JILONG JL29P423NG User manual

Brand: JILONG

Model: JL29P423NG

Type: User manual

2014

INFLATABLE’S EXPERT

SFP3-14-GB

SAND FILTER PUMP MANUAL

2SFP3-14-GBwww.jilong.com

Specications

Model JL29P423NG

Voltage 220-240 V

Power 65 W

Max. operation pressure 1bar (15psi)

Effective lter area 0.05m² (0.57ft²)

Max. water ow rate 800 gal/h (3000L/h)

Rated lter ow rate 530 gal/h（2000L/h）

Max. water temperature 35℃

Recommended lter medium 20# quartz sand or glass sand

Particle size: 0.45-1.25mm

Recommended medium amount 9Kg of quartz sand or glass sand

Please read the following instructions carefully and

keep them for future reference.

Safety Instructions

Basic safety precautions for installing and using the product should comply

with the following.

1.Warning: To reduce risk of injury, do not allow children to use the

product. Children and the disabled must be supervised closely at all times.

2.Warning: Keep children away from the product and wires.

3.Warning: Children must be carefully supervised to ensure they cannot

access the 4.product.

5.Warning: The product must be kept away from the pool to avoid children

climbing on it.

6.Warning: To avoid the risk of electric shock, connect the product with

a grounded receptacle protected by electrical leakage. If you are unable

to confirm, please contact an experienced electrician for installation.

Maximum leakage current is 30mA, so please do not use a movable

receptacle.

7.Warning: Always unplug the product from the electrical outlet before

removing, cleaning, servicing or making any adjustment to the product.

8.Warning: Do not bury the power cord. Place the cord where it cannot be

damaged by a lawn mower or other equipment.

9.Warning: Do not use the product if the power cord is damaged.

10.Warning: To reduce the risk of electric shock, do not connect the

extension cord, timer, adapter or converter plug to the lter body. Please

provide a permanently installed receptacle.

11.Warning: Do not attempt to unplug the product with wet hands or while

standing in water.

12. Attention: After assembly, the plug shall be placed in such a way that it

is easily visible and accessible to the user.

2014

3SFP3-14-GBwww.jilong.com

13. Attention: Always keep the product at least 2m away from the pool.

14. Attention: Always keep the plug at least 3.5m away from the pool.

15.Warning: Never start the product while the pool is in use.

16.Warning: Adult assembly and operation are required.

17.Warning: This product is designed for use with movable pools only. It

must not be used with permanently installed pools. A movable pool is a

device that can be easily assembled & disassembled for water storage.

18.Warning: To prevent the product from any damage, please turn it off

before turning the control valve.

19.Warning: To reduce the risk of being sucked into ot towards the pump

never enter the water when the lter hood is loose, damaged, destroyed

or lost. Please replace the filter hood immediately if any of the above

situations pertain.

20.Warning: Do not play or swim near the filter hood. Your body or

hair may be caught in the pump which can lead to permanent injury or

drowning.

21.Warning: Do not start the product when the data displayed on the

manometer on its body exceeds the maximum value specied.

22. Warning:The maximum total head, 1.5 in metres (for pumps having a

rated power input exceeding 50 W)

23. Warning:The pump is to be supplied by an isolating transformer or

supplied through a residual current device (RCD) having a rated residual

operating current not exceeding 30 mA.

24. Warning:The supply cord cannot be replaced. If the cord is damaged

the appliance should be scrapped.

25. Warning:This appliance can be used by children aged from 8 years

and above and persons with reduced physical, sensory or mental

capabilities or lack of experience and knowledge if they have been given

supervision or instruction concerning use of the appliance in a safe way

and understand the hazards involved. Children shall not play with the

appliance. Cleaning and user maintenance shall not be made by children

without supervision.

26. Attention: The product is intended for use for those purposes detailed

in the manual only.

