-powered equipment from the

vehicle or trailer and refuel it on the ground. If

this is not possible, then refuel equipment

using a portable container, rather than a

gasoline dispenser nozzle.

8. DO NOT start gas powered equipment in

enclosed vehicles or trailers.

9. Keep the nozzle in contact with the rim of the

fuel tank or container opening at all times until

fueling is complete. DO NOT use a nozzle lock-

open device

10. If fuel is spilled on clothing, change clothing

immediately.

11. Never overfill a fuel tank. Replace fuel cap and

tighten securely.

OPERATION

1. Mount and dismount machine from left side.

Keep clear of discharge opening at all times.

2. Start engine from operator's seat, if possible.

Make sure blades are OFF and parking brake is

set.

3. DO NOT leave machine with engine running.

STOP engine, STOP blades, SET brake, and

Remove key before leaving operators position

of any reason.

4. DO NOT operate machine unless properly

seated with feet on feet rests or pedal(s).

5. STOP BLADES and ENGINE and make sure

blades have stopped before removing grass

catcher or unclogging mower to prevent loss of

fingers or hand.

6. Blades must be OFF except when cutting grass.

Set blades in highest position when mowing

over rough ground.

7. Keep hands and feet away from rotating blades

underneath deck. DO NOT place foot on ground

while BLADES are ON or machine is in motion.

8. DO NOT operate machine without entire grass

catcher or guards in place and working. DO

NOT point discharge at people, passing cars,

windows or doors.

9. Slow down before turning.

10. Watch out for traffic when near or crossing

roadways.

11. STOP engine immediately after striking an

obstruction. Inspect machine and repair

damage before resuming operation.

12. Operate machine only in daylight or with good

artificial light.

13. Move joystick (if equipped) SLOWLY to

maintain control during speed and directional

changes.

14. Exercise CAUTION when pulling loads. Limit

loads to those you can safely control and attach

loads to hitch plate as specified with SNAPPER

attachment instructions.

15. On slopes, the weight of the towed equipment

may cause loss of traction and loss of control.

When towing, travel slowly and allow extra

distance to stop.

16. DO NOT operate engine in enclosed areas.

Engine exhaust gases contain carbon

monoxide, a deadly poison.

17. DO NOT discharge material against a wall or

obstruction. Material may ricochet back

towards the operator.

18. Only use accessories approved by the

manufacturer. See manufacturer’s instructions

for proper operation and installation of

accessories.

IMPORTANT SAFETY INSTRUCTIONS

TOWING

1. Tow only with a machine that has a hitch

designed for towing. DO NOT attach towed

equipment except at the hitch point.

2. Follow the manufacturer’s recommendation for

weight limits for towed equipment and towing

on slopes.

3. DO NOT allow children or others on towed

equipment.

4. On slopes, the weight of the towed equipment

may cause loss of traction and loss of control.

5. Travel slowly and allow extra distance to stop.

MAINTENANCE

1. DO NOT store machine or fuel container inside

where fumes may reach an open flame, spark or

pilot light such as in a water heater, furnace,

clothes dryer or other gas appliance. Allow

engine to cool before storing machine in an

enclosure. Store fuel container out of the reach

of children in a well ventilated, unoccupied

building.

2. Keep engine free of grass, leaves or excess

grease to reduce fire hazard and engine

overheating.

3. When draining fuel tank, drain fuel into an

approved container outdoors and away from

open flame.

4. Check brakes frequently; adjust, repair or

replace as needed.

5. Keep all bolts, nuts and screws properly tight.

Check that all cotter pins are in proper position.

6. Always provide adequate ventilation when

running engine. Exhaust gases contain carbon

monoxide, an odorless and deadly poison.

7. Disconnect negative (black) cable from battery

before performing maintenance or service.

Cranking engine could cause injury.

8. DO NOT work under machine without safety

blocks.

9. Service engine and make adjustments only

when engine is stopped. Remove spark plug

wire(s) from spark plug(s) and secure wire(s)

away from spark plug(s).

10. DO NOT change engine governor speed

settings or overspeed engine.

11. Lubricate machine at intervals specified in

manual to prevent controls from binding.

12. Mower blades are sharp and can cut. Wrap the

blades or wear heavy leather gloves and use

CAUTION when handling them.

13. DO NOT test for spark by grounding spark plug

next to spark plug hole; spark plug could ignite

gas exiting engine.

14. Have machine serviced by an authorized

SNAPPER dealer at least once a year and have

the dealer install any new safety devices.

15. Maintain or replace safety and instruction labels

as necessary.

MAINTENANCE

(Continued From Previous Column)

16. Use only genuine SNAPPER replacement parts

to assure that original standards are

maintained.

TABLE OF CONTENTS

IMPORTANT SAFETY INSTRUCTIONS ........................................................................2-4

TABLE OF CONTENTS ..................................................................................................... 5

SECTION 1 - FAMILIARIZATION ...................................................................................... 6

SECTION 2 - OPERATING INSTRUCTIONS ...............................................................7-13

Pre-start Checklist ......................................................................................................... 7

Operator’s Seat Adjustment ......................................................................................... 7

Starting & Stopping Engine, Blade & Wheel Drive................................................8-11

Starting & Stopping Mower Blades.......................................................................10-11

Starting & Stopping Wheel Drive ..........................................................................10-11

Parking Brake............................................................................................................... 12

Cutting Height Adjustment ......................................................................................... 12

Reverse Lockout Mechanism ..................................................................................... 13

SECTION 3 - MAINTENANCE INSTRUCTIONS........................................................14-19

Service – After First 5 Hours .................................................................................14-16

