Simplicity SB60V BLOWER, 60V User manual

Brand: Simplicity

Model: SB60V BLOWER, 60V

Category: Power tools

Type: User manual

This manual is also suitable for

SB60V

ENGLISH ESPAÑOL

60V Axial Blower

Model SB60V

Please do not return product to retailer.

Por favor, no devuelva el producto al lugar de compra.

1-800-317-7833

www.snapper.com

Instruction Manual

Manual de Instrucciones

Rev. 01 11/15/15

Briggs & Stratton Power Products Group, LLC

Milwaukee, WI, USA

ADVERTENCIA:

Read and follow all Safety Rules and Operating Instructions before

using this product. Failure to do so can result in serious injury.

Lea el manual de instrucciones y siga todas las advertencias e

instrucciones de seguridad. El no hacerlo puede resultar en

lesiones graves.

WARNING

Not for Reproduction

CONTENTS

SYMBOL NAME DESIGNATION/EXPLANATION

Volts Voltage

Amperes Current

Hz Hertz Frequency (cycles per second)

Watts Power

min Minutes Time

Alternating Current Type of current

Direct Current Type or a characteristic of current

/min

Per Minute

Revolutions, strokes, surface speed, orbits etc.,

per minute

Wet Conditions Alert Do not expose to rain or use in damp locations

Read The Operator’s Manual

To reduce the risk of injury user must read and

understand operator’s manual before using this

product.

Wear Eye Protection

Always wear eye protection with side shields

marked to comply with ANSI Z87.1 with

operating this equipment

Safety Alert Precautions that involve your safety.

Long Hair

Failure to keep long hair away from the air inlet

could result in personal injury.

Loose Clothing

Failure to keep loose clothing from being drawn

into air intake could result in personal injury.

Keep Bystanders Away Keep all bystanders at least 50 ft. away.

Blower Tubes Do not operate without tubes in place.

Impeller Blades

Rotating impeller blades can cause severe

injury.

IDENTIFICATION OF SAFETY SYMBOLS

Identication of Safety Symbols 2

Product Specications 3

Safety Rules 4

Assembly 7

Operation 9

Maintenance 11

Troubleshooting Table 12

Exploded View 13

Parts List 14

Limited Warranty Statement 15

Not for Reproduction

The following signal words and meanings are intended to explain the levels of risk associated

with this product.

Symbol Name Designation/Explanation

DANGER

Indicates an imminently hazardous situation, which, if not

avoided, could result in death or serious injury.

WARNING

Indicates a potentially hazardous situation, which, if not avoided,

could result in death or serious injury.

CAUTION

Indicates a potentially hazardous situation, which, if not avoided,

may result in minor or moderate injury.

CAUTION

(Without Safety Alert Symbol) Indicates a situation that may

result in property damage.

IDENTIFICATION OF SAFETY SYMBOLS

SPECIFICATIONS

Motor: 60v Brushless Motor

Air Volume: 450 CFM

Air Speed (Max): 120 MPH

Speed Control: Variable Speed (with Cruise Control)

Unit Weight (without battery): 5.1 lbs

Unit Weight (with battery): 7.4 lbs

Included Battery Pack: SBA2560V

Charger: SCH60V

Compatible Battery Packs (sold separately):

SBA260V - 60V 2 Ah Battery

SBA2560V - 60V 2.5 Ah Battery

SBA460V - 60V 4 Ah Battery

Not for Reproduction

GENERAL SAFETY RULES

READ ALL INSTRUCTIONS

READ AND UNDERSTAND ALL

INSTRUCTIONS. Failure to follow all

instructions listed below may result in electric

shock, re and/or serious personal injury.

WARNING:

When using this device,

safety precautions must be followed. For your

own safety and that of bystanders, please

read these instructions before operating the

device. Do not use the device without reading

the instruction manual. Please keep the

instruction manual safe for later use.

READ ALL INSTRUCTIONS

BEFORE USING (THIS BLOWER)

• Do not leave appliance plugged in. Unplug

from outlet when not in use and before

servicing.

• Do not allow to be use as a toy. Close

attention is necessary when used by or

near children.

• Use only as described in this manual.

Use only manufacturer’s recommended

attachments.

• Do not use with a damaged plug or cord. If

the tool is not working as it should, or if it

has been dropped, damaged, left outdoors,

or dropped into water, return it to an

authorized service centre.

• Do not pull or carry by the cord, use the

cord as a handle, close a door on a cord,

or pull the cord around sharp edges or

corners. Do not run appliances over the

cord. Keep the cord away from heated

surfaces.

• Do not unplug by pulling on the cord. To

unplug, grasp the plug, not the cord.

• Do not handle the plug or any other

appliances with wet hands.

• Do not put any object into openings. Do

not use with any opening blocked. Keep

openings free of dust, lint, hair, and

anything that may reduce air ow.

• Keep hair, loose clothing, ngers and

all body parts away from openings and

moving parts.

• Turn off all controls before unplugging.

• Use extra care when cleaning on stairs.

