Intellinet 524636 User manual

Brand: Intellinet

Model: 524636

Category: Routers

Type: User manual

This manual is also suitable for

Wireless G 4-Port Router

wireless g

4-Port

router

user

manual

MODEL 524636

INT-524636-UM-0209-02

Contents

1 HARDWARE .................................................................................................................6

1.1 Front Panel / LEDs ...................... .........................................................................6

1.2 Rear Panel / Ports & Jacks ....................................................................................6

1.3 Connecting the Router ................. .........................................................................7

2 QUICK INSTALLATION .................. .............................................................................8

2.1 Time Zone ............................................................................................................10

2.2 LAN Settings ........................................................................................................10

2.3 WAN Interface .....................................................................................................11

2.3.1 Static IP .........................................................................................................12

2.3.2 DHCP Client ..................................................................................................12

2.3.3 PPPoE ...........................................................................................................13

2.3.4 PPTP .............................................................................................................13

2.4 Wireless Basic Settings .......................................................................................14

2.5 Wireless Security Settings ...................................................................................15

2.5.1 WEP ..............................................................................................................16

2.5.2 WPA (TKIP) ...................................................................................................17

2.5.3 WPA2 (AES) ..................................................................................................18

2.5.4 WPA2 (Mixed) ...............................................................................................18

3 GENERAL SETUP .......................... ...........................................................................20

3.1 System .................................................................................................................21

3.1.1 Time Zone Setting ...........................................................................................21

3.1.2 Password Setup ..............................................................................................22

3.1.3 Ping Testing ....................................................................................................22

3.2 WAN ....................................................................................................................23

3.2.1 Static IP .........................................................................................................24

3.2.2 DHCP Client ..................................................................................................25

3.2.3 PPPoE (PPP over Ethernet ...........................................................................26

3.2.4 PPTP .............................................................................................................27

3.2.5 DDNS ............................................................................................................28

3.3 LAN .....................................................................................................................30

3.4 Wireless ...............................................................................................................32

3.4.1 Basic Settings ................................................................................................32

3.4.2 Advanced Settings .........................................................................................33

3.4.3 Security .........................................................................................................35

3.4.4 Access Control ..............................................................................................36

3.5 Firewall ................................................................................................................37

3.5.1 URL Filtering .................................................................................................37

3.5.2 Port Filtering ..................................................................................................38

3.5.3 IP Filtering .....................................................................................................39

3.5.4 MAC Filtering .................................................................................................40

3.5.5 Port Forwarding .............................................................................................41

3.5.6 DMZ ...............................................................................................................42

4 STATUS ............................................. .......................................................................43

5 TOOLS ............................................. .......................................................................45

APPENDIX A ....................................... .......................................................................47

APPENDIX B ...................................... .......................................................................50

GLOSSARY ........................................ .......................................................................51

SPECIFICATIONS .............................. .......................................................................54

Thank you for purchasing the INTELLINET NETWORK SOLUTIONS

™

Wireless G 4-Port Router, Model 524636.

The Wireless G 4-Port Router lets you experience fast speeds as you

surf the Web, download music or photos, and play online games. This

wireless router works with 802.11g as well as the older 802.11b products,

and also includes a four-port 10/100 LAN switch so you can connect

using network cable or go wireless to satisfy all your needs.

Keeping intruders out of your network can be a challenge, and this

feature-rich wireless router is designed to make that challenge easier.

It includes a true rewall that secures your network against hackers.

With Network Address Translation (NAT) to shield your networked

devices from intruders, plus WEP, WPA and WPA2 encryption to conceal

your information on the wireless LAN from eavesdroppers, you can rest

assured that you’ve taken the necessary precautions to protect the

data on your network.

The easy-to-follow instructions in this user manual help make setup

and operation relatively simple, so you’ll soon be enjoying the benets

of these additional features:

• Compatible with all common DSL and cable Internet service providers

• Up to 54 Mbps network data transfer rate

• Supports MAC ltering for wireless clients

• Integrated 10/100 Mbps LAN switch with Auto MDI/MDI-X support

• DHCP server assigns IP addresses for all LAN users

• Supports DDNS (dynamic DNS)

• Supports UPNP (Universal Plug and Play)

• Supports virtual server and DMZ (demilitarized zone)

• VPN Pass Through (PPTP, IPSec, L2TP)

