Sony 46HX803 User manual

Category
LED TVs
Type
User manual

This manual is also suitable for

4-180-175-11(1)
LCD
Digital Colour TV
Operating Instructions
Setting Up
Watching TV
Additional Information
KDL-52HX903 / 46HX903 / 46HX803 / 40HX803
2
GB
NOTICE FOR
CUSTOMERS IN
THE UNITED
KINGDOM
A moulded plug complying with BS1363 is
fitted to this equipment for your safety and
convenience.
Should the fuse in the plug supplied need to
be replaced with the same rating of fuse
approved by ASTA or BSI to BS 1362 (i.e.,
marked with or ) must be used.
When an alternative type of plug is used it
should be fitted with the same rating of
fuse, otherwise the circuit should be
protected by a 10 AMP FUSE at the
distribution board.
If the plug supplied with this equipment has
a detachable fuse cover, be sure to attach
the fuse cover after you change the fuse.
Never use the plug without the fuse cover.
If you should lose the fuse cover, please
contact your nearest Sony service station.
How to replace the fuse
Open the fuse compartment with a blade
screwdriver, and replace the fuse.
Please refer to the illustration that actually
equipped with the product.
Introduction
Thank you for choosing this Sony product.
Before operating the TV, please read this
manual thoroughly and retain it for future
reference.
Notes on Digital TV
function
Any functions related to Digital TV
( ) will only work in countries or
areas where DVB-T (MPEG-2 and
H.264/MPEG-4 AVC) digital terrestrial
signals are broadcast or where you have
access to a compatible DVB-C (MPEG-
2 and H.264/MPEG-4 AVC) cable
service. Please confirm with your local
dealer if you can receive a DVB-T signal
where you live or ask your cable
provider if their DVB-C cable service is
suitable for integrated operation with
this TV.
Your cable provider may charge a fee for
their services, or require you to agree to
its terms and conditions of business.
This TV set complies with DVB-T and
DVB-C specifications, but compatibility
with future DVB-T digital terrestrial and
DVB-C digital cable broadcasts are not
guaranteed.
Some Digital TV functions may not be
available in some countries/areas and
DVB-C cable may not operate correctly
with some providers.
For a list of compatible cable providers,
refer to the support web site:
http://support.sony-europe.com/TV/
DVBC/
~
Instructions about “Installing Wall
Mount Bracket” are included within this
TV’s instructions manual.
The illustrations of the remote used in
this manual are of the RM-ED034 unless
otherwise stated.
The illustrations used in this manual may
differ depending on your TV model.
Trademark information
is a registered trademark of the DVB
Project.
HDMI, the HDMI Logo, and High-
Definition Multimedia Interface are
trademarks or registered trademarks of
HDMI Licensing LLC in the United States
and other countries.
DLNA®, the DLNA Logo and DLNA
CERTIFIED® are trademarks, service
marks, or certification marks of the Digital
Living Network Alliance.
DivX® is a video file compression
technology, developed by DivX, Inc.
DivX, DivX Certified, and associated
logos are trademarks of DivX, Inc. and are
used under license.
ABOUT DIVX VIDEO: DivX® is a
digital video format created by DivX,Inc.
This is an official DivX Certified device
that plays DivX video. Visit
www.divx.com for more information and
software tools to convert your files into
DivX video.
ABOUT DIVX VIDEO-ON-DEMAND:
This DivX Certified® device must be
registered in order to play DivX Video-on-
Demand (VOD) content. To generate the
registration code, locate the DivX VOD
section in the device setup menu. Go to
vod.divx.com with this code to complete
the registration process and learn more
about DivX VOD.
Manufactured under license from Dolby
Laboratories. Dolby and the double-D
symbol are trademarks of Dolby
Laboratories.
“BRAVIA” and are
trademarks of Sony Corporation.
“XMB
” and “XrossMediaBar” are
trademarks of Sony Corporation and Sony
Computer Entertainment Inc.
Location of the
identification label
Labels for Model No. and Power Supply
rating (in accordance with applicable
safety regulation) are located on the rear of
the TV.
