WELDSKILL 130, 170 Addendum
2-4 Manual 0-5341_AA, March 5, 2014
2.10 Specifications
Description Weldskill 130 Weldskill 170
Power Source Part Number W1002800 W1002900
Cooling Fan Cooled Fan Cooled
Welder Type Inverter Power Source Inverter Power Source
Welding Power Source Mass 5.5kg 6.5kg
Dimensions H 280mm x W 120mm x D
220mm
H 330mm x W 130mm x D
230mm
Manufactured to Australian
Standard
AS60974.1-2006 AS60974.1-2006
Number of Phases Single Phase Single Phase
Nominal Supply Voltage 240V +/- 15% 240V +/- 15%
Nominal Supply Frequency 50Hz 50Hz
Welding Current Range 5-130 Amps 5-170 Amps
Factory Fitted Supply Plug Rating 10 Amps 15 Amps
Effective Input Current (I
1eff ) 10 Amps 15 Amps
Maximum Input Current (I
1max) 23 Amps 31 Amps
Minimum Single Phase Generator
Recommended (Refer Note 3)
5.6kW (7kVA at 0.8 PF) 7.2kW (9kVA at 0.8 PF)
Welding Output, 40ºC, 10 min.
(STICK- MMAW)
130A @ 20%, 25.2V
75A @ 60%, 23.1V
58A @ 100%, 22.3V
170A @ 25%, 26.8V
110A @ 60%, 24.0V
85A @ 100%, 23.2V
Welding Output, 40ºC, 10 min.
(TIG -GTAW)
130A @ 26%, 15.2V
85A @ 60%, 13.4V
66A @ 100%, 12.6V
170A @ 25%, 16.8V
110A @ 60%, 14.0V
85A @ 100%, 13.2V
Protection Class IP23S IP23S
NOTE 1
The Effective Input Current should be used for the determination of cable size & supply requirements.
NOTE 2
Motor start fuses or thermal circuit breakers are recommended for this application. Check local
requirements for your situation in this regard.
WELDSKILL 130, 170 (0-5048_AE) Addendum
Please replace pages 2-4 and 2-5 in the WELDSKILL 130, 170 operating manual (0-5048_AE) with these pages.
These revisions supersede any information in the printed operating manual, or printed on the WELDSKILL
130, 170.
Please keep and retain this information with the operating manual for future reference.
Manual 0-5341_AA, March 5, 2014 2-5
Addendum WELDSKILL 130, 170
NOTE 3
Minimum Generator Recommendation at the Maximum Output Duty Cycle.
Due to large variations in performance and specifications of different brands and types of genera
-
tors, CIGWELD cannot guarantee full welding output power or duty cycle on every brand or type
of generator.
Some small generators incorporate low cost circuit breakers on their outputs. These circuit break
-
ers usually will have a small reset button, and will trip much faster than a switchboard type circuit
breaker. This may result in not being able to achieve full output or duty cycle from the power source
/ generator combination. For this reason we recommend a generator that incorporates switchboard
type circuit breakers.
In some circumstances, long welds at high welding current may trip the circuit breaker on the
generator.
CIGWELD recommends that when selecting a generator, that the particular power source / generator
combination be adequately trialled to ensure the combination performs to the users expectations.
NOTE 4
CIGWELD reserves the right to change product performance and specifications without notice.
NOTE 5
Due to variations that can occur in manufactured products, claimed performance, voltages, ratings,
all capacities, measurements, dimensions and weights quoted are approximate only. Achievable
capacities and ratings in use and operation will depend upon correct installation, use, applications,
maintenance and service.
2.11 Options and Accessories
Description Part Number
TIG Torch Weldskill 130 Inverter W7003006
TIG Torch Weldskill 170 Inverter W7003021
TIG torch Accessory Kit BGSAK2
Flow Meter/Regulator 210254
-
1
-
2
ESAB 170 Troubleshooting instruction
- Type
- Troubleshooting instruction
- This manual is also suitable for
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Related papers
-
ESAB 130 170 WELDSKILL® Inverter Arc Welding Machines User manual
-
-
-
-
-
-
-
-
-
