Ibiza Light & Sound SUPPORT DE LUMIERE AVEC 4 PROJECTEURS PAR 12 x 1W RGBW (DJLIGHT80LED) Owner's manual

Page is loading ...

2

©Copyright LOTRONIC 2016 DJLIGHT80LED

Unpacking Instructions

Immediately upon receiving a fixture, carefully unpack the carton, check the contents to ensure that all parts are

present and have been received in good condition. Notify the freight company immediately and retain packing

material for inspection if any parts appear to be damaged from shipping or the carton itself shows signs of

mishandling. Keep the carton and all packing materials. In the event that a fixture must be returned to the

factory, it is important that the fixture be returned in the original factory box and packing.

Safety Instructions

Please read these instructions carefully, they include important information about the installation, usage and

maintenance of this product.

• Please keep this User Guide for future reference. If you sell the unit to another user, be sure that he also

receives this instruction booklet.

• Always make sure that you are connecting to the proper voltage, and that the line voltage you are connecting

to is not higher than that stated on the decal or rear panel of the fixture.

• This product is intended for indoor use only!

• To prevent risk of fire or shock, do not expose fixture to rain or moisture. Make sure there are no flammable

materials close to the unit while operating.

• The unit must be installed in a location with adequate ventilation, at least 1m from adjacent surfaces. Be sure

that no ventilation slots are blocked.

• Always disconnect from power source before servicing or replacing fuse and be sure to replace with same fuse

size and type.

• Maximum ambient temperature (Ta) is 104° F (40°C). Do not operate the fixture at temperatures higher than

this.

• In the event of a serious operating problem, stop using the unit immediately. Never try to repair the unit by

yourself. Repairs carried out by unskilled people can lead to damage or malfunction. Please contact the nearest

authorized technical assistance center. Always use the same type of spare parts.

• Make sure the power cord is never crimped or damaged.

• Never disconnect the power cord by pulling or tugging on the cord.

• Avoid direct eye exposure to the light source while it is on.

• DISCONNECT DEVICE: Where the MAINS plug or an appliance coupler is used as the disconnect device, the

disconnect device shall remain readily operable.

• The light source contained in this luminaire shall only be replaced by the manufacturer or his service agent or a

similar qualified person.

Specifications

Voltage ................................................................................... 220-240V AC~ 50/60Hz

Consumption ....................................................................................................... 60W

LED lamp: ................................................................................... 12 x 1W (RGBW) x 4

DMX channels ........................................................................................................... 8

Control modes ..................................................... Auto, Master/Slave, DMX, Remote

Power cable ........................................................................................................... 4m

Packing Size...................................................................................... 89.5 x 19 x 39cm

GB

3

©Copyright LOTRONIC 2016 DJLIGHT80LED

Power supply, wire Connection

Use a dedicated plug to connect the LED light and power. Make sure the unit is connected to the appropriate

power supply.

Installation of the units

Before positioning the light, ensure the stability of the installation site. Drive the screw into the screw hole on

the stand. Make sure that the units can’t fall from the stand. The manufacturer cannot be held responsible for

damages due to bad installation of the units.

Warning

Carry the lights only by the handle.

Features

The control panel features 4 buttons and a 4-digit LED display.

Operation

1) When power is on, the digital LED display works with red dots.

When a DMX signal is present, the dot will be shiny.

2) DMX address code setting: Press “MENU” button. When the digital LED displays d001-d512, press “UP” or

“Down” to set the address code. The code ranges from 001-512.

3) IP code setting: Press “MENU”. When IP.01-IP.64 is displayed, press “UP” or “DOWN” to set the address code.

The code ranges from 001-512.

4) Internal program running:

There are 5 built-in programs. Press “MENU” to choose one of the built-in programs from A1-A5: A1 is static

color mode, A2 LED jump function, A3 LED rainbow function, A4 LED sound active function, and A5 LED

strobe function, A6 is Auto Run and A7 scrolling effect.

Button Specifications:

Connection of Signal Cable

You can use the 3-pin XLR cable to connect the OUT socket of the first light and the IN socket of the following

light. Connect all the lights as below:

A1

Solid Mode

←UP/DOWN→ 1-19

A2.

Jump Mode

←UP/DOWN→ 1-19

A3.

Rainbow mode

←UP/DOWN→ 1-19

A4.

Sound active mode

←UP/DOWN→ 1-19

A5.

Strobe Mode

←UP/DOWN→ 1-19

R.

Solid Red Color intensity

←UP/DOWN→ 0-255

G.

Solid Green Color intensity

←UP/DOWN→ 0-255

B.

Solid Blue Color intensity

←UP/DOWN→ 0-255

U.