This marking indicates that this product should not be disposed

with other household wastes throughout the EU. To prevent

possible harm to the environment or human health from

uncontrolled waste disposal, recycle it responsibly to promote

the sustainable reuse of material resources. To return your

used device, please use the return and collection systems or contact the

retailer where the product was purchased. They can take this product for

environmental safe recycling.

WEEE

Correct Disposal of this product

4SFP3-14-GBwww.jilong.com

Read Important Safety Instructions and Follow all Safety Cautions

Parts List FIG. 01

FIG. 02

No. Name Quantity No. Name Quantity

P1 Manometer 1 P2 Control

valve 1

P3 Drain nut 1 P4 Adapter 2

P5 Seal ring of

control valve 1 P6 Control

valve

retainer

P7 Control

valve screw 2P8 Body 1

P9 Central

connecting

pipe

1 P10 Pedestal 1

P11 Drain valve 1 P12 Connecting

pipe 1

P13 Slag

blocking

screen

1 P14 Seal ring

of slag

blocking

barrel

P15 Cover of

slag blocking

barrel

1 P16 Positioning

plate 1

P17 Strap 6 P18 Water pipe 2

Installation Instructions

Tools required: 1 Phillips screwdriver

Product installation position and assembly:

· The product must be installed on rm and level ground.

· Provide sufcient space and light for the convenience of

daily maintenance.

· The motor must be ventilated for cooling. Do not put the

product in a wet place with no ventilation.

At least 2 persons are recommended to install the product.

1. Position the product in the place selected.

2. Make sure the connection between the body and the

pedestal is good.

Important note: the product must be positioned on the ground

or a permanently upward pedestal in some EU countries. To determine whether there

are any regulations on surface pool lters consult the local authorities. If any, x the

lter using two holes drilled in a platform. (See FIG. 02)

The sand lter pump should be secured on a cement pedestal or wood platform to

avoid it tipping over.

Note: the hole diameter of the pedestal is 6.4mm.

Note: the maximum diameter of the two screws and lock nuts used is 6.4mm.

2014

5SFP3-14-GBwww.jilong.com

I. Sand Filling

Note: use 20# quartz sand or glass sand. Particle size of the sand is 0.45-

1.25mm.

Note: before sand filling, make sure the central connecting pipe (P9) is

connected at the bottom of the body and vertically stands in the center of

the body (see FIG. 03).

1.First, sleeve the positioning plate (P16) onto the top of the central

connecting pipe. (See FIG. 04)

2.Then pour sand into the body slowly. (See FIG. 05)

3. When the sand is near to the half way level, remove the positioning plate,

spread the sand evenly with one’s hands, and pour in more sand so that

the lling of the remaining sand is buffered. This can help avoid excessive

vibrations of the central connecting pipe (P9). Afterwards, ensure the

positioning plate (P16) replaced properly and keep pouring sand.

4. Remove the positioning plate (P16) (see FIG. 06) and spread the sand

evenly with one’s hands

5.Clear away the sand around the top of the body.

FIG. 03

FIG. 06

FIG. 04

FIG. 07

FIG. 05

FIG. 08

6SFP3-14-GBwww.jilong.com

II. Installation of manometer

III. Installation of control valve

1. Take out the manometer from the package,

check whether that the seal ring is present.

2. Screw the manometer onto the control

valve in a clockwise direction until tightly xed.

1. Connect one end of a corrugated pipe (P18) to Port B, the other end to

port F of the pool. Secure tightly with a strap (P17).

2. Connect one end of the connecting pipe P12 to Port C of the control

valve, the other end to Port C of the motor. Secure tightly with the strap

1.Check whether the seal ring of the control valve (P5) is properly

positioned, then place the control valve (P2) onto the top of the body

slowly, and ensure the port at the bottom of the control valve is closely

inserted into the port on the top of the central connecting pipe (P9) (FIG.

06, 07).