The manufacturer of this product is
Sony Corporation, 1-7-1 Konan
Minato-ku Tokyo, 108-0075 Japan.
The Authorized Representative for
EMC and product safety is Sony
Deutschland GmbH, Hedelfinger
Strasse 61, 70327 Stuttgart,
Germany. For any service or
guarantee matters please refer to the
addresses given in separate service
or guarantee documents.
FUSE
FUSE
3
GB
Table of Contents
Checking the accessories ..............................................................................................................3
Inserting batteries into the remote .................................................................................................3
Setting Up
Attaching the Table-Top Stand ......................................................................................................4
Connecting an antenna (aerial)/Set Top Box/recorder (e.g. DVD recorder) ..................................5
Preventing the TV from toppling over ............................................................................................5
Bundling the cables........................................................................................................................6
Performing the initial set-up ...........................................................................................................6
Detaching the Table-Top Stand from the TV .................................................................................7
Watching TV
To watch programmes ...................................................................................................................8
To utilise the TV’s features ............................................................................................................8
To use i-Manual .............................................................................................................................9
Additional Information
Troubleshooting ...........................................................................................................................10
Specifications...............................................................................................................................11
Installing the Accessories (Wall-Mount Bracket)..........................................................................13
Safety Information........................................................................................................................16
Precautions ..................................................................................................................................17
Checking the accessories
AC power cord (mains lead) (1)
Cable holder (1)
Remote (1)
Size AAA batteries (R3 type) (2)
Table-Top Stand (1)*
1
Fixing screws for Table-Top Stand
(M5 × 16) (4)
Assembling screws for Table-Top Stand
(M5 × 16) (4)
(KDL-40HX803 only)
Stand rear cover (1)*
2
*
1
For KDL-40HX803, assemble the Table-Top
Stand with the supplied assembling screws.
Refer to the supplied Table-Top Stand leaflet to
assemble the stand.
*
2
For KDL-46HX803, the stand rear cover is
factory-attached to the Table-Top Stand.
Inserting batteries into the
remote
1 Remove the protection sheet.
2 Push and slide the cover upward.
Operating instructions are built into your BRAVIA TV. Refer to “To use i-Manual” for operation (page 9).
Before operating the TV, please read “Safety Information” (page 16). Retain this manual for future reference.
4
GB
Setting Up
Attaching the Table-Top
Stand
1 Refer to the supplied Table-Top Stand
leaflet for proper attachment for some
TV models.
2 Place the TV set on the Table-Top
Stand.
3 Fix the TV to the Table-Top Stand
according to the arrow marks that
guide the screw holes using the
supplied screws.
~
If using an electric screwdriver, set the tightening
torque at approximately 1.5 N·m {15 kgf·cm}.
4 For KDL-52/46HX903 and KDL-
40HX803, after all the screws are
tightened, attach the supplied stand rear
cover to the Table-Top Stand.
Adjusting the viewing angle of
the TV (KDL-52/46HX903 only)
This TV can be adjusted within the angles
shown below.
~
To return to 0°, reverse the above procedure.
1
4
2
3
Remove screw as
shown.
Install screw into
the top screw hole
of the Table-Top
Stand.
Slide in.Lift up and tilt.
5
GB
Setting Up
Connecting an antenna
(aerial)/Set Top Box/
recorder (e.g. DVD recorder)
Connecting a Set Top Box/recorder
(e.g. DVD recorder) with SCART
Connecting a Set Top Box/recorder
(e.g. DVD recorder) with HDMI
Preventing the TV from
toppling over
1 Install a wood screw (4 mm in
diameter, not supplied) in the TV stand.
2 Install a machine screw (M4 × 16, not
supplied) into the screw hole of the TV.
3 Tie the wood screw and the machine
screw with a strong cord (not supplied).
Set Top Box/recorder (e.g. DVD recorder)
Set Top Box/recorder (e.g. DVD recorder)
6
GB
Bundling the cables
~
Do not bundle the AC power cord (mains lead)
together with other cables.
Performing the initial set-up
1 Connect the TV to your AC power
outlet (mains socket).
2 Check the ENERGY SAVING
SWITCH setting is on (
z).
