Panasonic CS-UE12JKE Datasheet

(Guangzhou) Co., Ltd. 2008. Unauthorized copying

and distribution is a violation of law.

Order No: PHA-AG0903005C2

Indoor Unit Outdoor Unit

CS-UE9JKE

CS-UE12JKE

CU-UE9JKE

CU-UE12JKE

TABLE OF CONTENTS

1. Safety Precautions.............................................3

2. Specification.......................................................5

2.1 CS-UE9JKE CU-UE9JKE ............................5

2.2 CS-UE12JKE CU-UE12JKE ........................7

3.

Features ..............................................................9

4. Location of Controls and Components .........10

4.1 Indoor Unit..................................................10

4.2 Outdoor Unit...............................................10

4.3 Remote Control..........................................10

5. Dimensions.......................................................11

5.1 Indoor Unit..................................................11

5.2 Outdoor Unit...............................................13

6. Refrigeration Cycle Diagram...........................14

7. Block Diagram..................................................15

8. Wiring Connection Diagram............................16

8.1

CS-UE9JKE CU-UE9JKE ..........................18

8.2 CS-UE12JKE CU-UE12JKE ......................19

9.

Installation Instruction.....................................18

9.1 Select the Best Location ............................18

9.2 Indoor Unit..................................................19

9.3 Outdoor Unit...............................................21

10. Service Mode....................................................24

10.1 Auto OFF/ON Button..................................24

10.2 Select Remote Control Transmission Code24

10.3 Operate and Display of Remote Control....25

11. Operation Control.............................................27

11.1 Basic Function............................................27

11.2 Indoor Fan Motor Operation.......................28

11.3 Outdoor Fan Motor Operation....................28

12. Protection control ............................................31

This service information is designed for experienced repair technicians only and is not designed for use by the general public.

It does not contain warnings or cautions to advise non-technical individuals of potential dangers in attempting to service a product.

Products powered by electricity should be serviced or repaired only by experienced professional technicians. Any attempt to service

or repair the products dealt with in this service information by anyone else could result in serious injury or death.

WARNING

2

12.1

Protection Control For All Operations.........31

12.2 Protection Control For Cooling and Soft Dry

Operation....................................................32

12.3 Outdoor Air Temperature Control...............33

13. Troubleshooting Guide....................................35

13.1 Refrigeration Cycle System........................35

13.2 Break Down self Diagnosis Function..........35

14.

Disassembly and Assembly Instructions......38

15. Exploded View and Replacement Pars List...41

15.1 Indoor Unit..................................................41

15.2 Outdoor Unit...............................................43

3

CAUTION

WARNING

1. Safety Precautions

• Read the following “SAFETY PRECAUTIONS” carefully before perform any servicing.

• Electrical work must be installed or serviced by a licensed electrician. Be sure to use the correct rating of the

power plug and main circuit for the model installed.

• The caution items stated here must be followed because these important contents are related to safety. The

meaning of each indication used is as below. Incorrect installation or servicing due to ignoring of the instruction

will cause harm or damage, and the seriousness is classified by the following indications.

This indication shows the possibility of causing death or serious injury

This indication shows the possibility of causing injury or damage to properties.

• The items to be followed are classified by the symbols:

• Carry out test run to confirm that no abnormality occurs after the servicing. Then, explain to user the operation,

care and maintenance as stated in instructions. Please remind the customer to keep the operating instructions for

future reference.

1. Engage dealer or specialist for installation. If installation done by the user is defective, it will cause water leakage,

electrical shock or fire.

2. Install according to this installation instructions strictly. If installation is defective, it will cause water leakage, electrical

shock or fire.

3. Use the attached accessories parts and specified parts for installation. Otherwise, it will cause the set to fall, water

leakage, fire or electrical shock.

4. Install at a strong and firm location which is able to withstand the set’s weight. If the strength is not enough or

installation is not properly done, the set will drop and cause injury.