Change Engine Oil.................................................................................................... 14

Service Engine Air Cleaner...................................................................................... 14

Check Mower Blade ................................................................................................. 14

Check Blade Drive Belt ............................................................................................ 15

Blade Brake............................................................................................................... 15

Service Brake / Park Brake...................................................................................... 15

Check Interlock System........................................................................................... 16

Reverse Lockout Mechanism.................................................................................. 16

Lubrication – Grease Fittings – Overview ............................................................. 16

Service – Every 25 Operating Hours.....................................................................16-18

Check Engine............................................................................................................ 16

Battery Fluid Level ................................................................................................... 17

Mower Deck Levelness ............................................................................................ 17

Clean Mower Deck.................................................................................................... 17

Mower Blade Spindle – Lubrication ....................................................................... 17

Mower Deck Linkage – Lubrication ........................................................................ 17

Front Wheel Bearing – Lubrication......................................................................... 17

Shift Lever – Lubrication ......................................................................................... 17

Rear Axle Bearing – Lubrication............................................................................. 18

Differential / Chain Case – Lubrication .................................................................. 18

Service – Annually....................................................................................................... 18

Engine........................................................................................................................ 19

Fuel Filter................................................................................................................... 19

Every Two Years .......................................................................................................... 19

Storage – Out of Season ............................................................................................. 19

Removing Fuel Tank.................................................................................................... 19

SECTION 4- ADJUSTMENTS AND REPAIR .............................................................20-28

Engine Adjustments & Repair .................................................................................... 20

Mower Deck & Component Adjustments .................................................................. 20

Blade Brake Adjustment ............................................................................................. 20

Mower Deck Adjustment (Side to Side Levelness) .................................................. 21

Mower Deck Adjustment (Front to Rear Levelness) ................................................ 21

Mower Drive Belt Adjustment – 28” & 30” Decks..................................................... 22

Rear Engine Rider Drive Components ...................................................................... 23

Service Brake/Park Brake Adjustment ...................................................................... 23

Mower Blade Replacement ......................................................................................... 24

Blade Sharpening ........................................................................................................ 24

Mower Drive Belt Removal/Replacement – 28” 30” & 33” Decks ........................... 25

Battery Removal, Replacement, Service ..............................................................26-28

ACCESSORIES............................................................................................................. 28

TROUBLESHOOTING ................................................................................................29-30

MAINTENANCE SCHEDULE........................................................................................... 31

MAINTENANCE/REPLACEMENT PARTS...................................................................... 32

WARRANTY ..................................................................................................................... 33

PRIMARY MAINTENANCE.........................................................................................34-37

PRODUCT REGISTRATION FORM ................................................................................ 38

Section 1 - FAMILIARIZATION

FIGURE 1.1

1.1 INTRODUCTION

This manual has been prepared for the operator’s of the

SNAPPER Rear Engine Rider. Its purpose, aside from

recommending standard operating procedures and

routine service requirements, is to promote SAFETY

through the use of accepted operating practices. Read,

Understand and Follow the IMPORTANT SAFETY

INSTRUCTIONS on Pages 2 thru 4 of this manual and

All SAFETY messages on the Rear Engine Rider and its

attachments before operating.

1.2 NOMENCLATURE

The nomenclature drawing above, Figure 1.1, shows the

essential parts of the SNAPPER Rear Engine Rider. It is

recommended that all operators of this equipment

become thoroughly familiar with the controls,

components, and operation of this machine before

operating. Specific details involving the engine are

found in the separate engine owner’s manual. Study

these manuals before operating and keep both handy

for future reference.

FUEL TANK

TRANSMISSION

SHIFT LEVER

STEERING

WHEEL

IGNITION

SWITCH

CLUTCH/BRAKE

PEDAL

PARK BRAKE

LATCH

BLADE LEVER

DISCHARGE

DEFLECTOR

OVERRIDE

CONTROL

ENGINE SPEED

CONTROL

BLADE PEDALS

IMPORTANT: The figures and illustrations in this manual are provided for reference only and may differ from your

specific model. Contact your Snapper dealer if you have questions.

Section 2 - OPERATING INSTRUCTIONS

2.1 PRE-START CHECK LIST

Make the following checks and perform the service

required before each start-up.

2.1.1. Check tires and add or release air as needed

to bring pressure to 12 PSI in front and 12 PSI in rear

tires.

2.1.2. Check guards, deflectors and covers to make

sure all are in place and securely tightened.

2.1.3. Check engine oil and add oil as needed to

bring level up to the FULL mark. Refer to engine

owner’s manual for oil specifications. See Figure 2.1.

FIGURE 2.1

2.1.4. Adjust seat as needed to most comfortable

position. Refer to Section “OPERATOR’S SEAT

ADJUSTMENT”.

2.1.5. Check blade control to insure it works freely.

If blade pedals are depressed, blade lever can be

moved manually from “ON” to “OFF” to stop

blade.

2.1.6. Check Reverse Lockout Mechanism. With

blade pedals depressed, shift lever must not go into

reverse.

2.1.7. Clean exterior surfaces of cutting deck and

engine of any accumulation of dirt, grass, oil, etc.

Keep engine air intake screen and cooling fins clear

at all times.

2.1.8. Add fuel to tank after pushing the Rear Engine

Rider outside where fumes can dissipate. Make sure

fuel filler cap is tight and vent is open after refueling.

Refer to engine owner’s manual for fuel

specifications. See Figure 2.2.

