Haier H40K1 Owner's manual

Brand: Haier

Model: H40K1

Category: LCD TVs

Type: Owner's manual

This manual is also suitable for

Please READ this manual carefully before

operating your TV, and retain it for future

reference.

TFT-LCD TV

OWNER S MANUAL'

L40K1

Warning

RISK ELECTRIC SHOCK

DO NOT OPEN

CAUTION

CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK,

DO NOT REMOVE COVER (OR BACK).

NO USER SERVICEABLE PARTS INSIDE.

REFER SERVICING TO QUALIFIED SERVICE

PERSONNEL.

The lightning flash with arrowhead symbol, within an

equilateral triangle is intended to alert the user to the

presence of uninsulated dangerous voltage within the

product’s enclosure that may be of sufficient magnitude

to constitute a risk of electric shock.

The exclamation point within an equilateral triangle is

intended to alert the user to the presence of important

operating and maintenance (servicing) instructions in

the literature accompanying the appliance.

WARNING: TO PREVENT FIRE OR SHOCK HAZARD, DO NOT EXPOSE THIS APPLIANCE TO

RAIN OR MOISTURE.

CAUTION: TO PREVENT ELECTRIC SHOCK DO NOT USE THIS POLARIZED PLUG WITH AN

EXTENSION CORD, RECEPTACLE OR OTHER OUTLET UNLESS THE BLADES

CAN BE FULLY INSERTED TO PREVENT BLADE EXPOSURE.

CAUTION: These servicing instructions are for use by qualified service personnel only. To reduce the

risk of electric shock, do not perform any servicing other than that contained in the operating instructions

unless you are qualified to do so.

Important Safety Instructions

1) Read these instructions.

2) Keep these instructions.

3) Heed all warnings.

4) Follow all instructions.

5) Do not use this apparatus near water.

6) Clean only with dry cloth.

7) Do not block any ventilation openings. Install in accordance with the manufacturer's instructions.

8) Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including

amplifiers) that produce heat.

9) Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two blades with

one wider than the other. A grounding type plug has two blades and a third grounding prong. The wide blade or the

third prong are provided for your safety. If the provided plug does not fit into your outlet, consult an electrician for

replacement of the obsolete outlet.

10) Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles, and the

point where they exit from the apparatus.

11) Only use attachments/accessories specified by the manufacturer.

12) Use only with the cart, stand, tripod, bracket, or table specified by the manufacturer,

or sold with the apparatus. When a cart is used, use caution when moving the cart/

Apparatus combination to avoid injury from tip-over.

13) Unplug this apparatus during lightning storms or when unused for long periods of time.

14) Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been damaged

in any way, such as power-supply cord or plug is damaged, liquid has been spilled or objects have fallen into the

apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped.

15)The apparatus shall not be exposed to dripping or splashing and that no objects filled with liquids, such as vases,

shall be placed on the apparatus.

16)The mains plug or appliance inlet is used as the disconnect device, remain it readily operable during the

apparatus normal use.

Class I apparatus shall be connected to a mains socket outlet with a protective earthing connection.

Introduction

CONTENT

Introduction

Front panel controls

This is a simplified representation of front panel. Here shown may be somewhat different from your TV.

1.MENU: Menu display.

2.INPUT: Press to show the input source mode. In the MENU/INPUT screen, these buttons serve as OK buttons.

3.VOL -/+: Press to adjust the volume .In the MENU screen, these buttons serve as left/right buttons.

4.CH -/+ : Press to scan through channels. To scan quickly through channels, press and hold down either +/- . In the

MENU screen, these buttons serve as up/down buttons.

5.POWER: Press to turn on and off the TV.

6.HDMI IN:

Connect a signal to HDMI.

Headphone jack : Headphone audio output terminal.

8. AV2 VIDEO IN:

Connects the video signal from a video device.

9 .

AV2 AUDIO IN: connect to hear stereo sound from an external device.

10. USB:

from an external device

1 Digital Audio Output: Connect digital audio to various types of equipment.

NOTE: In standby mode, these ports will not work.

