Axxera AXA10D Owner's manual

Category
Audio amplifiers
Type
Owner's manual

This manual is also suitable for

INSTALLATION / OWNER'S MANUAL
Mobile Power Amplifiers
AXA SERIES
AXA10D
AXA20
AXA40D
2
INSTALLATION
Preparation
Please read entire manual before installation. Due to the technical nature of amplifiers, it
is highly recommended that your Axxera amplifier is installed by a professional installer or
an authorized dealer.
Before You Start
•Disconnectnegativebatteryterminal.(consultaqualifiedtechnicianforinstructions)
•Avoidinstallingtheamplifierwhereitwouldbesubjecttohightemperatures,suchas
fromdirectsunlight,orwhereitwouldbesubjecttodust,dirtorexcessivevibration.
•Useextremecautionwhendrillingholestoavoiddamagingfuellinesorexistingvehicle
wiring.
•Allamplifierinstallationsrequirepower,signalandspeakerwires(notincluded).
•Anamplifierinstallationkit(soldseparately)ishighlyrecommendedtofacilitatethe
installation. Consult your dealer for recommendations.
Mounting Location
•Chooseamountinglocationfortheamplifier.Suggestedlocationsincludeunderaseat
orinthetrunk.
•Theamplifiercanbemountedhorizontal(recommended)orvertical.Foroptimum
performance,makesuretoprovideatleast1"ofspacearoundallsides.Donotmount
theamplifierundercarpetsorwhereairflowisrestricted.
•Donotinstalltheamplifierwhereitmaybeexposedtomoisture.
•Theoptimummountinglocationvariesbetweenvehicles.Remembertotestallamplifier
functions before completing the final mounting procedure.
TYPICAL MOUNTING METHOD
NOTE:
Be sure to follow specific instructions included with your amplifier installation
kit (not included with this amplifier). The information below should be used as a
general guideline only.
Power Wire (+12V)
•Disconnectnegativebatteryterminalbeforeproceeding.Consultaqualified
technician for instructions if you are unsure.
•Planwireroutingbeforecuttinganywirestolength.Beginbyroutingthepower
+12Vwirefromthebatterytotheamplifierlocation.Useagrommetwhenrunning
wiresthroughthefirewallormetalopenings.Avoidrunningthepowerwirenear
existingvehiclewiringtopreventinducednoisefromenteringtheaudiosystem.
•Useextremecautionwhendrillingholestoavoiddamagingfuellinesorexisting
vehiclewiring.
•The+12VwireMUSTbefusedwithin18"ofthebatteryforprotectionofthevehicle’s
electrical system.
Ground Wire (GND)
•Theamplifiergroundwireshouldbeasshortaspossible.Chooseacleanunpainted
sectionofmetalorthevehiclechassiswhenattachingthegroundconnection.Be
sure to clean the area of any dirt or grease.
Remote Turn-on Wire (REM)
•Theremoteturn-onwireconnectstotheheadunit'samplifierturn-onleadorpower
antenna output.
Speaker Wires
•Chooseadequategaugespeakerwiredependingonyourexactamplifier/speaker
combination.Besuretoobservepolaritywhenconnecting.
•Donotgroundanyspeakerwiresorconnectanyspeakerwirestogether.
Input Signal
•Theamplifier'sinputsignalconnectstotheheadunit'slowlevel(RCA)orhighlevel
(speakerwire)outputs.
•Lowlevelinputsignalsdeliverthebestperformance.Ifunavailable,usethehighlevel
inputs-wheninterfacingwithfactoryheadunitforinstance.
CAUTION
•Donotusebothlowandhighlevelinputsatthesametime-connectonlyoneorthe
other.
•Neverrunanywiresunderneathoroutsidethevehicle.
3
Connection Descriptions
INSTALLATION
4
Audio Inputs and Controls
HighLevelInputs
RCALineInputs
Gain
SubsonicFilter
BassBoost
LowPassFilter
1
2
3
RemoteBassControlInput
CrossoverMode
CrossoverFrequencyControl
PassThrough
PowerandProtectionLEDs
2 41
10 9
28
3
4
5
7
8
9
10
356
11
1
AXA10D
AXA20
AXA40D
7
6 5 11
82
12
9
318 3
9
6
INSTALLATION
Power and Speaker Connections
SpeakerConnections
Fuse(s)
+12VDCBatteryConnection
1
2
3
RemoteTurnOn
Ground Connection
RemoteTurnOnOutput
4
5
5
54
1
5
2
14
21
2
AXA10D
AXA20
AXA40D
5 3
INSTALLATION
3
3
6
6
4
6
REM (Remote Turn On)
SPEAKERS
RCA CABLES
GROUND
FUSE
12V BATTERY
MAXIMUM
12V DC
(Power)
Fuse Rating
Whenreplacingfuses,makesurenewfuse
isthecorrecttypeandamperage.Usingan
incorrect fuse could damage the amplifier.
AXA10D25ampATOx2
AXA2030ampATOx1
AXA40D40ampATOx1
Power/Ground Wire Size
Foroptimumperformance,useonlythewire
sizelistedbeloworlarger.Makesuretouse
thesamesizepowerandgroundwire.
AXA10D4awg
AXA208awg
AXA40D4awg
Main Power Connections
Connect+12V,GNDandREMwiresaccordingly.AsuitablefuseMUSTbeinstalledon
the+12Vleadwithin18"ofthebatteryforprotectionofthevehicle’selectricalsystem.
Typical Wire Routing
INSTALLATION
High-Level Input
(speaker cables)
Low-Level Input
(RCA)
7
Amplifier Connections
Speaker Connections
Connectspeakerwiresobserving
polarity. Theminimumimpedance
load for the AXA20 and AXA40D
is 2 ohms stereo and 4 ohms
bridged.Useofloadslowerthan
these is not recommended and
maycauseamplifierdamage.The
AXA20andAXA40Dcanbewired
forstereo,bridgedorstereo/
bridged simultaneous operation.
Input Signal Connections
Low Level Input (RCA)
Lowlevel(RCA)inputsignalispreferredforbestperformance.Typicaltrunk-mount
amplifierinstallationsrequirea17-20footRCAcable.Mosttrucksandunder-seat
applicationsrequirea6-9footRCAcable.UsingtwistedpairconstructionRCAcableswill
minimize noise.
High Level Input (Speaker Wire)
Highlevelinputsshouldonlybeused
whenRCAoutputsarenotavailable
from the head unit. Connect the
headunitspeakeroutputsto
thehighlevelinputconnector
asshownbelow.Theblackwire
(signalreferenceground)mayor
maynotrequireaconnectionto
chassisground-dependingonyour
particular installation.
Subwoofer (mono)
Typical Bridged Wiring
(4 ohms minimum)
2 Speakers (stereo)
Typical Stereo Wiring
(2 ohms minimum)
CAUTION
Donotusebothlowandhighlevelinputsatthe
sametime-connectonlyoneortheother.
AXA20speakerconnectionsshown
INSTALLATION
8
Configuration/Setup
Theinputlevelcontrol(gain)isusedtoobtainthebest
possiblematchbetweentheheadunitaudiooutputandthe
amplifierinput.Beginbyturningtheinputlevelcontrolfully
counterclockwise.Next,turnuptheheadunitvolumecontrol
around3/4ofthewayup.Adjusttheinputlevelcontrol
clockwiseuntilaudibledistortionisheard,thenslightly
counterclockwisetoprovidethebestmatch.
Repeatforallinputlevelcontrols.
Thecrossoverisusedtofilteroutfrequenciesaboveor
belowacertainpoint.ChooseLPFwhenusingtheamplifier
withsubwoofers,HPFwhenusingwithmidrange/tweeter
combinations and FLATwhenusingwithcoaxial-type
speakers.
Note: Choose FLATwhenusingtheamplifierinstereo/
bridgedsimultaneousmode.Inthismode,passive
crossoversarerequired.Failuretousethecorrectpassive
componentsmaydamagetheamplifierand/orspeakers.
Consultaqualifiedprofessionalforrecommendations.
Thiscontrolallowspreciseadjustmentofthecrossover
frequency.
Thiscontrolprovidesadditionalboost@45Hzwhenused
withsubwoofers.Adjustthiscontrolwithcaution-as
improperusecandamagespeakers!
Settingthiscontroltothedesiredfrequencywilllimit
harmfulfrequenciesbelowthesettingfromgoingtothe
subwoofer(s),preventingpossibledamagefromfrequencies
thatsubwoofersarenotdesignedtohandle.
ThegreenLEDindicatorilluminatesduringnormaloperation
(POWER)andtheredLEDindicatorisvisiblewhenthe
amplifierdetectsafault(PROTECT).
Input level Control
Crossover Mode
Crossover Frequency
Control
Bass Boost
Subsonic Filter
(AXA10D)
LED Indicators
OPERATION
9
Troubleshooting
Problem Cause Action
Unit will not turn on
(no power LED
indicator)
+12Vwirenotconnectedorincorrect
voltage
REMwirenotconnectedorincorrectvoltage
Checkconnectionsforpropervoltage
(11~16VDC)
GNDwirenotconnected Checkconnectiontoground
Fuse(s)blown Replacefuse(s)
Unit has power - LED is
green (but no sound)
Speakerwiresnotconnected Checkconnectionsatspeakers
Volumeturnedallthewaydown Increasevolumelevelatheadunit
Oneormorespeakerwirestouchingeach
other or touching chassis ground
Insulateallbarespeakerwiresfromeach
other and chassis ground
Speaker(s)defectiveordamaged Check/replacespeaker(s)
Inputsignalnotconnected Checkhighorlowlevelinputsforproper
connection
Unit blows fuse(s)
Incorrectfuserating Usefuse(s)withcorrectrating
+12Vwiretouchingchassisground Checkforpinchedwire
Speaker(s)defectiveordamaged Check/replacespeaker(s)
Engine noise
Badgroundconnection Makesureamplifierisgroundedtoclean
bare metal
SignalgroundlooporRFI(radiofrequency
interference)
Re-routeRCAcablesfromexistinghigh
currentwiring
LED illuminates red
(protect mode)
Oneormorespeakerwirestouchingeach
other or touching chassis ground
Insulateallbarespeakerwiresfromeach
other and chassis ground
Speaker(s)defectiveor
damagedinternally(shorted) Check/replacespeaker(s)
Speakerloadlessthan2ohms(stereo)
Speakerloadlessthan4ohms(bridged)
Adjustspeakerload-amplifierwillnot
operateatlessthan4ohmswhenbridged
Distorted audio output Incorrectinputsignaltypeor
inputleveltoohigh
Checkconnectionsandreduce/adjust
inputlevel
Low audio output Incorrectinputsignaltypeor
inputleveltoolow
Checkconnectionsandincrease/adjust
inputlevel
Weak bass Speaker(s)arewiredoutofphase Check(+)and(-)speakerconnections
(Observecorrectpolarity)
OPERATION
10
Specifications
CEA-2006PowerStandardSpecifications
(reference: 14.4VDC, 20Hz~20kHz)
PowerOutput(14.4VDC,20Hz~20kHz):
350 Watts x 1 channel @ 4 ohms and 1% THD+N
650 Watts x 1 channel @ 2 ohms and 1% THD+N
Peak Music Power Output: 1750 Watts
Signal to noise ratio: 70dBA (reference: 1 watt into 4 ohms)
Frequency response: 20Hz - 150Hz
Amplifier dimensions: 1.58" x 4.7" x 9"
CEA-2006PowerStandardSpecifications
(reference: 14.4VDC, 20Hz~20kHz)
PowerOutput(14.4VDC,20Hz~20kHz):
90 Watts x 2 channels @ 4 ohms and 1% THD+N
120 Watts x 2 channels @ 2 ohms and ≤ 1% THD+N
280 Watts x 2 channels @ 4 ohms (bridged) and 1% THD+N
Peak Music Power Output: 900 Watts @ 4 ohms
Signal to noise ratio: 90dBA (reference: 1 watt into 4 ohms)
Frequency response: 10Hz - 35kHz
Amplifier dimensions: 2.1" x 9.7" x 9"
CEA-2006PowerStandardSpecifications
(reference: 14.4VDC, 20Hz~20kHz)
PowerOutput(14.4VDC,20Hz~20kHz):
100 Watts x 4 channels @ 4 ohms and 1% THD+N
150 Watts x 4 channels @ 2 ohms and ≤ 1% THD+N
260 Watts x 2 channels @ 4 ohms (bridged) and 1% THD+N
Peak Music Power Output: 2000 Watts @ 4 ohms
Signal to noise ratio: 70dBA (reference: 1 watt into 4 ohms)
Frequency response: 10Hz - 35kHz
Amplifier dimensions: 1.58" x 4.7" x 9"
AXA10D
AXA20
AXA40D
OPERATION
11
Limited One-Year Warranty
Thiswarrantygivesyouspecificlegalrights.