2. There are 3 port connecting points on the control valve. It is essential to

ensure Port A points towards the pool, and that Port C of the control valve

is aligned with Port C of the motor. (See FIG. 10)

3. Remove the screw group on the control valve retainer, clamp the control

valve retainer around the ange between the body and the control valve,

and then pass the screw group through the drilled clip nuts and tighten

with a screwdriver (not provided) (see FIG. 08).

FIG. 09

FIG. 10

2014

7SFP3-14-GBwww.jilong.com

I. Location and functions of the control valvecontrol valve

Instructions for use

(P17).

3. Connect one end of the other corrugated pipe (P18) to Port A of the

control valve, the other end to Port E of the pool. Secure tightly with the

strap (P17).

4. Check to confirm whether the installation is finished properly,

afterwards use the sand lter pump to lter the pool water.

Signs Location

of control

valve

Functions Water ow direction

Filter Normal ltering to rinse

the pool Water flows through the

lter bed where the sand

filter pump lies and then

enters the pool

Backwash Reverse-direction water

flow to rinse the filter

bed

Water flows through the

lter bed where the sand

filter pump lies and is

then directly discharged

from the drain outlet.

Rinse This function is used

for rst startup. Sand in

the sand tank is rinsed

and the sand bed after

backwashing is leveled.

Water flows through the

lter bed where the sand

filter pump lies and is

then directly discharged

from the drain outlet.

Drain Discharged directly

from the drain outlet,

used to lower water

level or discharge water

from the pool

Discharged directly from

the drain outlet of the

sand filter pump without

passing through the filter

bed

Circulation Circulates pool water

without passing through

the lter bed.

Water flows directly

into the pool through

the control valve of the

sand filter pump without

passing through the filter

bed

Closed Closed water flow

between the filter and

the pool

8SFP3-14-GBwww.jilong.com

II. Operation of the control valve

III. Draining procedure

Warning: Before operation, make sure all corrugated

tubes are properly connected and locked and the lter

has been lled with the correct amount of sand.

Warning: Before operation, make sure the product is

disconnected from the grounded receptacle protected

by electrical leakage.

Warning: The control valve is provided with one closed

valve position. Do not attempt to start the product when

the control valve is in the closed position.

1.Make sure the product is powered-

off.

2.Remove the drain nuts (P3) first,

then move the adapter (P4) at Port A

and water pipe (P18) to Port D (see

FIG. 12).

3.Press the control valve handle

downwards and rotate it to the draining

position, and then turn the power

1.After the aforementioned preparations, the sand

lter pump is ready for use. Set the lter function of

the control valve.

2.Insert the plug into the matched receptacle to run

the sand lter pump.

Note: During the operation of the sand filter pump,

check the pressure reading of the manometer (P1).

Generally, when the pressure of the recommended

1.When rotating the control valve, press the control valve

handle rst, then rotate the handle to the required position (see FIG. 11).

FIG. 12

FIG. 14

on. Perform draining until clean water is discharged (see FIG. 12). After

draining, disconnect the power.

4.Rotate the control valve handle to backwashing position. Power on again,

until clean water ows, then backwashing nishes. Disconnect power (see

FIG. 12).

5.Remove the adapter (P4) at Port D and water pipe (P18) and return them

to Port A (see FIG. 10).

6. Return the drain nut (P3) to Port D (see FIG. 10).

7.Power on and select the required function position. Begin operation.

Note: this step is for rst operation only.

Note: do not attempt to set between two functions of the control valve to

avoid possible leakage.

2014

9SFP3-14-GBwww.jilong.com

V. Sand Filter Pump Maintenance

VI. Motor and Slag Blocking Barrel Cleaning and Maintenance

Note: You must make sure that maintenance begins

only after the sand filter pump is unplugged.

Otherwise serious risks such as personal injury and

even death may occur.

Note: Record the reading of the manometer during

the operation of the sand lt er pump (see FIG. 15).