2 Antenna Input: Connect cable or antenna signals to the TV, either directly or through your cable box.

3 HDMI: Connect a signal to HDMI.

4 PC VIDEO In: Connect the audio out from the external device, used while linking PC audio frequency output terminals.

5 VIDEO In: Connects the video signal from a video device.

6 DVD/DTV In(Component ): Connect a component video device to these jacks.

7 AUDIO In: Connect to hear stereo sound from an external device.

8 S-VIDEO In: Connect S-Video out from an S-VIDEO device to the S-VIDEO input.

9 COMPONENT AUDIO In: Connect to hear stereo sound from an external device.

10 AUDIO In: Connect to hear stereo sound from an external device.

11 PC Audio In: Connect an audio cable for a computer to this jack.

12 AUDIO Out: Connect to the left and right audio input jacks of your audio or video equipment.

Back panel controls

Introduction

The remote control cannot be operated unless the batteries are properly loaded.

When using the remote control, aim it at the remote control sensor on the TV.

Function introduction

Remote Control

1.Press to turn on and off the TV

2.Press repeatedly to cycle through the available

picture modes

3.Press to change the aspect ratio

4.Select a closed caption option

5.Show the input source

6.Press to open the on-screen menu

7.Volume/Channel Selection

8.Exit On Screen Display

10.Press to display the TV status information on the top

of the TV screen

11.Shows program schedule in TV

12.Press to cycle through different sound settings

13.Press to display the sleep timer option

14.Select MONO, STEREO, SAP in NTSC system

15.Press to change a channel

16.Press to select digital channels. For example, to

enter “54-3”, press “54”, “- ” and “3”.

17.Switches the TV sound on or off

18.Accesses the highlighted item in the on-screen menu

19.Open the channel list in TV

20.Open the favorite channel list in TV

no available

ANT

Installation

Generally speaking, to enjoy a clearer picture, we recommend that you use a CATV system or an

outdoor antenna .

Over-the-air TV reception quality will depend on your antenna type, antenna

location and antenna positioning

External Equipment Connections

Antenna Connection

Multi-family Dwellings/Apartments

(Connect to wall antenna socket)

Wall Antenna

Socket

Single-family Dwellings /Houses

(Connect to wall jack for outdoor antenna)

Outdoor

Antenna

VHF Antenna

UHF Antenna

Turn clockwise to tighten

RF Coaxial Wire (75 ohm)

Bronze Wire

Be careful not to bend the bronze wire

when connecting the antenna.

Bronze Wire

To improve the picture quality in a poor signal area,

please purchase a signal amplifier and install properly.

If the antenna needs to be split for two TV`s, install

a 2-Way Signal Splitter in the connections.

To install the antenna properly please contact a

professional in your area.

Accessories

Remote control

Owner`s manual

Alkaline battery(AAA) 2

Please READ this manual carefully before

operating your TV, and retain it for future

reference.

TFT-LCD TV

OWNER S MANUAL'

Connection Instructions

VCR connection

NOTE: All cables shown are not included with the TV.

There are several ways to connect your television, depending on the components you want to connect

and the quality of the signal you want to achieve. The following are examples of some different ways

to connect your TV with different input sources.

Choose Your Connection

To avoid picture noise (interference), leave an adequate distance between the VCR and TV.

Connection Option 1

Set VCR output switch to channel 3 or 4 and

then tune the TV to the same channel number.

Connection Option 2

1. Connect the audio and video cables from the

VCR's output jacks to the TV input jacks, as

shown in the figure.

When connecting the TV to VCR, match the

jack colors (Video = yellow, Audio Left = white,

and Audio Right = red).

If you connect an S-VIDEO output from VCR to

the S-VIDEO input, the picture quality is

improved; compared to connecting a regular

VCR to the Video input.

2. Insert a video tape into the VCR and press

PLAY on the VCR. (Refer to the VCR owner`s

manual.)

3. Select the input source with using the

INPUT button on the remote control, and

then press CH+/- button to select the source,

press the OK button to confirm.

Installation

Connection Instructions

Installation

How to connect

1. Connect the DVD video outputs (COMPONENT) to

the Y Pb Pr jacks on the TV and connect the DVD audio

outputs to the Y Pb Pr Audio IN jacks on the TV, as

shown in the figure.

2. If your DVD only has an S-VIDEO output jack,

connect this to the S-VIDEO input on the TV. as shown

in the figure.

Note

If your DVD player does not have component video

output, use S-Video.

