2. Computers & electronics
  3. Networking
  4. Network antennas
  5. Spireon
  6. FL18

Spireon FL18 Installation guide

  • Hello! I am an AI chatbot trained to assist you with the Spireon FL18 Installation guide. I’ve already reviewed the document and can help you find the information you need or explain it in simple terms. Just ask your questions, and providing more details will help me assist you more effectively!
INSTALLATION
FL18
™
,VP2500
™
,VP2502
™
Ifyouhaveanyquestionsregardingyourdevice,
pleasecall:
18778190015
©2015Spireon,Inc.AllRightsReserved.
MountingtheDevice:
MounttheFL18underthevehicle’sdash,labelsideup,usingzip
tiesordoublesidedtape,inalocationthatisclearofanymetallic
obstructionsfromabovethatmightcauseinterferencewithGPS
signalreception
MountingtheAntenna(whenapplicable):
Mounttheantennawiththe3Mtapefacingdownward,onthe
frontleftsideofthedash,nearthevehicle’sApillar
RoutetheCOMandGPSwiresfromtheantennadowntotheFL18
andconnectthemtotheappropriateterminals
MountingtheDriverIDReader(whenapplicable):
Drilla3/8”holeinthelocationonthedashwherethedriverID
readerwillbemounted
FeedthewiresfromthedriverIDreaderthroughthe3/8”holeand
pushthereaderin
Securethereaderfromthebacksideusingthesuppliedpush
washer
ConnecttoPowerandGround:
Locateaconstant12vpowersourceandasuitablechassisground
Connecttheredwireinthedeviceharnessto12vpower
Connecttheblackwireinthedeviceharnesstoground
ConnecttheIgnitionSenseWire:
Usingthevehicle’sservicemanualandadigitalvoltmeter,locatea
switched12vpowersource(receivespowerwiththeignitioninthe
‘on’positionbutdoesnotreceivepowerinthe‘off’or‘acc’
positions)
Connectthewhitewireinthedeviceharnesstotheswitched
powersource
ConnectthePTOInput(whenapplicable):
ConnecttheyellowwireinthedeviceharnesstothePTOtrigger’s
outputwire
ConnecttheDriverIDReader(whenapplicable):
Connecttheblackwire(pin#16)inthedeviceharnesstotheblack
wirefromthedriverIDreader
Connectthewhite/bluewire(pin#17)inthedeviceharnesstothe
graywirefromthedriverIDreader
Ifyouhaveanyquestionsregardingyourdevice,
pleasecall:
18778190015
©2015Spireon,Inc.AllRightsReserved.
IMPORTANTNOTE:
Theswitchedpowersourceshould
read0vwiththekeyinthe‘off‘
positionand11
14vinthe‘on’
position.
CAUTION
:
Usethevehicle’sfactoryservice
manualandadigitalvoltmetertobe
surethatyou’velocatedthe
appropriatewires.
REMEMBER
:
Forproperoperation,theremustbe
anunobstructedlineofsight
betweentheFL18andthesky.Any
metallicobstructionsfromabovewill
resultininterferencewithGPS
reception.
INSTALLATION–FL18
KITCONTENTS
TrackingDevice
ExternalAntenna(optional)
20pinI/Ocable
GarminFMICable(optional)
DriverIDReader(optional)
Connectors/ZipTies
Ifyouhaveanyquestionsregardingyourdevice,
pleasecall:
18778190015
©2015Spireon,Inc.AllRightsReserved.
INSTALLATION–FL18
WireDiagram
–ShortHarness(#1043):
IgnitionSense
+12vDCPower
ChassisGround
PTO
Input2
RelayTrigger
DoorPulse
ToGarmin
Device
GarminFMICable
(optional)
Aux2(Garmin)
DriverIDReader
(optional)
(serialinput–forfactoryuseonly)
PTOInput
(pin#3–blue)
+12vDCPower
ChassisGround
IgnitionSense
FL18Device
Harness(#1125)
FL18Device
Harness(#1043)
Fuse
WireDiagram
–LongHarness(#1125):
/