• Integrated anti-DoS rewall

• Content control through IP and Port lters

• Remote management function

• Easy installation through Web-based user interface

• Firmware updates via Web-based user interface

• Lifetime Warranty

NOTE: For a quick install procedure, refer to the printed quick install

guide enclosed with this product.

safety & ComPlianCe statements

FCC Part 15

This equipment has been tested and found to comply with the limits for

a Class B digital device, pursuant to Part 15 of Federal Communications

Commission (FCC) Rules. These limits are designed to provide reasonable

protection against harmful interference in a residential installation. This

equipment generates, uses and can radiate radio frequency energy and,

if not installed and used in accordance with the instructions, may cause

harmful interference to radio communications. However, there is no

guarantee that interference will not occur in a particular installation. If

this equipment does cause harmful interference to radio or television

reception, which can be determined by turning the equipment off and

on, the user is encouraged to try to correct the interference by one or

more of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and the receiver.

• Connect the equipment to an outlet on a circuit different from the

receiver.

• Consult the dealer or an experienced radio/TV technician for help.

FCC Caution

This equipment must be installed and operated in accordance with the

provided instructions, and a minimum of 20 cm of spacing must be

provided between the computer-mounted antenna and a person’s body

(excluding extremities of hands, wrist and feet) during wireless modes of

operation.

This device complies with Part 15 of the FCC Rules. Operation is subject

to the following two conditions: (1) this device may not cause harmful

interference, and (2) this device must accept any interference received,

including interference that may cause undesired operation.

Any changes or modications not expressly approved by the party

responsible for compliance could void the authority to operate equipment.

FCC Radiation Exposure Statement

This equipment complies with FCC radiation exposure limits set forth

for an uncontrolled environment. In order to avoid the possibility of

exceeding the FCC radio frequency exposure limits, human proximity

to the antenna shall not be less than 20 cm (8 inches) during normal

operation. The antenna(s) used for this transmitter must not be co-located

or operated in conjunction with any other antenna or transmitter. The

equipment version marketed in the U.S. is restricted to usage of the

channels 1-11 only.

R&TTE Compliance Statement

This equipment complies with all the requirements of Directive 1999/5/

EC of the European Parliament and the Council of March 9, 1999, on

radio equipment and telecommunication terminal equipment and the

mutual recognition of their conformity (R&TTE). The R&TTE directive

repeals and replaces Directive 98/13/EEC (Telecommunications Terminal

Equipment and Satellite Earth Station Equipment) as of April 8, 2000.

Safety

This equipment is designed with the utmost care for the safety of those

who install and use it. However, special attention must be paid to the

dangers of electric shock and static electricity when working with electrical

equipment. All guidelines must, therefore, be followed at all times to

ensure the safe use of the equipment.

EU Countries Intended for Use

he ETSI version of this device is intended for home and ofce use in

Austria, Belgium, Denmark, Finland, France, Germany, Greece, Ireland,

Italy, Luxembourg, the Netherlands, Portugal, Spain, Sweden and the

United Kingdom. The ETSI version of this device is also authorized for

use in EFTA member states Iceland, Liechtenstein, Norway and

Switzerland.

EU Countries Not Intended for Use

None.

HARDWARE

LED Status Description

PWR On Power is on.

Off Power is off.

WLAN On The Wireless LAN has been activated.

Flashing There is Wireless LAN activity (transferring or

receiving data).

Off The Wireless LAN has been deactivated.

WAN On The WAN has been connected.

Flashing There is WAN activity (transferring or receiving data).

Off There is no WAN connection.

1/2/3/4 On The LAN has been connected.

Flashing There is LAN activity (transferring or receiving data).

Off There is no LAN connection.

1 hardware

1.1 Front Panel / LEDs

The front panel of the Wireless G 4-Port Router

features LEDs that

provide an immediate

indication of the device’s

operational status.

1.2 Rear Panel / Ports & Jacks

The rear panel of the

Wireless G 4-Port

Router features these

ports, buttons and jacks (left to right):

• Four LAN 10/100 Mbps RJ-45 ports for connecting the router to local

PCs.

• WAN RJ-45 port for connecting the router to a cable, a DSL modem

or the Ethernet.

• Reset button (recessed), which allows you to do two things:

1. If problems occur with your router, press the button with a pencil

tip (for no more than 4 seconds) and the router will re-boot itself,

keeping your original congurations.