How to use

1. Turn on the DVD player, insert a DVD.

2. Use the INPUT button on the remote control to select

Y Pb Pr mode.

3. Press Play button on external equipment for program

play.

4. Refer to the DVD player's manual for operating

instructions.

How to connect

Connect the audio and video cables from the external

equipment's output jacks to the TV input jacks, as shown

in the figure. When connecting the TV to external equipment,

match the jack colors (Video = yellow, Audio Left = white,

and Audio Right = red).

How to use

1. Select the input source with using INPUT button on

the remote control.

2. Press CH+/- button to select the desired source.

3. Press OK button to confirm.

4. Operate the corresponding external equipment.

Video Game Set

Camcorder

Component Input ports

To get better picture quality, connect a DVD player to the

component input ports as shown below.

Component ports

on the TV

Video output ports

on DVD player

Y Pb Pr

Y B-Y R-Y

Y Cb Cr

Y P P

External A/V Source Setup

DVD connection

DVD

Connection Instructions

Installation

Digital Set-top Box

This TV can receive Digital Over-the-air/Cable signals without an external digital set-top box. However, if you do

receive Digital signals from a digital set-top box or other digital external device, refer to the figure as shown below.

This TV supports HDCP (High-bandwidth Digital Contents Protection) protocol for Digital Contents (480i,480p,720p,

1080i).

How to connect

Use the TV`s COMPONENT , VGA or HDMI

jack for video connections, depending on

your set-top box connector. Then, make

the corresponding audio connections.

How to use

1. Turn on the digital set-top box. (Refer to the

owner`s manual for the digital set-top box.)

2. Use INPUT on the remote control to select

COMPONENT , VGA or HDMIsource.

Send the TV`s audio to external audio equipment (stereo

system) via the Digital Audio Output (Optical) port.

How to connect

1. Connect one end of an optical cable to the TV Digital

Audio(Optical) Output port.

2. Connect the other end of the optical cable to the digital

audio (optical)input on the audio equipment.

See the external audio equipment instruction manual for

operation.

Note

When connecting with external audio equipments, such

as amplifers or speakers, please turn the TV speakers off.

Digital Audio Output

Caution: Do not look into the optical output port.

Looking at the laser beam may damage

your vision.

DTV connection

Signal

480i

480p

720p

1080i

COMPONENT

HDMI

Yes

HDMI

Connection Instructions

Installation

How to connect

1. To get the best picture quality, adjust the PC graphics card to 1024

2. Use the TV`s VGA or DVI (Digital Visual Interface)Audio IN port for video connections, depending on your

VGA connector.

If the graphic card on the PC does not output analog and digital RGB simultaneously, connect only one of

either VGA r HDMI/DVI IN to display the PC on the TV.

If the graphic card on the PC does output analog and digital RGB simultaneously, set the TV to eithe VGA

DVI; (the other mode is set to Plug and Play automatically by the TV.)

3. Then, make the corresponding audio connection. If using a sound card, adjust the PC sound as required.

How to use

1. Turn on the PC and the TV.

2. Turn on the display by pressing the POWER button on the TV's remote control.

3. Use INPUT on the remote control to select PC or HDMI source.

4. Check the image on your TV. There may be noise associated with the resolution, vertical pattern, contrast or

brightness in PC mode. If noise is present, change the PC mode to another resolution, change the refresh rate to

another rate or adjust the brightness and contrast on the menu until the picture is clear. If the refresh rate of the

PC graphic card can not be changed, change the PC graphic card or consult the manufacturer of the PC graphic

card.

Note

1.Use a HDMI to DVI cable.

2.Avoid keeping a fixed image on the TV's screen for a long period of time. The fixed image may become

permanently imprinted on the screen.

3. The synchronization input form for Horizontal and Vertical frequencies is separate.

x768 .