• Do not use to pick up ammable or

combustible liquids, such as gasoline, or

use in areas where they may be present.

WHEN USING (THIS BLOWER)

• Do not operate power tools in an explosive

atmosphere, such as in the presence of

ammable liquids, gases, or dust. Power

tools create sparks that may ignite the dust

or fumes.

• To reduce the risk of electric shocks, this

tool has a polarized plug (one blade is

wider than the other) and will require the

use of a polarized extension cord. The

plug will only t into a polarized extension

cord one way. If the plug does not t fully

into the extension cord, reverse the plug.

If the plug still does not t, obtain a correct

polarized extension cord. A polarized

extension cord will require the use of a

polarized wall outlet. This plug will only t

into the polarized wall outlet one way. If the

plug does not t fully into the wall outlet,

reverse the plug. If the plug still does not

t, contact a qualied electrician to install

the proper wall outlet. Do not change the

equipment plug, extension cord receptacle,

or extension cord plug in any way.

• Avoid body contact with grounded surfaces

such as pipes, radiators, ranges, and

refrigerators. There is an increased risk of

electric shock if your body is grounded.

• Do not expose power tools to rain or wet

conditions. Water entering a power tool will

increase the risk of electric shock--Store

indoors.

• Do not handle or plug-in tools with wet

hands.

• Never allow children to operate the

equipment. Never allow adults to operate

the equipment without proper instruction.

• Wear eye protection that is marked to

comply with ANSI Z87.1 when operating

this product.

• Wear heavy long pants, boots, and gloves.

Avoid loose garments or jewellery that

could get caught in moving parts of the

machine or its motor.

• Do not force the tool. Use the correct tool

for your application. The correct tool will

work more efciently and safely when it

is used at the rate that it was designed to

work at.

• Do not operate the equipment while

barefoot or when wearing sandals or similar

lightweight footwear. Wear protective

footwear that will protect your feet and

improve your footing on slippery surfaces.

• Secure long hair so it is above shoulder

level to prevent entanglement in any

moving parts.

• Keep rm footing and balance. Do not

overreach. Overreaching can result in loss

of balance.

• Do not allow children or untrained

individuals to use this unit.

• Avoid accidental start-ups. Be sure the

power switch is not on before plugging in.

Turn off power switch before unplugging.

• Do not use the tool if the switch does not

turn it on or off. Any tool that cannot be

Not for Reproduction

controlled with the switch is dangerous,

and must be repaired.

• Do not leave the tool unattended when

plugged in. Unplug from the power outlet

when not in use, before servicing, and

before storing the tool. Such preventative

safety measures reduce the risk of starting

the tool accidentally.

• Keep all bystanders, children, and pets at

least 50’ (15 m) away.

• For household use only.

• Use only Snapper batteries (Model

SBA260V, SBA2650V, and SBA460V)

• Do not operate this unit when you are tired,

ill, or under the inuence of alcohol, drugs,

or medication.

• Do not operate in poor lighting.

• Keep all parts of your body away from any

moving parts and all hot surfaces of the

unit.

• Do not put any object into openings. Do

not use with any opening blocked. Keep

openings free of dust, lint, hair, and

anything that may reduce air ow.

• Check the work area before each use.

Remove all objects that can be thrown or

become entangled in the machine, such as

rocks, broken glass, nails, wire, or string.

• Use only identical manufacturer’s

replacement parts and accessories. Use

of any other parts may create a hazard or

cause product damage.

FOR BATTERY-OPERATED APPLIANCE

• Prevent unintentional starting. ensure

the switch is in the off-position before

connecting to battery pack, picking up

or carrying the appliance. carrying the

appliance with your nger on the switch or

energizing appliance that have the switch

on invites accidents.

• Disconnect the battery pack from the

appliance before making any adjustments,

changing accessories, or storing appliance.

Such preventive safety measures

reduce the risk of starting the appliance

accidentally.

• Recharge only with the charger specied

by the manufacturer. A charger that is

suitable for one type of battery pack may

create a risk of re when used with another

battery pack.

• Use appliances only with specically

designated battery packs. Use of any other

battery packs may create a risk of injury

and re.

• When battery pack is not in use, keep it

away from other metal objects, like paper

clips, coins, keys, nails, screws or other

small metal objects, that can make a

connection from one terminal to another.

Shorting the battery terminals together

may cause burns or a re.

• Under abusive conditions, liquid may be

ejected from the battery; avoid contact.

If contact accidentally occurs, ush with

water. If liquid contacts eyes, additionally

seek medical help. Liquid ejected from the

battery may cause irritation or burns.

• Do not use a battery pack or appliance

that is damaged or modied. Damaged

or modied batteries may exhibit

unpredictable behavior resulting in re,

explosion or risk of injury.

• Do not expose a battery pack or appliance

to re or excessive temperature. Exposure

to re or temperature above 212°C may

cause explosion.

• Have servicing performed by a qualied

repair person using only identical

replacement parts. This will ensure that the

safety of the product is maintained.