Youmayalsohaveotherrightswhichvary
from state to state.
DualElectronicsCorp.warrantsthis
product to the original purchaser to
be free from defects in material and
workmanshipforaperiodofoneyearfrom
the date of the original purchase.
DualElectronicsCorp.agrees,atour
option,duringthewarrantyperiod,
to repair any defect in material or
workmanshiportofurnishanequal
new,renewedorcomparableproduct
(whicheverisdeemednecessary)in
exchangewithoutcharges,subjectto
verificationofthedefectormalfunctionand
proofofthedateofpurchase.Subsequent
replacementproductsarewarrantedfor
thebalanceoftheoriginalwarrantyperiod.
Who is covered?Thiswarrantyis
extended to the original retail purchaser
for products purchased from an authorized
DualdealerandusedintheU.S.A.
What is covered?Thiswarrantycovers
alldefectsinmaterialandworkmanshipin
thisproduct.Thefollowingarenotcovered:
software,installation/removalcosts,
damage resulting from accident, misuse,
abuse, neglect, product modification,
improperinstallation,incorrectlinevoltage,
unauthorizedrepairorfailuretofollow
instructionssuppliedwiththeproduct,or
damage occurring during return shipment
oftheproduct.Specificlicenseconditions
andcopyrightnoticesforthesoftwarecan
befoundviawww.dualav.com.
What to do?
1.Beforeyoucallforservice,checkthe
troubleshootingguideinyourowner’s
manual.Aslightadjustmentofany
customcontrolsmaysaveyouaservice
call.
2.Ifyourequireserviceduringthe
warrantyperiod,youmustcarefully
packtheproduct(preferablyinthe
originalpackage)andshipitbyprepaid
transportationwithacopyoftheoriginal
receipt from the retailer to an
authorizedservicecenter.
3. Please describe your problem in
writingandincludeyourname,areturn
UPSshippingaddress(P.O.Boxnot
acceptable),andadaytimephone
numberwithyourshipment.
4.Formoreinformationandforthe
location of the nearest authorized
servicecenterpleasecontactusbyone
ofthefollowingmethods:
•Callustoll-freeat1-866-382-5476
•E-mailusatcs@dualav.com
ExclusionofCertainDamages:This
warrantyisexclusiveandinlieuofany
andallotherwarranties,eAXAessedor
implied,includingwithoutlimitationthe
impliedwarrantiesofmerchantabilityand
fitness for a particular purpose and any
obligation, liability, right, claim or remedy
incontractortort,whetherornotarising
fromthecompany’snegligence,actualor
imputed.Nopersonorrepresentativeis
authorized to assume for the company
anyotherliabilityinconnectionwiththe
saleofthisproduct.Innoeventshallthe
company be liable for indirect, incidental or
consequentialdamages.
WARRANTY
DualElectronicsCorp.
TollFree:1-866-382-5476
www.axxeraaudio.com
©2013DualElectronicsCorp.
NSA0113-V01
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12

Axxera AXA10D Owner's manual

Category
Audio amplifiers
Type
Owner's manual
This manual is also suitable for

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI