Dell 13 Owner's manual

Category
Notebooks
Type
Owner's manual

This manual is also suitable for

Dell Latitude 3340
Owner's Manual
Regulatory Model: P47G
Regulatory Type: P47G001
Notes, Cautions, and Warnings
NOTE: A NOTE indicates important information that helps you make better use of your computer.
CAUTION: A CAUTION indicates either potential damage to hardware or loss of data and tells you
how to avoid the problem.
WARNING: A WARNING indicates a potential for property damage, personal injury, or death.
Copyright © 2014 Dell Inc. All rights reserved. This product is protected by U.S. and international copyright and
intellectual property laws. Dell
and the Dell logo are trademarks of Dell Inc. in the United States and/or other
jurisdictions. All other marks and names mentioned herein may be trademarks of their respective companies.
2014 -03
Rev. A00
Contents
1 Working on Your Computer...................................................................................5
Before Working Inside Your Computer................................................................................................ 5
Turning Off Your Computer..................................................................................................................7
After Working Inside Your Computer................................................................................................... 7
2 Removing and Installing Components................................................................9
Recommended Tools............................................................................................................................9
System Overview...................................................................................................................................9
Removing the Battery..........................................................................................................................12
Installing the Battery............................................................................................................................12
Removing the Subscriber Identity Module (SIM) Card....................................................................... 12
Installing the SIM Card.........................................................................................................................13
Removing the Base Cover...................................................................................................................13
Installing the Base Cover.....................................................................................................................14
Removing the Memory........................................................................................................................14
Installing the Memory..........................................................................................................................15
Removing the Keyboard Trim............................................................................................................. 15
Installing the Keyboard Trim............................................................................................................... 16
Removing the Keyboard......................................................................................................................16
Installing the Keyboard........................................................................................................................18
Removing the Coin-Cell Battery.........................................................................................................18
Installing the Coin-Cell Battery...........................................................................................................19
Removing the Audio-Connector Board............................................................................................. 19
Installing the Audio-Connector Board...............................................................................................20
Removing the Hard Drive................................................................................................................... 20
Installing the Hard Drive......................................................................................................................21
Removing the Speakers.......................................................................................................................21
Installing the Speakers........................................................................................................................ 22
Removing the Wireless Local Area Network (WLAN) Card................................................................23
Installing the WLAN Card....................................................................................................................23
Removing the Wireless Wide Area Network (WWAN) Card...............................................................24
Installing the WWAN Card.................................................................................................................. 24
Removing the System Fan ................................................................................................................. 25
Installing the System Fan.....................................................................................................................27
Removing the Heatsink....................................................................................................................... 27
Installing the Heatsink.........................................................................................................................28
Removing the Display Assembly ........................................................................................................28
Installing the Display Assembly.......................................................................................................... 30
Removing the System Board...............................................................................................................31
Installing the System Board................................................................................................................ 32
3 System Setup........................................................................................................... 35
Boot Sequence....................................................................................................................................35
Navigation Keys................................................................................................................................... 35
System Setup Options.........................................................................................................................36
Updating the BIOS ............................................................................................................................. 44
System and Setup Password...............................................................................................................45
Assigning a System Password and Setup Password.................................................................... 45
Deleting or Changing an Existing System and/or Setup Password.............................................46
4 Diagnostics...............................................................................................................47
Enhanced Pre-Boot System Assessment (ePSA) Diagnostics........................................................... 47
Device Status Lights............................................................................................................................48
Battery Status Lights........................................................................................................................... 48
5 Technical Specifications.......................................................................................49
6 Contacting Dell....................................................................................................... 55
1
Working on Your Computer
Before Working Inside Your Computer
Use the following safety guidelines to help protect your computer from potential damage and to help to
ensure your personal safety. Unless otherwise noted, each procedure included in this document assumes
that the following conditions exist:
You have read the safety information that shipped with your computer.
A component can be replaced or--if purchased separately--installed by performing the removal
procedure in reverse order.
WARNING: Before working inside your computer, read the safety information that shipped with
your computer. For additional safety best practices information, see the Regulatory Compliance
Homepage at www.dell.com/regulatory_compliance
CAUTION: Many repairs may only be done by a certified service technician. You should only
perform troubleshooting and simple repairs as authorized in your product documentation, or as
directed by the online or telephone service and support team. Damage due to servicing that is
not authorized by Dell is not covered by your warranty. Read and follow the safety instructions
that came with the product.
CAUTION: To avoid electrostatic discharge, ground yourself by using a wrist grounding strap or
by periodically touching an unpainted metal surface, such as a connector on the back of the
computer.
CAUTION: Handle components and cards with care. Do not touch the components or contacts
on a card. Hold a card by its edges or by its metal mounting bracket. Hold a component such as a
processor by its edges, not by its pins.
CAUTION: When you disconnect a cable, pull on its connector or on its pull-tab, not on the cable
itself. Some cables have connectors with locking tabs; if you are disconnecting this type of cable,
press in on the locking tabs before you disconnect the cable. As you pull connectors apart, keep
them evenly aligned to avoid bending any connector pins. Also, before you connect a cable,
ensure that both connectors are correctly oriented and aligned.
NOTE: The color of your computer and certain components may appear differently than shown in
this document.
To avoid damaging your computer, perform the following steps before you begin working inside the
computer.
1. Ensure that your work surface is flat and clean to prevent the computer cover from being scratched.
2. Turn off your computer (see Turning Off Your Computer).
5
3. If the computer is connected to a docking device (docked) such as the optional Media Base or
Battery Slice, undock it.
CAUTION: To disconnect a network cable, first unplug the cable from your computer and
then unplug the cable from the network device.
4. Disconnect all network cables from the computer.
5. Disconnect your computer and all attached devices from their electrical outlets.
6. Close the display and turn the computer upside-down on a flat work surface.
NOTE: To avoid damaging the system board, you must remove the main battery before you
service the computer.
7. Remove the main battery.
8. Turn the computer top-side up.
9. Open the display.
10. Press the power button to ground the system board.
CAUTION: To guard against electrical shock, always unplug your computer from the
electrical outlet before opening the display.
CAUTION: Before touching anything inside your computer, ground yourself by touching an
unpainted metal surface, such as the metal at the back of the computer. While you work,
periodically touch an unpainted metal surface to dissipate static electricity, which could
harm internal components.
11. Remove any installed ExpressCards or Smart Cards from the appropriate slots.
6
Turning Off Your Computer
CAUTION: To avoid losing data, save and close all open files and exit all open programs before
you turn off your computer.
1. Shut down the operating system:
In Windows 8.1:
* Using a touch-enabled device:
a. Swipe in from the right edge of the screen, opening the Charms menu and select
Settings.
b. Select the and then select Shut down.
* Using a mouse:
a. Point to upper-right corner of the screen and click Settings.
b. Click the and select Shut down.
In Windows 7:
1. Click Start .
2. Click Shut Down.
or
1. Click Start .
2. Click the arrow in the lower-right corner of the Start menu as shown below, and then click
Shut Down .
2. Ensure that the computer and all attached devices are turned off. If your computer and attached
devices did not automatically turn off when you shut down your operating system, press and hold
the power button for about 6 seconds to turn them off.
After Working Inside Your Computer
After you complete any replacement procedure, ensure you connect any external devices, cards, and
cables before turning on your computer.
CAUTION: To avoid damage to the computer, use only the battery designed for this particular
Dell computer. Do not use batteries designed for other Dell computers.
1. Connect any external devices, such as a port replicator, battery slice, or media base, and replace any