3 Press 1 on the TV.
When you switch on the TV for the first
time, the Language menu appears on the
screen.
Follow the instructions on the screen.
Digital Auto Tuning: When you select
“Cable”, we recommend that you select
“Quick Scan” for quick tuning. Set
“Frequency” and “Network ID” according
to the information supplied from your cable
provider. If no channel is found using
“Quick Scan”, try “Full Scan” (though it
may take some time).
For a list of compatible cable providers,
refer to the support web site:
http://support.sony-europe.com/TV/
DVBC/
4
7
GB
Setting Up
Programme Sorting: Changes the order of
analogue channels stored in the TV.
1 Press F/f to select the channel you want
to move to a new position, then press .
2 Press F/f to select the new position for
the channel, then press .
~
You can also tune channels manually.
Detaching the Table-Top
Stand from the TV
~
For KDL-52/46HX903 and KDL-40HX803,
remove the stand rear cover prior to detaching the
Table-Top Stand.
Remove the screws guided by the arrow marks
of the TV.
Do not remove the Table-Top Stand for any
reason other than to install corresponding
accessories on the TV.
Do not hold by the stand rear cover while carrying
the Table-Top Stand to prevent dropping the stand
which may cause an injury or damage to the
property.
8
GB
Watching TV
To watch programmes
To utilise the TV’s features
HOME button
Press to display various operation and setting
screens.
OPTIONS button
Press to display convenient functions based on
the current input or content.
z
The number 5, N, PROG + and AUDIO
buttons on the remote have a tactile dot.
Use the tactile dots as a reference when
operating the TV.
1
Turn on the TV.
1 Switch ENERGY SAVING SWITCH
on (
z).
2 Press 1 on the TV to turn on the TV.
2
Select a mode.
3
Select a TV channel.
Using Digital Electronic Programme
Guide
Press GUIDE in digital mode to display the
programme guide.
GUIDE
OPTIONS
HOME
2
3
Settings
TV
System Settings
Picture
Sound
SCART REC on
Add to Favourites
Lock/Unlock
PAP
Motionflow
Scene Select
Sleep Timer
Headphone Volume
Speakers
9
GB
Watching TV
To use i-Manual
x Welcome to i-Manual
x “BRAVIA” TV Features
x Watching TV
Introduces convenient features such as EPG
Guide, Favourites, etc.
x Using the Home Menu
Customise your TV settings, etc.
x Fun Features with Connected
Equipment
Introduces how to connect optional equipment.
x Parts Description
x Troubleshooting
Find solutions for your problem.
x Index
~
Images and illustrations may differ from what is displayed on the screen.
Operating instructions are built into your BRAVIA
TV and can be displayed on the screen.
To learn more about your TVs features you can
access your i-Manual with the touch of a button.
1
Press i-MANUAL.
2
Press G/g/F/f/ to select items.
1
2
10
GB
Additional Information
Troubleshooting
Check whether the 1 (standby) indicator is flashing in red.
When the 1 (standby) indicator is flashing
The self-diagnosis function is activated.
1 Count how many times the 1 (standby) indicator flashes between each three second
break.
For example, the indicator may flash three times, go off for three seconds, then flash again three
times.
2 Press 1 on the TV to turn it off, disconnect the AC power cord (mains lead), and inform
your dealer or Sony service centre of how the indicator flashes (number of flashes).
When the 1 (standby) indicator is not flashing
1 Check the items in the tables below. (Also refer to “Troubleshooting” in the i-Manual.)
2 If the problem persists, have your TV serviced by qualified service personnel.
Condition Explanation/Solution
Picture
There is no picture (screen
is dark) and no sound.
Check the antenna (aerial)/cable connection.
Connect the TV to the AC power (mains), and press 1 on the TV.
If the 1 (standby) indicator lights up in red, press "/1 or TV "/1
(button name differs by the remote).
Tiny black points and/or
bright points appear on the
screen.
The screen is composed of pixels. Tiny black points and/or bright
points (pixels) on the screen do not indicate a malfunction.
General
The TV’s power cannot be
turned on.
Check if ENERGY SAVING SWITCH is on (z).
The TV turns off
automatically (the TV
enters standby mode).
Check if the “Sleep Timer” is activated, or confirm the
“Duration” setting of “On Timer”.
Check if the “Idle TV Standby” is activated.
The remote does not
function.
Replace the batteries.
Your TV may be in SYNC mode.
Press SYNC MENU, select “TV Control” and then select “Home
(Menu)” or “Options” to control the TV.
The “Parental Lock”
password has been
forgotten.
Enter 9999 for the PIN code. (PIN code 9999 is always accepted.)
The TV surrounds become
warm.
When the TV is used for an extended period, the TV surrounds
become warm. You may feel hot when touching there by the
hand.
11
GB
Additional Information
Specifications
System
Panel system
LCD (Liquid Crystal Display) Panel
TV system
Analogue: Depending on your country/area selection: B/G/H, D/K, L, I
Digital: DVB-T2/DVB-T/DVB-C
Colour/video system
Analogue: PAL, PAL60 (only video input), SECAM, NTSC3.58, NTSC4.43 (only video input)
Digital: MPEG-2 MP@ML/HL, H.264/MPEG-4 AVC MP/HP@L4
Channel coverage
Analogue: VHF: E2–E12/UHF: E21–E69/CATV: S1–S20/HYPER: S21–S41
D/K: R1–R12, R21–R69/L: F2–F10, B–Q, F21–F69/I: UHF B21–B69
Digital: VHF/UHF
Sound output
10 W + 10 W
Input/Output jacks
Antenna (aerial) cable
75 ohm external terminal for VHF/UHF
/ AV1, 2
21-pin scart connector (CENELEC standard) including audio/video input, RGB input and TV audio/video
output.
COMPONENT IN
Supported formats: 1080p, 1080i, 720p, 576p, 576i, 480p, 480i
COMPONENT IN
Audio input (phono jacks)
HDMI IN1, 2, 3, 4
Video: 1080/24p, 1080p, 1080i, 720/24p, 720p, 576p, 576i, 480p, 480i
Audio: Two channel linear PCM: 32, 44.1 and 48 kHz, 16, 20 and 24 bits, Dolby Digital
Analogue audio input (minijack) (HDMI IN4 only)
PC Input
AV3
Video input (phono jack)
AV3
Audio input (phono jacks)
DIGITAL AUDIO OUT
(OPTICAL)
Digital optical jack (Two channel linear PCM, Dolby Digital)
(VAR/FIX)
Audio output (phono jacks)
PC IN
PC Input (Mini D-sub 15-pin)
PC audio input (minijack)
USB port
i
Headphones jack
CAM (Conditional Access Module) slot
LAN
10BASE-T/100BASE-TX connector (Depending on the operating environment of the network,
connection speed may differ. 10BASE-T/100BASE-TX communication rate and communication quality
are not guaranteed for this TV.)
* For LAN connections, use a Category 7 10BASE-T/100BASE-TX cable (not supplied).
3D SYNC
3D Sync terminal for optional transmitter
(Continued)
12
GB
*
1
Specified standby power is reached after the TV finishes necessary internal processes.
*
2
4 hours a days and 365 days a year
~
To save power consumption
when you reduce backlight setting (the brightness of the screen), the power consumption reduce.
the “Eco” settings (e.g. “Power Saving”, “Idle TV Standby”) help you to reduce the power consumption and
thus save money by reducing electricity bills.
when you switch off the TV using the ENERGY SAVING SWITCH, power consumption will be almost
zero.
Design and specifications are subject to change without notice.