FIGURE 2.2

2.2 OPERATOR’S SEAT ADJUSTMENT

2.2.1. FRONT TO REAR ADJUSTMENT

1. With the engine stopped, loosen the two adjusting

knobs and move seat to desired position. After

adjustment, tighten knobs securely. If seat does not

move after loosening knobs, it may be necessary to

loosen the 5/16” patch lock screws or hex nuts

located at the rear of the seat. See Figure 2.3.

FIGURE 2.3

SAFE LEVEL

AREA

OPEN

VENT

FUEL

FILLER

CAP

FUEL

TANK

ADJUSTING

KNOBS

OPERATOR’S

SEAT

5/16” PATCH LOCK

SCREWS (DO NOT

OVERTIGHTEN

)

ADJUSTING

KNOBS

OPERATOR’S

SEAT

HEX NUTS

(DO NOT

OVERTIGHTEN)

Section 2 - OPERATING INSTRUCTIONS

2.3 STARTING & OPERATION

2.3.1. ENGINE (ELECTRIC START)

IMPORTANT: When the ignition key is turned to

“START”, the engine will turn over, but will

not start

unless the Clutch/Brake pedal is pressed all the way

down, the Blade Lever is in the “OFF” position (See

Figure 2.5). The operator should be in the seat. Start

engine as follows:

1. Move transmission shift lever to (N) Neutral

position. DO NOT start engine with transmission

shift lever in a drive position.

WARNING

It is possible to start engine with transmission shift

lever in a drive position. Follow starting instructions

carefully.

2. Make certain the Blade Lever is in the “OFF”

position. See Figure 2.4.

FIGURE 2.4

3. Press Clutch/Brake Pedal all

the way down and

hold while starting engine. See Figure 2.5.

4. Open vent on fuel filler cap by turning

counterclockwise. IMPORTANT: Failure to open

vent on the fuel filler cap can cause engine to stall.

See Figure 2.2.

5. Move engine speed control to the choke position

to start a cold engine. See Figure 2.6.

6. Turn key to the “START” position until engine

starts. See Figure 2.7. NOTE: If after 5 seconds of

cranking the engine and it does not start, release the

key, make sure the Clutch/Brake Pedal is fully

depressed and attempt starting again after waiting for

approximately 20 seconds.

7. After engine starts, move engine speed control to

the “FAST” position, allow a brief warm-up until

engine runs smooth.

FIGURE 2.5

FIGURE 2.6

FIGURE 2.7

(Continued on Next Page)

BLADE LEVER IN

“OFF” POSITION

RELEASE BLADE

PEDALS

TO START ENGINE,

PUSH CLUTCH/BRAKE

PEDAL ALL THE WAY

DOWN

PARKING

BRAKE

LATCH

CHOKE

POSITION

ENGINE

SPEED

CONTROL

KEY

Section 2 - OPERATING INSTRUCTIONS

2.3 STARTING & OPERATION

2.3.1. ENGINE (ELECTRIC START) (Continued)

8. Should the battery be too weak to start the engine,

refer to Section “ENGINE (MANUAL START)” to

manually start the electric start engines.

9. On Model 3314522BVE, the engine is equipped

with a fuel shut-off solenoid. If the battery is dead, the

engine can be started with the recoil back-up starter if

the throttle control is in the choke position (HOT

engine or COLD engine).

2.3.2. ENGINE (MANUAL START)

IMPORTANT: When the ignition key is turned to

“ON”, and the recoil handle is pulled, the engine will

turn over, but will

not start unless the Clutch/Brake

Pedal is pressed all the way down with Parking

Brake engaged (See Figure 2.8) and the Blade

Lever is in the “Off” position (See Figure 2.4). Start

engine as follows:

1. Move transmission shift lever to (N) Neutral

position. DO NOT start engine with transmission shift

lever in a drive position.

WARNING

It is possible to start engine with transmission shift

lever in a drive position. Follow starting instructions

carefully.

2. Make certain the Blade Lever is in the “OFF”

position. See Figure 2.4.

3. Press Clutch/Brake Pedal all

the way down,

move Parking Brake Latch over and release the

Clutch/Brake Pedal to set Parking Brake. See

Figure 2.8.

FIGURE 2.8

4. Open vent on fuel filler cap by turning

counterclockwise. NOTE: Failure to open vent on

the fuel filler cap can cause engine to stall.

5. Move engine speed control to the choke position

to start a cold engine. See Figure 2.6.

6. Turn key to “ON” position. See Figure 2.9.

FIGURE 2.9

7. Pull starter rope with a smooth, even motion

until engine starts. Always guide the starter rope

back into the recoil housing. Never allow rope to

snap back. After Engine starts, move engine speed

control to the “FAST” position.

8. Allow a brief warm-up until engine runs smooth.

TO START ENGINE,

PUSH CLUTCH/BRAKE

PEDAL ALL THE DOWN

MOVE

PARKING

BRAKE

LATCH

OVER

KEY

Section 2 - OPERATING INSTRUCTIONS

WARNING

Once blade is disengaged, it should come to a

complete stop in 3 seconds or less. If the blade

continues to rotate after 3 seconds, the blade brake

must be adjusted. Refer to Section “BLADE BRAKE

ADJUSTMENT” for adjustment procedures or return

machine to an authorized SNAPPER dealer for

adjustment. DO NOT CONTINUE to operate machine

until blade brake is adjusted and functioning

properly.

2.3 STARTING & OPERATION

2.3.3. MOWER BLADE

1. With engine running, move engine speed control

to the “FAST” position.

2. Move blade lever forward to the “ON” position,

then depress blade pedals to hold blade lever in the

“ON” position. See Figure 2.10.