When the manometer shows a pressure of 0.2bar

(3psi) or higher, please clean up the sand bend

or replace the sand. Use "backwash" and "rinse"

functions.

Note: regular rinsing according to use situation is

recommended.

1.It is essential to make sure the power cord is

removed from the receptacle.

2.Block the water outlet of the pool.

3.Unscrew the slag blocking cover (P15) on the

slag blocking barrel in an anticlockwise direction,

take out the slag blocking screen (P13) and the

seal ring (P14).

4.Rinse the slag blocking screen with a water

pipe. If necessary, use a plastic brush to remove

impurities. Do not use a metal brush.

5.Rinse the inside of the slag blocking screen

and the seal ring of the slag blocking barrel with a

water pipe

6.Install the seal ring (P14) of the slag blocking

barrel, the slag blocking screen (P13) and the

FIG. 15

sand lter pump is less than 0.2bar (3psi) (green area) (see FIG. 14), it

runs normally.

cover (P15) of the slag blocking barrel in their original positions (see FIG.

13).

10 SFP3-14-GBwww.jilong.com

Long-term storage and storage in winter

Using the product in a frozen pool may damage the product and

invalidate the quality warranty. If the product has to be used with

antifreeze, propylene glycol may also be used. Propylene glycol is

a nontoxic chemical unharmful to any plastic parts. Other types of

antifreeze are highly toxic and may be harmful to the product’s plastic

elements.

1.Before discharging the water or repostioning of the pool, make sure

the discharge direction is towards the discharging ditch and away

from the home. Review local regulations for special water treatment

requirements.

2.Switch off the product and remove the power plug.

3.After emptying, remove all connected sand lter pumps, corrugated

tubes and lter hoods on the pool wall.

4.Unscrew the drain valve (8) in an anticlockwise direction to completely

empty water inside the body. The drain plug is at the bottom of the

body.

5.Dry the parts of the sand lter pump and corrugated tubes.

6.Lubricate the seal rings and washers in the order below for long-term

storage.

8.The best practice for product storage is to dry the parts and motor

and replace them in the original package. To avoid shrinkage or

corrosion, do not cover or wrap the motor with a plastic bag.

9.Please store the motor and parts in a dry place at 32°F (0°C) ~104°F

(40°C).

2014

11 SFP3-14-GBwww.jilong.com

Diagnosis of Problems and Solutions

Problems Checking Solutions

The motor can not be

started normally

Power plug not properly

inserted

Leakage protection

disconnected

Motor overheated or

overloaded

Causes motor to stop

Make sure the power cord is inserted into

the 3-core grounded metal receptacle.

Reset circuit breaker. If the problem

persists, the power system may be

defective. Power off immediately and

confer with an expert.

Allow the motor to cool naturally and start

it again.