Model name KDL- 52HX903 46HX903 46HX803 40HX803
Power and others
Power requirements
220 V – 240 V AC, 50 Hz
Screen size (measured
diagonally)
Approx. 132.2 cm/
52 inches
Approx. 116.8 cm/46 inches Approx. 101.6 cm/
40 inches
Display resolution
1,920 dots (horizontal) × 1,080 lines (vertical)
Power
consumption
in “Home”/
“Standard”
mode
136 W 130 W 102 W 88.0 W
in “Shop”/
“Vivid” mode
201 W 184 W 149 W 132 W
Standby power
consumption*
1
0.2 W (14 W when “Quick Start” is set to “On”)
Average annual energy
consumption*
2
199 kWh 190 kWh 149 kWh 128 kWh
Dimensions (Approx.) (w × h × d)
with Table-Top Stand
126.3 × 80.7 × 40.0 cm 112.4 × 72.7 × 40.0 cm 108.5 × 68.8 × 26.0 cm 95.2 × 61.3 × 25.0 cm
without Table-Top Stand
126.3 × 77.5 × 6.7 cm 112.4 × 69.5 × 6.7 cm 108.5 × 65.6 × 7.4 cm 95.2 × 58.1 × 7.4 cm
Mass (Approx.)
with Table-Top Stand
42.9 kg 36.2 kg 19.2 kg 16.4 kg
without Table-Top Stand
36.9 kg 30.2 kg 16.9 kg 14.2 kg
Supplied accessories
See “Checking the accessories” (page 3).
Optional accessories
Wall-Mount Bracket: SU-WL500
TV stand: SU-52HX1 (KDL-52HX903)
SU-46HX1 (KDL-46HX903)
3D Glasses: TDG-BR100/TDG-BR50
3D Sync Transmitter: TMR-BR100
13
GB
Additional Information
Installing the Accessories (Wall-Mount Bracket)
To Customers:
For product protection and safety reasons, Sony strongly recommends that installing of your TV be
performed by Sony dealers or licensed contractors. Do not attempt to install it yourself.
To Sony Dealers and Contractors:
Provide full attention to safety during the installation, periodic maintenance and examination of this
product.
Your TV can be installed using the SU-WL500 Wall-Mount Bracket (sold separately).
Refer to the Instructions supplied with the Wall-Mount Bracket to properly carry out the
installation.
Refer to “Detaching the Table-Top Stand from the TV” (page 7).
~
Place the TV on the Table-Top Stand, when securing the Mounting Hook.
Sufficient expertise is required for installing this product, especially to determine the strength of
the wall for withstanding the TV’s weight. Be sure to entrust the attachment of this product to the
wall to Sony dealers or licensed contractors and pay adequate attention to safety during the
installation. Sony is not liable for any damage or injury caused by mishandling or improper
installation.
Mounting Hook
Square hole
Screw
(+PSW
6 × 16)
(Continued)
14
GB
TV installation dimensions table
Unit: cm
Figures in the above table may differ slightly depending on the installation.
The wall that the TV will be installed on should be capable of supporting a weight of at least four
times that of the TV. Refer to “Specifications” (page 12) for its weight.
Model Name
KDL-
Display
dimensions
Screen centre
dimension
Length for each mounting angle
Angle (0°) Angle (20°)
AB C DEFGH
52HX903
126.3 77.5 7.7 48.2 12.0 34.8 73.5 50.6
46HX903
112.4 69.5 11.8 48.2 12.0 32.0 65.9 50.6
46HX803
108.5 65.6 9.5 43.1 12.1 32.3 61.6 45.4
40HX803
95.2 58.1 13.3 43.1 12.0 29.7 54.6 45.4
Screen centre point
WARNING
15
GB
Additional Information
Screw and Hook locations diagram/table
Model Name Screw location Hook location
KDL-52HX903
KDL-46HX903/46HX803
KDL-40HX803
e, j b
Screw location
When installing the Mounting Hook on the
TV.
Hook location
When installing the TV onto the Base Bracket.
b
a*
c*
* Hook location “a” and “c”
cannot be used for the models.
16
GB
Safety
Information
Installation/Set-up
Install and use the TV set in accordance
with the instructions below in order to
avoid any risk of fire, electrical shock or
damage and/or injuries.
Installation
The TV set should be installed near an
easily accessible mains socket.
Place the TV set on a stable, level
surface.
Only qualified service personnel should
carry out wall installations.
For safety reasons, it is strongly
recommended that you use Sony
accessories, including:
Wall-mount bracket SU-WL500
TV stand: SU-52HX1
(KDL-52HX903)
SU-46HX1
(KDL-46HX903)
Be sure to use the screws supplied with
the Wall-mount bracket when attaching
the mounting hooks to the TV set. The
supplied screws are designed so that they
are 8 mm to 12 mm in length when
measured from the attaching surface of
the mounting hook.