FIGURE 2.10

2.3.4. WHEEL DRIVE

1. With engine running, adjust engine speed

control to “FAST” position.

2. Depress clutch/brake pedal. See Figure 2.11.

3. Place transmission shift lever in notch for first

speed. See Figure 2.12.

4. Release clutch/brake pedal to begin desired

ground speed.

5. During forward motion, the transmission shift

lever may be placed in any desired forward speed

without depressing the clutch/brake pedal.

NOTE

: For best cutting results, move the transmission

shift lever into a slow forward speed and the engine

speed control to a fast position. This combination will

allow the mower blades to lift the grass while cutting

smoothly and evenly.

WARNING

DO NOT operate blades in reverse. STOP BLADES.

LOOK and SEE behind and down for children, pets

and hazards before and while backing.

FIGURE 2.11

FIGURE 2.12

BLADE LEVER SHOWN IN

“ON” POSITION

BLADE PEDAL

SHOWN

DEPRESSED

THERE ARE FIVE

DIFFERENT FORWARD

GROUND SPEEDS AND ONE

REVERSE GROUND SPEED

SHIFT LEVER SHOWN IN

NEUTRAL POSITION

DEPRESS

CLUTCH/BRAKE

PEDAL

Section 2 - OPERATING INSTRUCTIONS

WARNING

DO NOT leave the machine with the engine running.

STOP Blade. STOP engine. Shift to neutral and

engage park brake. Remove key.

2.4 STOPPING - ENGINE, WHEEL DRIVE, BLADE

2.4.1. ENGINE

1. Stop engine by turning key to the “OFF” position.

See Figure 2.13.

FIGURE 2.13

2.4.2. WHEEL DRIVE

1. Stop motion of Rear Engine Rider by pushing

clutch/brake pedal all the way “DOWN” to apply

brake. See Figure 2.14.

WARNING

Once blade is disengaged, it should come to a

complete stop in 3 seconds or less. If the blade

continues to rotate after 3 seconds, the blade brake

must be adjusted. Refer to Section “BLADE BRAKE

ADJUSTMENT” for adjustment procedures or return

machine to an authorized SNAPPER dealer for

adjustment. DO NOT CONTINUE to operate machine

until blade brake is adjusted and functioning

properly.

2.4.3. MOWER BLADE

1. Stop mower blade by releasing blade pedals or

moving blade lever rearward to the “OFF” position.

See Figure 2.15.

FIGURE 2.14

FIGURE 2.15

BLADE LEVER IN “OFF”

POSITION

RELEASE BLADE

PEDALS

TURN TO

“OFF”

POSITION

KEY

TO APPLY

BRAKES, PUSH

CLUTCH/BRAKE

PEDAL ALL THE

WAY DOWN

CLUTCH/BRAKE

PEDAL

PARK BRAKE

LATCH SHOWN

ENGAGED

Section 2 - OPERATING INSTRUCTIONS

2.4 STOPPING - ENGINE, WHEEL DRIVE, BLADE

2.4.4. PARK BRAKE

1. Engage park brake by pushing clutch/brake pedal

“DOWN” and moving the park brake latch to the

“ENGAGED” position. While holding the park brake

latch “ENGAGED”, release clutch/brake pedal to set

park brake. See Figure 2.16.

WARNING

DO NOT park the machine on slopes.

FIGURE 2.16

2. Release park brake by pushing down on the

clutch/brake pedal, parking brake latch will move to

the “OFF” position unassisted. See Figure 2.17.

FIGURE 2.17

2.5. CUTTING HEIGHT ADJUSTMENT

1. Adjust cutting height as desired to any one of

five positions using deck lift lever. Move deck lift

lever up or down to desired cutting height and then

move over to secure in the height of cut notch.

See Figure 2.18.

FIGURE 2.18

CLUTCH/BRAKE

PEDAL

PARK BRAKE

LATCH SHOWN

ENGAGED

CLUTCH/BRAKE

PEDAL SHOWN

DISENGAGED

PARK BRAKE

LATCH SHOWN

IN “OFF”

POSITION

HEIGHT OF CUT

NOTCHES

DECK LIFT

LEVER

Section 2 - OPERATING INSTRUCTIONS

2.6 REVERSE LOCKOUT MECHANISM

Data indicates that tragic back-over accidents occur

each year. These accidents usually involve

unsupervised children. Many times these children have

been given rides on the machine and have been trained

to view this potentially dangerous piece of machinery

as fun rather than being taught how to avoid danger.

This riding mower has a Reverse Lockout Mechanism.

This mechanism prevents the mower from being shifted

into reverse with the blade running. To shift into reverse

you must first stop the blade by releasing the blade

pedals and then shift to reverse. It is our

recommendation that this mechanism remain functional

and the operator of this equipment develop the habit of

never backing up with the blade running. As the Safety

Instructions Indicate, DO NOT operate blades in

reverse. STOP BLADES, LOOK AND SEE BEHIND

AND DOWN for children, pets and hazards before

and while backing.

We realize that this could cause a change to your

previous mowing method but we encourage you to

adjust to this new system. Do not defeat the Reverse

Lockout Mechanism.

If you operate your mower near roadways or use

attachments that require quicker shifting to reverse,

there is an override lever provided. This lever can be

pushed and held before starting the blade and will allow

reverse operation until the blade pedals are released,

at which time the system will return to its Reverse

Lockout mode. This feature should never be selected

unless you are absolutely sure that no children or

others are present in the mowing area and that all

children are away and supervised by a responsible

adult.

2.6.1. Reverse Lockout Mechanism Override

1. Stop machine. Stop blade.

2. Depress and hold Override Lever.

3. Depress and hold Blade Pedals. Release

Override Lever.