Filter

Unable to rinse the

pool

No sand in the body

Location error of the

control valve

Excessive dirt in water

Filter barrel blocked

Sand filling Refer to sand filling

instructions

The control valve rotates to the filter

position

to prolong the running time

Clean the lter barrel

The lter is unable to

discharge water or

the water ow rate is

too slow

There is blockage at the

inlet

There is an air leakage at

the gap of the inlet

Excessive dirt in water

Filter medium is blocked

by impurities

The pool is connected with

a cleaning device

Check and clear away the blockage in

the water pipes

Tighten the nozzle nuts and check the

damaged point of the nozzle and water

height

Clean the lter screen

Backwash

Disassemble the cleaning device

connected to the pool

Filter fails to run Water level is too low

Filter screen is blocked

Air leakage from the inlet

pipe

Motor or blade is blocked

Inject water to adjust water level

Clean the lter screen in the pool

Tighten the nozzle and check the

damaged point

Replace the ttings

Water leakage on

the control valve or

upper cover

The seal ring of the body

is lost or too dirty

The control valve retainer

is not tightly secured

ordamaged

Remove the upper cover of the control

valve and sleeve the seal ring of the body

Clean the seal ring of the body with a

water pipe

Tighten the screw with a screwdriver

Replace the ttings

The manometer fails

to run

The inner wall of the

manometer is blocked

The manometer is

damaged

Remove the manometer from the control

valve and clear away the impurities on

the inner wall

Replace the ttings

Sand enters the pool The sand particles are too

ne

Use 20# quartz sand only

Particle size of the sand is 0.45-1.25mm

Or replace the sand

12 SFP3-14-GBwww.jilong.com

After Sales Service Centers

For service questions or to order replacement parts, please listed below or visit www.

jilong.com for answers to most frequently asked questions.contract the appropriate ofce

BML UK

Benross House,Bridge Industrial Estate, Speke Hall Road,

Liverpool, L24 9WD, UK

Tel:440151-448-69-73

E-mail: [email protected]

USA / CANADA / MEXICO

JILONG PLASTIC PRODUCTS NORTH AMERICA INC.

271, EAST 2ND AVENUE

VANCOUVER B.C. V5K 1J1 CANADA

Tel:1-866-946-3002

E-mail: [email protected]

DENMARK

HP Schou

Industrivej 67,7080 Borkop

Tel:45-7662-1110

E-mail: service@hpv.dk

FINLAND

HP Schou

Jorvaksen myllytie 5 Jorvas kvarnväg 02420 JORVAS

Tel:358(0)102710424

E-mail: uv@tradewind.

NETHERLANDS / BELGIUM / LUXEMBURG

Aqua-fun

Icarus 11

8448 CJ Heerenveen

Tel. 0031 513 62 66 66

Fax 0031 513 41 80 37

E-mail [email protected]

RUSSIAN

АСБ-Рейтинг

115419, г. Москва, 2-й Донской проезд, д. 7/1

Тел.: +7 (495) 231-35-99 (многоканальный)

по рабочим дням с 9.00 до 18.00

Факс: +7 (495) 231-20-22

Электронная почта: [email protected]

BRAZIL

Sér Marketing & Sales e Representações Ltda

Al. Tambaqui, 59 - Residencial 11 - Alphaville

Santana de Parnaíba/SP

CEP: 06540-300

CNPJ: 02.976.412/0001-97

sac@ser.com.br / 55(11) 4602-1176

FRANCE / ITALY / SPAIN / PORTUGAL

Jilong Europe Srl unipersonale

Via Vitaliano Brancati, 44-00144 Roma – Itali

Tel:France - 0800908976

Italy - 800911531

E-mail:[email protected]

GERMANY / AUSTRIA

HEISSNER GmbH（pools/spas）

Schlitzer Straße 24 D-36341 Lauterbach,Germany

Tel:49-1805- 4347

E-mail: [email protected]

SWEDEN

HP Schou

Åsvägen 2 E,281 37 Hässleholm

Tel:46-451-381-980

E-mail: [email protected]

NORWAY

Osjord

Luramyrveien 64 Postbox 152,4065 Stavanger

Tel:47-51-63-72-00

E-mail: ArntEinar[email protected]

POLAND / CZECH / SLOVAKIA / HUNGARY

SASKA SP. Z O.O.

Ul. Marynarki polskije 59a 80-557 gdansk poland

Tel:+ 48 58 3004633, 3004863

E-mail:[email protected]

CROATIA / SLOVENIA / BOSNIA /SERBIA

Eurom Denis d.o.o

Borongajska 81a, 10000 Zagreb

Hrvatska

tel.:385 1 230 70 00

E-mail: [email protected]

ASIA

上海吉龙塑胶制品有限公司

上海浦东新区川沙黄楼栏学路 460-520 号

Tel:+86-21-58942200

E-mail:[email protected]

JILONG JL29P423NG User manual

JILONG JL29P423NG User manual

JILONG JL29P423NG User manual

Related papers

Other documents