Red+White Color Wash

←UP/DOWN→ 0-255

D.

DMX Mode

d.512

IP.

IP Mode

IP.64

4

©Copyright LOTRONIC 2016 DJLIGHT80LED

A DMX signal terminator is recommended on the last unit of the chain. DMX terminator is a XLR connector with

a 120Ω resistor between the pin 2 and pin 3 of the XLR connector

Remote Control:

A1: Effect 1 All bright

A2: Effect 2 Jump change

A3: Effect 3 Gradual change

A4: Sound activated

A5: Strobe

Color: Color adjustment

Speed: Speed adjustment

DMX: Selection of DMX channel

IP: Running effect

DMX Channels:

Channel

Value

Description

Reminder

CH 1

0-10

No function

Macro function

11-50

Macro A1

51-100

Macro A2

101-150

Macro A3

151-200

Macro A4

201-255

Macro A5

210-255

Red+Green+Blue

CH2

0-255

Macro color

CH3

0-255

Speed adjustable

CH4

0-255

Master dimming

CH5

0-255

Red dimming

CH6

0-255

Green dimming

CH7

0-255

Blue dimming

CH8

0-255

White dimming

Fixture Cleaning

The cleaning of internal and external optical lenses and/or mirrors must be carried out periodically to optimize

light output. Cleaning frequency depends on the environment in which the fixture operates: damp, smoky or

particularly dirty surrounding can cause greater accumulation of dirt on the unit’s optics.

• Clean with soft cloth using normal glass cleaning fluid.

• Always dry the parts carefully.

5

• Clean the external optics at least every 20 days. Clean the internal optics at least every 30/60 days.

VII. Trouble-shooting

Problem

Solution

No display when power is on

1. Check if the power is correctly connected.

2. Check the outlet is powered

Light is out of control

1. Check if the DMX address code is correctly set.

2. Check if the DMX cable is correctly connected.

The light is off after working for a while

1. Check if the sensor is soldered on the LED PCB

2. Check if the temperature is too high or not.

3. Check if Power supply is damaged.

The beam is dark

1. Check if the temperature is too high and cause a fast fade.

2. Check if there are too much dust on the surface of light.

This marking indicates that this product should not be disposed with other household wastes

throughout the EU. To prevent possible harm to the environment or human health from uncontrolled

waste disposal, recycle it responsibly to promote the sustainable reuse of material resources. To

return your used device, please use the return and collection systems or contact the retailer where the

product was purchased. They can take this product for environmental safe recycling.

Déballage

Dès réception de l’appareil, ouvrez le carton et vérifiez que le contenu est complet et en bon état. Sinon,

prévenez immédiatement le transporteur et conservez l’emballage s’il montre des signes de mauvais

traitements. Conservez le carton et tous les matériaux d’emballage afin de pouvoir transporter l’appareil en

toute sécurité.

Consignes de sécurité

Lisez attentivement ce manuel qui contient des informations importantes sur l’installation, l’utilisation et

l’entretien de cet appareil.

• Conservez le manuel pour référence ultérieure. Si l’appareil change un jour de propriétaire, assurez-vous que

le nouvel utilisateur est en possession du manuel.

• Assurez-vous que la tension secteur convient à cet appareil et qu’elle ne dépasse pas la tension d’alimentation

indiqué sur la plaque signalétique de l’appareil.

• Uniquement pour utilisation à l’intérieur!

• Afin d’éviter tout risque d’incendie ou de choc électrique, ne pas exposer cet appareil à la pluie ou à

l’humidité. Assurez-vous qu’aucun objet inflammable ne se trouve à proximité de l’appareil pendant son

fonctionnement.

• Installez l’appareil à un endroit bien ventilé à une distance minimum de 1m de toute surface. Assurez-vous que

les fentes de ventilation ne sont pas bloquées.

• Débranchez l’appareil du secteur avant toute manipulation ou entretien. Lorsque vous remplacez le fusible,

utilisez uniquement un fusible qui présente exactement les mêmes caractéristiques que l’ancien.

• La température ambiante ne doit pas dépasser 40°C. Ne pas faire fonctionner l’appareil à des températures

supérieures.

F

Page is loading ...

Ibiza Light & Sound SUPPORT DE LUMIERE AVEC 4 PROJECTEURS PAR 12 x 1W RGBW (DJLIGHT80LED) Owner's manual

This manual is also suitable for

Ibiza Light & Sound SUPPORT DE LUMIERE AVEC 4 PROJECTEURS PAR 12 x 1W RGBW (DJLIGHT80LED) Owner's manual

in other languages

Related papers

Other documents