4. Move blade lever forward to “ON” position.

WARNING

LOOK and SEE behind and down for children, pets

and hazards before and while backing.

IMPORTANT: DO NOT use the Reverse Lockout

Mechanism Override as the normal operating mode. To

return to the Reverse Lockout Mechanism mode,

release blade pedals to turn blade off. The Override will

reset to Reverse Lockout. Check the Reverse Lockout

Mechanism frequently for proper function. With the

blade pedals depressed, the shift lever must not go into

reverse. DO NOT operate machine if Reverse Lockout

Mechanism is not functioning properly. Contact your

local Snapper dealer for assistance.

DANGER

LOOK and SEE behind and down for children, pets

and hazards before and while backing.

BLADES must be turned off before backing

machine.

DO NOT allow children on machine (even with

blades off) or in yard when mowing.

Section 3 – MAINTENANCE

WARNING

DO NOT attempt any adjustments, maintenance,

service or repairs with the engine running. STOP

engine. STOP blade. Engage parking brake. Remove

key. Remove spark plug wire from spark plug and

secure away from plug. Engine and components are

HOT. Avoid serious burns, allow all parts to cool before

working on machine. Fuel Filler Cap and vent must be

closed securely to prevent fuel spillage.

3.1 INTRODUCTION

To retain the quality of the Rear Engine Rider, use

genuine SNAPPER replacement parts only. Contact

a local SNAPPER dealer for parts and service

assistance. For the correct part or information for a

particular Rear Engine Riding Mower, always mention

the model and serial number. SNAPPER

recommends returning the Rear Engine Rider to an

authorized SNAPPER dealer annually for inspection

and addition of any new devices, which might upgrade

the safety of the Rear Engine Rider. For the nearest

SNAPPER dealer in your area, check the yellow

pages under the heading LAWN MOWERS. For

engine parts and service, look for the engine

manufacturer’s dealers under the heading, ENGINES

- gasoline.

3.2 SERVICE - AFTER FIRST 5 HOURS

Routine maintenance is important to the performance

and life of your Rear Engine Rider. Service performed

properly and at the recommended interval is essential.

Refer to Section “MAINTENANCE SCHEDULE” in this

manual and in the Engine Owner’s Manual. Carefully

complete all of the recommended service procedures.

3.2.1. CHANGE ENGINE OIL

1. Place bricks or wooden blocks under the front

wheels to lower rear of engine.

2. Loosen or remove oil fill cap on engine.

3. Loosen oil drain plug.

4. Place a 2 quart minimum capacity container

under the end of the oil drain. Open oil drain. See

Figure 3.1 for oil drains used on the Rear Engine

Riders.

FIGURE 3.1

5. After all the oil has drained, close the drain and

wipe up any oil that may have spilled. See Figure

3.1. Dispose of used oil properly.

6. Fill engine crankcase with new oil. Refer to

your engine owner’s manual for oil specifications.

7. Change oil filter on engines equipped with oil

filters at every oil change. Refer to your engine

owner’s manual for service instructions.

3.2.2. SERVICE ENGINE AIR CLEANER

The engine is equipped with a dual element air

cleaner. Both the foam pre-cleaner and cartridge

require service. Refer to Engine Owner’s Manual

for recommended service procedures.

3.2.3. CHECK MOWER BLADE

1. Follow WARNING statement found on this page.

2. Check fuel level in tank. If over 3/4 full, remove

tank. Refer to Section “REMOVING FUEL TANK”.

If 3/4 or less, proceed to next step.

3. Carefully stand Rear Engine Rider on rear

bumper.

WARNING

Remove the battery if the Rear Engine Rider will be left

standing on the rear bumper for longer than 2 hours.

Refer to Section “BATTERY REMOVAL”. DO NOT use

a cutting blade that shows signs of excessive wear or

damage on the Rear Engine Rider. Refer to Section

“MOWER BLADE REPLACEMENT” for proper blade

inspection and service procedures.

4. Check torque of blade mounting bolts. As

necessary, torque to 30 to 40 ft. lbs. See Figure 3.2.

5. Check blade for sharpness, wear and damage.

Refer to Section “BLADE WEAR LIMITS”.

FIGURE 3.2

6. Check blade for straightness. Refer to Section

“ADJUSTING MOWER BLADE”.

REMOVE OIL PLUG TO

ALLOW OIL TO DRAIN

ROTATE COUNTER-

CLOCKWISE AND

PULL OUT TO OPEN

PUSH IN AND ROTATE

CLOCKWISE TO CLOSE

TORQUE BLADE

MOUNTING BOLTS TO

30 TO 40 FT. LBS.

Section 3 - MAINTENANCE

WARNING

DO NOT attempt any adjustments, maintenance,

service or repairs with the engine running. STOP

engine. STOP blade. Engage parking brake. Remove

key. Remove spark plug wire from spark plug and

secure away from plug. Engine and components are

HOT. Avoid serious burns, allow all parts to cool

before working on machine. Fuel Filler Cap and vent

must be closed securely to prevent fuel spillage.

3.2 SERVICE - AFTER FIRST 5 HOURS

3.2.4. CHECK BLADE DRIVE BELT

The blade drive consists of a single belt from the

engine to the deck. Inspect for signs of

deterioration and proper tension.

1. Lower deck to lowest setting.

2. Remove four self-tapping screws, two on each

side of mower drive belt cover. See Figure 3.3.

3. Slide cover back and rotate out on left side of

mower deck.