IN o

r or

HDMI/

Resolution

Frame

frequency

(Hz)

VGA

SVGA

XGA

60Hz

800x600

1024x768

60Hz

Mode

Resolution

75Hz

VGA connection

VIDEO

OPTICAL

COMPONENT IN

AV IN

Pb/Cb

Pr/Cr

SVIDEO

PC AUDIO

AUDIO

L R

AUDIO

OUT

AUDIO

AUDIO OUT

PC IN

HDMI/DVI IN

ANT IN

Connection Instructions

640x480

1280x1024

1280x768

1920x1080

When the source device(DVD player or Set Top Box) supports HDMI

How To Connect

1. Connect the source device to HDMI port of this TV with an HDMI cable(not supplied with this product).

2. No separated audio connection is necessary.

How To Use

If the source device supports Auto HDMI function, the output resolution of the source device will be automatically

set to 1280x720p.

If the source device does not support Auto HDMI, you need to set the output resolution appropriately.

To get the best picture quality, adjust the output resolution of the source device to 1280x720p.

Select HDMI input source in input source option of Select Main source menu.

Installation

HDMI Input

Connection Instructions

Removing the table stand and installing a

wall mount bracket

HDMI Cable

(not supplied with the product)

Cable sample

1. Remove 4X M4 screws securing the

stand to the TV, then remove the stand.

2. Use 4X M6 screws to secure the wall

bracket (not supplied) to the back of your TV.

Installation

Power source

TO USE AC POWER SOURCE

Use the AC polarized line cord provided for

operation on AC. Insert the AC cord plug into

a standard polarized AC outlet.

Note

Never connect the AC line cord plug to other

than the specified voltage. Use the attached

power cord only.

If the polarized AC cord does not fit into a non-

polarized AC outlet, do not attempt to file or cut

the blade. It is the user`s responsibility to have

an electrician replace the obsolete outlet.

If you cause a static discharge when touching

the unit and the unit fails to function, simply

unplug the unit from the AC outlet and plug it back

in. The unit should return to normal operation.

Polarized AC Cord Plug

AC Outlet

Wider Hole

and Blade

You can connect a set of headphones to your set if you wish to watch a

TV programme without disturbing the other people in the room.

Connecting Headphones

Note

Prolonged use of headphones at a high volume

may damage your hearing.

You will not receive sound from the speakers

when you connect headphones to the system.

Plug a set of headphones into the 3.5mm

mini-jack socket on the side panel of the set.

Connection Instructions

Operation

In the manual, the OSD (on screen display) may be different from your TV`s, because it is just an example to help

you with the TV operation.

There are several options you might need to set up in order for your TV to work properly. Read the instructions that

follow.

1. Choose the TV source and then press MENU button.

2. Press VOL+/- to select SETTINGS menu.

3. Press CH-/OK, then press CH+/- to select the

4. Press VOL+/OK, the opens.

5. Press CH+/- to select language you want.

You can select

Settings

Menu Settings

Korea English

Basic Operating Instructions

MOVE

SELECT PREVIOUS EXIT

EXIT

PICTURE

AUDIO

CHANNELS

SETTINGS

Settings

Closed Caption

Time

Menu Settings

Input Labels

Computer Settings

Component Settings

VOL

CH+

CH-

Adjust settings to affect picture quality

Turning on your TV for the first time

To turn on and configure your TV:

1 Make sure that you have inserted the batteries in the remote control, connected the antenna to the TV, and

connected the AC power.

2 Press POWER , then wait several seconds. The power indicator LED turns blue and the TV turns on.

Note

If the TV in power on , the screen show information according the type of input signal . the information will disappear.

If there is no signal , NO SIGNAL will display on the screen.

3 Select the signal source for your TV change the picture source so you can watch your TV, cable TV, VCR,

DVD, or any other devices that are connected to your TV.

1. Press INPUT to open the signal source menu and then press CH+/- button to select the source

2. Press VOL+/OK button to confirm .

4 Select the TV signal source for your TV and auto scan for channels

TV, Composite 1,

Composite 2, S-Video1, Component1, Component2,VGA/PC, HDMI-1, HDMI-2 or HDMI-3

MOVE

SELECT PREVIOUS EXIT

EXIT

PICTURE

AUDIO

CHANNELS

SETTINGS

Channels

Auto Channels Search

Add/Skip Channels

Favorites

Channel Labels

Channel Strength

Auto Zoom

VOL

CH+

CH-

Adjust settings to affect picture quality

1. Press MENU ,then press VOL+/- to select CHANNELS menu.

2. Press CH-/OK, the CHANNELS menu opens.

3. Press CH+/- to select the Auto Channels Search . Press

VOL+/OK the Auto Channels Search menu opens.