cards, such as an ExpressCard.
2. Connect any telephone or network cables to your computer.
CAUTION: To connect a network cable, first plug the cable into the network device and then
plug it into the computer.
3. Replace the battery.
4. Connect your computer and all attached devices to their electrical outlets.
7
5. Turn on your computer.
8
2
Removing and Installing Components
This section provides detailed information on how to remove or install the components from your
computer.
Recommended Tools
The procedures in this document may require the following tools:
Small flat-blade screwdriver
#0 Phillips screwdriver
#1 Phillips screwdriver
Small plastic scribe
System Overview
Figure 1. Front view
1. display 2. keyboard
3. keyboard trim
9
Figure 2. Features
1. microphone
2. camera
3. camera-status light
4. security cable slot
5. power button
6. USB 3.0 connector
7. status lights
8. audio connector
9. memory card reader
10. touchpad
11. speakers
12. network-status light
13. USB 3.0 connector with PowerShare
10
14. mini DisplayPort connector
15. HDMI connector
16. air vents
17. network connector
18. power connector
Figure 3. Inside view — Back
1. power connector 2. system fan
3. heatsink 4. speaker
5. memory module 6. hard drive
7. audio-connector board 8. WLAN card
9. system board 10. coin-cell battery
11
Removing the Battery
1. Follow the procedures in Before Working On Your Computer.
2. Slide the release latches to unlock position and pull the battery to remove from the computer.
Installing the Battery
1. Insert the battery into its slot until the battery clicks into place.
2. Follow the procedures in After Working Inside Your Computer.
Removing the Subscriber Identity Module (SIM) Card
1. Follow the procedures in Before Working on Your Computer.
2. Remove the battery.
12
3. Press in to release the SIM card and pull the SIM card out to remove from the computer.
Installing the SIM Card
1. Insert the SIM card into its slot on the computer and press till it clicks in place.
2. Install the battery.
3. Follow the procedures in After Working Inside Your Computer.
Removing the Base Cover
1. Follow the procedures in Before Working On Your Computer.
2. Remove the battery.
13
3. Perform the following steps to remove the base cover from the computer:
a) Remove the screws that secure the base cover to the computer.
b) Pry the edges of the base cover and remove the base cover from the computer.
Installing the Base Cover
1. Align the edges of the base cover on the computer and press it on the computer until it snaps in
place.
2. Tighten the screws to secure the base cover to the computer.
3. Install the battery.
4. Follow the procedures in After Working Inside Your Computer.
Removing the Memory
1. Follow the procedures in Before Working On Your Computer.
2. Remove the:
a) battery
b) base cover
3. Perform the following steps to remove the memory module(s) from the computer:
a) Pry the retention clips away from the memory module(s) till the memory module(s) pop up.
b) Remove the memory module(s) from the computer.
14
Installing the Memory
1. Insert the memory module into the memory socket and press until the memory module click in to
place.
2. Install the:
a) base cover
b) battery
3. Follow the procedures in After Working Inside Your Computer.
Removing the Keyboard Trim
1. Follow the procedures in Before Working Inside Your Computer.
2. Pry up the keyboard trim starting from the bottom and work your way along the top edge.
15
3. Remove the keyboard trim from the computer.
Installing the Keyboard Trim
1. Align the keyboard trim to its place.
2. Press along the sides of the keyboard trim until it snaps in place.
3. Follow the procedures in After Working Inside Your Computer.
NOTE: You may also need to press the center of the keyboard trim to install the keyboard trim
in its place.
Removing the Keyboard
1. Follow the procedures in Before Working On Your Computer.
2. Remove the:
a) battery
b) keyboard trim
16
3. Remove the screws that secure the keyboard to the computer.
4. Slide and lift the keyboard from the computer to access the keyboard cable.
17
5. Flip over the keyboard, disconnect the keyboard cable from its connector, and remove the keyboard
from the computer.
Installing the Keyboard
1. Connect the keyboard cable to its connector on the computer.
2. Install the keyboard in its place.
3. Tighten the screws to secure the keyboard to the computer.
4. Install the:
a) keyboard trim
b) battery
5. Follow the procedures in After Working Inside Your Computer.
Removing the Coin-Cell Battery
1. Follow the procedures in Before Working on Your Computer
2. Remove:
a) battery
b) base cover
18
3. Perform the following steps to remove the coin-cell battery from the computer:
a) Disconnect the coin-cell battery cable from the system board.
b) Pull the coin-cell battery to detach the adhesive underneath which attaches it to the computer.
c) Remove the coin-cell battery from the computer.
Installing the Coin-Cell Battery
1. Connect the coin-cell battery cable to the system board.
2. Press down the coin-cell battery on the computer.
3. Install the:
a) base cover
b) battery
4. Follow the procedures in After Working Inside Your Computer.
Removing the Audio-Connector Board
1. Follow the procedures in Before Working On Your Computer.
2. Remove the:
a) battery
b) base cover
19
3. Perform the following steps to remove the audio-connector board from the computer:
a) Disconnect the audio-connector board cable from the system board.
b) Remove the screw that secures the audio-connector board to the computer.
c) Lift and remove the audio-connector board from the computer.
Installing the Audio-Connector Board
1. Place the audio-connector board in its slot on the computer.
2. Tighten the screw to secure the audio-connector board to the computer.
3. Connect the audio-connector board cable to the system board.
4. Install the:
a) base cover
b) battery
5. Follow the procedures in After Working Inside Your Computer.
Removing the Hard Drive
1. Follow the procedures in Before Working On Your Computer.
2. Remove the:
a) battery
b) base cover
20
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42
  • Page 43 43
  • Page 44 44
  • Page 45 45
  • Page 46 46
  • Page 47 47
  • Page 48 48
  • Page 49 49
  • Page 50 50
  • Page 51 51
  • Page 52 52
  • Page 53 53
  • Page 54 54
  • Page 55 55

Dell 13 Owner's manual

Category
Notebooks
Type
Owner's manual
This manual is also suitable for

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI