Marantec EM 184 Owner's manual

Brand: Marantec

Model: EM 184

Type: Owner's manual

Expansion module EM 184

Draw-in protection MSBUS

Manual for installation and operation

2 Manual for installation and operation, Expansion module EM 184 GB (#116357 / 1700020543)

2. Table of contents

Caution!

Danger of personal injury!

The following safety advice must be

observed at all times so as to avoid

personal injury!

Attention!

Danger of material damage!

The following safety advice must be

observed at all times so as to avoid

material damage!

Advice / Tip

Check

Reference

Advice

1. Meaning of symbols . . . . . . . . . .2

2. Table of contents . . . . . . . . . . . .2

3. General safety advice . . . . . . . . .3

4. Product overview . . . . . . . . . . . .5

5. Installation . . . . . . . . . . . . . . . . .5

5.1 Install expansion module . . . . .5

5.2 Wiring of the expansion

module . . . . . . . . . . . . . . . . . .6

6. Initial operation . . . . . . . . . . . . .9

7. Programming . . . . . . . . . . . . . . .9

8. Appendix . . . . . . . . . . . . . . . . . .10

1. Meaning of symbols

Manual for installation and operation, Expansion module EM 184 GB (#116357 / 1700020543) 3

3. General safety advice

Target group

This operator system may only be installed, connected and put into operation by qualified and trained

professionals!

Qualified and trained specialist personnel are persons

- who have knowledge of the general and special safety regulations,

- who have knowledge of the relevant electro-technical regulations,

- with training in the use and maintenance of suitable safety equipment,

- who are sufficiently trained and supervised by qualified electricians,

- who are able to recognise the particular hazards involved when working with electricity,

- with knowledge regarding applications of the EN 12635 standard (installation and usage requirements).

Warranty

For an operations and safety warranty, the advice in this instruction manual has to be observed.

Disregarding these warnings may lead to personal injury or material damage. If this advice is disregarded,

the manufacturer will not be liable for damages that might occur.

To avoid installation errors and damage to the device, it is imperative that the installation instructions are

followed. The product may only be operated after reading these installation and operating instructions.

The installation and operating instructions are to be given to the door system user, who must keep them

safe. They contain important advice for operation, checks and maintenance.

This item is produced according to the directives and standards mentioned in the Manufacturer's

Declaration and in the Declaration of Conformity. The product has left the factory in perfect condition with

regard to safety.

Power-operated windows, doors and gates must be checked by an expert (and this must be documented)

before they are put into operation and thereafter as required, but at least once a year.

Correct use

The expansion module expands the Control vario control unit.

Beside the advice in these instructions, please observe the general safety and accident

prevention regulations! Our sales and supply terms and conditions are effective.

Please read carefully!

3. General safety advice

Installation tips

• Ensure that the devices to be connected (doors etc.) are in a mechanically faultless state.

• Before commencing cabling works it is very important to disconnect the system from the electricity supply.

Ensure that the electricity supply remains disconnected throughout the cabling works.

• Adhere to the local protection regulations.

• Lay the electricity supply cables and control cables; these MUST be laid separately.

The operating voltage is 24 V.

Information on cleaning the operator system

Never use water jets, high pressure cleaners, acids or bases for cleaning.

Please read carefully!

4 Manual for installation and operation, Expansion module EM 184 GB (#116357 / 1700020543)

Manual for installation and operation, Expansion module EM 184 GB (#116357 / 1700020543) 5

XW41A

XP16BXP16A

DIP

LED 4

LED 3

LED 2

LED 1

OFF

ES MODUL

XW41C

Supply package

Dimensions

1 Expansion module

2 System cable coded

3 MSBUS cable

4 / 1

XW41A

XP16BXP16A

DIP

LED 4

LED 3

LED 2

LED 1

OFF

ES MODUL

XW41C

4 / 2

126

XW41B

XW41A

XP16BXP16A

DIP

LED

LED 3

LED

LED 1

OFF

ES MODUL

5.1 Install expansion module

5. Installation

• Fit the expansion module (B) to the DIN rail (A).

5.1 / 1

4. Product overview

XW41B

XW41C

XW41A

XP16BXP16A

DIP

LED 4

LED 3

LED 2

LED 1

OFF

ES MODUL

5. Installation

6 Manual for installation and operation, Expansion module EM 184 GB (#116357 / 1700020543)

Label Type / function

Operating indicator

Light on . .......... In operation

B Draw-in protection XP16A

C Draw-in protection testing

D Draw-in protection XP16B

E Dip switch DIP 1

F Dip switch DIP 2

XP16A Draw-in protection I

XP16B Draw-in protection II

XW41A MSBUS connection

XW41B Connection of further module

XW41C Connection of further module

5.2 Wiring of the expansion

module

5.2.1 Overview of the module connections

5.2.1 / 1

XW41C XP16B

XP16A

XW41B

XW41A

DIP 1 Function

OFF Draw-in protection 12V

ON Draw-in protection 24V

DIP 2 Function

OFF Draw-in protection, OPENING

ON Draw-in protection, CLOSING

DIP switch (E) settings

DIP switch (F) settings

B, C, D:

Light flashes

.......... Cable break

Single flash (run light)

...scanning MSBUS

Manual for installation and operation, Expansion module EM 184 GB (#116357 / 1700020543) 7

XW41B

XW41C

- XP16A / XP16B

- BP30B

- BP30A

-X1

-W2

br br

gr gr

-W3

Connection for draw-in protection tested

Label Type / function

BP30A Draw-in protection, receiver RX

BP30B Draw-in protection, transmitter TX

X1 Terminal

5.2.2 / 2

M14E006

5. Installation

Attention!

To ensure correct operation, only use

the Marantec bus system (MS bus).

5.2.2 Connection of the modules

XW41C

XW41A

• Connect the MS bus control unit to the

connecting socket XW41A or XW41B.

• Connect further modules to socket XW41C as

required.

5.2.2 / 1

XW41B

Connection of the control unit and a further

module

DIP 1 Function

OFF Draw-in protection 12V

ON Draw-in protection 24V

DIP switch (E) settings

Attention!

Selecting the wrong voltage will

destroy the photocell.

8 Manual for installation and operation, Expansion module EM 184 GB (#116357 / 1700020543)

5. Installation

Connection for draw-in protection, dynamic

- XP16A / XP16B

wt br gr

- BP29B

- BP29A

-W1

5.2.2 / 3

M14E006

Connection for draw-in protection with relay

- XP16A

wt br

- BP31A

- BP31B

+24V

GND

COM

+24V

GND

5.2.2 / 4

M14E006

Label Type / function

BP29A Optosensor, receiver RX

BP29B Optosensor, transmitter TX

DIP 1 Function

OFF Draw-in protection 12V

DIP switch (E) settings

Label Type / function

BP31A Draw-in protection, receiver RX

BP31B Draw-in protection, transmitter TX

DIP 1 Function

ON Draw-in protection 24V

DIP switch (E) settings

Manual for installation and operation, Expansion module EM 184 GB (#116357 / 1700020543) 9

7. Programming

After connecting the control unit, the LED

displays (B, C, D) flashes slowly.

• The module will be recognised automatically by

the control during initial use.

The control unit requires approx. 30 seconds to

recognise any modules connected to it.

The module reset ends automatically

(run light display B, C, D).

XW41B

XW41C

XW41A

XP16BXP16A

DIP

LED 4

LED 3

LED 2

LED 1

OFF

ES MODUL

6 / 1

6. Initial operation

Advice:

The draw-in protection must be

connected up before initial use.

Possible draw-in protection:

- Three-wire draw-in protection,

- Four-wire draw-in protection with

testing, or

- Draw-in protection with relay

Reference:

For instructions on programming

expansion module EM 184, please

refer to the documentation provided

with the control units concerned.

10 Manual for installation and operation, Expansion module EM 184 GB (#116357 / 1700020543)

8. Appendix

Technical data

Operating

voltage

V 24 to 30

Max. draw-in

protection

current

mA 20

Protection

Marantec EM 184 Owner's manual

Marantec EM 184 Owner's manual

Marantec EM 184 Owner's manual

Related papers

Other documents