5. Do not install outdoor unit near handrail of veranda. When installing air-conditioner unit at veranda of high rise

building, child may climb up to outdoor unit and cross over the handrail and causing accident.

6. For electrical work, follow the local national wiring standard, regulation and this installation instruction. An independent

circuit and single outlet must be used. If electrical circuit capacity is not enough or defect found in electrical work, it will

cause electrical shock or fire.

7. This equipment is strongly recommended to be installed with Earth Leakage Circuit Breaker (ELCB) or Residual

Current Device (RCD). Otherwise, it may cause electrical shock and fire in case equipment breakdown or insulation

breakdown.

8. This equipment must be properly earthed. Earth line must not be connected to gas pipe, water pipe, earth of lightning

rod and telephone. Otherwise, it may cause electrical shock in case equipment breakdown or insulation breakdown.

9. Use the specified cable (1.5 mm

2

) and connect tightly for indoor/outdoor connection. Connect tightly and clamp the

cable so that no external force will be acted on the terminal. If connection or fixing is not perfect, it will cause heat-up

or fire at the connection.

10. Wire routing must be properly arranged so that control board cover is fixed properly. If control board cover is not fixed

perfectly, it will cause fire or electrical shock.

11. When carrying out piping connection, take care not to let air substances other than the specified refrigerant go into

refrigeration cycle. Otherwise, it will cause lower capacity, abnormal high pressure in the refrigeration cycle, explosion

and injury.

12. Do not damage or use unspecified power supply cord. Otherwise, it will cause fire or electrical shock.

13. Do not modify the length of the power supply cord or use extension cord, and do not share the single outlet with other

electrical appliances. Otherwise, it will cause fire or electrical shock.

14. • For R410A models, when connecting the piping, do not use any existing (R22) pipes and flare nuts. Using such same

may cause abnormally high pressure in the refrigeration cycle (piping), and possibly result in explosion and injury. Use

only R410A materials.

• Thickness or copper pipes used with R410A must be more than 0.8 mm. Never use copper pipes thinner than 0.8 mm

• It is desirable that the amount of residual oil is less than 40 mg/10 m.

15. During installation, before run the compressor, confirm the refrigeration pipes are fixed. Operation of compressor

without fixing the piping, setting the 2 way valve and 3-way valve at open condition, a burst may occur and cause

injury.

16. During pump down operation, stop the compressor before remove the refrigeration piping. When remove piping while

2-way valve, 3 way valve at open condition, burst may occur and cause injury.

Symbol with white background denotes item that is PROHIBITED from doing.

Symbol with dark background denotes item that must be carried out.

4

CAUTION

17. After completion of installation, confirm there is no leakage of refrigerant gas. It may generate toxic gas when the

refrigerant contacts with fire.

18. Ventilate if there is refrigerant gas leakage during operation. It may cause toxic gas when the refrigerant contacts with

fire.

19. Recommended installation height for indoor unit shall be at least 2.5 m.

20. The appliance shall be installed in accordance with national wiring regulations.

21. Keep away from small children, the thin film may cling to nose and mouth and prevent breathing.

22. Do not insert your fingers or other objects into the unit, high speed rotating fan may cause injury.

23. Do not modify the machine, part, material during repairing service.

24. Must not use other parts except original parts describe in catalog and manual.

1. Do not install the unit at place where leakage of flammable gas may occur. In case gas leaks and accumulates at

surrounding of the unit, it may cause fire.

2. Carry out drainage piping as mentioned in installation instructions. If drainage is not perfect, water may enter the room

and damage the furniture.

3. Tighten the flare nut with torque wrench according to specified method. If the flare nut is over-tightened, after a long

period, the flare may break and cause refrigerant gas leakage.

4. Do not touch outdoor unit air inlet and aluminums fin. It may cause injury.

5. Select an installation location which is easy for maintenance.

6. Power supply connection to the air conditioner.

Connect the power supply cord of the air conditioner to the mains using one of the following methods.