FIGURE 3.3

4. With engine “OFF” and deck in 3rd height of cut

position, move blade lever back to the “ON”

position and depress blade pedals.

5. 28” and 30” Decks: Measure the belt spacing

at idler pulley. See Figure 3.4. The belt spacing

should be 1-1/4” but no less 1”. If the measurement

is less than 1”, the belt tension should be adjusted.

Refer to Section “BLADE DRIVE BELT

ADJUSTMENT”.

WARNING

The following procedure requires the engine and

blades to be operated. Exercise extreme caution.

Clear area of loose parts & tools first. Only operate

blades when seated in the operator’s seat.

IMPORTANT: The blade drive belt on 33” decks does

not require tension adjustment. If the belt becomes worn

or slack it must be replaced. Refer to Section “BLADE

DRIVE BELT REPLACEMENT”.

FIGURE 3.4

3.2.5. BLADE BRAKE

1. Check blade brake for proper function. Blade should

stop rotating in 3 seconds or less after moving the blade

control lever to the “OFF” position or after releasing the

blade pedals.

WARNING

Blades must stop rotating in 3 seconds or less after

the blade has been turned off. DO NOT operate

machine until blade brake has been adjusted and

functioning properly.

2. If the blade continues to rotate longer than 3

seconds do not operate machine. Refer to Section

“BLADE BRAKE ADJUSTMENT” or contact your

SNAPPER dealer for assistance.

3.2.6. SERVICE BRAKE / PARK BRAKE

1. Check machine brake for proper function. Engage

park brake. Push machine. Rear tires should skid. Drive

machine forward and apply brake. Machine should come

to a complete stop in less than 5 ft.

2. If brakes are not functioning properly brake

adjustment must be completed before operating

machine. Refer to Section “SERVICE BRAKE – PARK

BRAKE ADJUSTMENT”.

REMOVE FOUR (4)

SELF-TAPPING

SCREWS

REMOVE

COVER

BELT SPACING

SHOULD BE

1-1/4”

ENGINE

PULLEY

IDLER

PULLEY

MOWER

DECK

PULLEY

Section 3 – MAINTENANCE

3.2 SERVICE - AFTER FIRST 5 HOURS

3.2.7. SAFETY INTERLOCK SYSTEM CHECKS

Perform the following interlock system checks

periodically during the operating season. Contact your

authorized Snapper dealer if you have questions.

WARNING

DO NOT operate machine if any safety interlock or safety

device is not in place and functioning properly. DO NOT

attempt to defeat, modify or remove any safety device.

ENGINE MUST NOT START IF:

1) Clutch/Brake Pedal is not fully depressed OR,

2) Blade Control is in the “ON” (blades engaged)

position.

ENGINE SHOULD START IF:

1) Blade Control is in the “OFF” (blades

disengaged) position AND,

2) Clutch/Brake Pedal is fully depressed.

ENGINE AND BLADES MUST STOP IF:

1) Operator rises off of seat with Blade Control in

“ON” (blades engaged) position OR,

2) Operator rises off of seat with Clutch/Brake

Pedal not fully depressed.

3.2.8. REVERSE LOCKOUT MECHANISM

Check function of Reverse Lockout Mechanism with

engine off.

1. Depress and hold blade pedals.

2. Depress and hold clutch/brake pedal.

3. Shift lever must not go into reverse.

WARNING

DO NOT operate machine if Reverse Lockout

Mechanism is not functioning properly. Contact your

SNAPPER dealer immediately for assistance.

3.2.9. LUBRICATION – GREASE FITTINGS

The following components on the Rear Engine Rider are

equipped with grease fittings and require periodic

lubrication. Apply General Purpose grease (NLGI No.2)

with a grease gun.

1. Front Wheel Bearings. Refer to Section “FRONT

WHEEL BEARINGS – LUBRICATION”.

2. Rear Axle Bearing. Refer to Section “REAR AXLE

BEARING – LUBRICATION”.

3. Mower Blade Spindle. Refer to Section “MOWER

BLADE SPINDLE – LUBRICATION”.

4. Shift Lever. Refer to Section “SHIFT LEVER –

LUBRICATION”.

3.3 SERVICE - EVERY 25 OPERATING HOURS

Perform all service required after the first 5 hours of

operation. Refer to Section “SERVICE – AFTER 5

HOURS”.

3.3.1. CHECK ENGINE

1. Change engine oil. Refer to Section “CHANGE

ENGINE OIL”. Refer to engine owner's manual for oil

specification.

2. Change air filter. Pull up and rotate the air cleaner

latch to remove cleaner cover. See Figure 3.4.

IMPORTANT: When cover is removed, you are viewing the

carburetor side of the air filter, which will appear clean. Remove

filter and pre-cleaner for inspection.

FIGURE 3.4

3. Refer to engine owner's manual for cleaning and

service instructions. Remove and clean engine air pre-

cleaner. Remove and replace engine air cleaner. See

Figure 3.5. Install pre-cleaner and air cleaner per engine

owner’s manual.

FIGURE 3.5

4. Reinstall air cleaner cover. Insert tabs located at the

bottom of the cover into corresponding slots in engine

cover. Position cover and engage latch over cover and

rotate and push down to lock. IMPORTANT: The tabs

on the air cleaner cover must be completely inserted

into engine cover or the compartment will not be

completely sealed to prevent debris from entering into

the carburetor.

AIR CLEANER

COVER

AIR CLEANER

LATCH

AIR CLEANER

AIR PRE-

CLEANER

BRIGGS ENGINE SHOWN

Section 3 - MAINTENANCE

WARNING

DO NOT attempt any adjustments, maintenance or

service with the engine or blades running. Stop

blades. Stop engine. Engage parking brake. Remove

key. Remove spark plug wires from spark plugs and

(gas only) secure wires away from spark plugs.

Engine and components are HOT. Avoid serious

burns by allowing all parts sufficient time to cool.

Fuel Filler Cap and Vent must be closed securely to

prevent fuel spillage.

3.3 SERVICE - EVERY 25 OPERATING HOURS

3.3.2. BATTERY FLUID LEVEL

1. Remove battery. Refer to Section “BATTERY

REMOVAL”.

2. Remove battery caps. Check fluid level.

3. Add water only to bring fluid to proper level –

DO NOT OVERFILL.

4. Reinstall battery. Refer to Section “BATTERY

INSTALLATION”.

3.3.3. MOWER DECK LEVELNESS

Check mower deck for proper level. Adjust as required.

Refer to Section “MOWER DECK ADJUSTMENT –

LEVELNESS”.

3.3.4. CLEAN MOWER DECK

1. Follow WARNING statement found on this page.

2. Check fuel level in tank. If over 3/4 full, remove tank.

Refer to Section “REMOVING FUEL TANK”.

If 3/4 or less, proceed to next step.

3. Carefully stand Rear Engine Rider on rear bumper.

4. Clean underside of mower deck, removing all

accumulation of grass clippings and debris.

5. Clean top of deck, removing all grass clippings and

debris.

3.3.5 MOWER BLADE SPINDLE - LUBRICATION

1. Follow WARNING statement found on this page.

2. Check fuel level in tank. If over 3/4 full, remove tank.

Refer to Section “FUEK TANK REMOVAL”. If 3/4 or less,

proceed to next step.

3. Carefully stand Rear Engine Rider on rear bumper.

4. Lubricate spindle with three shots of general purpose

grease from grease gun. See Figure 3.5.

IMPORTANT: If the Rear Engine Rider will be on its

rear bumper for longer than two hours, remove the

battery. Refer to Section “BATTERY REMOVAL”.

3.3.6. MOWER DECK LINKAGE - LUBRICATION

Lubricate all mower deck linkage pivot points with a light

coat of motor oil.

FIGURE 3.5

3.3.7. FRONT WHEEL BEARING - LUBRICATION

1. Lubricate front wheel bearings with five shots of

general purpose grease, from grease gun. See

Figure 3.6.

FIGURE 3.6

3.3.7a. SHIFT LEVER - LUBRICATION

1. Lubricate shift lever fitting with two shots of

general purpose grease from grease gun. See

Figure 3.6a.

FIGURE 3.6a

FRONT WHEEL

GREASE FITTING

SPINDLE GREASE

FITTING

SHIFT LEVER

GREASE FITTING

Section 3 – MAINTENANCE

WARNING

DO NOT attempt any adjustments, maintenance,

service or repairs with the engine running. Stop

engine. Stop blade. Engage parking brake. Remove

key. Remove spark plug wire from spark plug and

secure away from plug. Engine and components are

HOT. Avoid serious burns, allow all parts to cool

before working on machine. Fuel Filler Cap and Vent

must be closed securely to prevent fuel spillage.

3.3 SERVICE - EVERY 25 OPERATING HOURS

3.3.8. REAR AXLE BEARING - LUBRICATION

1. The left rear axle bearing requires three shots of

general purpose grease from grease gun. See

Figure 3.7.

2. The right rear axle bearing is lubricated by the

differential lubricant and requires no grease.

FIGURE 3.7

3.3.9. DIFFERENTIAL/CHAIN CASE - LUBRICATION

1. Stand rear engine rider on its rear bumper and

check the fill/level plug, for cracks and wear. Replace

fill/level plug if signs of wear are visible.

IMPORTANT: If the Rear Engine Rider will be on its

rear bumper for longer than two hours, remove the

battery. Refer to Section “BATTERY REMOVAL”.

2. To check lubricant, remove fill/level plug and

visually inspect for lubricant on the internal parts of

the differential. If no lubricant is visible on the internal

parts of the differential, add transmission grease as

needed. See Figure 3.8.

IMPORTANT: Overfilling of the differential with lubricant

will cause lubricant to leak onto drive components of the

Rear Engine Rider.

FIGURE 3.8

3. Check fill/level plug for damage. If signs of wear or

cracks are visible, replace plug with new plug. See

Figure 3.9.

4. To check lubricant in chain case, remove

fill/level plug and look for lubricant on the internal

components of the chain case. If no lubricant is

visible, add SNAPPER transmission grease as

needed. See Figure 3.9.

FIGURE 3.9

3.3.10. Check “MAINTENANCE SCHEDULE”

Section of Engine Owner’s Manual for additional

engine service.

AXLE

BOOTS

CHAIN

CASE

FILL/LEVEL

PLUG

P.N. 1-1024

LEFT REAR

AXLE BEARING

GREASE

FITTING

PLUG

DIFFERENTIAL

Section 3 – MAINTENANCE

WARNING

DO NOT attempt any adjustments, maintenance,

service or repairs with the engine running. Stop

engine. Stop blade. Engage parking brake. Remove

key. Remove spark plug wire from spark plug and

secure away from plug. Engine and components

are HOT. Avoid serious burns, allow all parts to

cool before working on machine. Fuel Filler Cap

and Vent must be closed securely to prevent fuel

spillage.

3.4 SERVICE - ANNUALLY

3.4.1. ENGINE

1. Perform all maintenance as specified in

“MAINTENANCE SCHEDULE” Section of this

manual.