HARDWARE

2. If problems persist or you forget your password, press the button

for longer than 4 seconds and the router will reset itself to the

factory default settings. NOTE: Your original congurations will be

replaced with the factory default settings.

• Power adapter jack. NOTE: Only use the power adapter included

with the Wireless G 4-Port Router, as a different adapter could result

in product damage.

• Not shown is the 2 dB dipole antenna, which is connected to the rear

panel to the left of the RJ-45 ports.

1.3 Connecting the Router

Before installing the router, connect your PC to the Internet through

your broadband service. (If there is any problem, contact your ISP.)

Then proceed through the following steps.

1. Turn off your PC(s), cable/DSL modem and the router.

2. Adjust the antenna. Normally, upright is a good place to start.

3. Connect the PC(s) and each switch/hub on your local area network

to the LAN ports on the router.

4. Connect the ADSL/DSL/cable modem to the router WAN port.

5. Connect the power adapter between the power socket on the router

and an electrical outlet. The router will start to work automatically.

6. Turn on your PC(s) and the cable/(A)DSL modem.

Shown is a typical setup

for a local area network

(LAN) featuring the

Wireless G 4-Port

Router.

QUICK INSTALLATION

2 quiCk installation

This Quick Installation section can be used to begin router operation as

quickly as possible, requiring only minimal information in order to use

the router simply as an Internet access device. (A separate printed

Quick Install Guide — presenting the basic hardware conguration and

the Initial Setup below — is packaged with the Wireless G 4-Port

Router.)

First, set up your network; as shown above in Connecting the Router,

for example. Then congure your LAN PC clients so they can obtain

an IP address automatically. By default, the router’s Dynamic Host

Conguration Protocol (DHCP) is activated, meaning that once your

PCs have been congured to obtain an IP address automatically, all

the clients on the network will automatically obtain an IP address, as

well. If needed, refer to Appendix A at the back of this manual for the

Windows 2000, XP and Vista procedures; for other operating systems,

such as Mac and Sun, follow the OS manufacturer’s instructions.

Initial Setup

As stated above, once you have congured your PCs to obtain an IP

address automatically, the router’s DHCP server will automatically

give your LAN clients an IP address. To see if you have obtained an

IP address, see Appendix B at the back of this manual. NOTE: Make

sure that this Wireless G 4-Port Router’s DHCP server is the only

DHCP server available on your LAN. If there is another DHCP on your

network, then you’ll need to switch one of the DHCP servers off. (To

disable the router’s DHCP server, refer to Section 3: General Setup /

LAN Settings.)

Conrmed that the router has provided an IP address? Then continue

with the steps below!

1. Enter the default IP address

192.168.2.1 (the Wireless

G 4-Port Router’s IP

address) into your PC’s

Web browser and press the

Enter key.

QUICK INSTALLATION

2. When the login screen

displays, ll in the “User

Name” and “Password”

elds, then click “OK” to

the user name is “admin”

and the password is

“1234.” However, for

security reasons it is

recommended that you

change the password as

soon as possible (refer to

Section 3: General Setup / System / Password Setup).

3. When the Home screen displays (below), click “Quick Setup” to

continue with the Quick Installation procedure. The other three main

sections shown as menu options on the Home screen — General

Setup, Status Information and Tools — are presented and explained

in subsequent sections should you wish to use the many additional

advanced features of the Wireless G 4-Port Router.

QUICK INSTALLATION

2.1 Time Zone

On this screen, you can base the router’s time on these settings, which

will also affect functions such as log entries and rewall settings.

Time Zone Select: Select your local time zone from the drop-down

menu. The router will synchronize time according to your selection.

NTP server: Select the time server to synchronize with.

Click “Next” to proceed to the next screen.

2.2 LAN Settings

On this screen, you can congure the parameters for the local area

network.

QUICK INSTALLATION

IP Address: Enter the router’s LAN port IP address (your LAN clients’

default gateway IP address).

Subnet Mask: Specify a subnet mask for your LAN segment.

Click “Next” to proceed to the next screen.

2.3 WAN Interface

On this screen, select one of the four types of connections you’ll be

using — Static IP, DHCP Client, PPPoE or PPTP (as explained in the

subsections below) — to connect your router’s WAN port to your ISP.

NOTE: Different Internet service providers require different Internet

connection methods. Check with your ISP as to the type of connection

that is required.

WAN Access Type: Select one of the four connection options from

the drop-down menu, then click “Next” to proceed to the screen of

the selected connection type.

Static IP — Your ISP has given you an IP address already.

DHCP Client — Your ISP will automatically give you an IP address.

PPPoE — Your ISP requires you to use a Point-to-Point Protocol

over Ethernet (PPPoE) connection.

PPTP — Your ISP requires you to use a Point-to-Point Tunneling

Protocol (PPTP) connection.

QUICK INSTALLATION

2.3.1 Static IP

IP Address: Enter the IP address that your ISP has given you.

Subnet Mask: Enter the ISP-provided subnet mask; e.g.,255.255.255.0.

Default Gateway IP: Enter the ISP’s IP address gateway.

DNS: Enter the ISP’s DNS server IP address.

Click “Next” to proceed to the next screen.

2.3.2 DHCP Client

Hostname: Enter an optional hostname; e.g., “myhome.”

Click “Next” to proceed to the next screen.

QUICK INSTALLATION

2.3.3 PPPoE

User Name: Enter the username provided by your ISP.

Password: Enter the password provided by your ISP.

NOTE: Additional parameters, such as idle timeout, MTU size and

connection type, can be found in General Setup / LAN Setup.

Click “Next” to proceed to the next screen.

2.3.4 PPTP

IP Address: Enter the IP address your ISP has given you to establish

a PPTP connection.

QUICK INSTALLATION

Subnet Mask: Enter the ISP-provided subnet mask; e.g.,255.255.255.0.

Server IP Address: Enter the IP address of the ISP gateway.

User Name: Enter the username provided by your ISP for the PPTP

connection (sometimes referred to a the connection ID).

Password: Enter the password provided by your ISP.

Click “Next” to proceed to the next screen.

2.4 Wireless Basic Settings

This screen displays when you click “Next” after conguring any of the

four WAN interfaces above.

Band: This allows you to set the router (acting as an access point) as

802.11b or 802.11g mode. You can also select B+G mode to allow

the AP to select either 802.11b or 802.11g automatically.

SSID: Enter a name for the wireless LAN. All the devices in the same

wireless LAN should have the same ESSID.

Channel Number: Select the channel to be used by the wireless LAN.

All devices in the same wireless LAN should use the same channel.

Enable MAC Clone: Select to allow the router to copy the rst seen

MAC address to the WLAN MAC.

Click “Next” to proceed to the next screen.

QUICK INSTALLATION

2.5 Wireless Security Settings

Enabling WEP or WPA encryption can prevent unauthorized access to

your wireless network.

Encryption: Select one of the ve options from the drop-down menu,

then click “OK” to proceed to the screen of the selected option.

None — Do not apply any encryption to wireless usage: Everyone

has access without needing permission.

WEP — You can select the WEP key length for encryption: 64-bit

or 128-bit. A larger WEP key length will provide a higher level of

security, but the throughput will be lower.

WPA (TKIP) — You can use a pre-shared key to authenticate

wireless stations and encrypt data during communication. Use

TKIP to change the encryption key frequently.

WPA2 (AES) — You can use a pre-shared key to authenticate

wireless stations and encrypt data during communication. Use

CCMP (AES) to change the encryption key frequently.

WPA2 Mixed — This will automatically select TKIP or AES based

on the other communication peer.

QUICK INSTALLATION

2.5.1 WEP

When you select either a 64-bit or 128-bit WEP key, you need to enter

WEP keys to encrypt data. You can generate the key by yourself and

enter it; you can also enter four WEP keys and select one of them as

the default key. Then the router can receive any packets encrypted by

one of the four keys.

Key Length: Select the WEP key length for encryption: 64-bit or 128-

bit. A larger WEP key length will provide a higher level of security,

but the throughput will be lower.

Key Format: Select ASCII characters (alphanumeric format) or hexa-

decimal digits (in the “A-F,” “a-f” and “0-9” range) to be the WEP key.

For example, ASCII characters: “guest”; hexadecimal digits:

“12345abcde.”

Default Tx Key: Select one of the four keys as the default key to

encrypt your data.

Encryption Key 1–4: The WEP keys are used to encrypt data

transmitted in the wireless network. Fill in the elds using the

following guidelines.

• 64-bit WEP: Input 10-digit hex values (in the “A-F,” “a-f” and “0-9”

range) or 5-digit ASCII characters as the encryption keys.

QUICK INSTALLATION

• 128-bit WEP: Input 26-digit hex values (in the “A-F,” “a-f” and “0-9”

range) or 13-digit ASCII characters as the encryption keys.

Click “OK” to save and activate all the settings. Now you can use the

router as your Internet gateway.

2.5.2 WPA (TKIP)

Wi-Fi Protected Access (WPA) is an advanced security standard that

lets you use a pre-shared key to authenticate wireless stations and

encrypt data during communication. It uses TKIP to frequently change

the encryption key, making it difcult for hackers to break through and

thus greatly improving security.

Pre-Shared Key Format: Select “Passphrase” (alphanumeric format)

or “Hexadecimal Digits” (in the “A-F,” “a-f” and “0-9” range) for the

pre-shared key. For example, passphrase: “iamguest”; hex digits:

“12345abcde.”

Pre-Shared Key: The pre-shared key is used to authenticate and encrypt

data transmitted in the wireless network. Fill in the elds using the

following guidelines.

• Hex: Input 64-digit hex values (in the “A-F,” “a-f” and “0-9” range)

or at least an 8-character passphrase as the pre-shared keys.

Click “OK” to save and activate all the settings. Now you can use the

router as your Internet gateway.

QUICK INSTALLATION

2.5.3 WPA2 (AES)

Wi-Fi Protected Access 2 (WPA2) is an advanced security standard that

lets you use a pre-shared key to authenticate wireless stations and

encrypt data during communication. It uses CCMP (AES) to frequently

change the encryption key, making it difcult for hackers to break

through and thus greatly improving security.

Pre-Shared Key Format: Select “Passphrase” (alphanumeric format)

or “Hexadecimal Digits” (in the “A-F,” “a-f” and “0-9” range) for the

pre-shared key. For example, passphrase: “iamguest”; hex digits:

“12345abcde.”

Pre-Shared Key: This is used to authenticate and encrypt data

transmitted in the wireless network. Fill in the elds using the

following guidelines.

• Hex: Input 64-digit hex values (in the “A-F,” “a-f” and “0-9” range)

or at least an 8-character passphrase as the pre-shared keys.

Click “OK” to save and activate all the settings. Now you can use the

router as your Internet gateway.

2.5.4 WPA2 Mixed

Wi-Fi Protected Access 2 (WPA2) is an advanced security standard that

lets you use a pre-shared key to authenticate wireless stations and

encrypt data during communication. This option uses TKIP or CCMP

QUICK INSTALLATION

(AES) to frequently change the encryption key, making it difcult for

hackers to break through and thus greatly improving security.

Pre-Shared Key Format: Select “Passphrase” (alphanumeric format)

or “Hexadecimal Digits” (in the “A-F,” “a-f” and “0-9” range) for the

pre-shared key. For example, passphrase: “iamguest”; hex digits:

“12345abcde.”

Pre-Shared Key: This is used to authenticate and encrypt data

transmitted in the wireless network. Enter either a 64-digit hex value

(in the “A-F,” “a-f” and “0-9” range) or at least an 8-character

passphrase.

Click “OK” to save and activate all the settings. Now you can use the

router as your Internet gateway.

GENERAL SETUP

3 general setuP

Clicking “General Setup” on the Home Page — which displays when

the initial setup is completed (see Quick Installation) — displays the

screen below. If you already congured the Quick Setup Wizard, you

don’t need to congure anything in the General Setup section in order

to start using the Internet. This section does, however, allow you to

congure the router to meet your network’s more specic needs by using

advanced features such as address mapping, access control, hacker-

attack prevention and DMZ.

To access the various conguration screens, click/select one of the ve

subsections listed on the left-hand menu and briey described below.

System: This section allows you to congure the router’s system time

zone and password, and utilize ping testing.

WAN: This section allows you to select the connection method in order

to establish a connection with your ISP (as in the Quick Installation

section).

LAN: This section allows you to specify the LAN segment’s IP address

and subnet mask, enable/disable DHCP and select an IP range for

the LAN.

Wireless: This section allows you to set up the wireless LAN’s SSID,

WEP key and MAC ltering.

Firewall: This section allows you to congure access control, hacker-

attack prevention and DMZ.

Page is loading ...

Intellinet 524636 User manual

Brand: Intellinet

Model: 524636

Category: Routers

Type: User manual

This manual is also suitable for

Wireless G 4-Port Router

Download PDF

report

Intellinet 524636 User manual

This manual is also suitable for

Intellinet 524636 User manual

Related papers

Other documents