Power supply point should be in easily accessible place for power disconnection in case of emergency.

In some countries, permanent connection of this air conditioner to the power supply is prohibited.

1) Power supply connection to the receptacle using a power plug.

Use an approved 15/16A power plug with earth pin for the connection to the receptacle.

2) Power supply connection to a circuit breaker for the permanent connection. Use an approved 16A circuit breaker for

the permanent connection. It must be a double pole switch with a minimum 3.5 mm contact gap.

7. Do not release refrigerant.

Do not release refrigerant during piping work for installation, re-installation and during repairing a refrigeration parts.

Take care of the liquid refrigerant, it may cause frostbite.

8. Installation and service work.

It may need two people to carry out the installation and service work.

9. Do not install this appliance in a laundry room or other location where water may drip from the ceiling, etc.

10. Do not sit ot step on the unit, you may fall down accidentally.

11. Do not touch the sharp aluminium fin, sharp parts may cause injury.

12. Thermal fuse specification for indoor unit: 250V 3.15A T3.15AL; outdoor unit: 205V 3.15A T3.15AL,205V 20A T20AL.

5

2. Specification

2.1 CS-UE9JKE CU-UE9JKE

Item Unit Indoor Unit Outdoor Unit

kW 2.50(0.90~3.00) Capacity

BTU/h 8530(3070~10230)

W/W 3.33(4.73~3.00) EER

BTU/hW 11.37(16.15~10.23)

dB(A) Hi: 42 Lo: 27 QLo: 22 Hi: 46

COOLING

Noise Level

Power level dB 53 59

kW 3.30(0.90~4.00) Capacity

BTU/h 11260(3070~13650)

W/W 3.66(4.09~3.33) COP

BTU/hW 12.51(13.95~11.37)

dB(A) Hi: 42 Lo: 27 QLo: 25 Hi: 47

HEATING

Noise Level

Power level dB 53 60

l/h 1.4 Moisture Removal

(pt/h) 2.4

Lo m

3

/m (ft

3

/m) 6.15(232) -

Me m

3

/m (ft

3

/m) 7.93(300) -

Air Volume

Hi m

3

/m (ft

3

/m) 10.08 (381) 28.9(1020)

Refrigerant Control Device - Capillary Tube

Refrigerant Oil (Charged) cm

3

- RB68A or Freol Alpha68M

Refrigerant (Charged) R410A kg (oz) - 0.78 (27.5)

Height mm (inch) 250 (9-27/32) 540 (21-1/4)

Width mm (inch) 770 (30-5/16) 780 (30-23/32)

Dimension

Depth mm (inch) 205 (8-1/16) 289 (11-3/8)

Net Weight kg (lbs) 7.0 28 (62)

Gas mm (inch) 9.52 (3/8) Pipe

Diameter

Liquid mm (inch) 6.35 (1/4)

Pipe Length m (ft) 3 (9.8) - 15(49.2)

Height Difference m (ft) 5 (16.4)

Additional Gas Amount g/m (oz/ft) 20 (0.2)

Refrigerant Charge Less m (ft) 7.5 (24.6)

Inner diameter mm 14 - Drain Hose

Length mm 500 -

Type - Rotary

Motor Type - Induction (6-poles)

Compressor

Rated Output W - 750

Type Cross-Flow Fan Propeller Fan

Material AS PP

Motor Type Induction (8-poles) Induction (6-poles)

Input power W - -

Output power W 30 15

Lo rpm 830 -

Me rpm 1070 -

Fan

Speed

Hi rpm 1360 750

Fin material Aluminium (Pre Coated) Aluminum ( Pre Coated)

Fin type Slit Fin Slit Fin

Row x stage x FPI 2 x 12 x 18 1 x 24 x 17

Heat

Exchanger

Size (W x H x L) mm 610 x 315 x 25.4 709 x 504 x 18.2

Material P.P.HONEY COMB - Air Filter

Type

Style One-Touch -

1. Cooling capacities are based on indoor temperature of 27°C Dry Bulb (80.6°F Dry Bulb), 19°C Wet Bulb (66.2°F

Wet Bulb) and outdoor air temperature of 35°C Dry Bulb (95.0°F Dry Bulb), 24°C Wet Bulb (75.2°F Wet Bulb).

2. Heating capacities are based on indoor temperature of 20°C Dry Bulb (80.6°F Dry Bulb) and outdoor air

temperature of 7°C Dry Bulb (44.6°F Dry Bulb), 6°C Wet Bulb (42.8°F Wet Bulb).

6

Item Unit

φ

Single

V 230

Power Source (Phase, Voltage, Cycle)

Hz 50

Input Power COOLING W 750(190~1000)

HEATING W 900(220~1200)

Starting Current A 4.10

Running Current COOLING A 3.60

HEATING A 4.10

Maximum Current A 5.50

Power Factor COOLING % 90

HEATING % 95

Power factor means total figure of compressor, indoor fan motor and outdoor fan motor.

Number of core 3 (1.5mm) Power Cord

Length m 1.3

Thermostat Electronic Control

Protection Device Electronic Control

Note

z Specification is subject to change without prior notice for further improvement.

z Operational temperature range:

Indoor Outdoor

Temperature °C

* DBT *WBT *DBT *WBT

Maximum 32 23 43 26

COOLING

Minimum 16 11 16 11

Maximum 30 - 24 18

HEATING

Minimum 16 - -5 -6

NOTICE: This model is not suitable for 24 hours non-stopping operation in heating mode below -5°C. If this model

is used out of above conditions, the outdoor unit might be frozen up and stop operation for protection

control.

*DBT: Dry bulb temperature

*WBT: Wet bulb temperature

7

2.2 CS-UE12JKE CU-UE12JKE

Item Unit Indoor Unit Outdoor Unit

kW 3.50(0.90~3.90) Capacity

BTU/h 11940(3070~13300)

W/W 3.30(5.29~3.25) EER

BTU/hW 11.26(18.06~11.08)

dB(A) Hi: 42 Lo: 30 QLo: 22 Hi: 48

COOLING

Noise Level

Power level dB Hi: 53 Lo: - Hi: 61

kW 4.25(0.90~4.70) Capacity

BTU/h 14490(3070~16030)

W/W 3.63(6.00~3.56) COP

BTU/hW 12.38(20.47~12.14)

dB(A) Hi: 42 Lo: 33 QLo: 25 Hi: 50

HEATING

Noise Level

Power level dB Hi: 53 Lo: - Hi: 63

l/h 2.0 Moisture Removal

(pt/h) 3.5

Lo m

3

/m (ft

3

/m) 8.1(285) -

Me m

3

/m (ft

3

/m) 9.9(349) -

Air Volume

Hi m

3

/m (ft

3

/m) 11.7 (413) 30.5 (1076)

Refrigerant Control Device - Capillary Tube

Refrigerant Oil (Charged) cm

3

- RB68A or Freol Alpha68M

Refrigerant (Charged) R410A kg (oz) - 0.97 (34.2)

Height mm (inch) 280 (11-1/32) 540 (21-1/4)

Width mm (inch) 799 (31-15/32) 780(30-23/32)

Dimension

Depth mm (inch) 183 (7-13/64) 289 (11-3/8)

Net Weight kg (lbs) 8.5 (19) 30 (66)

Gas mm (inch) 9.52 (3/8) Pipe

Diameter

Liquid mm (inch) 6.35 (1/4)

Pipe Length m (ft) 3 (9.8) - 15 (49.2)

Height Difference m (ft) 5 (16.4)

Additional Gas Amount g/m (oz/ft) 20 (0.2)

Refrigerant Charge Less m (ft) 7.5 (24.6)

Inner diameter mm 14 - Drain Hose

Length mm 500 -

Type - Rotary

Motor Type - Induction (6-poles)

Compressor

Rated Output W - 900

Type Cross-Flow Fan Propeller Fan

Material AS PP

Motor Type Induction (8-poles) Induction (6-poles)

Input power W - -

Output power W 30 25

Lo (Cool) rpm 940 -

Me (Cool) rpm 1160 -

Fan

Speed

Hi (Cool) rpm 1370 870

Fin material Aluminum (Pre Coated) Aluminum (Pre Coated)

Fin type Slit Fin Slit Fin

Row x stage x FPI 2 x 15 x 20 2 x 24 x 17

Heat

Exchanger

Size (W x H x L) mm 610 x 315 x 25.4 709 x 540 x 36.4

Material P.P.HONEY.COMP - Air Filter

Type

Style One-Touch -

1. Cooling capacities are based on indoor temperature of 27°C Dry Bulb (80.6°F Dry Bulb), 19°C Wet Bulb (66.2°F

Wet Bulb) and outdoor air temperature of 35°C Dry Bulb (95.0°F Dry Bulb), 24°C Wet Bulb (75.2°F Wet Bulb).

2. Heating capacities are based on indoor temperature of 20°C Dry Bulb (80.6°F Dry Bulb) and outdoor air

temperature of 7°C Dry Bulb (44.6°F Dry Bulb), 6°C Wet Bulb (42.8°F Wet Bulb).

8

Item Unit

Single

V 230

Power Source (Phase, Voltage,

Cycle)

Hz 50

Input Power COOLING W 1060(170~1200)

HEATING W 1170(150~1320)

Starting Current A 5.20

Running Current COOLING A 4.70

HEATING A 5.20

Maximum Current A 6.80

Power Factor COOLING 98

HEATING % 98

Power factor means total figure of compressor, indoor fan motor and outdoor fan motor.

Number of core

3 (1.5mm)

Power Cord

Length m

1.3

Thermostat

Electronic Control

Protection Device

Electronic Control

Note

z Specification is subject to change without prior notice for further improvement.

z Operational temperature range:

Indoor Outdoor

Temperature °C

* DBT *WBT *DBT *WBT

Maximum 32 23 43 26

COOLING

Minimum 16 11 16 11

Maximum 30 - 24 18

HEATING

Minimum 16 - -5 -6

NOTICE: This model is not suitable for 24 hours non-stopping operation in heating mode below -5°C. If this model

is used out of above conditions, the outdoor unit might be frozen up and stop operation for protection

control.

*DBT: Dry bulb temperature

*WBT: Wet bulb temperature

9

3. Features

• Inverter Technology

o Wider output power range

o Energy saving

o Quick Cooling

o More precise temperature control

• Long Installation Piping

o CS/CU-UE9/12JKE, long piping up to 15 meters.

• Easy to use remote control

• Quality Improvement

o Random auto restart after power failure for safety restart operation

o Gas leakage protection

o Prevent compressor reverse cycle

o Inner protector to protect compressor

• Operation Improvement

o Quiet mode to reduce the indoor unit operating sound

o Powerful mode to reach the desired room temperature quickly

o 12-hour timer

• Serviceability Improvement

o Breakdown Self Diagnosis Function.

10

4. Location of Controls and Components

Indoor Unit

4.1 Outdoor Unit

4.2 Remote Control

z For normal operation, the ERROR RESET button is

not in use.

z Press RESET button to restore the remote control’s

default setting.

OFF/ON

Operation

mode

Airflow direction

adjustment

Timer

setting

Temperature

setting

Transmitter

Fan speed

selection

11

5. Dimensions

5.1 Indoor Unit

Unit：mm

CS-UE9JKE

12

CS-UE12JKE

13

5.2 Outdoor Unit

Unit: mm

14

6. Refrigeration Cycle Diagram

15

7. Block Diagram

16

8. Wiring Diagram

CS/CU-UE9JKE

17

CS/CU-UE12JKE

18

9. Installation Instruction

9.1 Select the Best Location

9.1.1 Indoor Unit

• There should not be any heat source or steam near the

unit.

• There should not be any obstacles blocking the air

circulation.

• A place where air circulation in the room is good.

• A place where drainage can be easily done.

• A place where noise prevention is taken into consideration.

• Do not install the unit near the door way.

• Ensure the spaces indicated by arrows from the wall, ceiling,

fence or other obstacles.

• Recommended installation height for indoor unit shall be at

least 2.5m.

9.1.2 Outdoor Unit

• If an awning is built over the unit to prevent direct sunlight or

rain, be careful that heat radiation from the condenser is not

obstructed.

• There should not be any animal or plant which could be

affected by hot air discharged.

• Keep the spaces indicated by arrows from wall, ceiling,

fence or other obstacles.

• Do not place any obstacles which may cause a short circuit

of the discharged air.

• If piping length is over the rated length, additional refrigerant

should be added as shown in the table below:

Example: If the unit is installed at a 10m distance, the quantity

of additional refrigerant should be 50 g.

…… (10-7.5) m x 20g/m = 50 g

Piping size Model

Gas Liquid

Rated

Length

(m)

Max

Elevati

on (m)

Min

Piping

Length

(m)

Max

Piping

Length

(m)

Additional

Refrigera

nt (g/m)

UE9JKE 3/8” 1/4" 7.5 5 3 15 20

UE12JKE 3/8” 1/4” 7.5 5 3 15 20

11.1.3

Indoor/Outdoor Unit

19

Wall

Indoor Outdoor

15 mm

Sleeve for

tube ass’y

Approx. 5 - 7 mm

Bushing for tube ass’y

Putty or caulking compound

Ø 70 through hole

9.2 Indoor Unit

9.2.1 How to Fix Installation Plate

The centre of installation plate should be at more than 450mm at right and left of the wall.

The distance from installation plate edge to ceiling should be more than 67mm.

From installation plate left edge to unit's left side is 62mm (UE9JKE) or 98mm (UE12JKE).

From installation plate right edge to unit's right is 79mm (UE9JKE) or 112mm (UE12JKE).

○

B : For left side piping, piping connection for liquid should be about 10 mm from this line.

: For left side piping, piping connection for gas should be about 45mm from this line.

: For left side piping, piping connecting cable should be about 785mm (UE9JKE) or 800mm (UE12JKE) from

this line.

1 Mount the installation plate on the wall with 5 screws or more. (If mounting the unit on the wall, consider

using anchor bolts.) Always mount the installation plate horizontally by aligning the marking-off line with

the thread and using a level gauge.

2 Drill the piping plate hole with ø70 mm hole-core drill.

z Put measuring tape at position as shown in the diagram above. The hole centre is

obtained by measuring the distance namely 105mm and 145mm for left and right hole

respectively (UE9JKE), or 150mm and 125mm for (UE12JKE).

z Drill the piping plate hole at either the right or left and the hole should be slightly slanted

to the outdoor side.

9.2.2 To Drill a Hole in the Wall and Install a Sleeve of Piping

1 Insert the piping sleeve to the hole.

2 Fix the busing to the sleeve.

3 Cut the sleeve until it extrudes about 15mm from the wall

4 Finish by sealing the sleeve with putty or caulking compound at the

final stage.

Caution

When the wall is hollow, please be sure to use the sleeve for tube

ass’y to prevent dangers caused by mice biting the connecting

cable.

20

9.2.3 Indoor Unit Installation

Page is loading ...

Panasonic CS-UE12JKE Datasheet

This manual is also suitable for

Panasonic CS-UE12JKE Datasheet

Related papers

Other documents