4. Press CH+/- to select Antenna or Cable, then press OK.

A checkmark appears in the circle next to your choice.

Press CH+/- to select START, then press VOL+/OK. The TV

automatically scans and memorizes all the active, available

channels in your area.

5 Set the volume of your TV by pressing VOL+ or VOL-.

6 Choose the Menu Language

7 Select the channel you want by pressing CH+/CH- to go to the next or previous channel, or directly by

pressing the number buttons.

Switching the TV On or Off

1 First, connect power cord correctly.

2 Press power button. Your TV turns on.

3 Press again to turn off your TV. When you turn off your TV, it goes into standby mode.

Warning: When your TV is in standby mode, it is still receiving power. To completely disconnect power, unplug the

power cord.

Note: If your TV does not receive an input signal for several minutes, it automatically goes into standby mode.

Mute

1.Press MUTE button to mute the sound temporarily. A mute icon appears on the screen.

2.Press MUTE button or VOL+ again to restore the sound.

The mute icon disappears.

Sleep button

Press SLEEP button to set the time : Off-5 min-10 min-15 min-30 min-45min-60 min-90 min-120 min-180 min-240min.

This feature allows you to turn off the television after a pre-selected number of minutes

- Button

Press to select additional channels (digital and analog) being broadcast by the same station. For example, to select

digital channel “11-1”, press “11”, then press “ - ” and “1”.

CH.LIST button

Press to display the program list. Press CH+/- to select the item and OK button to select the channel you desired.

FAVORITE button

Adding favorite channels

Press CH.LIST. The channel list opens. Press CH+/- to select a channel.

Press FAVORITE to add the channel to the favorites channel list.

To remove a favorite channel, open the channel list, select the channel you want to remove, then press FAVORITE.

Tuning to a favorite channel

Press FAVORITE The favorite channel list opens.

Press CH+/- to select the channel.

Your LCD TV automatically tunes to the channel you selected.

SAP Broadcasts Setup

This TV can receive MTS stereo programs and SAP (Secondary Audio Program) that accompanies the stereo

program; if the station transmits an additional sound signal as well as the original one.

When having selected SAP button on the remote control, this TV can only receive the signal when the TV station

transmits the proper signals.

Mono sound is automatically received if the broadcast is only in Mono; even though Stereo or SAP has been selected.

Select Mono if you want to listen to mono sound during stereo/SAP broadcasting.

Stereo or SAP can be received in a Analog channel.

1. Use MTS/SAP to select your desired MTS mode in a analog signal. Each time you press MTS/SAP, Mono,

Stereo or SAP appear. If other languages are available on the digital signal, select them with the MTS/SAP button.

2. Press EXIT to save and return to TV viewing.

ARC button

Selects the Aspect Ratio. You can select Zoom, Wide, Cinema or normal.

Zoom Choose Zoom when you want to view the picture without any alteration. However, the top and bottom

portions of the picture will be cropped.

Wide Choose wide when you want to adjust the picture horizontally, in a linear proportion to fill the entire screen.

Cinema For letterbox pictures, bars may appear on the top and bottom on some programs.

Normal Choose normal when you want to view the picture with original aspect ratio of the input signal.

CCD button

Basic Operating Instructions

Operation

Menu Operations

In this manual, the OSD (On Screen Display) may be differ from your TV.

These are examples to illustrate the TV's operation.

Press INPUT to select the input source. The menu for each source may be different .

1 Press MENU button to display the main menu, and VOL+/- to select the main menu .

2 Press CH-/OK button to enter the menu and CH+/- to go up and down to select the desired option .

3 Press VOL+/OK button to confirm and VOL+/- to make changes to the parameters.

4 Press EXIT/MENU button to exit the menu.

Picture Menu Options

The TV menu gives you an overview of the menus you can select.

Note

Depending on the input signal, one or more menu items may not

be selectable.

1 Press MENU ,then press VOL+/- to select PICTURE menu.

2 Press CH-/OK, then press to select an option.

3 Press , the m opens. then press to

adjust the option.