SAVE THESE INSTRUCTIONS

SERVICE

Tool service must be performed only by

qualied repair personnel. Service or

maintenance performed by unqualied

personnel may result in a risk of injury. Please

call 1-800-317-7833 for customer support.

GENERAL SAFETY RULES

Not for Reproduction

GENERAL SAFETY RULES

CHILD SAFETY

Tragic accidents can occur if the operator is

not aware of the presence of children.

• Keep children out of the working

area and under the watchful care of a

responsible adult.

• Do not allow children under the age

of 14 to operate this blower. Children

who are 14 years of age and older must

read and understand the operating

instructions and safety rules in this

manual and must be trained and

supervised by a parent.

• Stay alert, and turn the blower off if a

child or any other person enters the

working area.

• Use extreme care when approaching

blind corners, doorways, shrubs, trees,

or other objects that may obscure your

view of a child who may run into the

path of the blower.

WARNING:

(PROPOSITION 65)

Some dust created by power sanding, sawing,

grinding, drilling, and other construction

activities contains chemicals known to cause

cancer, birth defects or other reproductive

harm. Some examples of these chemicals

are:

• Lead from lead-based paints

• Crystalline silica from bricks and cement

and other masonry products, and

• Arsenic and chromium from chemically

treated lumber.

Your risk of exposure to these chemicals

varies depending on how often you do this

type of work. To reduce your exposure to

these chemicals, work in a well-ventilated

area, and work with approved safety

equipment, such as dust masks that are

specially designed to lter out microscopic

particles.

SAVE THESE INSTRUCTIONS

Not for Reproduction

ASSEMBLY

PART NAME FIGURE QTY

60V Blower

Blower Tube

60V 2.5Ah Battery

60V Charger

Operator’s

Manual

Pleasedo not return product to retailer.

Porfavor,n od evuelva el producto al lugard ec ompra.

Veuillezne pasr etourner le produi ta ud étaillant.

1-800-317-7833

www.snapper.com

WARNING:

ADVERTENCIA:

AVERTISSEMENT:

Lirele manuel d’instructions et bien respectert ousl es avertisse-

mentsett outesl esinstructions de sécurité.Toutdé fautde lefa ire

pourraitentraînerd es blessuresg raves.

OÑ

APS

EHS

ILG

Briggs & Stratton Power Products Group, LLC

Milwaukee, WI, USA

InstructionM anual

Manuald eI nstrucciones

Manueld ’Instructions

Read and follow all Safety Rules and Operating Instructions before

using this product. Failure to do so can result in serious injury.

Lea el manual de instrucciones y siga todas las advertencias e

instrucciones de seguridad. El no hacerlo puede resultar en

lesiones graves.

60V LITHIUM-ION

CORDLESS STRING TRIMMER

Model ST60V

Rev. 00 07/30/15

Quick

Start Guide

QUICK START GUIDE

60V LITHIUM-ION

BRUSHLESS STRING TRIMMER

ST60V

ATTACHING THE GUARD

Missing parts, accessories or need a service center?

Do Not Return to Store

Call: 1-800-317-7833 www.snapper.com

1. Invert the string trimmer to access the

trimmer head.

2. Remove supplied screws (1) from the

trimmer head (4) with a philips

screwdriver (not included).

3. Place the guard (2) on to the trimmer

head.

4. Align the screw holes (3) on the guard

with the screw holes on the trimmer head.

5. Insert the screws into the trimmer

head, fastening the guard in place using a

Phillps head screwdriver (not included).

ATTACHING THE AUXILIARY HANDLE

INSTALLING AN ATTACHMENT TO THE POWER HEAD

Note: Remove the rubber insert that is

located in the shaft prior to assembling

the string trimmer.

1. Loosen the attachment knob (1) on the

coupler (5).

2. Push in the release button (2) located

on the attachment shaft (3). Align the

release button with the positioning hole

(4) and slide the two shafts together.

Rotate the attachment shaft until the

button locks into the positioning hole.

3. Tighten the attachment knob securely.

1. Press the auxiliary handle (1) onto the

power head shaft so that the handle is

angled toward the rear handle that allows

for comfortable operation.

2. Slide the auxiliary handle over the

holder (2) and ensure the holder fits

between the slots on the auxiliary handle.

3. Align the holes on the auxiliary handle

with the holes on holder.

4. Insert the handle knob (3) through the

auxiliary handle.

5. Tighten until there is no movement in

the handle.

STARTING/STOPPING THE TRIMMER

1. Ensure a fully charged battery is

installed into the string trimmer.

2. Place one hand on the trigger handle.

Place the other hand on the auxiliary

handle.

3. Press and hold the lock-out button (2)

and squeeze the switch trigger (1). The

string trimmer will turn ON.

4. Release the lock-out button. The string

trimmer will stay on as long as the switch

trigger is held.

5. Release switch trigger to stop.

LOOSEN

TIGHTEN

WARNING:

This Quick Start Guide is not a substitute for reading the operator's manual. To reduce the risk of injury or death, user

must read and understand the operator's manual before using this product.