The diameter and length of the screws
differ depending on the Wall-mount
bracket model.
Use of screws other than those supplied
may result in internal damage to the TV
set or cause it to fall, etc.
Transporting
Before
transporting the
TV set, disconnect
all cables.
Two or three
people are needed
to transport a large
TV set.
When transporting
the TV set by
hand, hold it as
shown on the
right. Do not put
stress on the LCD
panel and the
frame around the
screen.
When lifting or
moving the TV
set, hold it firmly
from the bottom.
When transporting
the TV set, do not
subject it to jolts or
excessive
vibration.
When transporting
the TV set for
repairs or when moving, pack it using
the original carton and packing material.
Ventilation
Never cover the ventilation holes or
insert anything in the cabinet.
Leave space around the TV set as shown
below.
It is strongly recommended that you use
a Sony wall-mount bracket in order to
provide adequate air-circulation.
Installed on the wall
Installed with stand
To ensure proper ventilation and prevent
the collection of dirt or dust:
Do not lay the TV set flat, install
upside down, backwards, or
sideways.
Do not place the TV set on a shelf,
rug, bed or in a closet.
Do not cover the TV set with a cloth,
such as curtains, or items such as
newspapers, etc.
Do not install the TV set as shown
below.
Mains lead
Handle the mains lead and socket as
follows in order to avoid any risk of fire,
electrical shock or damage and/or injuries:
Use only mains leads supplied by
Sony, not other suppliers.
Insert the plug fully into the mains
socket.
Operate the TV set on a 220-240 V AC
supply only.
When wiring cables, be sure to unplug
the mains lead for your safety and take
care not to catch your feet on the
cables.
Disconnect the mains lead from the
mains socket before working on or
moving the TV set.
Keep the mains lead away from heat
sources.
Unplug the mains plug and clean it
regularly. If the plug is covered with
dust and it picks up moisture, its
insulation may deteriorate, which
could result in a fire.
Notes
Do not use the supplied mains lead on
any other equipment.
Do not pinch, bend, or twist the mains
lead excessively. The core conductors
may be exposed or broken.
Do not modify the mains lead.
Do not put anything heavy on the mains
lead.
Do not pull on the mains lead itself when
disconnecting the mains lead.
Do not connect too many appliances to
the same mains socket.
Do not use a poor fitting mains socket.
Prohibited Usage
Do not install/use the TV set in locations,
environments or situations such as those
listed below, or the TV set may
malfunction and cause a fire, electrical
shock, damage and/or injuries.
Location:
Outdoors (in direct sunlight), at the
seashore, on a ship or other vessel, inside a
vehicle, in medical institutions, unstable
locations, near water, rain, moisture or
smoke.
Environment:
Places that are hot, humid, or excessively
dusty; where insects may enter; where it
might be exposed to mechanical vibration,
near flammable objects (candles, etc). The
TV set shall not be exposed to dripping or
splashing and no objects filled with
liquids, such as vases, shall be placed on
the TV.
Situation:
Do not use when your hands are wet, with
the cabinet removed, or with attachments
not recommended by the manufacturer.
Disconnect the TV set from mains socket
and aerial during lightning storms.
Broken pieces:
Do not throw anything at the TV set. The
screen glass may break by the impact
and cause serious injury.
If the surface of the TV set cracks, do
not touch it until you have unplugged the
mains lead. Otherwise electric shock
may result.
When not in use
If you will not be using the TV set for
several days, the TV set should be
disconnected from the mains for
environmental and safety reasons.
As the TV set is not disconnected from
the mains when the TV set is just turned
off, pull the plug from the mains to
disconnect the TV set completely.
However, some TV sets may have
features that require the TV set to be left
in standby to work correctly.
For children
Do not allow children to climb on the
TV set.
Keep small accessories out of the reach
of children, so that they are not
mistakenly swallowed.