How to customize your own picture status

CH+/-

VOL+/OK enu VOL+/-

MOVE

SELECT PREVIOUS EXIT

EXIT

PICTURE

AUDIO

CHANNELS

SETTINGS

Picture

Standard

Mode

Brightness

Contrast

Color

Tint

Sharpness

VOL

CH+

CH-

Adjust settings to affect picture quality

Mode

Select the picture mode. You can select Vivid/Standard/Energy Savings/Theater/Sports/Custom.

You can also press PICTURE on the remote control to select the picture Mode.

Brightness

Contrast

Color

Tint

Sharpness

Reset to Default Re

Adjusts the brightness.

Adjusts the contrast.

Adjusts the color saturation.

Adjusts the image tint.

Adjusts the sharpness.

Lets you set the following:

• Aspect Ratio Select Normal, Zoom, Wide, Cinema, or Auto Zoom.

• Overscan Turn this On to adjust the picture’s reproduction rate when receiving DVI signals in VIDEO format.

Available when the signal uses EIA timing(480i/480p/720p/1080i/1080p).

• Color Temperature Select Warm (increased red), Normal, or Cool (increased blue).

• Backlight Adjusts the overall brilliance of the screen.

• Noise Reduction Selects the noise reduction mode to reduce picture noise (snow). Choose High, Middle,

Low, or Off.

• Advanced Contrast Turn this On to optimize the picture display for a more vivid image.

sets all picture settings to factory default.

Advanced Video

Menu Operations

Audio Menu Options

Equalizer Mode

Selects the sound mode. You can select :

Custom for a customized sound mode), Standard, Theater (for movies), Music (for musical programs),

News (for news programs).

You can also press AUDIO one or more times to cycle through the available sound modes.

Equalizer Setting

Lets you set custom audio settings when you select Custom

This will adjust the output of the right and left speakers to obtain the best stereo reproduction for your listening

position

Digital Audio/SPDIF

The TV can output Digital audio via the optical connector to an external amplifier or receiver.

Audio Language

Korea, English, Japan.

Balance

You can select RAW or PCM.

(DTV channels only)

Selects an alternate audio language, if available. You can select

Auto Volume Equalizes the overall volume levels for all channels.

Reset Audio Setting Resets all audio settings to factory default.

How to Customize your own audio status

1 Press MENU ,then press VOL+/- to select AUDIO menu.

2 Press CH-/OK ,then press CH+/- to select the desired items.

3 Press VOL+/OK, then press VOL+/- to adjust the setting.

4 When you are satisfied with your choice, press MENU

button to return to the previous menu or press EXIT button

to return to TV viewing.

Standard

RAW

Korea

Off

MOVE

SELECT PREVIOUS EXIT

EXIT

PICTURE

AUDIO

CHANNELS

SETTINGS

Audio

Equalizer Mode

Equalizer Setting

Balance

Digital Audio/SPDIF

Audio Language

Audio Volume

VOL

CH+

CH-

Adjust settings to affect picture quality

Operation

1 Press MENU ,then press VOL+/- to select CHANNELS menu.

2 Press CH-/OK, then press CH+/- one or more times to select

the Auto Channels Search .

3 Press VOL+/OK. The Auto Channels Search opens.

4 Press CH+/- to select Antenna or Cable, then press OK.

A checkmark appears in the circle next to your choice.

5 Press CH+/- to select START, then press VOL+/OK.

The TV automatically scans and memorizes all the active,

available channels in your area.

All available channels are automatically preset in order. After

the search is completed, the first channel number

displays on the screen. This search automatically adds only the

active channels in your area to the TV's memory.

It deletes any channels on which there is no broadcast or a poor

signal. The channels found are automatically saved.

6 To cancel searching, press EXIT button.

Adding or skipping channels

You can delete channels from the channel list so that your TV

skips the channels when you press CH+/-. You can still tune to

the hidden channel by using the number buttons.

the Add/Skip Channels option, your LCD TV scans for channels

starting at 21.

CHANNELS

Add/Skip Channels

VOL+/OK. T Add/Skip Channels menu opens

Notes:

1 Press MENU ,then press VOL+/- to select menu.

2 Press CH-/OK ,then press CH+/- one or more times to select

the .

3 Press he .

4 Press CH+/-or VOL+/- to highlight the channel you want to

skip (the default is to show the channel), then press

ENTER to remove the check mark from the channel.