3.4.2. FUEL FILTER

Service fuel filter as instructed below, on COLD

ENGINE ONLY!

IMPORTANT: To stop flow of fuel, tank may be

removed from bracket and set on the floor so the fuel

level will be below the filter. Refer to Section

“REMOVING FUEL TANK”.

1. Remove hose clamps from fuel filter.

2. Remove fuel lines from filter. Discard filter.

3. Install new fuel filter. See Figure 3.10.

4. Reinstall fuel tank into bracket.

5. Carefully reinstall fuel clamps.

6. Check fuel system for leaks.

FIGURE 3.10

3.5 EVERY TWO YEARS

In addition to regular maintenance, the following

components of the Rear Engine Rider should be

carefully inspected every two years for wear or

damage. Replace worn or damaged parts with

genuine SNAPPER replacement parts available

from an authorized SNAPPER dealer.

3.5.1. All bushings and pivot areas.

3.5.2. Check both front wheel king pins.

3.5.3. Transmission shift lever and detent.

3.5.4. Clutch disc.

3.5.5. Clutch Yoke.

3.5.6. Mower deck linkage and pivot areas.

3.6 STORAGE (OUT OF SEASON)

If desired, the Rear Engine Rider can be stored on

the rear bumper. Perform the following procedures

to insure the Rear Engine Rider will operate

properly when taken out of storage.

3.6.1. Thoroughly clean the Rear Engine Rider by

removing all grass clippings and debris.

3.6.2. Perform maintenance and lubrication as

required.

3.6.3. Drain fuel from fuel tank.

3.6.4. Start engine and allow it to run until engine

runs out of fuel. This allows the carburetor and

fuel system to remain clean during storage.

3.6.5. Remove battery. Refer to Section

“BATTERY STORAGE”.

3.6.6. Close vent on fuel filler cap.

3.6.7. Carefully stand Rear Engine Rider on rear

bumper in desired location for storage.

3.7 REMOVING FUEL TANK

Before removing fuel tank from rear engine rider,

move rider outdoors where fumes can be easily

dissipated. Removal of the tank is accomplished

from the left side of the machine by pulling the

tank straight up and away from the fuel tank

bracket. Holding the fuel tank, remove the fuel

filler cap and pour remaining fuel in an approved

container. See Figure 3.11.

FIGURE 3.11

FUEL

FILLER

CAP

FUEL

TANK

FUEL TANK

BRACKET

FUEL

TANK

FUEL

FILTER

HOSE

CLAMPS

P.N. 1-4359

Section 4 - ADJUSTMENTS & REPAIR

WARNING

DO NOT attempt any adjustments, maintenance,

service or repairs with the engine running. Stop

engine. Stop blade. Engage parking brake. Remove

key. Remove spark plug wire from spark plug and

secure away from plug. Engine and components are

HOT. Avoid serious burns, allow all parts to cool

before working on machine. Fuel Filler Cap and Vent

must be closed securely to prevent fuel spillage.

4.1 ENGINE ADJUSTMENTS & REPAIR

Refer to the engine owner’s manual for those

adjustments and/or repairs that can be made by the

owner.

4.2 MOWER DECK & COMPONENT ADJUSTMENTS

The following mower deck and component

adjustments and repairs can be made by the

owner. However, if there is difficulty in achieving

these adjustments and repairs, it is recommended

that these repairs be made by an authorized

SNAPPER dealer.

WARNING

Once blade is disengaged it should come to a stop

in 3 seconds or less. If the blade continues to rotate

after 3 seconds the blade brake must be adjusted.

DO NOT continue to operate the machine if the blade

brake is not operating properly.

4.2.1. BLADE BRAKE ADJUSTMENT

The automatic Blade Brake should stop the blades

within 3 seconds anytime the blades are

disengaged by moving blade lever to the "OFF"

position or by releasing the Blade Pedals. When

the Blade Brake is properly adjusted there should

be 3” to 3-1/4" clearance between the Blade

Engagement Lever and the edge of the Latch

Plate. Check this by disengaging the Blade Lever

as shown in Figure 4.1. Perform the following

measurement and adjustment.

1. With the blade engagement lever disengaged,

measure the distance between the front of the

blade lever and the edge of the latch plate. The

dimension should be 3” to 3-1/4" clearance

between lever and edge of plate. See Figure 4.1.

If the dimension is incorrect go to step 2.

2. Remove Belt Cover. Refer to Section “BLADE

BELT COVER REMOVAL”.

3. If dimension is greater than 3-1/4”, rotate nut

clockwise to increase brake tension. If dimension

is less than 3”, rotate nut counter-clockwise to

decrease brake tension. See Figure 4.2.

4. Reinstall belt cover and tighten bolts securely.

WARNING

DO NOT operate machine until blade brake is

adjusted and functioning properly. If blade stop time

can not be achieved with the adjustment procedure

described above, take machine immediately to an

authorized Snapper dealer.

FIGURE 4.1

FIGURE 4.2

(Continued on Next Page)

ROTATE NUT CLOCKWISE TO

INCREASE BRAKE TENSION.

ROTATE NUT COUNTER-

CLOCKWISE TO DECREASE

BRAKE TENSION.

3” to 3-1/4”

CLEARANCE

MEASURE FROM

THIS EDGE

BLADE

LEVER

DISENGAGED

Page is loading ...

Snapper 331723BVE (7084954) User manual

Brand: Snapper

Model: 331723BVE (7084954)

Category: Lawnmowers

Type: User manual

Download PDF

report

Snapper 331723BVE (7084954) User manual

Snapper 331723BVE (7084954) User manual

Related papers

Other documents