Mounting Hook
Hook attachment on rear
of TV set
Screw (supplied with the
Wall-mount bracket)
8 mm - 12 mm
For KDL-52/
46HX903
For KDL-46/
40HX803
30 cm
10 cm 10 cm
10 cm
Leave at least this space around
the set.
30 cm
10 cm
10 cm
6 cm
Leave at least this space around
the set.
Air circulation is blocked.
Wall Wall
17
GB
Additional Information
If the following problems
occur...
Turn off the TV set and unplug the mains
lead immediately if any of the following
problems occur.
Ask your dealer or Sony service centre to
have it checked by qualified service
personnel.
When:
Mains lead is damaged.
Poor fitting of mains socket.
TV set is damaged by being dropped,
hit or having something thrown at it.
Any liquid or solid object falls through
openings in the cabinet.
Warning
To prevent the spread of fire, keep candles
or other open flames away from this
product at all time.
Precautions
Viewing the TV
Some people may experience discomfort
(such as eye strain, fatigue, or nausea)
while watching 3D video images or
playing 3D video games. Sony
recommends that all viewers take regular
breaks while watching 3D video images
or playing 3D video games. The length
and frequency of necessary breaks will
vary from person to person. You must
decide what works best. If you
experience any discomfort, you should
stop watching the 3D video images or
playing 3D video games until the
discomfort ends; consult a doctor if you
believe necessary. You should also
review (i) the instruction manual of any
other device or media used with this
television and (ii) our website (http://
www.sony-europe.com/myproduct) for
the latest information. The vision of
young children (especially those under
six years old) is still under development.
Consult your doctor (such as a
pediatrician or eye doctor) before
allowing young children to watch 3D
video images or play 3D video games.
Adults should supervise young children
to ensure they follow the
recommendations listed above.
When using the simulated 3D function,
please note that the displayed image is
modified from the original due to the
conversion done by this television.
View the TV in moderate light, as
viewing the TV in poor light or during
long period of time, strains your eyes.
When using headphones, adjust the
volume so as to avoid excessive levels,
as hearing damage may result.
LCD Screen
Although the LCD screen is made with
high-precision technology and 99.99%
or more of the pixels are effective, black
dots may appear or bright points of light
(red, blue, or green) may appear
constantly on the LCD screen. This is a
structural property of the LCD screen
and is not a malfunction.
Do not push or scratch the front filter, or
place objects on top of this TV set. The
image may be uneven or the LCD screen
may be damaged.
If this TV set is used in a cold place, a
smear may occur in the picture or the
picture may become dark. This does not
indicate a failure. These phenomena
disappear as the temperature rises.
Ghosting may occur when still pictures
are displayed continuously. It may
disappear after a few moments.
The screen and cabinet get warm when
this TV set is in use. This is not a
malfunction.
The LCD screen contains a small
amount of liquid crystal. Some
fluorescent tubes used in this TV set also
contain mercury. Follow your local
ordinances and regulations for disposal.
Handling and cleaning the
screen surface/cabinet of
the TV set
Be sure to unplug the mains lead
connected to the TV set from mains socket
before cleaning.
To avoid material degradation or screen
coating degradation, observe the following
precautions.
To remove dust from the screen surface/
cabinet, wipe gently with a soft cloth. If
dust is persistent, wipe with a soft cloth
slightly moistened with a diluted mild
detergent solution.
Do not spray water or detergent directly
on the TV set. It may drip to the bottom
of the screen or exterior parts, and may
cause a malfunction.
Never use any type of abrasive pad,
alkaline/acid cleaner, scouring powder,
or volatile solvent, such as alcohol,
benzene, thinner or insecticide. Using
such materials or maintaining prolonged
contact with rubber or vinyl materials
may result in damage to the screen
surface and cabinet material.
Periodic vacuuming of the ventilation
openings is recommended to ensure to
proper ventilation.
When adjusting the angle of the TV set,
move it slowly so as to prevent the TV
set from moving or slipping off from its
table stand.
Optional Equipment
Keep optional components or any
equipment emitting electromagnetic
radiation away from the TV set.
Otherwise picture distortion and/or noisy
sound may occur.
This equipment has been tested and
found to comply with the limits set out in
the EMC Directive using a connection
signal cable shorter than 3 meters.