Notes:

If the list has more than one page, press CH+/- to scroll through

the pages.

To add a channel that is being skipped, repeat Steps 1 to 4 and

press ENTER to return the checkmark to the channel.

5 To cancel searching, press EXIT button.

The Channel menu will be only operated in normal TV mode.

Menu Operations

Channels Menu Options

1 Press INPUT ,then press to select TV option.

2 Press OK, to select the TV signal source.

Automatically scanning for channels

Automatically finds all channels available through antenna or cable inputs, and stores them in memory on the All

Channel List.

CH+/-

VOL+/

To select the TV signal source:

MOVE

SELECT

EXIT

PICTURE

AUDIO

CHANNELS

SETTINGS

Channels

Channels Auto Channels Search

Channels

Add/Skip Channels

Auto Channels Search

Add/Skip Channels

Favorites

Channel Labels

Channel Strength

Auto Zoom

Choose your TV source

Antenna

Cable

Start

Auto Channels Search

Add/Skip Channels

Favorites

Channel Labels

Channel Strength

Auto Zoom

Ch 2.0

Ch 6.0

Ch 11.1 MBC DTV

Ch 14.1 ATSC-1

Ch 14.1 ATSC-3

VOL

CH+

CH-

VOL

CH+

CH-

VOL

CH+

CH-

VOL

CH+

CH-

Adjust settings to affect picture quality

Select Cable if cable is connected directly to the TV

Adjust settings to affect picture quality

Manually add and skip channels in your program list

Ch 5.1 KPIX-DT

Ch 10.1 WCAU-DT

Ch 13.1

Ch 14.2 ATSC-2

Ch 65.0

0 Analog Channels

Digital Channels0

Operation

Menu Operations

Channels Menu Options

Setting up a favorite channel list

You can create a favorite channel list so you can quickly browse

through your favorite channels by pressing FAVORITE, then

selecting a channel from the favorite channel list.

MOVE

SELECT

EXIT

PICTURE

AUDIO

CHANNELS

SETTINGS

Channels

Channels Favorites

Channels Channel Labels

Channels

Auto Channels Search

Add/Skip Channels

Favorites

Channel Labels

Channel Strength

Auto Zoom

Auto Channels Search

Add/Skip Channels

Favorites

Channel Labels

Channel Strength

Auto Zoom

VOL

CH+

CH-

VOL

CH+

CH-

VOL

CH+

CH-

VOL

CH+

CH-

Adjust settings to affect picture quality

Add channels to create a favorites list

Adjust settings to affect picture quality

1 Press MENU ,then press VOL+/- to select menu.

2 Press CH-/OK ,then press CH+/- one or more times to select

the Favorite.

3 Press he Favorite .

4 Press CH+/- to select the channel you want to add or remove,

then press OK to add or remove the channel from the list.

5 P close the menu.

6 To select a channel in your favorites list, press FAVORITE on

the remote control, press CH+/- to select the channel.

CHANNELS

VOL+/OK. T menu opens

ress EXIT .

1 Press MENU ,then press VOL+/- to select menu.

2 Press CH-/OK ,then press CH+/- one or more times to select

the .

3 Press he .

4 Press CH+/- to select the channel you want to label,

press VOL+/- to go to the channel label field.

5 Press CH+/- to select the number or symbol you want,

then press VOL+ to go to the next character. You can use as many

as ten characters to label a channel.

6 When you have finished entering a label, press OK to

confirm.

Notes:

To change a character, press VOL+/- to go to the character you

want to change, then press CH+/- to select a new character.

Repeat Steps 4 to 6 to label additional channels.

7 Press MENU to exit to the previous menu or EXIT to close the

menu.

CHANNELS

VOL+/OK. T menu opens

Channel Labels

Adding or changing a channel label

If a channel is not already labeled, you can label the channel to

make it easier to identify. You can also relabel a channel that is

already labeled.

Ch 2.0

Ch 6.0

Ch 11.1 MBC DTV

Ch 14.1 ATSC-1

Ch 14.1 ATSC-3

Ch 5.1 KPIX-DT

Ch 10.1 WCAU-DT

Ch 13.1

Ch 14.2 ATSC-2

Ch 65.0

2.0

Checking the DTV signal strength

You can check the DTV signal strength to determine if you need to

adjust your antenna or digital cable input. The signal strength, the

less likely you are to experience picture degradation.

1 Press MENU ,then press VOL+/- to select menu.

2 Press CH-/OK ,then press CH+/- one or more times to select

the .

3 Press he displaying the

signal strength of the channel.

4 P close the menu.

Turning on Auto Zoom

Auto Zoom automatically adjusts the aspect ratio of the picture, based

on TV size and TV program.

1 Press MENU ,then press VOL+/- to select menu.

2 Press CH-/OK ,then press CH+/- one or more times to select

the Auto Zoom.

3 Press he Auto Zoom . Press CH+/- to

select On.

4 P close the menu.

CHANNELS

VOL+/OK. T menu opens

CHANNELS

VOL+/OK. T menu opens

Channel Strength

ress EXIT

Operation

Menu Operations

Channels Menu Options

MOVE

SELECT PREVIOUS EXIT

EXIT

PICTURE

AUDIO

CHANNELS

SETTINGS

Channels

Auto Channels Search

Add/Skip Channels

Favorites

Channel Labels

Channel Strength

Auto Zoom

VOL

CH+

CH-

Adjust settings to affect picture quality

Operation

Menu Operations

Settings Menu Options

MOVE

SELECT

EXIT

PICTURE

AUDIO

CHANNELS

SETTINGS

Settings

Closed Caption

Settings Time

Closed Caption

Time

Menu Settings

Input Labels

Computer Settings

Component Settings

Caption mode CC Off

Analog Caption English

Digital Caption CC1

Digital CC Settings

Mode Manual

Clock 04:22 AM

Off Time 04:22 AM

On Time 04:22 AM

Sleep Timer Off

VOL

CH+

CH-

VOL

CH+

CH-

VOL

CH+

CH-

Adjust settings to affect picture quality

Set Closed Caption Mode

If Automatic, options are automatically set by TV source

Closed Caption

SETTINGS

Closed Caption

VOL+/OK. T Closed Caption menu opens

VOL+/OK

Caption m

SETTINGS

VOL+/OK. T menu opens

VOL+/OK

Lets you turn closed captioning on or off. Also lets you set

closed caption options.

1 Press MENU ,then press VOL+/- to select menu.

2 Press CH-/OK ,then press CH+/- one or more times to select

the .

3 Press he .

Press CH+/- to select the option, press to

open the sub-menu, then press CH+/- to set up. Options include:

ode Select CC On, CC Off, or CC On Mute.

Analog Caption For analog programming. Options

include:

• Cc1 Standard CC display.

• CC2 to Cc4 For other modes of video related broadcast

information.

• Text1 For a program guide or other information

displayed by broadcasters.

• Text2 to Text4 For additional modes of information

displayed by broadcasters.

• Off Turns analog captions off.

Digital Caption For digital programming. Select CS1,

CS2, CS3, CS4, CS5, CS6, or Off.

Digital CC Settings To change digital closed caption

settings. Options include:

• Style Select either Automatic or Custom. When you

select automatic, the others are disabled and cannot be

adjusted.

• Size To select the size of the caption displayed.

• Font

To select the font of the caption displayed.

• Text Color To select the text color or the opacity of the

text box of caption display. Select a color and one of the

opacity options.

• Text Opacity To specify the opacity for the text color.

• Background Color To select a background color.

• Background Opacity To select the opacity for the

background color.

• Edge Effect To select the edge effect.

• Edge Color To select the edge color.

4 Press MENU to return to the previous menu, or press EXIT to

close the menu.

You can also press CCD to turn closed captioning on or off.

Adjusting time settings

Lets you set the clock.

1 Press MENU ,then press VOL+/- to select menu.

2 Press CH-/OK ,then press CH+/- one or more times to select

the Time.

3 Press he Time .

Press CH+/- to select the option, press to

open the sub-menu, then press CH+ /-to select Date/Time, then

press . The Date/Time menu opens.

Page is loading ...

Haier H40K1 Owner's manual

Brand: Haier

Model: H40K1

Category: LCD TVs

Type: Owner's manual

This manual is also suitable for

Download PDF

report

Haier H40K1 Owner's manual

This manual is also suitable for

Haier H40K1 Owner's manual

Related papers

Other documents