PACKING LIST

WARNING:

Read and understand

entire Operator’s Manual and follow all

warnings and instructions. Failure to follow all

instructions may result in electric shock, re

and/or serious personal injury.

UNPACKING

This product requires assembly.

• Carefully remove the product and any

accessories from the box. Make sure that all

items listed in the packing list are included.

• Inspect the tool carefully to make sure

no breakage or damage occurred during

shipping.

• Do not discard the packing material until you

have carefully inspected and satisfactorily

operated the tool.

• If any parts are damaged or missing, please

call 1-800-317-7833.

WARNING:

Do not use this product

if any parts on the packing list are already

assembled to your product when you unpack

it. Parts on this list are not assembled to the

product by the manufacturer and require

customer installation. Use of a product that

may have been improperly assembled could

result in serious personal injury.

WARNING:

If any parts are

damaged or missing, do not operate this

product until the parts are replaced. Use of

this product with damaged or missing parts

could result in serious personal injury.

WARNING:

Do not attempt to

modify this product or create accessories not

recommended for use with this string trimmer.

Any such alteration or modication is misuse

and could result in a hazardous condition

leading to possible serious personal injury.

WARNING:

Do not install the

battery until assembly is complete. Failure to

comply could result in accidental starting and

possible serious personal injury.

Not for Reproduction

ASSEMBLY

BATTERY INSTALLATION

1. Align the battery with the battery opening.

2. Grasp the blower handle rmly.

3. Insert the battery into the battery opening

until the battery release button locks into

place.

4. Push down on the battery until it locks into

place. You should hear a "click" once it is

installed.

BATTERY REMOVAL

1. Press the battery release button. This will

cause the battery to raise out of the tool.

2. Grasp the blower handle rmly. Pull the

battery pack out of the handle.

NOTE: The battery pack ts snugly into the

handle to prevent accidental dislodging. It

may require a strong pull to remove.

IMPORTANT: The battery is not shipped fully

charged. It is recommended that the battery be

fully charged before initial use. With regular

use, the battery pack will take 1 hours or less

to fully charge. It is recommended that the

battery be charged every 3 months when the

blower is not in use.

BLOWER TUBE ASSEMBLY

WARNING:

To prevent accidental

starting that could cause serious personal

injury, always remove the battery pack from

the tool when assembling parts.

1. Align either of the grooves on the tube with

the tabs on the blower housing. Slide the tube

onto the blower housing until the tab engages

the grooves.

2. Turn the tube in the direction of the arrow

until both of the tabs slide into the lock

positions.

Battery release button

GrooveTube

Tab

Lock

osition

LockUnlock

Not for Reproduction

OPERATION

KNOW YOUR AXIAL BLOWER(See Figure 1)

The safe use of this product requires an understanding of the information in this instruction

manual as well as a knowledge of the project you are attempting. Before using this product,

familiarize yourself with all operating features and safety rules.

TRIGGER

Starts/stops the ow of air through the blower.

BATTERY RELEASE BUTTON

Releases the battery pack from the blower

BLOWER TUBE

The blower tube can be easily installed on the blower without any additional tools.

CRUISE CONTROL LEVER

Allows you to lock-in the desired air ow.

Fig. 1

60-volt Lithium-Ion

Battery

Switch Trigger

Battery Release Button

Blower Tube

Cruise Control Lever

Not for Reproduction

WARNING:

Do not allow familiarity

with this product to make you careless.

Remember that a careless fraction of a

second is sufcient to inict serious injury.

WARNING:

Do not use any

attachments or accessories not recommended

by the manufacturer of this product. The

use of attachments or accessories not

recommended can result in serious personal

injury. Before each use, inspect the entire

product for damaged, missing, or loose

parts, such as screws, nuts, bolts, caps,etc.

Securely tighten all fasteners and caps and

do not operate this product until all missing or

damaged parts are replaced.

APPLICATION

You may use this product for the purposes

listed below:

• Clearing hard surfaces such as driveways

and walkways.

• Keeping decks and driveways free from

leaves and pine needles.

CHARGE BEFORE FIRST USE.

WARNING:

Always remove

battery pack from the product when you

are assembling parts, making adjustments,

cleaning, or when not in use. Removing

battery pack will prevent accidental starting

that could cause serious personal injury.

STARTING/STOPPING THE BLOWER

(See Figure 2)

• Ensure that the battery is installed in the

blower.

• Squeeze the trigger to start the blower.

• Release the trigger to stop.

NOTE: This blower has a variable speed

trigger. To decrease the speed slowly release

the trigger switch to desired speed.

OPERATION

OPERATING THE BLOWER

• To keep from scattering debris, blow

around the outer edges of a debris pile.

Never blow directly into the center of a

pile.

• To reduce sound levels, limit the number of

pieces of equipment used at any one time.

• Use rakes and brooms to loosen debris

before blowing. In dusty conditions, slightly

dampen surfaces when water is available.

• Conserve water by using power blowers

instead of hoses for many lawn and

garden applications, including areas such

as gutters, screens, patios, grills, porches,

and gardens.

• Watch out for children, pets, open

windows, or cars, and blow debris safely

away.

• After using blowers or other equipment,

clean up. Dispose of debris properly.

Trigger

Fig. 2

CRUISE CONTROL LEVER (See Figure 3)

• Move the cruise control lever toward the

rear of the blower. This will increase the

air speed and ow.

• Release the cruise control lever once it

has reached the desire air speed.

• To stop the blower, move the cruise control

lever completely forward.

Fig. 3

INCREASE

DECREASE/

OFF

Not for Reproduction

MAINTENANCE

WARNING:

In order to avoid personal injury and

the risk of re and electric shock, remove the

battery pack before adjusting, inspecting, or

cleaning the blower.

CLEANING

Remove the battery pack.

1. Brush or blow dust and debris out of the

air vents using compressed air or a vacuum.

Keep the air vents free of obstructions,

sawdust, and wood chips. Do not spray, wash,

or immerse the air vents in water.

2. Wipe off the housing and the plastic

components using a moist, soft cloth. Do

not use strong solvents or detergents on the

plastic housing or plastic components. Certain

household cleaners may cause damage, and

may cause a shock hazard.

BATTERY PACK

• Store the battery pack charged.

• Once the charging light turns green,

remove the battery from the charger and

disconnect the charger from the outlet.

• Recharge the battery pack anytime you

have notice there is less power. Never

let the battery pack become completely

discharged.

• After charging, the battery pack may

be stored in the charger as long as the

charger is not plugged in.

Not for Reproduction

PROBLEM POSSIBLE CAUSE SOLUTION

Unit will not start.

1. Battery is not secure.

1. To secure the battery pack, make

sure the battery is fully secured in the

blower. Refer to Installing the Battery

section in this manual.

2. Battery is not charged.

2. Charge the battery pack according

to the instructions included with your

model.

3. Defective power switch.

3. Call 1-800-317-7833 for technical

service.

The unit will start, but air will

not ow through the tube.

Blocked tube.

Inspect the intake vent and blower

tube for any blockage of air ow. If so,

remove the blockage.

Cruise Control Lever doesn't

work.

The screw is loose.

Tighten the screw with a phillips head

screwdriver.

TROUBLESHOOTING TABLE

WARNING:

Always stop unit and remove the battery before performing all of the

recommended remedies below except remedies that require operation of the unit

Not for Reproduction

EXPLODED VIEW

Not for Reproduction

PARTS LIST

ITEM NO. PART NO. DESCRIPTION QTY

1 34103811A Blower Tube 1

2 311011943 Blower Assembly 1

3 341051809B Rear Vent Housing 1

4 3220505A Rear Vent Screws 4

5 211011351 Battery 1

6 211011332 Charger 1

Not for Reproduction

LIMITED WARRANTY

Sunrise Global Marketing, LLC hereby

warranties this product, to the original

purchaser with proof of purchase, for a

period of four (4) years against defects in

materials, parts or workmanship.

Sunrise Global Marketing, LLC, at its own

discretion will repair or replace any and all

parts found to be defective, through normal

use, free of charge to the customer. This

warranty is valid only for units which have

been used for personal use that have not

been hired or rented for industrial/ commercial

use, and that have been maintained in

accordance with the instructions in the

owners’ manual supplied with the product

from new.

Battery and charger carries a two (2) years

warranty against defects in workmanship

and materials. Batteries must be charged

in accordance with the operator’s manuals

directions and regulations in order to be valid.

Brushless motor carries a ten (10) year motor

warranty against defects in workmanship and

materials.

Items not covered by warranty:

1. Any part that has become inoperative due

to misuse, commercial use, abuse, neglect,

accident, improper maintenance, or alteration;

2. The unit, if it has not been operated and/

or maintained in accordance with the owner's

manual; or

3. Normal wear, except as noted below;

4. Routine maintenance items such as

lubricants, blade sharpening;

5. Normal deterioration of the exterior nish

due to use or exposure.

Snapper helpline

Warranty service is available by calling the

Snapper toll-free helpline, 9 a.m. to 5 p.m.

EST. at 1-800-317-7833

Transportation Charges:

Transportation charges for the movement

of any power equipment unit or attachment

are the responsibility of the purchaser. It

is the purchaser’s responsibility to pay

transportation charges for any part submitted

for replacement under this warranty unless

such return is requested in writing by Sunrise

Global Marketing, LLC.

Not for Reproduction

ÍNDICE

SÍMBOLO NOMBR E DESIGNACIÓN/EXPLICACIÓN

Voltios Voltaje

Amperios Corriente

Hz Hertz Frecuencia (ciclos por segundo)

Vatios Potencia eléctrica

min Minutos Tiempo

Corriente alterna Tipo de corriente

Corriente directa Tipo o característica de la corriente

/min

Por minuto

Revoluciones, carreras,velocidad supercial,

órbitas, etc. por minuto

Alerta de condiciones

húmedas

No la exponga a la lluvia ni la use en lugares

húmedos o mojados

Lea el manual del operador

Para reducir el riesgo de lesiones el usuario

debe leer y comprender el manual del operador

antes de usar el producto.

Protección de los ojos y los

oídos

Lleve siempre protección ocular con placas

laterales que lleven la marca de conformidad

ANSI Z87.1 y protección para los oídos cuando

utilice este equipo.

Alerta de seguridad Precautions that involve your safety.

Cabello largo

Si no se mantiene alejado el cabello largo de la

entrada de aire se podrían provocar lesiones

personales.

Ropa suelta

Si no se evita que la ropa suelta sea succionada

hacia la entrada de aire se podrían provocar

lesiones personales.

Mantenga alejados a los

espectadores

Mantenga a todos los espectadores a 15 m. (50

pies) de distancia por lo menos.

Tubo de soplado No opere sin los tubos en su lugar.

Impeller Blades

Las palas del rotor en movimiento pueden

causar lesiones graves.

SÍMBOLOS

Identication of Safety Symbols 16

Especicaciones del producto 17

Reglas generales de seguridad 18

Ensamblaje 21

Funcionamiento 24

Mantenimiento 25

Resolución de averías 26

Diagrama de componentes 27

Lista de piezas 28

Garantía 29

Not for Reproduction

SÍMBOLOS

ESPECIFICACIONES

Motor: Motor sin escobillas de 60 V

Volumen de aire: 450 CFM

Velocidad del aire (Max): 120 MPH

Control de velocidad: Velocidad variable (con control de velocidad)

Peso (sin batería): 5.1 lbs

Peso da la unidad con la batería: 7.4 lbs

Incluye paquete de la batería: SBA2560V

Cargador: SCH60V

Baterías compatibles (se venden por

separado):

SBA260V - 60V 2 Ah Batería

SBA2560V - 60V 2.5 Ah Batería

SBA460V - 60V 4 Ah Batería

Los siguientes rótulos y signicados se usan para explicar el nivel de riesgo relacionado con

este producto.

SÍMBOLO AVISO SIGNIFICADO

DANGER

Indica situaciones inminentemente peligrosas que, si no se

evitan, resultan en la muerte o en lesiones serias.

ADVERTENCIA

Indica situaciones potencialmente peligrosas que, si no se

evitan, podrían resultar en la muerte o en lesiones serias.

PRECAUCIÓN

Indica situaciones potencialmente peligrosas que, si no

se evitan, podrían resultar en lesiones entre mínimas y

moderadas.

PRECAUCIÓN

(Sin el símbolo de alerta por seguridad) indica una

situación que podría resultar en daños a la propiedad.

Not for Reproduction

REGLAS GENERALES DE SEGURIDAD

ADVERTENCIA:

VEUILLEZ

LIRE ET ASSIMILER LES PRÉSENTES

INSTRUCTIONS.Toute négligence à l'égard

des instructions fournies ci-après peut

être la cause d’un choc électrique, d’un

incendie ou d’un grave accident corporel.

ADVERTENCIA:

Al utilizar este

dispositivo, debe seguir las siguientes

instrucciones de seguridad. Por su propia

seguridad y la de los que le rodean, lea estas

instrucciones antes de utilizar el aparato. No

use el dispositivo sin haber leído el manual

de instrucciones. Conserve el manual de

instrucciones para futuras referencias.

LEA TODAS LAS INSTRUCCIONES

ANTES DEL PRIMER USO (DEL APARATO)

• Preste atención al aparato cuando esté

enchufado. Desenchufe el aparato de

la toma de corriente cuando no esté en

uso y antes de cualquier operación de

mantenimiento. No utilizar en el exterior o

sobre supercies mojadas.

• No permita que se utilice como juguete. Es

necesario prestar mucha atención cuando

se utiliza cerca de niños.

• Utilizar únicamente como se describe en

este manual. Utilice sólo los complementos

recomendados por el fabricante.

• No utilice un conector dañado. Si el

aparato no funciona como debería o si se

ha caído, se ha dañado, se ha dejado al

aire libre o se ha caído en agua, llévelo a

un centro de servicio autorizado.

• No tire ni lleve por el cable el aparato,

no use el cable como asa, no cierre una

puerta sobre el cable o pase el cable por

supercies y esquinas aladas. No use el

aparato sobre el cable. Mantenga el cable

lejos de supercies calefactadas.

• No desconecte el aparato tirando del

cable. Para desenchufar, tire el enchufe,

no del cable.

• No toque el enchufe ni ningún otro aparato

con las manos mojadas.

• No coloque ningún objeto en las aberturas.

No utilice con cualquier abertura

bloqueada. Mantenga las aberturas libres

de polvo, pelusas, pelo y cualquier cosa

que pueda reducir el ujo de aire.

• Mantenga el cabello, la ropa suelta, los

dedos y todas las partes del cuerpo

alejados de las aberturas y piezas móviles.

• Desactive todos los controles antes de

desenchufar.

• Tenga especial cuidado al limpiar en las

escaleras.

• No use el aparato para recoger líquidos

combustibles o inamables, tales como

gasolina, ni en áreas donde estos puedan

estar presentes.

DURANTE EL USO (DEL APARATO)

• No opere herramientas eléctricas en

entornos explosivos, por ejemplo ante la

presencia de líquidos, gases o aserrín

inamables. Las herramientas eléctricas

producen chispas que podrían incendiar el

aserrín o los vapores.

• Para reducir el riesgo de descarga

eléctrica, esta herramienta tiene un

enchufe polarizado (una lámina es más

ancha que la otra) y requiere el uso de

un cable de extensión polarizado. El

enchufe encajará en un cable de extensión

polarizado de una sola manera. Si el

enchufe no entra completamente en el

cable de extensión, invierta el enchufe. Si

el enchufe sigue sin encajar, obtenga un

cable de extensión polarizado adecuado.

Un cable de extensión polarizado

requerirá el uso de una toma de corriente

polarizada. Este enchufe encajará en

la toma de corriente polarizada de una

sola manera. Si el enchufe no encaja

completamente en la toma de corriente,

invierta el enchufe. Si el enchufe sigue

sin encajar, póngase en contacto con un

electricista cualicado para que instale la

toma de corriente adecuada. No cambie

el enchufe del equipo, el receptáculo del

cable de extensión o el enchufe del cable

de extensión de ninguna manera.

• Evite el contacto corporal con supercies

conectadas a tierra, como tuberías,

radiadores, estufas y refrigeradores. Existe

un mayor riesgo de descargas eléctricas si

su cuerpo está conectado a tierra.

• No exponga las herramientas eléctricas a

la lluvia o humedad. Si entra agua en una

herramienta eléctrica podría aumentar el

riesgo de descargas eléctricas. Almacenar

en interior.

• No manipule o conecte las herramientas

con las manos mojadas.

• No manipule o conecte las herramientas

con las manos mojadas. No permita que

los niños utilicen el equipo. No permita

que ningún adulto utilice este equipo sin la

debida instrucción.

• Use protección ocular y auditiva que

cumplan la norma ANSI Z87.1 al utilizar

este producto.

• Use guantes, botas y pantalones

resistentes. Evite usar ropa holgada o joyas

que podrían engancharse en las piezas

móviles de la máquina o de su motor.

• No fuerce la herramienta. Utilice la

herramienta correcta para su aplicación.

El aparato funcionará de manera más

Not for Reproduction

eciente y segura si se utiliza según el

ritmo para el que fue diseñado.

• No utilice el equipo mientras está descalzo

o cuando lleve sandalias o un calzado

ligero similar. Utilice calzado de protección

que proteja sus pies y mejore su agarre en

supercies resbaladizas.

• Recoja el cabello largo para que quede por

encima del nivel de los hombros y evitar

así que se enmarañe en cualquier pieza

móvil.

• Manténgase rme y equilibrado. No realice

sobreesfuerzos. Una sobreextensión

puede resultar en la pérdida del equilibrio.

• No permita que niños o individuos sin

experiencia utilicen este aparato.

• Evite el arranque accidental. Asegúrese de

que el interruptor no está activado antes de

enchufar. Apague el botón de encendido

antes de desenchufarlo.

• No utilice la herramienta si el interruptor

no enciende ni apaga. Cualquier

herramienta que no puede ser controlada

con el interruptor es peligrosa y debe ser

reparada.

• No deje el aparato descuidado mientras

esté enchufado. Desenchufe el aparato de

la toma cuando no se esté utilizando, antes

de realizar trabajos de mantenimiento

y antes de guardarlo. Estas medidas

preventivas de seguridad reducen el riesgo

de arranque accidental de la herramienta.

• Las personas, niños y animales deberán

estar a 50’ (15 m) del aparato como

mínimo.

• Sólo para uso doméstico.

• Utilice solo baterías Snapper (Model

SBA260V, SBA2650V, and SBA460V)

• No utilice este aparato si está cansado o si

se encuentra bajo la inuencia de drogas,

alcohol o medicamentos.

• No trabaje con poca luz.

• Mantenga todas las partes de su cuerpo

lejos de cualquier parte móvil y todas las

supercies calientes de la unidad.

• No coloque ningún objeto en las aberturas.

No utilice con cualquier abertura

bloqueada. Mantenga las aberturas libres

de polvo, pelusas, pelo y cualquier cosa

que pueda reducir el ujo de aire.

• Compruebe el área de trabajo antes de

cada uso. Retire todos los objetos como

rocas, cristales rotos, clavos, cables o

cuerdas que puedan salir despedidos o

quedar enganchados en la máquina.

• Utilice sólo piezas y accesorios de

recambio del mismo fabricante. El uso de

otras piezas puede ocasionar riesgos o

daños en el producto.

PARA EL APARATO QUE FUNCIONA CON

• Evite la puesta en marcha accidental

de la herramienta. Asegúrese de que el

interruptor está en posición OFF antes

de conectar la herramienta a una batería,

y levantar o transportar el aparato. El

transporte del aparato con el dedo sobre

el interruptor o la conexión del aparato

con el interruptor en ON puede causar

accidentes.

• Desconecte la batería de la herramienta

de alimentación antes de hacer cualquier

ajuste, sustitución de accesorios, o

almacenar el aparato. Estas medidas

preventivas de seguridad reducen el riesgo

de arranque accidental del aparato.

• Recargue la unidad solamente con el

cargador especicado por el fabricante.

Podría haber un riesgo de incendio cuando

se utilice un cargador con una batería para

la que no está diseñado.

• Utilice el aparato solo con baterías

especícamente diseñadas para éste.

Utilizar cualquier otro tipo de baterías

puede causar lesiones o un riesgo de

incendio.

• Cuando la batería no está en uso,

manténgala alejada de otros objetos

metálicos como clips, monedas, llaves,

clavos, tornillos u otros objetos metálicos

pequeños que puedan crear una conexión

desde una terminal a otra. Si se produjese

un cortocircuito en los terminales de la

batería, éste podría causar quemaduras o

un incendio.

• En condiciones abusivas, podría salir

expulsado líquido de la batería, por lo

que debería evitar el contacto con éste.

Si se produce un contacto accidental,

enjuáguese las manos con agua. Si el

líquido entra en contacto con los ojos,

acuda inmediatamente al médico. Si el

líquido es expulsado de la batería podría

causar irritación o quemaduras.

• No utilice una batería o apartado dañado

o modicado. Las baterías dañadas o

modicadas pueden comportarse de modo

imprevisto que puede causar incendio,

explosión o riesgo de lesión.

• No exponga ni las baterías ni el aparato

al fuego ni a altas temperaturas. La

exposición a temperaturas superiores a

212°C puede provocar una explosión.

• Su producto debería ser reparado por

personas cualicadas, que deberían utilizar

únicamente piezas de repuesto idénticas.

Esto garantizará la seguridad a la hora de

utilizar el producto.

GUARDE ESTAS INSTRUCCIONES

REGLAS GENERALES DE SEGURIDAD

Not for Reproduction

REGLAS GENERALES DE SEGURIDAD

SERVICIO

Las reparaciones deben quedar en manos de

un técnico cualicado, utilizando únicamente

piezas de recambio originales. De este modo

podrá utilizar su herramienta eléctrica sin

peligro. El servicio o mantenimiento realizado

por personal no cualicado puede resultar en

un riesgo de lesión. Llame al 1-800-317-7833

para recibir asistencia.

SEGURIDAD DE NIÑOS

Si el operador no se percata de la presencia

de niños, se pueden generar accidentes

trágicos.

• Mantenga a los niños alejados del área

de trabajo y bajo el cuidado atento de

un adulto responsable.

• No deje que niños menores de 14 años

operen este recortador. Los niños de 14

años o más deben leer y comprender

las instrucciones de funcionamiento y

las reglas de seguridad de este manual

y uno de sus padres les debe capacitar

y supervisar.

• Manténgase alerta, y apague el

recortador si un niño o cualquier otra

persona ingresa al área de trabajo.

• Tenga extremo cuidado al acercarse a

esquinas ciegas, entradas, arbustos,

árboles u otros objetos que le pudieran

obstruir la visión de niños, los cuales

pudieran correr hacia el área de trabajo

del recortador.

ADVERTENCIA:

(PROPOSICIÓN 65)

El polvo creado por la arena a chorro, el

aserrado, esmerilado, taladrado y otras

actividades de la construcción podría

contener productos químicos que se sabe

provocan cáncer, defectos de nacimiento

y otras lesiones reproductivas. Algunos

ejemplos de estos productos químicos son:

• Plomo en pintura a base de plomo

• Sílice cristalino en ladrillos, cemento y

otros productos de mampostería, y

• Arsénico y cromo de madera con

tratamiento químico.

Su riesgo de exposición a estos productos

químicos depende de la frecuencia en que

efectúe este tipo de trabajo. Para reducir

su exposición a estos productos químicos,

trabaje en áreas bien ventiladas y use equipo

de seguridad aprobado, tal como máscaras

contra el polvo especialmente diseñadas para

ltrar partículas microscópicas.

GUARDE ESTAS INSTRUCCIONES

Not for Reproduction

Page is loading ...

Simplicity SB60V BLOWER, 60V User manual

Brand: Simplicity

Model: SB60V BLOWER, 60V

Category: Power tools

Type: User manual

This manual is also suitable for

SB60V

Download PDF

report

in other languages

español: Simplicity SB60V BLOWER, 60V Manual de usuario

Simplicity SB60V BLOWER, 60V User manual

This manual is also suitable for

Simplicity SB60V BLOWER, 60V User manual

in other languages

Related papers

Other documents