Batteries
Observe the correct polarity when
inserting batteries.
Do not use different types of batteries
together or mix old and new batteries.
Dispose of batteries in an
environmentally friendly way. Certain
regions may regulate the disposal of
batteries. Please consult your local
authority.
Handle the remote with care. Do not
drop or step on it, or spill liquid of any
kind onto it.
Do not place the remote in a location
near a heat source, a place subject to
direct sunlight, or a damp room.
Disposal of the TV set
Disposal of Old
Electrical &
Electronic
Equipment
(Applicable in
the European
Union and other European
countries with separate
collection systems)
This symbol on the product or on its
packaging indicates that this product shall
not be treated as household waste. Instead
it shall be handed over to the applicable
collection point for the recycling of
electrical and electronic equipment. By
ensuring this product is disposed of
correctly, you will help prevent potential
negative consequences for the
environment and human health, which
could otherwise be caused by
inappropriate waste handling of this
product. The recycling of materials will
help to conserve natural resources. For
more detailed information about recycling
of this product, please contact your local
Civic Office, your household waste
disposal service or the shop where you
purchased the product.
Disposal of
waste batteries
(applicable in the
European Union
and other
European
countries with separate
collection systems)
This symbol on the battery or on the
packaging indicates that the battery
provided with this product shall not be
treated as household waste. On certain
batteries this symbol might be used in
combination with a chemical symbol. The
chemical symbols for mercury (Hg) or
lead (Pb) are added if the battery contains
more than 0.0005% mercury or 0.004%
lead. By ensuring these batteries are
disposed of correctly, you will help
prevent potentially negative consequences
for the environment and human health
which could otherwise be caused by
inappropriate waste handling of the
battery. The recycling of the materials will
help to conserve natural resources. In case
of products that for safety, performance or
data integrity reasons require a permanent
connection with an incorporated battery,
this battery should be replaced by qualified
service staff only. To ensure that the
battery will be treated properly, hand over
the product at end-of-life to the applicable
collection point for the recycling of
electrical and electronic equipment. For all
other batteries, please view the section on
how to remove the battery from the
product safely. Hand the battery over to
the applicable collection point for the
recycling of waste batteries. For more
detailed information about recycling of
this product or battery, please contact your
local Civic Office, your household waste
disposal service or the shop where you
purchased the product.
18
GB
Television in the UK is going digital, bringing us all more.
Please see overleaf to find out when your area switches to digital.
Digital UK is the independent, non-profit organisation leading the process of digital TV switchover
in the UK. Digital UK provides impartial information on what people need to do to prepare for the
move to digital, and when they need to do it.
How the switchover affects your TV equipment:
Your new TV has a digital tuner built in, which means it is ready to receive the Freeview signal by
simply plugging it into your aerial socket (check if you can get digital TV through your aerial now,
or whether you'll have to wait until switchover, at www.digitaluk.co.uk).
When the TV switchover happens in your area, there are at least two occasions when you will need
to re-tune your TV in order to continue receiving your existing TV channels, and also to pick up new
ones. Digital UK, the body leading the digital TV switchover, will advise you when you need to re-
tune during the switchover.
Keep this Instruction
manual safe you’ll
need it
19
GB
How to re-tune:
1 Press "HOME" on the remote
2 Press G/g to select "Settings"
3 Press F/f to select "Digital Set-up", then press
4 Press to select "Digital Auto Tuning"
5Press G to select "Yes" then press to start "Digital Auto Tuning"
6 Follow the on screen instructions.
If you are missing any channels, it may be that they are not available in your area, or that your aerial
needs upgrading.
If you have any questions, please contact Sony on 08705 111 999 or call Digital UK on 0845 6 50 50
50 or visit www.digitaluk.co.uk
†Calls charged at BT rate of 3p per minute daytime and 1p per minute evenings and weekends.
Rates may vary for calls from non-BT lines.
4-180-175-11(1)
For useful information about Sony products
© 2010 Sony Corporation
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20

Sony 46HX803 User manual

Category
LED TVs
Type
User manual
This manual is also suitable for

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI